Академический Документы
Профессиональный Документы
Культура Документы
RAN14.0
Issue
02
Date
2012-11-30
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
WCDMA RAN
Cell Barring
1 Introduction
Contents
1 Introduction ................................................................................................................................1-1
1.1 Scope ............................................................................................................................................ 1-1
1.2 Intended Audience......................................................................................................................... 1-1
1.3 Change History.............................................................................................................................. 1-1
2 Overview......................................................................................................................................2-1
3 Automatic Operation ................................................................................................................3-1
4 Manual operation ......................................................................................................................4-1
5 Engineering Guidelines ...........................................................................................................5-1
5.1 Application Suggestions ................................................................................................................ 5-1
5.2 Feature Deployment ...................................................................................................................... 5-1
5.2.1 Requirements ....................................................................................................................... 5-1
5.2.2 Data Preparation................................................................................................................... 5-1
5.2.3 Initial Configuration ............................................................................................................... 5-1
5.2.4 Activation Check ................................................................................................................... 5-2
5.2.5 Feature Deactivation ............................................................................................................ 5-5
5.2.6 Example ................................................................................................................................ 5-6
6 Parameters..................................................................................................................................6-1
7 Counters ......................................................................................................................................7-1
8 Glossary ......................................................................................................................................8-1
9 Reference Documents .............................................................................................................9-1
Issue 02 (2012-11-30)
WCDMA RAN
Cell Barring
1 Introduction
1 Introduction
1.1 Scope
This document describes the basic principles of the cell barring feature.
Editorial change: refers to the change in wording or the addition of the information that was not
described in the earlier version.
Document Issues
The document issues are as follows:
02 (2012-11-30)
01 (2012-07-20)
02 (2012-11-30)
This is the document for the second commercial release of RAN14.0.
Compared with RAN14.0 01(2012-07-20), this issue incorporates the changes described in the following
table.
Change Type
Change Description
Parameter Change
Feature change
None.
None.
Editorial change
01 (2012-07-20)
This is the document for the first commercial release of RAN14.0.
Compared with RAN13.0 01(2011-04-30), this issue incorporates the changes described in the following
table.
Issue 02 (2012-11-30)
1-1
WCDMA RAN
Cell Barring
1 Introduction
Change Type
Change Description
Parameter Change
Feature change
None.
None.
Editorial change
Issue 02 (2012-11-30)
1-2
WCDMA RAN
Cell Barring
2 Overview
2 Overview
This document describes the feature WRFD-021102 Cell Barring.
When a cell is abnormal, this feature enables the operator to automatically or manually bar the cell.
When the Iu interface is disconnected, this feature can prevent the UE from initiating useless access
requests and ensure that 3G UEs are handed over to the 2G network.
This feature can provide flexibility for the operator in some scenarios (for example, maintenance).
Manual operation. The operator can bar/unbar the cell by the MML commands. And then RNC will
update the system information of this cell to indicate UE the change;
Automatic operation. In cases of Iu-CS or Iu-PS breakdown, the RNC keeps providing coverage (but
not service) to the UEs under its control. This means that several UEs are kept in 3G coverage, but,
actually, they cannot access the network. If the Iu-CS breaks down, the RNC will bar the CS domain
service for the cell; if the Iu-PS breaks down, the RNC will bar the PS domain service for the cell. In the
case of both Iu-CS and Iu-PS breakdown, RNC bars the cell automatically.
The RAN notifies the UE through SIB about the information of cell barring. And the UE detects SIB and
access the network according to the SIB.
If SIB1 does not contain the information of one CN domain (CS or PS), the UE does not initiate
services in this domain and does not reselect cells but camps in the current cell.
If the SIB3/4 indicates the cell is barred, the UE is not permitted to select/re-select this cell, not even
for emergency calls. UE firstly tries to camp on configured 3G/2G neighboring cells. If all cells can not
be camped on, the UE tries to search new network.
Issue 02 (2012-11-30)
2-1
WCDMA RAN
Cell Barring
3 Automatic Operation
3 Automatic Operation
The RNC take actions according to the faults on the Iu:
If
If
If
SYS_INFO_UPDATE_FOR_IU_RST is turned on, the SIB3/SIB4 indicates the cell is barred. In this
case, the UE will reselect other cell.
