Академический Документы
Профессиональный Документы
Культура Документы
User Manual
Content
Chapter 1 OMT Software Instruction............................................................................................................................. 4
11 Summary ........................................................................................................... 4
12 Operation Enviroment ............................................................................................ 4
121 Hardware Requirement......................................................................................................................................... 4
122 System Requirement............................................................................................................................................. 4
13 OMT Monitoring Methods ........................................................................................ 5
131 OMT Monitoring Display .................................................................................................................................... 5
132 OMT Monitoring Connection............................................................................................................................... 5
1321 Local Monitoring Connection Display ........................................................................................................... 5
1322 Remote Monitoring Connection Display........................................................................................................ 5
Chapter 2 OMT Software Operation And Application ................................................................................................. 6
21 OMT Monitoring Connection Preparation ..................................................................... 6
211 Equipment Preparation ......................................................................................................................................... 6
212 Operation Preparation........................................................................................................................................ 6
213 OMT Software Installation And Login ................................................................................................................ 6
22 Create New City & Area & Equipment Information .......................................................... 7
221 Create New City ................................................................................................................................................... 7
222 Create New Area .................................................................................................................................................. 8
223 Create New Equipment ........................................................................................................................................ 8
23 Monitoring Operation Methods.................................................................................. 9
231 Local Connection Operation................................................................................................................................. 9
232 Search Site And Search Equipment.................................................................................................................... 10
233 Monitoring Repeater........................................................................................................................................... 14
2331 Read / Write Basic Parameter Information................................................................................................... 14
2332 Read / Write RF Parameter Information....................................................................................................... 17
2333 Read Alarm and Read / Write Enable of Alarm Parameter Information ...................................................... 20
2334 Resume Factory Default Setting................................................................................................................... 23
234 Remote Connection Operation ........................................................................................................................... 24
2341 Set RepeaterQuery/setting phone numberAndReporting number ......................................................... 24
2342 Set RepeaterEquipment Telephone........................................................................................................... 26
2343 Establish Modem Remote Monitoring Communication............................................................................... 27
Chapter 3 OMT Software Functions ............................................................................................................................. 28
~ Page 2 ~
323
The Band Corresponding Relationship Between Alarm Parameters Information Pages Alarm Items
~ Page 3 ~
11 Summary
The software has Parameter Setting, Parameter Queries, Alarm Collection, etc. functions. i. e.
Parameter Setting include repeater serial number setting, monitoring center phone number setting, shift
frequency setting, alarm threshold settings, etc. Parameter Query not only check the setted configuration
information but also can collect real-time repeater working data. Summary, Parameter Query contributes to
the repeater site monitoring and fault diagnosis.
This software owns visual user interface, friendly interface, easy operation, stable and reliable
etc. features.
12 Operation Enviroment
121 Hardware Requirement
(1). PC 1 pcs ( the least requirement as follows );
CPU: Pentium III ( at least 800MHz ) or better processor
Memory: 512MB or larger
~ Page 4 ~
(Figure 1)
(Figure 2)
(Figure 3)
~ Page 5 ~
~ Page 6 ~
(Figure 5)
(Figure 6)
(Figure 7)
(Figure 8)
2. Left click New Equipment to create a monitoring repeater. Fill in the basic information of the monitoring
repeater then click OK to achieve. ( Figure 9 )
~ Page 8 ~
(Figure 9)
(Figure 10)
2. On Communication type please select Local serial port, then on Current Port please select the
corresponding COM port which is connected to the repeater equipment by RS-232. ( Figure 11 )
3. Click Connect, if the selection of the correct COM port, the red light will turn to green color. ( Figure 11 )
~ Page 9 ~
(Figure 11)
(Figure 12)
2. In Equipment Monitoring Information Section please select Basic Parameter Information, left click the
button Search Site on the right lower side. ( Figure 13 )
~ Page 10 ~
(Figure 13)
3. Get the detail information of site number and equipment number which repeater currently connected.
( Figure 14 )
(Figure 14)
4. Please select the corresponding repeater equipment on the left side ( Equipment Management Section )
and right click it, the equipment management function manu will appear. ( Figure 15 )
(Figure 15)
5. Left click Edit Equipment, you will see the equipment basic information input box as shown in figure 16
on the left side.
