Академический Документы
Профессиональный Документы
Культура Документы
9) In NDT?
A) In RT, 680 dia, 20mm thickness, DWDI is used
B) In RT, 70mm dia, 60mm Thickness, DWSI is used
C) In RT, 85 mm dia, 25 mm thickness, DWDI is used
D) A will be used by DWDI & DWSI
10) In RT .?
A) Radiography will show lack of fusion as dark straight line in one side and other side
bright
B) Radiography will show undercut as dark straight line in one side
C) Radiography will show lack of root penetration in one side bright and other side dark
D) None of the above
11) In contract, they said 20% RT and every one failure 2RT required and you would find one
failure. What would you your action.?
A) You agree and you will show substituent the joint
B) You disagree and leave the Joint
C) You will ask more % of RT for Quality Assurance
D) None of the above
12) Tensile Test give.?
A) Longitudinal weld metal shows reduction in area as 20%
B) Transverse specimen show reduction in area as 25%
C) It will be Show only Rm
D) Both A & B
13) In MMA .?
A) DC-ve gives deeper penetration than DC+ve
B) AC gives greater deposition than DC-ve
C) DC-ve gives greater deposition than DC+ve
D) None of the above
14) Lamellar Tearing detected by?
A) RT
B) Ut
C) Visual Inspection
D) None of the above
15) According to BS EN, Consumables E50 3 B. In these 3 indicates .?
A) Toughness
B) Yield Strength
C) Chemical Composition
D) None of the above
16) What would you consider while calibrating MIG Welding operation?
A) Amps, Volts, Travel Speed, Gas rate Flow
B) Amps, Volts, Travel Speed, Welding Consumable
C) Amps, Volts, Travel Speed, CTOD
D) None of the above
17) Oxy Fuel Cutting Chemical Reaction.?
A) Exothermic Reaction
B) Endothermic Reaction
C) Convection Reaction
D) None of the above
24)Tig Welding..?
A)
B)
C)
D)
Toughness
Hardness
Re Only
Rm and Re
Curies
Kilo Volts
Joules
Electron Volts
After Welding
Before Welding
Before Welding and Before next pass
None of the Above
It is Important
Length and Position depends on material thickness and size
It always require preheat
None of the Above.
31) You noticed an excess penetration in a C/Mn welded country pipe line, what could be the
reason...?
A)
B)
C)
D)
Wrong Electrode
Contaminated Electrode
Excess Root Grinding
Large Root Face
32) Which type of electrode is not best for Welding Cross country pipe line...?
A)
B)
C)
D)
Basic
Rutile
Cellulose
Iron powder
34) Which of the following has the great effect of current during MIG/MAG welding..?
A)
B)
C)
D)
Arc Length
Arc Voltage
Flow rate
WFS
WFS is Constant
ARC length is Constant
Current is Constant
None of the above.
Chromium
Carbon
Manganese
Nickel
High Strength
Hardness
Toughness
Good Through Ductility
ASME Section V
ASME Section II
ASME Section IX
ASME Section VIII
Notch Toughness
Hardness
%E
%E and %Z
46) A Fillet Weld has a design throat thickness of 6mm, what is the leg length Size....?
A)
B)
C)
D)
8.4 mm
5 mm
8.5 mm
More information needed
47) What type of standard formed in a metal with low heat input during welding....?
A)
B)
C)
D)
Austenite
Pearlite
Bainite
Martensite
48) What is the heat input for MMA Welding of C-Mn with given variables 22V/250A,
250mm/min?
A)
B)
C)
D)
1.056 KJ/cm
1.056 KJ/mm
1.56 J/mm
1.56 J/cm
50) Which of the following statement for hydrogen control are true....?
A)
B)
C)
D)
MMA basic electrode will introduce more hydrogen than Agglomerated basic flux
TIG welding will introduce more hydrogen than Agglomerated Acid flux
MAG solid wire will introduce less hydrogen than fused basic flux
None of the Above.
A)
B)
B)
D)
56) In a SAW welding process, which could be reason for centre line crack....?
A)
B)
C)
D)
57) Hydrogen Induced Cold Cracking occurs 48-72 Hr after welding, what could be the
reason...?
A)
B)
C)
D)
RT
PT
UR
MT
Butt weld
Fillet Weld
Seam weld
Spot weld
Resistance welding
Explosive Welding
Braze welding
Friction Welding
62) Which of the following welding process is described as Solid state Welding...?
A)
B)
C)
D)
Friction Welding
Electro Slag Welding
Resistant welding
None of the Above