Академический Документы
Профессиональный Документы
Культура Документы
Edition 1, 2012
Identification no.
02 07 05 01 000 0 000001
Version no. 0010
Sika Injection-101-RC
Sika Injection-101-RC
Construction
Product
Description
Sika Injection-101-RC is a low viscous, fast foaming and solvent-free waterreactive polyurethane injection foam resin, which cures to a dense flexible foam
with a fine cellular structure.
Uses
Characteristics/
Advantages
Product Data
Form
Colours
Packaging
Storage
Storage Conditions /
Shelf-Life
Part A:
Part B:
Part A:
Part B:
Colourless
Brown
10 or 20 kg
12,5 or 25 kg
Technical Data
Chemical Base
Density
Viscosity
Expansion
System
Information
Application
Conditions/ Limitations
Substrate Temperature
Ambient Temperature
Sika Injection-101-RC
1/3
Application
Instructions
Mixing Ratio
Mixing
1 : 1 parts by volume
- Empty parts A and B into a mixing vessel and mix slowly and thoroughly for at
least 2 min (max. 250 rpm) until homogeneous, thereby observing the safety
precautions. The containers are supplied according to the required mixing
ratio of 1 : 1 parts by volume.
-
Partial quantities can be measured out in separate vessels. After mixing, pour
the material into the pumps feed container, stir briefly and apply within the pot
life.
- After mixing, pour the material into the pumps feed container, stir briefly and
use within the pot life.
If the substrate and/or ambient temperatures are < +10C, Sika Injection-AC10
Dosage of Sika
Injection-AC10 in %
byweight of Sika
Injection-101RC(compoment A+B)
Material temperature
+5C
+10C
+20C
Expansion start
~ 19 sec
~ 17 sec
~ 16 sec
Expansion end
~ 97 sec
~ 88 sec
~ 70 sec
Expansion start
~ 12 sec
~ 11 sec
~ 10 sec
Expansion end
~ 57 sec
~ 49 sec
~ 39 sec
Expansion start
~ 9 sec
~ 8 sec
~ 7 sec
Expansion end
~ 41 sec
~ 37 sec
~ 35 sec
0%
5%
10%
The given data are laboratory parameters and may deviate depending on the
object and conditions on site.
Application Method /
Tools
Cleaning of Tools
Potlife
Notes on Application /
Limitations
Use injection pumps suitable for single part products, such as Sika Injection
Pump EL-1, EL-2, Hand-1 or Hand-2.
Clean all tools and application equipment with Sika .Colma-Cleaner to remove
any polyurethane residue immediately after use. Do not leave Sika .ColmaCleaner in the injection pump. Hardened/cured material can only be removed
mechanically.
Approx. 2 hours (at +20C); remove skin from the surface (do not mix in!)
The waterproofing process is divided into three phases:
Injection:
The time during which the injection material flows under pressure from the pump
to the desired moisture/water containing areas.
Induction:
The time from initial mixing until the reaction starts.
Reaction:
The period during which the mix viscosity increases and foam expansion takes
place.
Sika Injection-101-RC is generally used for the temporary stopping of high water
infiltration. To achieve permanent watertight crack sealing, the subsequent
Local Restrictions
All technical data stated in this Product Data Sheet are based on laboratory
tests.
Actual measured data may vary due to circumstances beyond our control.
Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
Sika Injection-101-RC
2/3
For information and advice on the safe handling, storage and disposal of
chemical products, users shall refer to the most recent Material Safety Data
Sheet containing physical, ecological, toxicological and other safety-related data.
Legal Notes
The information, and, in particular, the recommendations relating to the application and end-use of Sika
products, are given in good faith based on Sikas current knowledge and experience of the product when
properly stored, handled and applied under normal conditions in accordances with Sikas
recommendations. In practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising
out of any legal relationship whatsoever, can be inferred either from this information, or from any written
recommendations, or from any other advice offered. The user of the product must test the products
suitability for the intended application and purpose. Sika reserves the right to change the properties of its
products. The proprietary rights of third parties must be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which will be supplied on request.
Construction
Branches
Surabaya :
Komp. Pergudangan Meiko Abadi III Blok B-52 & B-53, Betro, Gedangan,
Sidoarjo 61254
Tel : 031-8911333; Fax : 031-8916333
Medan :
Jl. Serbaguna (Simp. Jalan Veteran), Kompleks Pergudangan Brayan
Trade Center No. 34, Medan 20239
Tel : 844 6697, 844 6997 ; Fax : (061) 844 6698
Batam :
Jl. Laksamana Bintan, Komp. Bumi Riau Makmur Blok E No.3, Sungai Panas
Tel : (0778) 424928; Fax : (0778) 450189
Sika Injection-101-RC
3/3