Академический Документы
Профессиональный Документы
Культура Документы
BPA Site,Rajgir
SUMMARY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
S.No.
Particulars
Civil
Plumbing
Electrical
GRAND TOTAL
(1A)
(1B)
(1C)
SR
CPWD
NSR
S.No. Description
1
Cum.
850
Cum.
Cum.
3402
Mtr.
62
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth
upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of
50m outside the periphery of the area cleared.
100 Sqm.
4315
Supplying and Filling in plinth with local sand and under floors including, watering, ramming
consolidating and dressing complete.
Cum.
3348
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers
not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead.
Excavating trenches of required width for pipes cables etc, including excavation for sockets, and
dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and
then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each
deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a
lead of 50 m.
All kinds of soil.
Pipes, cables etc. exceeding 80mm dia. But not exceeding 300mm dia.
Amount
Earth work in excavation over areas (exceeding 30 cm in depth 1.5 m in width as well as 10 sqm on
plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m disposed earth to be
levelled and neatly dressed.
All Kind of soil
Rate
Qty
Page 1
Along external wall where the apron is not provided using chemical imulsion @ 7.5 liters/sqm of the
vertical surface of the substructure to a depth of 300mm including excavation channel along the wall &
rodding etc. complete.
With chlorphyriphos/Lindone E.C. 20% with 1% concentration
10
Mtr.
666
Sqm.
5565
Mtr.
490
Cum.
635
Sqm
415
14
706
Treatment of existing masonry using chemical emulsion @ one litre per hole, 300mm interval
including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse
sand) to the full depth of the hole.
With chlorphyriphos E.C. 20% with 1% concentration
13
Mtr.
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart
including drilling and plugging 12mm diameter holes with cement mortar 1:2 (1 cement : 2 coarse
sand) to match the existing floor.
With chlorphyriphos E.C. 20% with 1% concentration
12
8060
Along the external wall below concrete or masonry apron using chemical emulsion @ 2.55 litres per
linear metre including drilling and plugging holes etc.
With chlorphyriphos E.C. 20% with 1% concentration
11
Litre
Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20mm nominal size).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Page 2
15
16
17
18
19
Extra for providing and mixing waterproofing material in cement concrete work in proportion Per bag of
recommended by the manufacturers.
50 Kg. of
cement.
Applying a coat of required petroleum bitumen of penetration 80/100 of approved quality using
1.7kg/m2 on damp proof course after cleaning the surface with brushing and finally with a piece of cloth
lighting, soaked in kerosene oil.
Sqm
415
Cum.
33
Cum.
197
Cum.
556
Beams, Plinth beams, griders, bressumers, contilevers, Suspended floors lintels roofs and staircases
including spiral staircases, shelves etc.
Cum.
1842
Cum.
2425
Cum.
170
Providing and laying cement concrete internal walls, return walls, walls (any thickness) including
attached Plasters, Colume, Piers, Abutments, Pilars, Post, Structs, buttresses, string or lacing courses,
parapets coping, bedblocks, anchor blocking, plin window sills, fills etc. up to floor five level excluding
the cast of centring shuttering and finishing 1:11/2:3 ( 1 : Cement : 1 1/2 Coarse Sand : 3 grades tone
aggregate 20,, nominal size.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (PartI)
Providing and laying in position machine batched, machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced cement concrete structural elements, excluding the
cost of centring, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (PartI)
Add or deduct for providing richer or leaner mixer respectively at all floor levels.
Providing M-25 grade R.C.C. instead of M-20 grade R.C.C.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (PartI)
20
167
Page 3
21
Centring and shuttering including strutting, propping etc. And removal of form for.
Foundations, footings, bases of columns etc. for mass concrete.
Sqm
702
Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.
Sqm
2047
Sqm
4392
Sqm
262
Sqm
4046
Sqm
5865
Sqm
1688
Sqm
50
Sqm
12
22
Vertical and Horizontal lines fins individually or framing box louverd Band, faces and Eaves Board.
Sqm
53
23
Small lintels not exceeding 1.5m clear span, mouldings as in cornices, window sills, string, courses,
bands, copings, bed plates, anchor blocks and the like.
Sqm
164
Slab
Beam
Column
Sqm
Sqm
Sqm
800
640
870
Mtr.
1224
26
Sqm
220
27
Add or deduct for plaster drip course /groove in plastered surface or moulding to R.C.C. projections.
Mtr.
68
Sqm
3730
24
25
28
Extra for Shuttering in circular work (20% of respective catering and shuttering items)
Extra for additional height in centring, shuttering where requirement with adequate bracing propping
etc. including cast of de-shutter and de-centring at all levels, over a height of 3.5m for every additional
height of 1 metre or part thereof suspended floor, roof landing beams and balconies (plain area to be
measured).
Page 4
29
Providing, precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 6mm
nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and
finishing in cement mortar 1:3 (1 cement : 3 fine sand ) etc. complete excluding plastering of the
jambs, sills and soffits.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
50 mm thick
30
Sqm
52
Kg.
Kg.
181380
Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding
all complete.
Thermo -Mechanically treated Bar TMT FE-500 (For Conference cum welfare centre+UGT)
Thermo -Mechanically Treated bars(TMTC-500)8 mm dia bars(Other than Conference cum
welfare centre)
Thermo -Mechanically Treated bars(TMTC-500)10 mm dia bars(Other than Conference cum
welfare centre)
Thermo -Mechanically treated Bar TMT FE-500 12 to 32 mm(Other than Conference cum welfare
centre)
111775
Kg.
100mLx1c
m
Wx1cmD
25
Providing and filling in position bitumen mix filler of Proportion 80 kg of hot bitumen, 1 kg of cement 100mLx1c
m
and 0.25 cubic metre of coarse sand for expansion joints
Wx1cmD
Providing and fixing in position copper plate as per design for expansion joints.
32
34
35
30235
Kg.
31
33
55090
Kg.
Providing and fixing in position 12 mm thick bitumen imregnated fibre board conforming to IS: 1838
including cost of primer, sealing compound in expansion joints.
100mLx1
cmD
Mtr.
Mtr.
Providing and fixing sheet covering over expansion joints with iron screws as per design to match the
colour/shade of wall treatment.
Asbestos sheet 6 mm thick
150 mm wide
200 mm wide
Page 5
36
150 mm wide.
Mtr.
200 mm wide
Mtr.
Cum.
2527
Cum.
