Академический Документы
Профессиональный Документы
Культура Документы
MTCS
1) Threaded end of bolt is always blunt
2) Threaded end of bolt is always pointed
3) Threaded end of screw is always blunt
4) Threaded end of screw is always pointed
2. In UNF thread
1) 14 threads per inch
2) 12 threads per inch
3) 18 threads per inch
4) 32 threads per inch
3. 4-28 thread indicates
1) inch diameter bolt has 2-8 thread per inch
2) inch diameter bolt has 28 thread per inch
3) inch diameter bolt has 2-8 inch length
4) 1/28 inch diameter bolt has 2-8 inch length
4. Aircraft screws are made of
1) Class 1
2) Class 2
3) Class 3
4) Class 4
5. Aircraft bolts are made of
1) Cadmium or zinc plated CRS
2) Un-plated CRS
3) Anodized Al alloy
4) Any one of the above.
6. Which bolt require tight drive fit
1) Internal wrenching bolt
2) Close tolerance bolt
3) Eye bolt
4) Special purpose bolt
7. AN 73 is
1) Hex head bolt
2) Drilled hex head bolt
3) Close tolerance bolt
4) Internal wrenching bolt
8. Internal wrenching bolt may be of
1) MS standard
2) NAS standard
3) AN standard
4) Both 1 & 2
9. MTCS regarding Hex head bolt
1) Takes both tension and shear load where a light drive
fit is permissible
2) Alloy steel bolts smaller than 10-32 and diameter may
be used in primary structure.
3) Al alloy nut and bolts are used where they are
repeatedly removed and closed for maintenance.
4) Al alloy nuts should not be used with cadmium plated
steel bolts on land plane.
10. Which bolt is used only in shear load
1) Close tolerance bolt
2) Internal wrenching bolt
3) Clevis bolt
4) Eye bolt
11. Which bolt not to be used in tension load
1) Internal wrenching
2) Hex head
3) Drilled hex head
4) Clevis
12. Which information is not provided by bolt part number
1) Bolt Diameter
2) Bolt length
3) Bolt grip length
4) Material
13. Bolt made of CRS is indicated by
1) Part number
2) Single raised dash on head
3) Double raised dash on the head
4) Raised triangle on the bolt head
14. In AN3DD5A, A indicates
1) Head is drilled
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
2) Head is undrilled
3) Shank is drilled
4) Shank is undrilled
In AN3DDH5A, A indicates
1) Head is drilled
2) Head is undrilled
3) Shank is drilled
4) Both 1 & 2
MTCS regarding Jo-bolt
1) Bolt is held and nut is turned.
2) High shear and tensile strength.
3) Used in area which is subjected to replacement or
servicing?
4) All
Diameter of Jo-bolt of 375 series
1) 3/16
2)
3) 5/16
4) 3/8
MTCS regarding Lock bolt
1) Lightweight and strength less than the standard bolts.
2) Used to attach two material permanently
3) They are easily removable compared to nut and bolt
4) All are correct
Lock bolt after installation is removed by
1) Drill
2) Pliers
3) Cold chisel
4) No need to remove it
Nut can be identified by
1) Identification marking
2) Letters appearing on the nut
3) Their construction
4) All are correct
Which nut is preferred where desired tightness is obtained
by finger
1) Check nut
2) Light hex nut
3) Wing nut
4) All are correct
Which nut is employed as a locking device
1) Check nut
2) Light hex nut
3) Wing nut
4) All are correct
Which nut cannot withstand large tensional loads
1) Castle nut
2) Castellated shear nut
3) Plain hex nut
4) None
Which self locking nut is of fibre insert type
1) Boots self locking nut
2) Stainless steel self locking nut
3) Elastic stop nut
4) Both 1 & 2
MTCS regarding elastic stop nut
1) It consists of threaded locking collar
2) Locking collar is unaffected by ordinary solvents such
as ether, gasoline etc.
3) Both 1 & 2 are correct
4) As in 3 and will not damage bolt thread or plating.
MTCS Regarding elastic stop nut
1) Locking efficiency of elastic stop nut reduces by using
many times.
2) Tap the fibre locking insert for proper installation
3) It should not be used in place where temperature is
higher than 2500 F
4) All are correct
MS 20363 through MS 20367 are
1) General purpose nut
2) Self locking nuts
3) Internal and external wrenching nut
4) Washer
28. AN-935 is
1) Plain Washer
2) Lock washer
3) Special Washer
4) None
29. Aircraft control cable vary in diameter, ranging from
1) 1/16 to 3/16 inch
2) 1/16 to inch
3) 1/16 to 3/8 inch
4) 3/16 to 3/8 inch
30. Cable used in primary control system
1) 77 cable
2) 719 cable
3) 17 cable
4) Medium flexible cable
31. 719 cable vary in diameter, ranging from
1) 1/16 to 3/16 inch
2) 1/16 to inch
3) 1/16 to 3/8 inch
4) 1/8 to 3/8 inch
32. MTCS regarding turnbuckle
1) When installing a turnbuckle in control system, screw
both the terminals an equal number of turns over the
barrel
2) End of the barrel with right hand threads can be
identified by a groove or knurl around the end of the
barrel.
3) After adjustment of turnbuckle, it must be safetied.
4) Both1 & 3 are correct.
