Академический Документы
Профессиональный Документы
Культура Документы
PE Water
Pipes
According to EN 12201 | ISO 4427
03
OIT to
ISO 11357-6/
EN 728
Model No. H3003
06
Volatile Content to
ISO 12099
Model No. H3004
09
Density to
ISO 1183
Model No. H3002
04
Carbon Black
Content to
ISO 6964
Model No. 1398
07
Water Content to
EN 12118
Model No. H3021
05
Carbon Black
and Pigment
Dispersion to
ISO 18553
Model No. H3009/
H3022
08
Heat Reversion
Test to ISO 2505
Model No.
H3014/1291
11
10
Internal Pressure
Test to ISO 1167/
ASTM D 1598
Model No.
1720/17501760
Resistance to
Rapid Crack
Propagation to
ISO 13477
Model No.
1629/1671
Resistance to
Slow Crack Growth
to ISO 13479
Model No. 1653
Elongation at
Break to ISO 6259
Model No. H3016
Specimen Milling
Machine for
Preparation of
Test Bars
Model No. 1643
www.iptnet.de
12
15
14
13
16
02
Automatic supervision
Comprehensive configuration
possibilities
Decentralized control
Automatic documentation
03
IptDataLogging
< LDPE
< 0.925 g / cm
0.926
< MDPE
< 0.940 g / cm
0.941
< HDPE
< 0.962 g / cm
04
The MFR value should not, after extrusion, differ from the
nominal mean given by the compound producer by more
than 20 %.
05
06
40
More than
years experience.
Our strength lies in our versatility, problem solving,
quality and competitiveness. We invite you to share
in our successful 40traditional years of service.
07
08
09
10
During this test, the samples are placed in an oven with hot
air circulation of (110 2 C) for at least 60 min (depending
upon the wall thickness of the pipe) and then the decrease of
the sample length as compared to the original length is
calculated. Following the thermal exposure and after cooling
down, the length of pipe sample will become shorter. This
could lead to the change in roundness of the installed pipes.
Therefore, having completed the test, the standard limit
of linear changes (approximately up to 3 %) will be
studied in the laboratory. The pipe shall show no delamination, cracks or bubbles.
11
The major test which can assure the pipes life time is the
hydrostatic pressure test. The test is used to examine a polymer creep behaviour and is the basis on which the pressure
rating, required dimensions or anticipated service life of
pipes (over 50 years) can be determined.
40
More than
years experience.
Our strength lies in our versatility, problem solving,
quality and competitiveness. We invite you to share
in our successful 40traditional years of service.
12
13
14
Elongation at Break
to ISO 6259
Model No. H3016
Tensile test is a shortened inspection method to determine the tensile properties, in particular the stress at yield
and elongation at break, of PE pipes. Occurred failures of PE
pipes are classified as ductile or brittle, whereas the ideal behavior of PE pipes is ductile, for which a high force and travel
is required in order to obtain the required elongation range of
the dumbbells of over 350 %.
15
The IPT CNC-controlled unit has been specifically developed to meet the requirements of plastic pipe manufacturers, and is capable of accommodating even the
largest test bars required for PE pipes. Customized test
specimen according to various standards such as EN, ISO,
ASTM, etc. are available upon request.
40
More than
years experience.
Our strength lies in our versatility, problem solving,
quality and competitiveness. We invite you to share
in our successful 40traditional years of service.
16