1985
Sqm
1175
Sqm
1175
Sqm
1175
Area of each slab over 0.2 sqm but upto 0.5 sqm Rajnagar plain white.
Sqm
Area of each slab over 0.2 sqm but upto 0.5 sqm Granite of any colour and shade
Sqm
3554
Marble work
Mtr.
Granite work
Mtr.
466
37
Extra for Brick work in superstructure above plinth level upto floor V level.
38
Half brick masonry with bricks of class designation 100 A in foundations and plinth in :
Cement mortar 1:4 (1 cement : 4 coarse sand).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Extra for half Brick masonry in superstructure above plinth level upto floor V level
39
40
41
Extra for providing and placing in portion 2 Nos. 6mm dia M.S bars at every third course of half brick
masonary.
SUB HEAD : IV : MARBLE WORK
Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters
facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick
base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixe with
matching pigament-epoxy touch ups including rubbing, curing etc. complete at all levels.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. over item no. 8.2
including machine polishing to edge to give high gloss finish etc. complete as per design approved by
Engineer-in-charge.
Page 6
42
43
44
45
46
Extra for fixing marble/granite stone over and above corresponding basic item, in facia and drops of
width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc.
complete.
Mtr.
146
Extra for providing opening of required size & shape for wash basins/kitchen sink in Kitchen platform.
Vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc.
including rubing and polishing of cut edges etc.complete.
Each
67
Sqm
White Marble - Raj Nagar Plain , Udaipur Green Marble / Zebra Black Marble - area of each slab over
upto 0.50 sqm.
Sqm
102
Providing and fixing expansion hold fastners on CC / RCC / Brick Surface backing including drilling
necessary holes and the cost of bolts etc complete.
Fastner with threaded dia 12mm
Each
120
Mirror polishing on marble work/stone work where ever required to given high gloss finish complete.
Marble work gang saw cut (Polished and machine cut) of thickness 18 mm for wall lining (Veener
work) in cement mortor 1:3 (1 Cement : 3 Coarse sand) including pointing with white cement motor 1:2
(1 White cement : 2 Marble Dust) with and mixture of pigment to match the marble shade (To be
secural to the backing of means of cramps, which shall be paid for seperating) Note:- Used PPC
Cement to be used conforming to IS: 1489 (Part-I)
Providing and fixing stone jaali 40 mm thick throughout (without sunking or moulding in jali slab ) in
cement mortar 1:3 (1 cement : 3 coarse sand ) includng pointing in white cement mortar 1:2 (1 white
cement : 2 stone dust) with an admixture of pigment , matching the stone shade , jali slab without any
chamfers etc.
47
48
49
Sqm
5.76
Cum.
Sqm
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory
windows including black enamelled M.S. but hinges with necessary screws excluding. Panelling which
will be paid for separately.
35 mm thick Second Class teakwood
Page 7
50
Providing and fixing panelling or panelling and glazing in panelled of panelled and glazed shutters for
doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside
grooves or rebates to be measured) panelling for panelled or panelled and glazed shutters 25mm to
40mm thick.
Second class teak wood
Sqm
Sqm
465
Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of
shutters (over all area of door shutter to be measured).
Sqm
455
53
Extra for cutting rebate in flush door shutters (total area of the shutter to be measured).
Sqm
112
54
Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average
width of aperture 1.4mm with wire of dia. 0.63 mm for doors windows and clerestory windows
including bright finished or/and black enamelled M.S. Butt Hinges with necessary screws.
Second class teak wood.
Sqm
22
Extra for Providing and Fixing Flush Door Shutter 1mm thick laminate of approved shade - Both side
of shutter.
Sqm
463
Sqm
Kg.
1308
Sqm
51
52
55
56
Providing and fixing flush door shutters non decorative type, core of block board construction with
frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands
and face veneers on both faces of shutters:
Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg/square
meter (4 mm thick) glass panels including black enamelled M.S. Butt hinges with necessary screws.
35 mm thick Second class teak wood.
57
58
Providing and fixing M.S. Grills of requirement pattern in frames of window etc. with M.S. flats square
or round bars etc. all complete.
Fixed to steel window by welding.
Providing and fixing fly proof galvanised M.S. wire gauze to windows and clerestory window using
galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia.
0.63 mm.
With second class teak wood beading 62x19 mm
Page 8
59
60
Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts,
nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix (1cement : 3
coarse sand : 6 graded stone aggregate 20mm nominal size). Note:- Used PPC Cement to be used
conforming to IS: 1489 (Part-I)
Each
150
Each
213
Each
Each
Each
236
138
44
Each
1215
Providing and fixing aluminium handles anodised (anodic coating not less than grade AC 10 as per IS:
1868) transparent or dyed to required colour and shade with, nuts and screws etc. complete.
125 mm
Each
251
100 mm
Each
236
Providing and fixing aluminium hanging floor door stopper anodised (anodic coating not less than
grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with, necessary screws
etc. complete.
Single rubber stopper
Each
Each
228
Sqm
Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than
grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with, nuts and screws
etc. complete.
250x16 mm
61
Providing and fixing aluminium tower bolts anodised (anodic coating not less than grade AC 10 as per
IS: 1868) transparent or dyed to required colour and shade with, nuts and screws etc. complete.
300x10 mm
150x10 mm
100x10 mm
62
63
64
65
Providing and fixing aluminium pull bolt lock anodised (anodic coating not less than grade AC 10 as
per IS: 1868) transparent or dyed to required colour and shade with, nuts and screws etc. complete.
Deduct if fixed shutters (without hinges) are provided instead of openable shutters for doors, windows
or cleresory windows with:
Black enamelled M.S Butt hinges with necessary screws.
Page 9
66
Extra for Providing and fixing flush door with teak veneering.
On one side
Sqm
174
Sqm
191
Sqm.
80
Each
Exceeding 10.00 sqm and upto 16.80 sqm in area (say average 14 sqm)
Sqm.
80
70
Sqm.
63
71
Providing and fixing T-iron frames for doors windows and ventilators of mils steel Tee-Sections, joints
miltred and welded with 15x3 mm lugs 10 cm long embedded in cement concrete blocks 15x10x10 cm
of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden
plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required
including.
Kg.
5687
67
68
69
Supplying and fixing rolling shutters of approved make, made of required size of M.S laths interlocked
together through their entire length and jointed together at the end by end locks mounted on specially
designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with
push and pull operation complete including the cost of providing an fixing necessary 27.5 cm long wire
springs grade No. 2 and M.S top cover of required thickness for rolling shutters.
