Академический Документы
Профессиональный Документы
Культура Документы
INTRODUCTION
Today, every vital sector of the economy starting from agriculture to packaging, automobile, building
construction, communication or info tech have been virtually revolutionized by the applications of
plastics. Use of this non-biodegradable (according to recent studies, plastics can stay as
long as 4500 years on earth) product is growing rapidly and the problem is that what to do with
plastic-waste (Bale 2011). If a ban is put on the use of plastics on emotional grounds, the real cost
would be much higher, the inconvenience much more, the chances of damage or contamination
much greater, the risks to the family health and safety would increase and, above all the
environmental burden would be manifold. Hence the question is not Plastics vs. No Plastics but it
is more concerned with the judicious use and re-use of plastic-waste. India has witnessed a
substantial growth in the consumption of plastics and increased production of plastic waste (Verma
2008 and Nair 2011). The plastic waste is now considered as environmental hazard due to the
throw away culture.
If we are to achieve sustainable development, we will need to display greater responsibility
for the ecosystems on which all life depends, for each other as a single human community,
and for the generations that will follow our own, living tomorrow with the consequences of the
decisions we take today. (ICPE 2011)
The world is facing a waste crisis from the most problematic plastic produced today:
polyvinylchloride or PVC, commonly called vinyl. World production of PVC today is at more than 20
million tonnes per year up from 3 million tonnes in 1965 (Greenpeace 2011.).
Bitumen is a useful binder for road construction. The steady increase in high traffic intensity in terms
of commercial vehicles, and the significant variation in daily and seasonal temperature demand
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
improved road characteristics. Any improvement in the property of the binder is the need of the hour
(Sangita et al. 2011). The addition of polymers typically increases the stiffness of the bitumen and
improves its temperature susceptibility. Increased stiffness improves the rutting resistance of the
mixture in hot climates and allows the use of relatively softer base bitumen, which in turn, provides
better low temperature performance (Awwad et al. 2007 and Zainab et al. 2011). Use of waste
plastic in bitumen has revealed improved performance, stability, strength and fatigue life, reduction
in overall rutting, and low-temperature cracking of the bituminous surfacing. Apart from solving the
problem of waste disposal, addition of waste plastics in bituminous mix results in reduction in
consumption of bitumen thereby resulting in overall cost reduction (Sabina et al. 2009 and
Vasudevan 2006).
Salient features of the polymer-waste-bitumen mix road (Bale 2011, Vasudevan 2006, Mauskar
2008):
resistance towards water stagnation, plastic in bitumen provides im-permeability to the mix
In this study we report the reuse of waste of PVC pipes in the modification of bitumen for paving
applications. The visco-elastic properties of the modified bitumen and the mechanical properties of
the bituminous mix produced by this modified bitumen are investigated and compared to the neat
bitumen.
EXPERIMENTAL
Materials: Shredded PVC pipe waste (2-4 mm) materials were obtained from a local recycler. The
VG-10 grade paving bitumen from Mathura refinery of India was used. The physical properties of
bitumen are described in Table 1. The mineral aggregate (coarse aggregate (13.2 mm and 6 mm),
fine aggregates (stone dust), lime powder) was obtained from the local quarry and its physical
properties are given in Table 2.
Table 1: Properties of bitumen (VG-10)
Properties
Test Method
Value
IS 1203-1978
81
80-100
IS 1205-1978
48
> 40
Ductility at 25 C (5 cm/min)
IS 1208-1978
75+
>75
Specific gravity
IS 1202-1978
>0.99
Viscosity at 60 C, poise
IS 1206-1978
976
>800
IS 1206-1978
270
>250
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
Test Method
Value
MoRTH Specifications
21
24 max
2 max
Specific gravity,
2.63-2.65
2.5-3.0
IS 2386 (Part I)
21.25
30 max
Notes:
El: Elongation Index.
FI: Flakiness Index.