If
SYS_INFO_UPDATE_FOR_IU_RST is turned off, the event of Iu-CS and Iu-PS signaling link
disconnection is masked. The SIB1 still contains the CS CN and PS CN information but the
SIB3/SIB4 does not indicate the cell is barred. In this case, the UE can initiate a CS or PS service
request but the RNC will reject the request.
Issue 02 (2012-11-30)
3-1
WCDMA RAN
Cell Barring
4 Manual operation
4 Manual operation
Quick blocking/unblocking of cells is required in some special scenarios. For example, if the RNC is
faulty when the UE camps on the 3G network, the RNC cannot provide complete services on the access
network; if the CN needs to be upgraded, the UE must be forcibly handed over from the 3G network to
the 2G network. Although the BLK UCELL command can be executed to block/unblock cells in batches,
this method requires longer preparation and processing time. Therefore, it does not meet the
requirement for quickly blocking/unblocking cells.
Quick blocking/unblocking of cells is a process of UE access control through the AC control IEs in the
cell system information. It is effective for the UEs in idle mode. The blocking modes are as follows:
Blocking all the cells controlled by an RNC through the ADD URNCALLCELLBLK command. Cell
blocking can be performed in the PS domain or in both the PS domain and the CS domain, which is
set by the DomainType parameter. The processing time of cell blocking is set by the
ProcessDuration parameter.
Blocking PS services for a cell controlled by an RNC by setting the DomainType parameter to PsBlk
in the ADD/MOD UCELLACCESSSTRICT command.
Blocking all the cells belonging to an operator through the ADD UCNOPALLCELLBLK command.
Cell blocking can be performed in the PS domain or in both the PS domain and the CS domain, which
is set by the DomainType parameter. The processing time of cell blocking is set by the
ProcessDuration parameter.
Only one blocking mode can be used for quick blocking/unblocking of cells, that is, the blocking modes based on RNC
and Operator cannot be used simultaneously.
In the latter blocking mode, the ADD UCNOPALLCELLBLK command is executed for only one operator.
Cell blocking can be performed in the PS domain or in both the PS domain and the CS domain, which is
set by the DomainType parameter. The processing time of cell blocking is set by the ProcessDuration
parameter.
Table 4-1 provides five schemes for quickly blocking/unblocking cells.
Table 4-1 Five schemes for quickly blocking/unblocking cells
Target
Object
Blocked
Domain
RNC
PS domain Delete the information about the PS domain from Any new PS service is
SIB1. Only the information about the CS domain is rejected. This scheme is
broadcast.
effective for all the UEs.
RNC
CS domain Set all the ACs in the "Access Class Barred list" IE Any new service is
and PS
in SIB3/4 to barred.
rejected. This scheme is
domain
In addition, set all the ACs in the "Domain Specific effective for all the UEs.
Access Restriction Parameters For All" IE in the
"Domain Specific Access Restriction For Shared
Network" IE to barred.
Operator
Issue 02 (2012-11-30)
Scheme
UE Version
Compatibility
4-1
WCDMA RAN
Cell Barring
4 Manual operation
Target
Object
Blocked
Domain
Operator
CELL
PS domain Delete the information about the PS domain from Any new PS service is
SIB1. Only the information about the CS domain is rejected. This scheme is
broadcast.
effective for all the UEs in
the cell.
Issue 02 (2012-11-30)
Scheme
UE Version
Compatibility
Any new service is
rejected. This scheme is
effective for the UEs of
3GPP Release 6 or later.
4-2
WCDMA RAN
Cell Barring
5 Engineering Guidelines
5 Engineering Guidelines
5.1 Application Suggestions
The use of this feature does not affect the KPI of local network, because after the cell is barred the UE
will not retry to access the local cell. But the UE will try to access inter-RAT cells or inter-operator cells in
the same coverage and cause signaling shock to them. So you need to consider the anti-shock
capability when deploying this feature and ensure the cell can work normally when a lot of UEs come to
the cell.s
It is recommended to use the default parameters of the feature.
Run the BSC6900 MML command BLK UCELL to set Priority (Priority) to HIGH.