Extra for providing mechanical device chain and crank operation for operating rolling shutters.
Page 10
72
73
Providing and fixing pressed steel door conforming IS code 351 manufactured from commercial mild
steel sheet of 1.25mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold
of mild steel angle of section 50x25 mm or base ties of 1.25mm pressed mild steel welded or rigidy
fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt
hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying
a coat of approved steel primer after pre-teatement of the surface as directed by Engineer-in-charge
Profile B
Mtr.
Profile C
Mtr.
1462
Profile E
Mtr.
140
Kg.
510
Sqm.
211
Sqm.
Sqm.
13
196
Kg.
88630
Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including
applying a priming coat of approved steel primer.
E.R.W. tube 40 mm nominal dia
73-A Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks
15x10x10 cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or
with woodenplugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as
required, including providng and fixing of glass panes with glazing clips and special metal-sash putty of
approved make complete including applying a priming coat of approved steel primer; excluding the
cost of metal beading and other fitting except necessary hinges or pivots as required. Note:- Used PPC
Cement to be used conforming to IS: 1489 (Part-I)
Doors
73-B Extra for providing and fixing steel beading of approved shape and section with screws instread of
glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units.
Steel Doors
Steel Windows
74
Structural Steel work riveted or bolted in rolled section, builtup sections, plate and inserts, trussess
and frame work, including cutting, hoisting, fixing in position and applying a prime coat of approved
steel primer etc. all complete.
Page 11
76
80
Fencing with welded steel wire fabric 75 mm x 50 mm providing 1.2M high fencing with Angle Iron
post 50m x 50m x 6mm at 3 meter centre to centre with 0.4m embedded in M-15 Grade cement
concrete, corner end and every 10th Post to be strutted, provided with welded steel wire fabric of 75 x
50 mm or 75 x 25 mm mesh and fixed to ironpost by flat iron 50 x 5mm and bolted etc all complete.
83
Sqm.
1605
Sqm.
232
Sqm.
1050
Sqm.
890
Cement plaster skirting (upto 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished
with a floating coat of neat cement.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
18 mm thick
82
82
81
Mt.
Providing and laying Ist quality Ceramic glazed wall tiles confirming to IS : 15622 (thickness to be
specified by manufacturer) of approved make in all colours, shades except burgundy, bottle green ,
black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm
thick bed of Cement Mortar 1:3 (1 Cement : 3 Coarse sand ) and jointing with grey cement slurry @
3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 15622 of approved make in colours such as white, ivory,
Grey, Fume Red, Brown, laid on 20 mm thick Cement motar 1:4 ( 1 cement : 4 coarse sand) including
pointing the joints with white cement and matching pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Page 12
84
85
Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 15622 of approved make in colours such shades except
white, ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cement motar 1:4 ( 1 cement : 4 coarse
sand) including pointing the joints with white cement and matching pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm.
Mtr.
1150
Sqm.
1196
Sqm.
918
Sqm.
374
Rajnagar plain white marble 18mm thick above 0.10 sqm upto 0.20 sqm.
Sqm.
30
Sqm.
32
86
87
88
Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or
equivalent make in colours such as white, ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cement
motar 1:4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching
pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or
equivalent make in colours such as white, ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cement
motar 1:4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching
pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Providing and laying vitrifed floor tiles skirting (thickness to be specified by the manufacturer) with
water absorption's less than 0.08% and conforming to IS: 15622 of approved make in all colours and
shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints
with white cement and matching pigments etc, complete. (Flooring and Skirting)
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Size of Tile 60x60 cm
89
Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineerin-charge) over 20 mm (average) thick base of Cement motar 1:4 ( 1 cement : 4 coarse sand) laid and
jointed with grey cement slurry including rubbing and polishing complete with.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Page 13
90
Tile work in skirting, risers of steps and dado over 12 mm thick bed of cement mortar 1:3 (1 cement : 3
coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement
mixed with pigment of matching shade complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Marble tiles (polished) Raj Nagar 8 mm thick
91
92
Sqm.
25mm thick.
Sqm.
830
Kota stone slab 25mm thick in riser of steps, skirting, dado and pillars laid on 12mm (Av.) thick cement
mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match
the shade of the slab including rubbing and polishing complete
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm.
422
Mtr.
25
Sqm.
615
Mtr.
740
Sqm.
484
Rmt.
671
Each
57
Kota stone slab flooring over 20 mm (Av.) thick base laid over and jointed with grey cement slurry
mixed with pigment to match the shade of the slab including rubbing and polishing complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
93
94
Extra for Marble stone flooring in treads of steps. Not Exceeding 30 cm in width.
95
96
Extra for kota stone floooring in steps and trades not exceeding 30 cm in width.
99
100
SUB-HEAD : IX : FINISHING
Page 14
101
102
103
104
105
106
107
108
109
Sqm.
4334
Sqm.
4505
Sqm.
6330
Sqm.
5520
Sqm.
5420
New work (two or more coats) over and incluidng priming coat with cement primer.
Sqm.
435
Distemperig with 1st quality washable distemper (ready made) of approved manufacturer and of
required shade and colour complete. As per manufacture's specifications.
Two or more coats on new work.
Sqm.
735
Applying one coat of cement primer of approved brand and manufacture on wall surface.
Cement Primer
Sqm.
830
Distemper Primer
Sqm.
735
Sqm.
780
Finishing walls with water proofing cement paint of approved brand and manufacture and of required
shade to give an even shade.
New work (three or more coats)
110
Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:
Page 15
Sqm.
300
114
Painting with synthetic enamel paint of approved brand and manufacture of required colour to given an
even shade:
115
Two or more coats on new work over an under coat of suitable shade with ordinary pain of approved
brand and manufacture.
Sqm.
7161
116
French Sprit Polishing two or more coats on wood work including a coat of wood filler.
Sqm.
460
119
Tiles brick masonry work 5 cm thick with the bricks of class designation 100 A in cement mortor 1:3 (
1 cement : 3 coarse sand) in superstructure.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm.
45
Pointing on tile brick work with cement mortor 1: 3 (1 cement : 3 coarse sand ) Flush Pointing.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm.
135
Kg.
3490
Each
263
120
122
124
125
Providing and fixing stainless steel (SS 304 Grade) adjustable friction window stays of approved
quality with necessary stainless Steel Screws etc. to the side hung window as per diection of Engineerin-Charge-355x19mm.
