Академический Документы
Профессиональный Документы
Культура Документы
Created by:
h5
Given:
f'c=
fy=
qa=
h1
h2
19
feet
2.5
feet
soil=
h1=
h2=
h3=
h4=
h5=
=
=
Surcharge=
Freeze depth=
Ca=
Cp=
h3
h4
3 ksi
60 ksi
4,000 psf
100
3
2
9
13
1
31
1
300
5
0.32
3.12
psf
feet
feet
feet
feet
feet
(friction coeff)
psf
feet (make sure you can meet this)
688 lb
H1=
7,398 lb
H2=
W=
X=
Lfooting=
2,065 lb
2,150
8.36 feet
12.55 feet
Moverturn=
75,216 ft lb
MH2=
22,195
Righting Moment
Force
Moment Arm
Moment
W 1=
4,687.5
* 6.3 ft
29,296.9 ft-lb
W 2=
712.5
* 2.8 ft
1,959.4 ft-lb
W 3=
2,850.0
* 3.5 ft
9,975.0 ft-lb
W 4=
Rv=
18,700.0
26,950.0
* 8.3 ft
=
MRighting =
154,275.0 ft-lb
195,506.3 ft-lb
David Taylor
UMKC SCE
Senior Design
(friction coeff)
4.46 ft
*Verify that it is in the middle third of footing
3 Stem Design
3.1 Design of stem for moment
Mu=
86.28 ft-k
=
MU
bd 2
482.6 psi
bd2= 2,383.80
*assume b= 12
h=
16.59 in
ROUND UP to next best number
h=
18 in
(d= 15.5 in)
Therefore,
MU
bd 2
=
As=
399.04
0.0073 *
* Find the equivalent from Table A.12 of Book "Design of Reinf. Concrete"
1.358 in2
=>
Use #8 @ 6"
(1.57 in^2)
0.0015 OKAY
0.45 in2
*Assume one third inside face and two-thirds are outside face.
USE #4 @ 7.5" outside face and #4 @ 15" inside face.
3.4 Checking Shear Stress in Stem
Vu= 12,163.76 lbs
Vc=
15,281.46 lbs
4 Footing Design
4.1 Design of Heel
*The upward soil pressure is conservatively neglected, and a load factor of 1.2 is used for calculating the shear and
moment because soil and concrete make up the load. Assume d = footing depth - 3.5"
Vu=
24735 lb
Vc=
26126.366 lb
MU
bd 2
=
105124 ft-lb
166
[min=0.0033]
0.00333 *
* Find the equilalent from Table A.12 of Book "Design of Reinf. Concrete"
Using ,
As=
1.06 in2/ft
=>
Use #9 @ 11"
d required calculated with ACI Equation 12-1 for #9 top bars with c=2.50 in. and K tr = 0 is 49 in. <
81 in. available.
Note: Temperature and shrinkage steel is normally considered unnecessary in the heel and toe.
However, #4 bars @ 18" in. O/C in the long direction are used to serve as spacers for the flexural
steel and to from mats out of the reinforcing.
4.2 Design of Toe
* For service loads, the soil pressures previously determined (in sect. 2.1) are multiplied by 1.6 by a load factor of 1.6
because they are primarily caused by lateral forces.
Vu=
1281.55
MU
bd 2
=
5598.157 =
6880 lb
6801 ft-lb
285.2
[min=0.0033]
0.00512 *
* Find the equilalent from Table A.12 of Book "Design of Reinf. Concrete"
Using ,
As=
1.63 in2/ft
=>
Use #9 @ 6"
d required calculated with ACI Equation 12-1 for #9 top bars with c=2.50 in. and K tr = 0 is 38 in. <
48 in. available.
Mu (ft-lb)
2987.589
16218.34
46094.23
86281.57
Effective
stem d
(in.)
11.08
12.66
14.24
15.50
Mu/bd2
24.34
101.22
227.42
359.13
0.0033
0.0033
0.00388
0.00648
As req'd
(in2/ft)
0.44
0.50
0.66
1.21
Bars
needed
#8@ 18"
#8 @ 18"
#8 @ 12"
#8 @ 6"