Preparation of blends: Mixing was performed in laboratory using an arrangement of oven, fitted
with a stirrer having a speed regulating system. The frequency of the stirrer was 2000 rpm for
preparing the blends and the time taken was 2-3 hrs. The waste PVC particles were thoroughly
washed and dried at 60 C. After washing the waste PVC was treated with a chemical for
homogeneous dispersion into bitumen. Treated PVC waste material was then used to modify neat
bitumen at two different percentages, 3% and 5% by wt of bitumen. The blends were prepared at a
temperature of 180 C. The resultant blend was stored at room temperature for further work. The
physical properties of bitumen with different percentages of PVC are given in Table 3.
Table 3: Properties of 80/100 pen bitumen with different percentage of PVC content
Properties
5% pvc
55
44
Softening point, C
55
58
Elastic recovery, %
32
25
4.30
5.0
Design of Bituminous Concrete (BC) mix: In the present study 30-45 mm BC mix was designed
as per Indian Road congress (IRC) guidelines section 500-18. The aggregates were blended to
obtain the values of standard BC grading given in Table 4 as specified by Indian Road Congress
(IRC).
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
Percent passing
Specified limits (IRC 500-18)
Adopted
19.0
100
100
13.2
79-100
96.2
9.5
70-88
86.3
4.75
53-71
62.6
2.36
42-58
44.1
1.18
34-48
36.6
0.600
26-38
30.6
0.300
18-28
27
0.15
12-20
18.1
0.075
4-10
7.6
Specimen Preparation: As per the MoRTH (Ministry of Roads and Transport, India) specification
for BC mix, when the specimens are compacted with 75 blows on either face, the designed BC mix
should fulfil the following requirements:
1. Marshall stability value kg (minimum)
= 900
= 2 to 4
= 3 to 5
= 65 to 75
Marshall Samples were made for each binder content at mixing and compaction temperature of
155-160 C and tested for determining the optimum binder content of the mix. The properties at
various percentages of binder content are given in Table 5.
Table 5: Marshall Parameters at various binder percentages
Binder %
by wt. of
mix
Bulk
density,
Gb, gm/cc
Stability,
kg
Flow (mm)
% Air
voids, Vv
VFB* (%)
VMA* (%)
4.76
2.34
1225
3.3
5.74
66.01
16.87
5.21
2.35
1357
3.5
4.65
72.42
16.87
5.66
2.36
1019
3.8
3.66
78.33
16.87
6.1
2.35
910
4.1
3.06
88.39
17.4
The optimum binder content was calculated to be 5.5%. The marshal parameters for mixes
prepared with different percentages of PVC pipe waste are given in Table 6.
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
Table 6: Marshall parameters of bituminous mix prepared with different percentages of PVC
waste
%pvc
Binder %
by wt. of
mix
Gt*
(g/cc)
Gb*
(g/cc)
% Air
voids,
Vv
% VMA
% VFB
Stability
Control
5.5
2.45
2.35
4.08
17.01
76
1116
5.5
2.45
2.36
3.67
16.65
77.94
1372
5.5
2.45
2.37
3.27
16.3
79.97
2196
* Gt theoretical specific gravity of the mix, Gb bulk density of the marshal specimen.
Rheology of modified bituminous binders: The viscoelastic response of the modified bituminous
binders was evaluated using a Dynamic Shear Rheometer with parallel plate geometry by
measuring complex shear modulus and phase angle. Measurements were taken in the temperature
range 50 C to 85 C. The 25 mm steel plate was used, the gap width set was 1 mm and all
measurements were taken at a frequency of 10 rad/s. The DSR measures a specimen's complex
shear modulus (G*) and phase angle (). The complex shear modulus (G*) can be considered the
sample's total resistance to deformation when repeatedly sheared, while the phase angle (), is the
lag between the applied shear stress and the resulting shear strain. The specified DSR oscillation
rate of 10 rad/s (1.59 Hz) is meant to simulate the shearing action corresponding to a traffic speed
of about 55 mph (90 km/hr). G* and are used as predictors of HMA rutting and fatigue cracking.
Early in pavement life rutting is the main concern, while later in pavement life fatigue cracking
becomes the major concern. While performing the test, the samples were denoted as:
Sample 1: pen 80/100 + 3% PVC
Sample 2: pen 80/100
Sample 3: pen 80/100 + 5% PVC
Figures 1 to 6 shows the viscoelastic behavior of PVC waste modified binders and the neat binder
i.e. pen 80/100.