(Figure 16)
6. Change the site number and equipment number in the dialogue box brought out and ensure that the two
groups of the number are completely match with the numbers as third step youve got. And then click ok.
( As shown in figure 16 on the right side. )
7. Select the corresponding repeater equipment on the left side ( Equipment Management Section ) as
Figure 17:
~ Page 11 ~
(Figure 17)
8. In Equipment Monitoring Information Section please select Basic Parameter Information, left click the
button Search Site on the right lower side. ( Figure 18 )
(Figure 18)
9. Get the detail information which equipment connected, including city , region and the name of
equipment ,the number of site, and the number of equipment etc. ( As shown in figure 19 on the left side. )
And find the corresponding equipment in the main interface of the software shown on the left side.
( Equipment Management Section ) ( As shown in figure 19 on the right side. )
(Figure 19)
~ Page 12 ~
10. Select the corresponding repeater equipment on the left side ( Equipment Management Section ) as
Figure 20:
(Figure 20)
11. In Equipment Monitoring Information Section please select Basic Parameter Information, left click the
button Search Equipment on the right lower side. ( Figure 21 )
(Figure 21)
12. Please wait for seconds and pay attention on feedback section on the right downward inferior, the
Transmit and Receive information of the repeater equipment will appear.
13. When it appears Update the equipment parameters is successful!, means OMT search equipment
procedure and identified in intellectualization successfully, then please go on next step. ( Figure 22 )
(Figure 22)
~ Page 13 ~
(Figure 23)
2. Enter Basic Parameter Information page, pick the items you need to check. ( Figure 24 )
(Figure 24)
3. Click Read button and pay attention on the feedback section on the right downward inferior, there will
be Transmit and Receive message of the repeaters going on the feedback section. ( Figure 25 )
~ Page 14 ~
(Figure 25)
4. When communication is successful, the updated information will immediately appear to the Status
column as bellow charge. ( Figure 26 )
(Figure 26)
(Figure 27)
2. Enter Basic Parameter Information page, pick the items you need to set, input the correct basic
parameters on the corresponding Setting column. ( For example as bellow Figure 28, to set parameters
Query/setting phone number1~5 and Reporting number as 13800138000. )
~ Page 15 ~
(Figure 28)
3. Click Write button and pay attention on the feedback section on the right downward inferior, there will
be Transmit and Receive message of the repeaters going on the feedback section. ( Figure 29 )
(Figure 29)
4. When communication is successful, the updated information will immediately appear to the Status
column as Figure 30.
(Figure 30)
~ Page 16 ~
(Figure 31)
2. Enter RF Parameter Information page, pick the items you need to check. ( Figure 32 )
(Figure 32)
3. Click Read button and pay attention on the feedback section on the right downward inferior, there will
be Transmit and Receive message of the repeaters going on the feedback section. ( Figure 33 )
(Figure 33)
~ Page 17 ~
4. When communication is successful, the updated information will immediately appear to the Status
column as bellow charge. ( Figure 34 )
(Figure 34)
(Figure 35)
2. Enter RF Parameter Information page, pick the items you need to set, input the correct RF parameters
on the corresponding Setting column. ( Figure 36 )
~ Page 18 ~
(Figure 36)
3. Click Write button and pay attention on the feedback section on the right downward inferior, there will
be Transmit and Receive message of the repeaters going on the feedback section. ( Figure 37 )
(Figure 37)
4. When communication is successful, the updated information will immediately appear on the Status
column as Figure 38.
(Figure 38)
~ Page 19 ~
2333 Read Alarm and Read / Write Enable of Alarm Parameter Information
Note: Please refer to the appendix contents in the end of the text for the band corresponding relationship
between alarm parameters basic information page's alarm items with repeater equipments'.
(Figure 39)
2. Enter Alarm Parameter Information page, pick the items you need to check. ( Figure 40 )
(Figure 40)
3. Click Read button and pay attention on the feedback section on the right downward inferior, there will
be Transmit and Receive message of the repeaters going on the feedback section. ( Figure 41 )
(Figure 41)
~ Page 20 ~
4. When communication is successful, the updated information will immediately appear to the Status and
Enable column as Figure 42.