--End
To unblock a cell, run the following command:
Issue 02 (2012-11-30)
5-1
WCDMA RAN
Cell Barring
5 Engineering Guidelines
Step 1 Run the BSC6900 MML command UBL UCELL To unblock a cell.
--End
Step 1 Click to display Uu Interface Trace on the BSC6900 LMT. Under Uu Message Type, select
RRC_SYS_INFO_TYPE1.
Step 2 View whether information element (IE) information of the PS domain is contained in the traced
messages. Expected result: PS domain IE information is not contained, as shown in Figure 5-1.
--End
Issue 02 (2012-11-30)
5-2
WCDMA RAN
Cell Barring
5 Engineering Guidelines
Block CS and PS domains, CS and PS domains are disconnected, or block the CS domain and turn on
BARRED_CELL_FOR_CSDOMAIN_RST. Perform the following steps to verify whether this feature is
activated:
Step 1 Click to display Uu Interface Trace on the BSC6900 LMT. Under Uu Message Type, select
RRC_SYS_INFO_TYPE3.
Step 2 View whether IE information related to CS and PS domains is contained in the traced messages.
Expected result: The IE information is not contained, as shown in Figure 5-2.
--End
Issue 02 (2012-11-30)
5-3
WCDMA RAN
Cell Barring
5 Engineering Guidelines
Bar PS services of UEs served by an operator. Perform the following steps to verify whether this feature
is activated:
Perform the same verification procedure when barring CS services of UEs served by an operator.
Step 1 Click to display Uu Interface Trace on the BSC6900 LMT. Under Uu Message Type, select
RRC_SYS_INFO_TYPE3.
Step 2 View whether IE information related to CS and PS domains is contained in the traced messages.
Expected result: The IE information is not contained, as shown in Figure 5-3.
--End
Issue 02 (2012-11-30)
5-4
WCDMA RAN
Cell Barring
5 Engineering Guidelines
Issue 02 (2012-11-30)
5-5
WCDMA RAN
Cell Barring
5 Engineering Guidelines
the RNC; CME batch modification center: not supported) to remove parameters related to
operator-specific barring of all cells in a network.
--End
5.2.6 Example
//Activating Cell Barring
SET URRCTRLSWITCH: PROCESSSWITCH = SYS_INFO_UPDATE_FOR_IU_RST-1;
SET URRCTRLSWITCH: PROCESSSWITCH = BARRED_CELL_FOR_CSDOMAIN_RST-1;
SET UIUTIMERANDNUM: CnOpIndex=0, CNId=0, StateIndTmr=20000;
//Deactivating Cell Barring
SET URRCTRLSWITCH: PROCESSSWITCH = SYS_INFO_UPDATE_FOR_IU_RST-0;
SET URRCTRLSWITCH: PROCESSSWITCH = BARRED_CELL_FOR_CSDOMAIN_RST-0;
.
Issue 02 (2012-11-30)
5-6
WCDMA RAN
Cell Barring
6 Parameters
6 Parameters
Table 6-1 Parameter description
Paramete NE
r ID
MML
Feature Feature
Command ID
Name
Description
Issue 02 (2012-11-30)
6-1
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
Default Value:1
Priority
BSC69 BLK
00
UCELL
WRFD-0 Admission
20101 Control
Meaning:
1.There are three block priorities: high, normal and
low.
2.High priority: Blocking a cell immediately.
3.Normal priority: Blocking a cell once there are no
users in it for a specified time, or blocking it even if
there are some users when the specified time
expires.
4.Low priority: Blocking a cell when there are no
users in the cell.
Meaning:1)INVOKE_TRACE_SWITCH.
PROCES BSC69 SET
WRFD-0 3GPP R9
SSWITCH 00
URRCTRL 10101 Specification
When it is checked, RNC will start Invoke Trace
SWITCH
s
WRFD-0
procedure upon receiving INVOKE TRACE
20124 Uplink Flow Message form CN, otherwise, RNC won't start the
Control of
Invoke Trace procedure though it receives the
WRFD-1 User Plane INVOKE TRACE message.
40206
Layered
2)SYS_INFO_UPDATE_FOR_IU_RST.