G is defined as the ability of the material to store energy in the cycle of the deformation and G is
the energy dissipated as heat in the cycle. G and G are plotted as a function of temperature at
constant frequency of 10 radians/sec in Figures 1 and 2.
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
10000
1000
100.0
G'(Pa)
10.00
1.000
50.0
55.0
60.0
65.0
70.0
temperature(C)
75.0
80.0
85.0
1.000E5
10000
G''(Pa)
1000
100.0
50.0
55.0
60.0
65.0
70.0
temperature(C)
75.0
80.0
85.0
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
10000
1000
|n*|(Pa.s)
100.0
10.00
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
temperature(C)
1.000E5
10000
|G*|(Pa)
1000
100.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
temperature(C)
Figure 4: Complex modulus of neat and waste PVC modified binders at different
temperatures
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
90.00
80.00
70.00
60.00
delta
(degrees)
50.00
40.00
30.00
20.00
10.00
0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
temperature(C)
Figure 5: Comparison of phase angle of neat and PVC waste modified binder
100.0
10.00
G*/sin
1.000
0.1000
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
temperature(C)
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
Mix Performance Tests: A number of tests can be used to characterize the mechanical properties
of BC mixtures. The tests used in this study are retained stability, indirect tensile strength test and
wheel tracking test. Each of these tests is described in detail in the following sections.
Retained Stability Test: Retained Stability is the measure of moisture induced striping in the mix
and subsequent loss of stability due to weakened bond between aggregates and binder. The test
was conducted on the Marshall machine with the normal Marshall samples. The stability was
determined after placing the samples in water bath at 60 C for half an hour and 24 hours.
Retained Stability (%) =
Avg. stability
after half an
hour in water
at 60 C
Avg. stability
after 24
hours in
water at 60 C
Avg. retained
stability %
1116
839
75.2%
1372
1098
80%
2196
1804
82.2%
Design
requirement
Minimum 75%
(as per MoRTH
Table 500-17)
Indirect Tensile Strength Test and Tensile Strength Ratio: The tensile strength determined by
tests other than the straight pull test is designated as indirect tensile strength. This test method
measures the splitting tensile strength of bituminous mix specimens by the application of a
diametric compressive force on a cylindrical bituminous mix specimen placed with its axis horizontal
between the plates of a compressive testing machine. The indirect tensile test, which is tensile
strain at failure, is useful in predicting the cracking potential. The test procedure adopted for indirect
tensile and tensile strength ratio was as per AASHTO T283. The test temperature is maintained at
25 C and the specimens are conditioned at 25 C for 2 hours prior to the test. A 0.5 inch (12.7 mm)
wide curved loading strips used to provide a uniform stress distribution. The load at which the
specimen fails is taken as the indirect tensile strength (also referred as the dry indirect tensile
strength) of the bituminous mix.
The tensile strength ratio of the bituminous mixes is used to determine the moisture susceptibility of
the mixes. The standard Marshall samples are prepared for each binder. The specimens are placed
in the water bath maintained at 60 C for 24 hours and then immediately placed in the
environmental chamber maintained at 25 C for two hours. These conditioned samples are then
tested for Indirect Tensile Strength. The indirect tensile strength of these soaked samples are called
wet indirect tensile strength. The ratio of the wet to dry indirect tensile strength is recorded as
Tensile Strength Ratio (TSR) of the bituminous mix.
Indirect tensile strength of the specimen is calculated as follows:
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
Where, P is the load (kg), d is the diameter in cm of the specimen; t is the thickness of the
specimen in cm. The TSR of specimen was computed by following formula:
100
12.15
9.67
Tensile
strength ratio
(%)
79.6
13.03
10.94
84
17.43
15.33
87.9
Design
requirement
Minimum 80%
(as per MoRTH
Table 500-17)
Rut depth studies by wheel tracking test: Rutting is an important parameter for design as well as
for evaluation of performance of a bituminous mixture. To check the rutting resistance of the
mixtures, tests were performed by Wheel Tracking Device (WTD), which is destructive test and
involves direct contact between the loaded wheel and the rectangular test specimens. The test was
conducted on the prepared slab specimen of 300X150X50 mm at optimum binder content
containing PVC pipe waste. The test was conducted at 50 C and the resulting rut depth was
measured. The data of rut depth of different BC mixtures are plotted in Figure 1. Also the rut depth
in different cycle range is presented in Table 9. Photo1 shows the view of rutted slabs.