Providing and fixing 12 mm thick prelaminated three layermedium density (exterior grade) particle
board Grade I, Type II conforming to IS:12823 bonded with phenol formaidhyde synthetic resin, of
approved brand and manufacture in panelling fixed in aluminium doors, window shutters and partition
frames, with C.P. brass/stainless steel screws etc. complete as per architectural drawings and direction
of engineer-in-charge.
Page 16
Pre-laminated particle board with decorative lamination on one side and balancing lamination of
Sqm.
25
127
130
Sqm.
155
0
With glass panes of 4.0 mm thickness (weight not less than 10.0kg/sqm.)
Sqm.
With glass panes of 5.50 mm thickness (weight not less than 13.75kg/sqm.)
Sqm.
595
Providing and fixing double action hydraulic floor spring of approved brand and manufacture
(conforming to IS:6315), for Aluminium doors including cost of cutting floor as required, embedding in
floors and cover plates etc. complete as per direction of Engineer-in-Charge.
Each
25
Sqm.
3115
meter
meter
70
150
Providing and fixing glazing in aluminium door, window, ventilator, shutters and partitions etc. with
PVC/Neo Prene gasket etc. complete as per the architectural drawings and the directions of Engineerin-Charge. (Cost of aluminium snap beading shall be paid in basic item)
With average thickness of 120mm and minimum thickness at khurras as 65mm. Note:- Used PPC
Cement to be used conforming to IS: 1489 (Part-I)
135
Page 17
136
137
Extra over item no. 1 for boring, providing and installing cast in situ double under reamed piles, instead
of single under ream of specified diameter and length. (Only the quantity of extra bulbs are to be paid).
90
per test
per test
2
10
Vertical load testing of pile in accordance with IS:2911 (Part-IV) including installation of loading
platform and preparation of pile head or construction of test cap and dismantling of test cap after test
etc. complete as per specification & the direction of Engineer-in-Charge.
Single Pile
Upto 50 tonne capacity pile cost per test
Above 50 tonne & upto 100 tonne capacity pile
138
Each
Cyclic vertical load testing of pile in accordance with IS Code of practice IS : 2911 (Part-IV) including
preparation of pile head etc. for :-
Page 18
Single pile
Upto 50 tonne capacity pile
Group of two pile
Upto 50 tonne capacity each
139
140
per test
per test
10
per test
Kg
125100
Cum
60
Cum.
670
Centring and shuttering including strutting, propping etc. And removal of form for.
Foundations, footings, bases of columns etc. for mass concrete.
Sqm
850
Sqm
485
Cum.
670
Lateral load testing of single pile in accordance with I.S. Code of practice I.S. : 2911 (Part-IV) for
determining safe allowable lateral load on pile :
Upto 50 tonne capacity pile
Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding
etc. all complete.
Thermo-mechanically treated bar TMT FE-415
141
142
Demolishing RCC work including stacking of steel bars and disposal of unserviceable material with 50
meter lead.
Providing and laying in position machine batched, machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced cement concrete structural elements, excluding the
cost of centring, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (PartI)
All work upto plinth level
143
144
145
A
B
C
D
Add or deduct for providing richer or leaner mixer respectively at all floor levels.
Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. (Note:- Ready Mix Concrete (RMC)
using PPC Cement to be used confirming to IS : 1489 (Part-I)
Building Carriage
Bricks
Aggregate
Coarse Sand
Local Sand
Total
1000nos.
Cum
Cum
Cum
1321
4068
2916
3348
Page 19
Qty
Rate
Unit
Cum
435
Cum
474.86
Sqm
606
Amount
Brick edging 7 cm width 11.4 cm deep to plinth protection with bricks of class
designation 75 including grouting with cement mortor 1 : 4 ( 1: Cement : 4 Fine sand)
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Unit
Qty
Rate
Meter
959
Each
97
Kg.
220
Sqm
265
Amount
Unit
Qty
Rate
10
11
SUB-HEAD : IX : FINISHING
Finishing wall with Premium Acrylic smooth exterior paint with silicon additions of
required shade. New work (Two or more coats applied @ 1.43 Ltr / 10 sqm over and
include base coat of water proofing cement paint applied @ 2.20 kg/10sqm.
Melamine Polishing on wood work (one or more coat)
Sqm.
Sqm.
7085
275
Kg.
790
Filling the gap in between aluminium frame and adjusment RCC/Brick/ Stone work by
Providing weather silicon sealed over backer rod of approved quality as per Architectural
drawing and direction of Engineer-in-Charge.
Upto 5mm depth and 5 mm width.
Rmt
430
Providing and fixing Double glazed hermetically sealed glazed in Aluminium window,
ventilator and portation etc. with 6 mm thick clear float glass both side having 12 mm air
gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealent
(Both Primary and Secondary sealent) etc as per specifications, drawings and direction of
Engineer-in-Charge complete.
Sqm.
Amount
Unit
Qty
Sqm
70
Rm
158
Providing and erecting 2mm thick profiled metal sheets from approved manufacturer
including securing firmly by fastening with substrate to receive concrete (concrete to be paid
separately) complete as per manufacturer's specifications and as directed (Plan area to be
measured, for payment) rates to include two or more coats of synthetic enamel paint over a
coat of zinc chromate steel primer on the exposed sides of sheeting etc. all complete at all
height and depth.
Sqm.
23
Rate
Amount
Qty
Sqm
1260
Sqm.
185
Sqm.
140
Supply & installation of TATA Blue Scope or approved equivalent make Double skin
insulated Roofing / cladding system comprising of HI-RIB profiled Factory finished
External and internal sheets manufactured out of 0.5mm TCT (Total coated thickness)
silicone modified polyster (SMP) coated Hi-Tensil Galvolume Steel (AZ-150 GSM
Zinc/Aluminium alloy coating total of both sides as per AS 1397) having 550Mpa Yield
strenght. The weathering surface to be Given a finish coat nominal 5 micron. The sheets
shall have 1000 mm cover width, 28mm high crests at 250 mm wide pan with special
Male/Female side laps and anti-siphoning feature to prevent leakges. The pan shall be
stiffenered by using 3 small ribs. The inner sheet shall be RMP coated galvanised steel
(Z180 GSM zinc coating/275 Mpa Steel) in similar dimenions/size and fixed to the structure
(by others) by means oif corrosion protecitons self drilling sefl tapping fasteners. The Subgirts of size 50mm x 50mm x manufactured out of 1.6 G.I.. G.I "Z" shape would be fixed
with similar scres (12-14x15) on to surface.