Paging in
URA_PCH When it is checked, RNC will broadcast SYSTEM
INFORMATION messages to UE when Iu
Issue 02 (2012-11-30)
6-2
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
transmission failure occurs, otherwise, RNC won't
broadcast SYSTEM INFORMATION messages to
UE when Iu transmission failure occurs.
3)DRNC_DIRECT_DSCR.
When it is checked, DRNC will start DSCR
procedure directly in RRC states other than
CELL_DCH, otherwise, DRNC will transfer RRC
CELL UPDATE message to SRNC.
4)RNC_SHARE_SWITCH.
When it is checked, the traffic sharing function is
enabled, otherwise, the traffic sharing function is
disabled, service access will be affected under
heavy traffic.
5)RNCAP_IMSI_HO_SWITCH.
When it is checked, Imsi handover function will be
used, otherwise it will be not used.
6)TERMINAL_VERSION_DEBASE_SWITCH.
When it is checked, terminal version R4 will
debase to R99.
7)SYS_HO_OUT_CIPHER_SWITCH.
When it is checked, the RNC will add ciphering
byte at GSM HANDOVER COMMAND if the GSM
system do not add any cipher information at that
message.
8)SYS_HO_CIPHER_CONFIG.
When it is checked, the cipher configuration in the
added cipher byte in GSM will be A5/1.When it is
no checked ,the cipher configuration is A5/0.
9)BARRED_CELL_FOR_CSDOMAIN_RST.
When it is checked, cell will be bared when CS
domain is invalid, otherwise the CS domain will be
bared when CS domain is invalid. It is invalid If
SYS_INFO_UPDATE_FOR_IU_RST is not
checked.
10)CR2284R1_SWITCH.
In section 8.6.6.28 of TS25.331 of R5 Before2006,
it describes that the HFN should add one when
UE is ciphering in the situation of Timing
re-initialized hard handover, while not specified in
RB SETUP process in the section of 8.6.4.3. so it
is not clear whether to add or not in RB SETUP in
DRD scenarios. CR2284R1 clarify that HFN
Issue 02 (2012-11-30)
6-3
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
should add one in RB SETUP process with Timing
re-initialized hard handover. when it is
checked ,RNC accepts this CR2284R1; when it is
not checked ,RNC does not accept this
CR2284R1.
11)CDT_MSG_FULL_TRACE.
When it is checked, CDT trace function which
starts tracing from message RRC CONNECT
REQUEST.
12)CR2284R1_COMPATIBLE_SWITCH.
CR2284R1 causes the compatible problem. if UE
is not consistent with RNC regarding whether
accept the CR2284R1 or not, it will cause the
problem of streaming when UEs are
communicating with each other. So RNC creates
this switch. when it is checked, RNC is
auto-adaptive to accept the CR2284R1 according
to UE version information. The principles that
RNC judges UE whether to accept the CR2284R1
are as follows: R5 and above UE accepts the CR;
R99/R4 UE, if it receives the START LIST value
from RB SETUP COMPLETE,RNC figures that
UE accepts the CR; R99/R4 UE, if it only receives
the START value from RB SETUP
COMPLETE,RNC figures that UE does not accept
the CR; when it is not checked, whether RNC
accept the CR or not is according to
CR2284R1_SWITCH. The relations between
these two switches CR2284R1_SWITCH and
CR2284R1_COMPATIBLE_SWITCH are as
follows:
(1)CR2284R1_COMPATIBLE_SWITCH is
checked, RNC is self-compatible, so the
CR2284R1_SWITCH is invalid;
(2)CR2284R1_COMPATIBLE_SWITCH is not
checked, the CR2284R1_SWITCH is valid.
13)COMBINE_OPERATION_DRD_SWITCH.
When it is on, RNC will not reject the message RB
SETUP CMP without the IE active time.
14)UL_INTER_PROTECT_SWITCH.
When the switch is off, RNC will not do integrity
protection check for uplink RRC messages.
15)FAST_DORMANCY_SWITCH.
When it is checked, RNC will apply FAST
Issue 02 (2012-11-30)
6-4
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
DORMANCY function.
16)SYS_HO_IN_CIPHER_SWITCH.
When it is checked, don't receive the encrypted
ability information from RELOC REQ ,default
configured of encrypted parameter are UIA1 and
UEA0.