Table 9: Wheel tracking results
No. of passes
Conventional 80/100
1260
5.82
3.46
2.05
2520
7.32
4.38
2.69
3780
8.26
4.94
3.91
5040
8.96
5.15
4.45
6300
9.29
5.8
5.23
7560
10.01
5.59
8820
10.44
6.56
5.81
10080
10.73
6.88
6.24
11340
11.08
7.09
6.52
12600
11.37
7.57
6.81
13860
11.66
8.01
7.26
15120
11.96
8.37
7.56
16380
12.47
8.63
7.81
10
25th A
ARRB Confere
ence Shaping
g the future: Linking policy, research
r
and o
outcomes, Perth, Australia 2
2012
Photo 1: View of ru
utted slabs
Fig
gure 7: Rut depths
d
vers
sus No. of pa
asses
RES
SULTS AND DISC
CUSSION
N
Physical propertie
es of bitumen
n and minerall aggregate are
a shown in Table 1 and 2 respective
ely.
Resullts of test on aggregate given in Table
e 2 indicate th
hat test value
es meet requirement of In
ndian
Road Congress sp
pecifications (IRC SP 79 2008). Classsification tests were perfo
ormed on bitu
umen,
and th
he results show that the b
bitumen used
d is well withiin the limits of
o pen 80/100
0 bitumen. Similar
tests w
were also pe
erformed on b
blends prepa
ared by mixin
ng 3% and 5%
% of PVC pip
pe waste in to
o pen
80/10
00 bitumen. R
Results are given in Table
e 3 and the re
esults show that the addittion of waste PVC
increa
ases the stiffn
ness of the b
binder. Resultts given in Ta
able 4 showss that the agg
gregate propo
ortions
selectted were welll within the IR
RC specified
d limits. Data given in Table 5 reveals tthat the optim
mum
bitumen content iss 5.5% by we
eight of mix a
and also mee
ets the requirements as de
escribed in IR
RC
sectio
on 500-18.
Visco
oelastic Response of Binder: Resultts in Figures 1 and 2 show
w a decrease
e of G and G
G
modu
uli with increa
asing tempera
atures. G an
nd G moduli of bitumen-w
waste PVC blends are hig
gher
than tthose of neatt bitumen ove
er the entire temperature range as shown in Figure
es 1 and 2. The
T
increa
ase in G refle
ects the incre
ease in the stiffness of the
e bitumen ble
ends, compa
ared with thatt of
pure bitumen.
b
Butt the increase
e in G indica
ates an increa
ase in the visscous respon
nse. The storrage
modu
ulus (G) of wa
aste PVC mo
odified binde
er was higherr than neat biitumen as sh
hown in Figurre 1. It is
maxim
mum for the b
bitumen mod
dified with 5%
% waste PVC
C. The loss modulus (G) of
o modified b
blend
11
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
was significantly higher than the neat bitumen as shown in Figure 2. Higher values of loss modulus
indicate more resistance of the binder to permanent deformation.
Figure 3 shows an increase in complex viscosity by the addition of waste PVC to bitumen over the
entire temperature range. The complex viscosity reduces with increasing temperatures but it is
more for bitumen blends. Figure 4 shows almost linear relationship between complex modulus G*
and temperature. The slopes of the lines are similar for both (3% and 5%) waste PVC modified
bitumen but is higher than the neat bitumen. The 5% waste PVC modified bitumen has the highest
modulus in the temperature range as shown in the Figure 4. Higher modulus at high temperature
indicates better resistance to permanent deformation (rutting).
Figure 5 shows that the phase angle () of waste pvc modified bitumen was lower than that of neat
bitumen. The phase angle of 5% waste PVC modified bitumen was considerably lower than that of
unmodified bitumen. Lower phase angle indicates lower viscous flow and higher elastic response.