All insulation of 50 mm thick glasswool of density 24 Kgs wrapped in clear polythene
sheets shall be fixed in the cavity between two sheets. The sheets shall be supplied in custom
lengths and for a maximum up to 12 mts.
Unit
Providing and fixing 50 x 50 mm thick of glass mosaic tile in all the shape and size thickness
as per manufacturer specification at all depth and height of approved colour and shade over a
bed of cement mortar 1:2 (1 cement : 2 coarse sand) jointed with white cement slurry mixed
with pigment to match the sahde of glass mosaic tile or fixed with chemical adhesive as per
recommendation by Manufacturer. All work to be carried out as per drawing.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Rate
Amount
Qty
Sqm.
3850
Sqm.
4525
Sqm.
2025
Sqm.
100
Sqm.
68
Sqm
180
Providing and applying two or more of water base enamel paint to all internal area with base
coat at all height and depth etc all complete as per the direction Engineer-in-Charge. (water
base enamal paint to meet low VOC criteria as specified by GRIHA)(For CCWC)
Providing and applying two or more of water base enamel paint to all internal area with base
coat at all height and depth etc all complete as per the direction Engineer-in-Charge. (water
base enamal paint to meet low VOC criteria as specified by GRIHA)(All buildings
except CCWC)
Providing and applying external paint of approved brand and manufacture equvalent to M/s
SKK make at all height & depth etc all complete as directed by Engineer-in-Charge (Basic
coat of Rs. 25/- sft included base coat)
10
25 mm cement plaster in cement mortor 1:4 (1 Cement : 4 coarse sand) including Providing
Chicken mess etc all complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
11
Unit
Providing and applying two or more coats of colour less silicon paint at all Locations
Prepared and applied as manufacture specifications Including appropriate Prime coat,
preparation of surface etc. all complete as directed by Engineer-in-Charge.
12
Rate
Amount
14
Unit
Qty
Sqm
138
R.M.
161
Providing and laying polymer modified concrete screed 25mm thick using 8mm down
aggregate in 1:1:3 (1 cement:1 aggregate:3 coarse sand admixed with special
DICHATMENT DM-0.5% by weight of cement, NAFUFIL SBR-5% by weight of cement)
complete manufactured by M.C. Bauchemie or approved equivalent as per Architect's
direction. Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Providing and laying MECEKRETE or approved equivalent non shrink grout of size
30x30mm complete
Note:
All additional openings made in and around RCC slab for sanitary pipes shall have to be
sealed, grouted and made water tight before commencing on the above works and above
treatment shall be carried out through a specialized approved agency.
15
Providing and applying 50mm thick polyurethane rigid foam sprayed in situ by automatically
and mechanised system with density of 40 Kgs./Cum. Using approved raw material
conforming to manufactured by BASF. ICI, BYER the international standard specification
over terrace including making groove 30mmx15mm in 3 m x 3m grids. (This work is to be
carried out through approved speciaslised sub-contractors experienced in polyurethane
insulation work with the approval of the consultant and shall be guaranteed fully effective
for a period of ten years. Nothwithstanding this, the responsibility of the effectiveness of the
treatment shall be fully, entirely and unqualifiedly be that of the main contractor for the
work.)
Sqm
1375
20 mm thick plaster (1:4) in 3 layers (details may be obtained from Consultant / Client on
chemical injection waterproofing).
Sqm.
1302
Grouting with 25mm dia G.I. nozzles (Details may be obtained from Consultant / Client on
chemical injection waterproofing).
Sqm.
1412
Sqm.
385
On wall surfaces (actual treated area to be measured for payment in the following manner).
20mm thick cement mortar (1:4) with polymer based waterproofing compound plaster with
checken wire mesh (Details may be obtained from Consultant / Client on chemical injection
waterproofing).
Rate
Amount
16
Unit
Qty
Sqm.
Providing and laying waterproofing of basement with chemical injection method from
approved specialised firm all as per specifications carrying 10 years guarantee. (Tenderer
should submit the name of the specialist).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Basement floor (Actual treated area to be measured for payment in the following manner):
20 mm thick plaster (1:4) in 2 layers (details may be obtained from Consultant / Client on
chemical injection waterproofing).
Sqm.
580
Sqm.
440
20mm thick cement mortar (1:4) with polymer based waterproofing compound plaster with
checken wire mesh (Details may be obtained from Consultant / Client on chemical injection
waterproofing).
Sqm.
630
Grouting with 25mm dia G.I. nozzles (Details may be obtained from Consultant / Client on
chemical injection waterproofing).
Sqm.
630
Providing and fixing G.I. Vent Pipe as per approved design or as directed by Engineer-inCharge
100 mm dia
65 mm dia
Meter
Meter
8
8
0
Each
Each
Each
Each
Each
Each
4
4
8
8
12
4
Grouting with 25mm G.P. Nozzles detailed may be obtained from consultant / client on
chemical injection water proofing.
On wall surfaces (actual treated area to be measured for payment in the following manner).
17
18
Providing, installation 6mm thick M.S. Puddle flange including welding with M.S. Pipe as
150 mm dia
100 mm dia
80 mm dia
65 mm dia
50 mm dia
40 mm dia
Rate
Amount
19
20
Unit
Qty
32 mm dia
25 mm dia
Each
Each
4
8
Providing and fixing 560 mm dia C.I. Manhole cover with frame (heavy duty) total weight of
cover and frame hot less than 208 Kgs (Weight of cover 108 Kgs and weight of frame 100
Kgs.)
Each
10
Sqm.
480
Providing and laying waterproofing treatment for Car park, Podium and gardens over
basement roof slab, all as per following specification carrying 10 years; guarantee; (Tenderer
should submit the name of specialist)
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Polymer modified cementeclous slurry coating of DICHTAMENT D5 + NAFUFILL BB1.
21
Polymer modified concrete screed 25mm thick using 8mm down aggregates (1:1:3) 1
cement : 1 aggregate : 3 coarse sand admixed with special dischatament DM .0.5% by
weight of cement Nafufill SBR 5% by weight of cement manufactured by MC Bauchemie (I)
Pvt. Ltd.
22
All upstand masonary work with 20mm thick waterproof plaster (CM) 1 : 4 (1 cement : 4
coarse sand) admixed with DOCHTAMENT DM @ 200ml. Per bag of cement)
All corner junctions with EMCERCITE mortar (30x30)
23
Water proof screed or coba in proper slope using admixed with DICHTAMENT Dm 100
thick (Av.)