17)PTT_EARLY_TRANS_SWITCH_OFF.
When it is checked, PTT user will not apply the
early transmission function, otherwise, PTT user
will apply the early transmission function.
18)UPLINK_MDC_ENHENCEMENT_SWITCH.
This switch has become invalid.
19)NODEB_PRIVATE_INTERFACE_SWITCH.
When it is checked, the NodeB private interface
data can be taken to the NodeB through the IUB
protocol message.
20)PTT_SPEC_LI_SWITCH_OFF.
When it is checked, special LI will not be used for
PTT user, otherwise, special LI will be used for
PTT user.
21)RNC_DF_2_URA_PCH_SWITCH.
When it is checked, RNC will support transferring
Fast Dormancy UE from CELL_DCH or
CELL_FACH to URA_PCH. When it is not
checked, RNC will not support transferring Fast
Dormancy UE from CELL_DCH or CELL_FACH to
URA_PCH.
22)FD_TAC_MATCH_SWITCH.
When it is checked, RNC will apply FAST
DORMANCY function for UE whose TAC is
configured in database. When it is not checked,
RNC will apply FAST DORMANCY function for UE
whose version is R5 or later.
23)NONPTT_L1_FAST_SYNC_SWITCH.
When this switch is turned on, if a UE sets up a
non-PTT service on the DCH, the BSC6900
includes the Post-verification period information
element (IE) in a Uu message to instruct the UE to
perform concurrent uplink and downlink
synchronization.
When this switch is turned off, if a UE sets up a
Issue 02 (2012-11-30)
6-5
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
non-PTT service on the DCH, the BSC6900 does
not include the Post-verification period IE in a Uu
message. The UE first performs downlink
synchronization and then uplink synchronization.
24)URAPCH_LAYERED_PAGING_RT_SWITCH.
Whether the BSC6900 allows Layered Paging in
URA_PCH for a UE processing real-time services.
When this switch is turned on, the BSC6900
sends paging messages to the cell on which a UE
processing real-time services camped recently
and to the neighboring cells of this cell. The
BSC6900 pages the UE in the entire UTRAN
registration area (URA) only when it does not
receive a response from the UE. This significantly
reduces the number of paging messages on the
Uu interface.
When this switch is turned off, the BSC6900
directly pages the UE in the entire URA.
25)URAPCH_LAYERED_PAGING_NRT_SWITC
H.
Whether the BSC6900 allows Layered Paging in
URA_PCH for a UE processing non-real-time
services.
When this switch is turned on, the BSC6900
sends paging messages to the cell on which a UE
processing non-real-time services camped
recently and to the neighboring cells of this cell.
The BSC6900 pages the UE in the entire URA
only when the BSC6900 does not receive a
response from the UE. This significantly reduces
the number of paging messages on the Uu
interface.
When this switch is turned off, the BSC6900
directly pages the UE in the entire URA.
GUI Value Range:INVOKE_TRACE_SWITCH,
