Академический Документы
Профессиональный Документы
Культура Документы
SDM is used for in-band management only. The IOS CLI can be used for in-band and
out-of-band management. \\\\\\\\\\\\\
SDM is accessed through a Telnet application. The IOS CLI is accessed through a web
browser.
SDM is available for all router platforms. The IOS CLI is available for a limited number
of Cisco devices.
SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of text-based
commands.\\\\\\\\\\\\\\\\
SDM is used for advanced configuration tasks. The IOS CLI is preferred for initial basic
device configuration.
3 Refer to the exhibit. Which password or passwords will be encrypted as a result of the
configuration that is shown?
4 Refer to the exhibit. Which three sets of commands are required to enable
administrators to connect to the Switch1 console over Telnet for configuration and
management? (Choose three.)
5 How does the SYST LED on the catalyst 2960 switch indicate a POST failure?
6 Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as
the IP address of the router LAN interface. A network administrator is using a laptop to
configure switch X with a default gateway. Assuming that the switch IP address is
192.168.5.147/24, what command will the administrator use to assign a default gateway
to the switch?
7 A technician has made changes to the configuration of a router. What command will
allow the technician to view the current configuration before he saves the changes?
8 Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the
modes and interfaces that can be protected with passwords. (Choose three.)
9 To save time, IOS commands may be partially entered and then completed by typing
which key or key combination?
Tab \\\\\\\\\\\
Ctrl-P
Ctrl-N
Up Arrow
Right Arrow
Down Arrow
10 What is the correct command sequence to configure a router host name to 'LAB_A'?
Router> enable
Router# configure terminal\\\\\\\\\\\\\\\\\
Router(config)# hostname LAB_A
Router> enable
Router# hostname LAB_A
Router> enable
Router# configure router
Router(config)# hostname LAB_A
Router> enable
Router(config)# host name LAB_A
11 Refer to the exhibit. From the router console, an administrator is unable to ping a
Catalyst switch that is located in another building. What can the administrator do from
her location to check the IP configuration of the attached switch?
12 Which two options must be selected in SDM Express to enable a router serial interface
to obtain an IP address automatically? (Choose two.)
13 What three settings can be made in the SDM Express basic configuration screen?
(Choose three.)
14 Which tasks can be accomplished by using the command history feature? (Choose
two.)
15 What option within Cisco SDM Express must be configured to allow hosts that
receive IP address settings from the router to resolve names on the network or Internet?
ATM
CHAP
Frame Relay \\\\\\\\\\\\\
HDLC \\\\\\\\\\\\\
PAP
PPP \\\\\\\\\\
17 Which command will display routing table information about all known networks and
subnetworks?
Router# show ip interfaces
Router# show ip connections
Router# show ip route \\\\\\\\\\\\\\\\
Router# show ip networks
console
AUX
Telnet \\\\\\\\\\
modem
19 Which three pieces of information about a neighbor device can be obtained by the
show cdp neighbors command? (Choose three.)
platform \\\\\\\\\\\
routing protocol
connected interface of neighbor device \\\\\\\\\\\
device ID \\\\\\\\\\\\\\\\
IP addresses of all interfaces
enable mode password
20
Which function is a unique responsibility of the DCE devices shown in the exhibit?
transmission of data
reception of data
clocking for the synchronous link \\\\\\\\\\\\\\\\\
noise cancellation in transmitted data
The host is configured in a different subnet from the subnet of the switch.
There is a duplex mismatch between the workstation and switch port.\\\\\\\\\\\\\\\
The switch port is running at a different speed from the speed of the workstation NIC.
The host has been configured with a default gateway that is different from that of the
switch.
24 Which of the following statements are true regarding the user EXEC mode? (Choose
two.)
Router(config-if)# enable
Router(config-if)# no down
Router(config-if)# s0 active
Router(config-if)# interface up
Router(config-if)# no shutdown //////////////////