This indicates that polymer modified binders have high consistency and elasticity. Figure 6 shows
there was an increase in the G*/sin parameter of the original binder when the waste PVC was
mixed. This indicates that the stiffness of the modified binder increases with the increase in the
percentage of PVC and decreases with the increase in the temperature.
Performance of the Mix: Results given in Table 7 indicates that retained stability of the mix
increased with the incorporation of waste PVC. This indicates that the bond between the aggregate
and the binder becomes stronger with the addition of waste PVC particles. When 3% waste PVC
was added the retained stability of the mix increased up to a value of 80% from 75.5% of the neat
binder and when 5% waste PVC was added the retained stability of the mix increased up to a value
of 82.2%.
The tensile strength ratio of the bituminous mixes determines the moisture susceptibility of the
mixes. TSR is widely accepted test to address damage caused by the ingress of moisture. The
values of TSR of BC containing 3% and 5% waste PVC are recorded as 84% and 87.9% in
comparison to the 79.6% of the control BC mix.
Rutting is a key factor for design as well as evaluation of the performance of bituminous concrete
mixtures. It can be seen from Table 9 and Figure 7 that observed rut depth values for 3% and 5%
waste PVC modified mixes are much lower than that of control mix. Data plotted in Figure 7 indicate
that higher resistance to rutting is observed when waste PVC is added to the binder, indicating
better resistance to permanent deformation. The same was also observed while studying the
viscoelastic response of the waste PVC modified binder, where it showed higher values of complex
modulus,G* in case of modified binders. The increased rutting resistance due to the addition of
waste PVC particles is because of better moisture resistance of the mix containing waste PVC and
also due to the better strength of the mix achieved.
CONCLUSIONS
Based on the results of the laboratory study the following conclusion can be drawn:
The addition of PVC pipe waste to the bitumen enhances both the binders as well as the
mixs properties.
Waste PVC modified binder showed better G and G values which concludes to the
increased stiffness of the binder as well as better viscous response of the binder.
Improved phase angle and complex modulus values were achieved after addition of waste
PVC to the binder. It shows better resistance to the permanent deformation of the mix as
compared to the mix prepared by neat VG 10 binder.
12
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
Use of waste PVC led to the increase in values of indirect tensile strength to resist cracking.
Addition of waste PVC reduced the rutting values of the bituminous mix to a greater extent.
ACKNOWLEDGEMENTS
Sincere thanks are due to Dr. S. Gangopadhyaya Director CSIR-Central Road Research Institute,
New Delhi 110025 for his permission to publish this paper.
REFERENCES
Anderson, D.A. (1992), Rheological Properties of polymer Modified Asphalt Binders, ASTM STP
1108, pp 20-34
Awwad, M.T., Shbeeb, Lina (June 2007), The Use of Polyethylene in Hot Asphalt Mixes, American
Journal of Applied Sciences
Baker, R.E (1998), Polymer Modified Bitumen, Indian Highways, Vol. 1. pp 85-94
Bale, A.S. (2011), Potential reuse of Plastic waste in Road Construction: A review, Eco-Web India
Bandyopadyay, G.G., Bhagawan, S.S., Ninan and Thomas, S. (1997), Viscoelastic Behaviour of
NBR/EVA Polymer Blends: Application of Models, Rubber chemical Technologist, Vol.70, pp650-662
Brisco, O. (1987), Asphalt Rheology: Relationship to Mixture, ASTM Committee D-4 Symposium on
Road and Paving Material, West Conshohocken. Pa.
Chen, J.S., Min-Chih Liao, P.E. and Ming Shiah (2002), Asphalt Modified by Styrene Butadiene
Styrene Triblock Coploymer: Morphology and Model, Jof Materials in civil Engineering, May/June,
pp 224 -229
Collins, J.H.M.G., Bouldin, R., Gelles and Berker, A. (1991), Improved Performance of Paving
Asphalt by polymer Modification, APT, Vol.60
Deepak, N.K. (2011), A study to assess the effectiveness of structured teaching programme on
hazards of plastic waste and its safe disposal among a selected rural community area at Bangalore,
Nightingale College of Nursing, Bangalore
Greenpeace (2011), PVC Waste and Recycling, The PVC waste crisis, Greenpeace Toxic Site.