SYS_INFO_UPDATE_FOR_IU_RST,
DRNC_DIRECT_DSCR, RNC_SHARE_SWITCH,
RNCAP_IMSI_HO_SWITCH,
TERMINAL_VERSION_DEBASE_SWITCH,
SYS_HO_OUT_CIPHER_SWITCH,
SYS_HO_CIPHER_CONFIG,
BARRED_CELL_FOR_CSDOMAIN_RST,
CR2284R1_SWITCH, CDT_MSG_FULL_TRACE,
CR2284R1_COMPATIBLE_SWITCH,
COMBINE_OPERATION_DRD_SWITCH,
UL_INTER_PROTECT_SWITCH,
Issue 02 (2012-11-30)
6-6
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
FAST_DORMANCY_SWITCH,
SYS_HO_IN_CIPHER_SWITCH,
PTT_EARLY_TRANS_SWITCH_OFF,
UPLINK_MDC_ENHENCEMENT_SWITCH,
NODEB_PRIVATE_INTERFACE_SWITCH,
PTT_SPEC_LI_SWITCH_OFF,
RNC_DF_2_URA_PCH_SWITCH,
FD_TAC_MATCH_SWITCH,
NONPTT_L1_FAST_SYNC_SWITCH,
URAPCH_LAYERED_PAGING_RT_SWITCH,
URAPCH_LAYERED_PAGING_NRT_SWITCH
Actual Value Range:INVOKE_TRACE_SWITCH,
SYS_INFO_UPDATE_FOR_IU_RST,
DRNC_DIRECT_DSCR, RNC_SHARE_SWITCH,
RNCAP_IMSI_HO_SWITCH,
TERMINAL_VERSION_DEBASE_SWITCH,
SYS_HO_OUT_CIPHER_SWITCH,
SYS_HO_CIPHER_CONFIG,
BARRED_CELL_FOR_CSDOMAIN_RST,
CR2284R1_SWITCH, CDT_MSG_FULL_TRACE,
CR2284R1_COMPATIBLE_SWITCH,
COMBINE_OPERATION_DRD_SWITCH,
UL_INTER_PROTECT_SWITCH,
FAST_DORMANCY_SWITCH,
SYS_HO_IN_CIPHER_SWITCH,
PTT_EARLY_TRANS_SWITCH_OFF,
UPLINK_MDC_ENHENCEMENT_SWITCH,
NODEB_PRIVATE_INTERFACE_SWITCH,
PTT_SPEC_LI_SWITCH_OFF,
RNC_DF_2_URA_PCH_SWITCH,
FD_TAC_MATCH_SWITCH,
NONPTT_L1_FAST_SYNC_SWITCH,
URAPCH_LAYERED_PAGING_RT_SWITCH,
URAPCH_LAYERED_PAGING_NRT_SWITCH
Unit:None
Default
Value:INVOKE_TRACE_SWITCH-0&SYS_INFO_
UPDATE_FOR_IU_RST-0&DRNC_DIRECT_DSC
R-0&RNC_SHARE_SWITCH-1&RNCAP_IMSI_H
O_SWITCH-0&TERMINAL_VERSION_DEBASE_
SWITCH-0&SYS_HO_OUT_CIPHER_SWITCH-0
&SYS_HO_CIPHER_CONFIG-1&BARRED_CEL
L_FOR_CSDOMAIN_RST-0&CR2284R1_SWITC
H-0&CDT_MSG_FULL_TRACE-0&CR2284R1_C
OMPATIBLE_SWITCH-1&COMBINE_OPERATIO
N_DRD_SWITCH-1&UL_INTER_PROTECT_SWI
TCH-0&FAST_DORMANCY_SWITCH-0&SYS_H
O_IN_CIPHER_SWITCH-0&PTT_EARLY_TRAN
S_SWITCH_OFF-0&UPLINK_MDC_ENHENCEM
ENT_SWITCH-0&NODEB_PRIVATE_INTERFAC
Issue 02 (2012-11-30)
6-7
WCDMA RAN
Cell Barring
Paramete NE
r ID
6 Parameters
MML
Feature Feature
Command ID
Name
Description
E_SWITCH-0&PTT_SPEC_LI_SWITCH_OFF-0&
RNC_DF_2_URA_PCH_SWITCH-0&FD_TAC_M
ATCH_SWITCH-0&NONPTT_L1_FAST_SYNC_S
WITCH-0&URAPCH_LAYERED_PAGING_RT_S
WITCH-0&URAPCH_LAYERED_PAGING_NRT_
SWITCH-0
Issue 02 (2012-11-30)
6-8
WCDMA RAN
Cell Barring
7 Counters
7 Counters
Table 7-1 Counter description
Counter
Description
NE
Feature ID
Feature Name
50342548
Cell Barring
50342549
Cell Barring
50342550
VS.ULCE.Max.Shared
Maximum Shared
Uplink CE
NodeB WRFD-021102
Cell Barring
50342554
VS.DLCE.Max.Shared
Maximum Shared
Downlink CE
NodeB WRFD-021102
Cell Barring
Issue 02 (2012-11-30)
7-1
WCDMA RAN
Cell Barring
8 Glossary
8 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
Issue 02 (2012-11-30)
8-1
WCDMA RAN
Cell Barring
9 Reference Documents
9 Reference Documents
None.
Issue 02 (2012-11-30)
9-1