33. Turnbuckle terminal should bee screwed into the barrel
until
1) Not more than 3 threads are exposed on either side
of the barrel
2) At least 3 threads are exposed on either side of the
barrel
3) At least 3 threads are exposed on left hand thread
side
4) At least 3 threads are exposed on right hand thread
side
34. Specification of threaded cable terminal is
1) AN 663
2) AN 666
3) AN 667
4) AN 668
35. Push pull tube is made of which material
1) Al Alloy
2) CRS
3) Cadmium plated steel
4) All
36. Flat head pin is also called
1) Taper pins
2) Clevis Pins
3) Cotter Pins
4) Roll pins
37. Pin used in joints which carry shear loads and where
absence of play is essential
1) Taper pins
2) Clevis Pins
3) Cotter Pins
4) Roll pins
38. Most commonly pin used to lock the bolts, screws, nuts
1) Taper pins
2) Clevis Pins
3) Cotter Pins
4) Roll pins
39. 2017 T is
1) Field rivet
2) As in 1 & need no further treatment
3) As in 1 & must be stored in cold storage
4) Ice box rivet
40. 2117 T is
1) Field rivet
2) As in 1 & ready to use as received
3) As in 2 & need on further heat treatment
4) As in 3 & hardened with age
41. 2024 T rivet must be used
1) Within 1 hrs , when taken from refrigeration
2) Within 10 20 min. when taken from refrigeration
3) As in 1 & hardened with age
4) As in 2 & hardened with age
42. MTCS
1) Single wire method is the most common method of
safety wiring.
2) In double twist method a group of three should be
minimum.
3) Safety wired of nuts and bolts in a group is wired in
series rather than individual
4) All
43. MTCS regarding cotter pin
1) The prong bent over the bolt end should be extending
beyond the bolt diameter.
2) The prong bent down should not rest against the
surface of the washer.
3) The prong should not extend outward from the sides
of the nut.
4) All
44. In double wrap safety method, remaining length of safety
wire should be wrapped
1) At least four turns around the shank
2) At least three turns around the shank
3) Maximum four turns around the shank
4) Maximum three turns around the shank
45. Which is called field rivet
1) 2117 T
2) 2017 T
3) 2024 T
4) 5056
46. For riveting firewall, exhaust stack bracket which rivet is
used
1) 2024 T rivet
2) 5056 rivet
3) Mild steel rivet
4) Corrosion resistance steel rivet
47. In wire safety, what should be size of pigtail made at the
end of the wiring
1) to inch
2) to 3/2 inch
3) to 3/2 inch
4) Depending on the size of the wire
48. MTWS regarding safety wiring
1) The pigtail should not be bent back or under to
prevent it from becoming a snag.
2) The wire must be applied so that all pull exerted by
the wire tends to tightens the wire.
3) If the loop around the head stay down the bolt head,
causing the slack loop.
4) None
49. Shop head of rivet serves same function as
1) Another head of rivet
2) A bolt head
3) A nut on the bolt
4) A screw head
50. Rivet creates a bond that
1) Must have more strength than that of material being
joined
2) At least as strong as material being jointed
3) Must have less strength than that of material being
joined.
51. Protective coating on rivet is indicated by
1) Special marking on the head of rivet
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
2) Colour of rivet
3) Both 1 & 2
4) None
Raised double dash on the head of rivet indicates
1) 2117 T
2) 2017 T
3) 2024 T
4) Carbon steel
Which material does not fall in same group for dissimilar
metal corrosion
1) 5052
2) 7075
3) 2017
4) 2117
Riveting of thin sheet metal (specially empennage skin),
which rivet is used
1) Flat head rivet
2) Brazier head
3) Countersunk rivet
4) None
AN 470 & MS 20470 indicates
1) 100 countersunk head
2) Universal head
3) Brazier head
4) Round head
In AN 470 AD 3 5 specification, AD indicates
1) 2017 T, Al alloy rivet
2) 2117 T, Al alloy rivet
3) 2024 T, Al alloy rivet
4) As in 1 & it is an ice box rivet
In rivet specification AN 426 DD 3 5, 5 indicates
1) Length of rivet is 5/16 inches including head
2) Length of rivet is 5/16 inches excluding head
3) Length of rivet is 5/32 inches excluding head
4) Length of rivet is 5/32 inches including head
In aircraft countersunk rivet, angle of countersunk
1) 100
2) 78
3) As in 1 for more surface contact to hold in place
4) As in 2 for less surface contact to reduce friction
Stem of self plugging rivet may consists
1) Knot
2) Knob
3) Serrated portion
4) Any one of the above
MTCS
1) Shank of the rivet should extend beyond the material
thickness by approximately 3/64 to 1/8
2) As in 1 & after the stem is pulled
3) As in 1 & before the stem is pulled
4) Shank of the rivet should extend beyond the material
thickness by 3/16 to 1/8
Which blind rivet is interchangeable structurally with solid
rivet
1) Self plugging (friction lock) rivet
2) Pull thru rivet
3) Bulbed cherry lock rivets
4) Huck mechanical lock rivets
Grip length of blind rivet means
1) Total length of rivet including head
2) Total length of rivet excluding head
3) Total sheet thickness to be riveted
4) Total length of shank except mandrel
Unisink
1) Combination of countersink and protruding head
2) As in 1 & strength is more than double dimpling
3) As in 1 & strength is less than double dimpling
4) As in 1 & strength is equal to the double dimpling
A large diameter, shallow countersink head provide wide
area for
1) High vibration application
2) Honeycomb operation
65.
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.