Final coating of DICHTAMENT DA + NBB2
Note:- The treatment is to be carried out by a specialised agency with the approval of the
Engineer-In-Charge. The specialised agency should furnish the guarantee in the named
owner for a period of 10 years. Not with standing this, the responsebility of the effectiveness
of the treatment shall be entirely and unqualified be that of the main contractor for the work.
The tenderer to state the name of specialised firm.
Rate
Amount
Unit
Qty
Rate
Amount
Description
SUB HEAD : 1 WATER SUPPLY
Unit
Qty
Providing and fixing G.I. Pipes complete with G.I. Fitting, Clamps,
including cutting, making the good wall. (Exposed on walls shafts and
terrace)
15 mm dia nominal bore
Meter
58.00
Meter
96.00
Meter
134.00
Meter
61.00
Meter
79.00
Meter
27.00
Meter
206.00
Meter
247.00
Meter
181.00
Meter
0.00
Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc. (external work)
25 mm dia nominal bore
Meter
91.00
Meter
42.00
Rate
Amount
10
11
14.00
Each
63.00
Each
82.00
Providing and fixing gate valve with C.I. wheel of approved quality
(screwed end).
32 mm dia nominal bore
Each
11.00
Each
8.00
Providing and fixing brass ferrule with C.I. mouth cover including
boring and tapping the main.
25 mm dia nominal bore
Each
11.00
Each
57.00
Each
11.00
Each
47.00
12
20 mm diameter pipe
Each
57.00
25 mm diameter pipe
Each
107.00
32 mm diameter pipe
Each
36.00
40 mm diameter pipe
Each
76.00
50 mm diameter pipe
Each
5.00
Each
74.00
13
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank of approved brand and manufacture with cover and suitable
locking arrangement and making necessary holes for inlet, outlet and
overflow pipes but without fittings and the base support for tank.
Per Litre 50700.00
14
Providing and fixing C.P. brass long body, bib cock of approved quality
conforming to IS standards.
a) 15 mm nominal bore
Each
22.00
Providing and fixing C.P. brass angle valve for basin mixer and gyser
points of approved quality conforming to IS: 8931
a) 15 mm nominal bore
Each
197.00
15
Each
150.00
Each
54.00
Each
14.00
16
17
Providing and fixing white vitreous china pedistal type water closet
(European type W.C. Pan) with seat and lid C.P. brass hinges and rubber
buffers, 10 litre low level P.V.C. flushing cistern with fittings. C.I. /
M.S. brackets 40mm diameter flush bend with fittings and clamps,
overflow arrangement with specials and mosquito proof coupling of
approved municipal design complete including painting of fittings and
brackets, cutting and making good the walls and floors wherever
required.
W.C. pan with white solid plastic seat and lid.
Providing and fixing white vitreous china water closet squatting pan
(Indian type W.C. Pan) with 100 mm sand cast iron P or S trap.10 Litre
low level P.V.C. flushing cistern (of approved make) with fittings. C.I.
M.S. brackets, 32 mm diameter flush pipe with fittings and clamps,
overflow arrangement with specials and mosquito proof coupling of
approved municipal design including painting of fittings and brackets,
cutting and making good the walls and floors wherever required.
Long pan pattern W.C. pan of size 580 mm with flush pipe & overflow
arrangement.
18
Providing and fixing white vitreous china flat back or wall corner
typelipped urinal basin of 430x260x350 mm sizes respectively with
automatic flushing cistern with C.I./M.S. brackets standard size of G.I.
flush pipe and C.P. brass spreaders with brass unions and G.I. clamps
complete, including painting of fittings and brackets, cutting and making
good the walls and floors wherever required.
One urinal basin with 5 litre P.V.C. automatic flushing cistern.
19
20
21
23
Each
12.00
Providing and fixing C.P. brass waste for sink or wash basin.
32 mm dia
40 mm dia
Each
Each
0.00
90.00
16.00
Providing and fixing PVC waste pipe for sink or wash basin including
PVC waste fittings complete.
Flexible Pipe
32 mm dia
40 mm dia
Each
Each
74.00
9.00
Providing and fixing 100 mm sand cast Iron grating for gully, floor or
nahani trap.
Each
106.00
Each
42.00
Each
74.00
Providing and fixing stainless steel jali (grating) with or without hole for
waste pipe for floor / nahani trap.
75 mm dia weight not less than 70 gms
24
25
26
Each
63.00
Meter
426.00
Meter
138.00
Each
Each
95.00
57.00
Each
89.00
Each
30.00
Each
12.00
75 x 75 x 75 x 75 mm
Sand cast iron S&S
Each
1.00
Each
12.00
28
29
30
75 x 75 x 75 x 75 mm
31
32
33
34
35
Each
1.00
Providing and fixing single equal plain junction of required degree with
access door, insertion rubber washer 3 mm thick bolts and nuts
complete.
100 x 100 x 100 mm
Sand cast iron S&S
Each
12.00
75 x 75 x 75 mm
Sand cast iron S&S
Each
1.00
100 x 100 x 75 x 75 mm
Sand cast iron S&S
Each
9.00
Providing lead caulked joints to sand cast iron/ centrifugally cast (spun)
iron pipes and fittings of diameter.
100 mm
75 mm
Each
Each
156.00
61.00
Providing and fixing M.S stays and clamps for sand cast iron /
centrifugally cast (spun) iron pipes of diameter.
100 mm
75 mm
Each
Each
96.00
58.00
Providing and fixing sand cast iron trap of self cleaning design with sand
cast iron screwed down or hinged grating with or without vent arm
complete, including cost of cutting and making good the walls and
floors.
100 mm inlet and 100 mm outlet
100 mm inlet and 75 mm outlet
Each
Each
38.00
46.00
36
Cutting chases in brick masonry walls for following diameter sand cast
iron / centrifugally cast (spun) iron pipes and making good the same
with cement concrete 1:3:6 (1 cement : 3 coarse sand and 6 graded stone
aggregate 12.5mm nominal size) including necessary plaster in cement
mortar 1:4 (1 cement : 4 coarse sand)
100 mm
75 mm
37
30.00
13.00
Meter
Meter
40.00
230.00
Each
29.00
Each
Each
17.00
19.00
38
Meter
Meter
Plumbing 1B
Sl.
No.