(Figure 42)
(Figure 43)
2. Enter Alarm Parameter Information page, pick the items you need to set, input the correct enable of
alarm parameters on the corresponding Setting column. ( Figure 44 )
~ Page 21 ~
(Figure 44)
3. Click Write(Enable) button and pay attention on the feedback section on the right downward inferior,
there will be Transmit and Receive message of the repeaters going on the feedback section. ( Figure
45 )
(Figure 45)
4. When communication is successful, the updated information will immediately appear to the Enable
column as Figure 46.
(Figure 46)
~ Page 22 ~
(Figure 47)
2. Enter Basic Parameter Information page, pick the items you need. ( Figure 48 )
(Figure 48)
3. Click Default Equipment button and pay attention on the feedback section on the right downward
inferior, there will be Transmit and Receive message of the repeaters going on the feedback section.
4. When it appears Default the repeater is successful!, resume factory default setting sucessfully, please
go on next step. ( Figure 49 )
~ Page 23 ~
(Figure 49)
(Figure 50)
3. Select Local serial port on Communication type, then please select the corresponding COM port
which is connected to the repeater equipment by RS-232 on Current Port. ( Figure 51 )
4. Click Connect button, if the selection of the correct COM port is successful, the red light will turn to
green color. ( Figure 51 )
(Figure 51)
5. Please select the corresponding repeater equipment on the left side. ( Equipment Management Section )
( Figure 52 )
~ Page 24 ~
(Figure 52)
6. Enter Basic Parameter Information page, pick item Query/setting phone number and Reporting
number, set modem SIM card numbers which will be connected to PC in Set Value column. ( Figure 53 )
(Figure 53)
7. Click Write button and pay attention on the feedback section on the right downward inferior, there will
be Transmit and Receive message of the repeaters going on the feedback section. ( Figure 54 )
(Figure 54)
8. When communication is successful, the updated information will immediately appear on the Status
column as Figure 55.
~ Page 25 ~
(Figure 55)
(Figure 56)
2. Left click Edit Equipment, you will see the equipment basic information input box as Figure 57.
~ Page 26 ~
(Figure 57)
3. Input the SIM card number which was inserted into the repeaters, click OK button.
(Figure 58)
3. Select GSM Short message on Communication type, then please select the corresponding COM port
which is connected to modem by RS-232 on Current Port. ( Figure 59 )
4. Click Connect button, if the selection of the correct COM port is successful, the red light will turn to
green color. ( Figure 59 )
~ Page 27 ~
(Figure 59)
5. After the establishment of remote monitoring communication sucessful, users can start to proceed the
remote monitoring. ( Detailed monitoring operation procedures please take 2.3.3 above as reference. )
31 Functions of Sections
(Figure 61)
~ Page 29 ~
(Figure 62)
(Figure 63)
(Figure 64)
~ Page 30 ~
(Figure 65)
~ Page 31 ~
(Figure 66)
(Figure 67)
(Figure 68)
(Figure 69)
~ Page 32 ~
(Figure 70)
(Figure 71)
2. Select New Equipment and the equipment information box will appear. ( Figure 72 )
3. Fill in the master equipment basic information which you are going to create. Then click OK, the
creation is successful. ( Figure 72 )
(Figure 72)
~ Page 33 ~
(Figure 73)
2. Select New Slave Equipment and the equipment information box will appear. ( Figure 74 )
3. Fill in the slave equipment basic information which you are going to create. Then click OK, the creation
is successful. ( Figure 74 )
(Figure 74)
~ Page 34 ~
(Figure 75)
(Figure 76)
2. Left click Edit Equipment, the equipment basic information box will appear. ( Figure 77 )
(Figure 77)
3. Fill in the new information of the repeater then click OK.
~ Page 35 ~
(Figure 78)
2. Click Delete and this step can be successful.
(Figure 79)
2. Click Delete and all repeaters can be deleted.
(Figure 80)
2. Click Delete and all repeaters can be deleted.
~ Page 36 ~
Chapter 4 Appendix
(Figure 81)
(Figure 82)
~ Page 37 ~