archieve.greanpeace.org viewed on 13th November 2011
Habib, N.Z., Kamaruddin, I., Napiah, M. and Tan, I.M. (2011), Rheological Properties of
Polyethylene and Polypropylene Modified Bitumen, International Journal of Civil and Environmental
Engineering
Hanson, D.I., Mallick. R.B. and Foo, K. (1995), Strategic Highway Research Program Properties of
Asphalt Cement, TRP, 1488, pp40-51
Highlights (2004), Recycling of Plastics through Environmentally Sound Process, CPCB News
Letter (Central Pollution Control Board) India, viewed on 13th November 2011, www.cpcb.nic.in
Indian Centre for Plastics in the Environment (2011), Facts given by Indian Centre for Plastics in the
Environment (ICPE) on PVC waste, posted on http://www.icpenviro.org, viewed on 14th November
2011
13
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
IRC:SP-53 (2002), Guidelines on use of Polymer and Rubber Modified Bitumen in Road
Construction, New Delhi
IS:1201 to 1220 (1978), Methods for Testing Tar and Bituminous Materials, Indian Standard
Institution, New Delhi
IS:73:2001 (2001), Paving Bitumen Specification, Indian Standard Institution, New Delhi
Isacsson, U. and Lu, X. (1999), Laboratory Investigation of polymer Modified Bitumens, J.Asso,
Asphalt Paving Technol., 68, pp 35-63
Kandhal P.S. (1993), Waste materials in hot mix asphalt-an overview, ASTM, STP 1193, pp. 3-17
Lewandowski, L.H. (1994), Polymer Modification of Paving Asphalt Binders, Rubber Chem.
Technol.,67, 447-480
Maccarrone, S., Holleran, G. and Gnanaseelan, G.P. (1995), Properties of Polymer Modified
Binders and Relationship to Mix and Pavement Performance, Asphalt Paving Technology, pp209240
Mauskar J.M (2008), Study on Performance Evaluation of Polymer Coated Bitumen built Roads,
I.A.S CPCB India
Ministry of Road Transport and Highways (2001), Specifications for Roads and Bridge Work, Fourth
Revision , IRC, New Delhi
Rogge, D.F., Terrel, R.L. and George, A.J. (1992), Polymer Modified Hot Mix Asphalt Oregon
Experience Rheological Properties of Polymer Modified Asphalt Binders, ASTM STP 1108 , pp151172
Sabina, Khan T.A., Sangita, Sharma D.K. and Sharma B.M. (2009), Performance Evaluation of
Waste Plastic modified Bituminous Mixes, Journal of Scientific and Industrial Research
Sangita, Khan T.A., Sabina and Sharma D.K. (2011), Effect of waste polymer modifier on properties
of bituminous concrete mixes, Construction and Building Materials, No 25 3841-3848
Vasudevan, R. (2006) Utilization of waste plastics for flexible pavement, Indian High Ways (Indian
Road Congress), July 2006
Verma S.S. (2008), Roads from Plastic Waste, The Indian Concrete Journal, p 43-44
AUTHOR BIOGRAPHIES
Ambika Behl: is a Scientist in Flexible Pavement Division at CSIR-CRRI. She is working in this
area from last 5 years. She is a Chemical Engineer with Masters Degree in Polymer Technology
and is currently pursuing her PhD in the area of Warm Mix Asphalt from IIT Roorkee, India. She has
done many research projects in the area of modified binders for paving applications. She is a
member of Indian Road Congress and also a committee member of Bureau of Indian Standard.
Dr P.K. Jain: is chief scientist and Head Flexible pavement division at CSIR_ Central Road
Research Institute, New Delhi-110025.He is also coordinator of Academy of Scientific and
Innovative Research and secretary research council. He is member of various committees of Indian
Road Congress and Bureau of Indian Standard. He has over 35 years research experience and
produced over 125 publications. He is responsible for developing a number of standards and
specifications for IRC and BIS related to flexible pavements and bituminous materials.
14
25th ARRB Conference Shaping the future: Linking policy, research and outcomes, Perth, Australia 2012
15