Description
Unit
Qty
Each
19
Each
19
Each
20
Each
69
Providing and fixing towel rail complete with brackets fixed to wooden cleats with C.P.
brass screws.
Each
TOTAL
68
Providing and fixing 600 x 120 x 5 mm glass shelf with edges rounded off supported on
anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed
with 40 mm long screws, rawl plugs etc. complete.
Rate
Amount
Plumbing 1C
Sl.
No.
Description
Unit
Qty
Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall.
Metre
34.00
Each
78.00
Each
73.00
Each
72.00
Providing and fixing inlets fitting with max. 3 inlets 32, 40 or 50mm size
fabricated from 100mm dia pipes and fixed to CI trap and set in 1:2:4 cement
concrete as per standard drawing complete.
Providing and fixing white vitreous china flat back half stall urinal of
580x380x350mm with fully automatic battery operated, photo electric cell type
flushing system comprising of solenoid valve, concealed copper piping, wiring
& sensor complete in fully operating condition including standard size C.P.
brass flush pipe, spreader with union, CP clamps and screws, CP flanges, waste
fitting as per IS : 2556 and CP bottle trap, complete including cutting &
making good the walls and floor wherever required
Providig and Fixing white vitreous china oval wash basin of 560mm x 410mm
size with specially fabricated M.S. or CI brackets, 32mm CP brass waste of
standard pattern, 32mm dia C.P. brass bottle trap Piller taps and making
connection to the waste pipe in wall with C.P wall flange and rubber adopter
complete with required accessories including painting of brackets and cutting
and making good the walls wherever required.
Rate
Amount
Providing and fixing white vitreous china Kitchen sink with C.I. brackets, C.P.
brass chain with rubber plug 40 mm C.P.brass waste and 40 mm C.P. brass trap
with necessary C.P. brass unions complete including painting brackets, fittings,
cutting and making goog the wall wherever required.
Kitchen sink with drain board.
Size 510 x 1040 bowl depth 178 mm
Each
1.00
Each
82.00
Meter
Meter
60.00
56.00
Each
35.00
Providing and fixing floor clean out plug / clean out plug for cast iron soil or
waste pipes comprising of C.I. Plug, nipple, bend including lead jointing etc.
complete.
For 100 mm dia pipe
TOTAL
Sl.
No.
1
Description
Qty
Wiring for Light point / Fan point / Exhaust Fan point / Call Bell / 6 Amp light
plug point with 2x1.5 sq.mm PVC insulated stranded copper conductor cable
alongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing
in surface/recessed PVC conduit as required. (Point shall be controlled / looped
from existing point).
Point
Point
Point
0
0
489
Point
525
Point
10
Metre
3171
Wiring for twin control Light point with 1.5 sq.mm FR PVC insulated copper
conductor single core cable in surface / recessed PVC conduit, 2 way modular
switch, modular plate, suitable size GI box and earthing the point with 1.5
sq.mm FR PVC insulated copper conductor single core cable etc. as required.
Wiring for light / power plug point with 2 x 4 sq.mm FR PVC insulated copper
conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 4
sq.mm FR PVC insulated copper conductor single core cable for loop earthing as
required.
Rate
Amount
10
Wiring for light / power plug point with 4 x 4 sq.mm FR PVC insulated copper
conductor single core cable in surface / recessed PVC conduit alongwith 2 Nos.
4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing
as required.
Metre
1155
Each
144
Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess ,including providing and fixing 6 pin 20 / 16 amps
modular socket outlet and 15 / 16 amps modular switch, connection, painting
etc.as required.
Each
69
Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess, including providing and fixing 3 nos 3 pin 5 / 6 amps
modular socket outlet and 1 no 15 / 16 amps modular switch,connection,
painting etc.as required.
Each
40
Supplying and fixing 20 Amps, 240 Volts, SPN industerial type, Socket outlet,
with 2 pole and earth, metal enclosed plug top along with 20 amps, 2Pole,
RCCB in sheet steel enclosure, on surface or in recess with chained metalcover
for the socket out let and complete with connections, testing andcommissioning
etc. as required.
a) 20A, 3 pin socket outlet controlled by 20A 2P RCCB.
Each
11
Supplying and fixing 20 Amps, 240 Volts, SPN industerial type, Socket outlet,
with 2 pole and earth, metal enclosed plug top along with 20 amps, C series,
MCB in sheet steel enclosure, on surface or in recess with chained metalcover
for the socket out let and complete with connections, testing andcommissioning
etc. as required.
Each
10
Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess, including providing and fixing 3 pin 5 / 6 amps modular
socket outlet and 5 / 6 amps modular switch, connection, painting etc.as
required. (For light plugs to be used in non residential buildings.)
11
12
13
14
15
Metre
Metre
Metre
Metre
Metre
510
5860
1700
400
350
Metre
Metre
965
430
Wiring for group light point controlled from existing MCB in DB with 2x4
sq.mm PVC insulated stranded copper conductor single core cable in
surface/recessed PVC conduit alongwith 1 No. 4 sq.mm PVC copper conductor
cable for loop earthing as required (OUTDOOR RECESSED LIGHT).
Metre
240
Wiring for circuit / submain wiring along with earth wire with the following
sizes of FR PVC insulated copper conductor, single core cable in surface /
recessed PVC conduit as required.
2 X 1.5 sq.mm +1 X 1.5 sq.mm Earth wire
2 X 2.5 sq.mm +1 X 2.5 sq.mm Earth wire
2 x 10 sq.mm + 1 x 10 sq.mm earth wire
4 x 10 sq.mm + 2 x 10 sq.mm earth wire
4 x 16 sq.mm + 2 x 16 sq.mm earth wire
4 x 25 sq.mm + 2 x 16 sq.mm earth wire
Metre
Metre
Metre
Metre
Metre
Metre
0
1795
640
550
715
400
Each
18
16
Each
19
Metre
Metre
Metre
Metre
Metre
Metre
Metre
Metre
Metre
Metre
Metre
45
360
0
100
0
0
0
0
0
200
300
Set
Set
Set
4
6
0
Supplying and making cable end termination complete with brass compression
gland, crimping thimbles and insulating and PVC sheathed aluminium conductor
cable of1.1 KV grade of the under noted sizes as required.
a) 3.5 x 70 sq.mm
b) 3.5 x 50sq.mm
c) 3.5 x 35sq.mm
Set
Set
Set
Set
Set
Set
Set
Set
8
4
4
4
4
4
6
6
Set
Earthing with copper Earth plate 600 mm x 600 mm x 3.15mm thick including
accessories and providing masonary enclosure with cover plate having locking
arrangement and watering pipe etc. (but without charcoal or coke and salt)
complete as required.
Set
Set
Metre
Metre
Metre
285
220
80
Providing and fixing of lightning conductor finiel, made of 25mm dia 300mm
long GI tube, having single prong at top with 85mm dia 6mm thick GI base plate
including holes etc. complete as required.
Each
d) 4 x 25sq.mm
e) 3 x 25sq.mm
f) 3 x 16sq.mm
g) 3 x 10sq.mm
h) 4 x 6 sq.mm
i) 3 x 6sq.mm
j) 3 x 4sq.mm
k) 3 x 2.5sq.mm
Extra for using salt and coke for G.I or copper plate earth electrode as required.
9
10
11
Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall
for lightning conductor as required. (for horizontal run).
Metre
45
Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall
for lightning conductor as required (for vertical run).
Metre
25
Providing and fixing testing joint, made of 20mm x 3mm thick GI strip, 125mm
long with 4 nos. of GI bolts, nuts check nuts and spring washers etc. complete as
required.
Each
13
Metre
25
Set
Set
Description
Unit
Qty
a)
4 x 16 sq.mm
Meter
110
b)
4 x 10 sq.mm
Meter
c)
4 x 6 sq.mm
Meter
d)
3 x 6 sq.mm
Meter
e)
3 x 10 sq.mm
Meter
f)
3C x 1.5 sq.mm
Meter
100
g)
5C x 1.5 sq.mm
Meter
50
Supplying and fixing of CRCA sheet steel, perforated cable tray duly stove enamel
painted of approved shade in position including fixing in trench/along wall or ceiling
complete with M.S. rod/flat hangers directly grouted in walls/ceiling or welded with
steel structure etc. with necessary materials etc. as required.
Rate
Amount
R.M.
70
R.M.
200
R.M.
Metre
72
Providing and fixing 8 SWG G.I. wire on surface or in recess for loop earthing
alongwith the existing surface /recessed conduit/submain wiring/cable as required
Metre
Electrical 1C
Sl.
No.
1
Description
Unit
Qty
Each
22
Each
Each
Each
66
Each
26
Rate
Amount
10
11
Each
10
Each
Each
Each
13
Each
26
Each
Each
Each
Each
200
12
13
14
15
16
17
18
19
20
21
Each
Each
10
Each
140
Each
39
Each
12
Each
Each
44
Each
73
Each
Each
28
22
23
24
25
26
27
28
29
30
31
32
Each
20
Each
87
Each
Each
Each
25
Each
Each
Each
Each
16
Each
Each
142
33
34
35
36
37
38
light
The
hour
No.
Each
20
Each
a) 1200mm
b) 1400mm
Each
Each
63
42
Each
Each
33
4
Each
Each
39
40
41
42
43
44
45
Supply and fixing circular/ hexagonal M.S. sheet ceiling fan box with
clamp of internal dia 140mm, 73 mm height, 3mm thick rim top lid of
1.5mm thick M.S sheet lidss shall be screwed into M.S. box by means of
3mm round headed screws, clamps shall be made of 12 mm dia M.S bar
bent to be shape as per standard drawing with over all length as 80 cm
Each
38
Each
88
Each
62
Each
11
Each
Each
Each
46
47
48
49
50
51
52
Each
Each
Each
16
Each
Each
Each
Each
A. 8 WAY SP&N DB
i) 1 No. 40 Amps DP MCB+RCCB
ii) 4 Nos. 6-20 Amp SP MCB as outgoing
B. 12 WAY SP&N DB
i) 1 No. 40 Amps DP MCB+RCCB
ii) 8 Nos. 6-20 Amp SP MCB as outgoing
C. 4 WAY TP&N DB
i) 1 No. 40 Amps 4P MCB+RCCB
ii) 12 Nos. 6-20 Amp SP / 3 Nos TP MCB as outgoing
D. 8 WAY TP&N D.B
i) 1 No. 32 Amps 4 Pole MCB +RCCB
ii) 24 Nos. 6-32 Amps SP/ 6 Nos TP MCBs as outgoing
E. 12 WAY TP&N D.B.
i) 1 No. 63 Amps 4P MCB +RCCB
ii) 36 Nos. 6-20 AMPS SP/ 9 Nos TP MCB outgoing
Sub-Head : V
Nos.
Nos.
Nos.
Nos.
Nos.
Metre
175
a)
b)
c)
d)
4
Each
Each
Each
Each
Each
0
0
1
2
5
Providing, laying, connecting and testing of multi-core telephone unarmoured cable of conductor size 0.61 mm dia annealed copper conductor
PVC insulated PVC sheathed along with wall or ceiling or through existing
pipe etc as required.
a) 100 pair telephone cable
b) 50 pair telephone cable
c) 20 pair telephone cable
d) 10 pair telephone cable
Meter
Meter
Meter
Meter
0
0
50
115
Each
22
Each
Metre
Supplying, fixing of T.V. antennna socket outlet on the modular plate type
switch plate with zinc passivated box and along with modular base & cover
plate in recess as required.
Supplying and drawing of coaxial T.V cable RG-6 solid copper conductor
PE insulated, shielded with fine tinned copper braid and protected with
PVC sheath in the existing surface/recessed PVC conduit as required.
Supplying and fixing outlet box with locking arrangement of size 250 x
200 x 100 mm 16 gauge sheet steel in recessed as required.
Supplying and fixing of following splitter/tap off with suitable boxes as
required.
a) 4 way splitter
b) Tap off
Each
Each
Each
4
1
Nos.
Sub-head : XV - Lifts
2 Supplying at site, installation, testing and commissioning of 16 passenger
lifts (machine room less), speed 1.5 metre per second serving Ground to
Second Floor (3 landing and 3 stops) approx. 8.4metre travel, suitable for
operation on 415 volts, 3 phase, 50 cycles, A.C. electric power supply,
complete with contral panel, horizontal stainless steel sliding doors, all
safety devices including automatic resque devices, all fixtures with
stainless steel face plates/finishes, handrail on three sides etc. with interior
of car as per specification as approved by Owner / Architect complete in all
respects including supplying, laying and termination of copper signal
cable/communication cable of required size and core from supervisory
display panel located at a central place to each lift control room with
supply & fixing of supervisory display panel as per specification.
Total (in Rs).