Академический Документы
Профессиональный Документы
Культура Документы
TECHNICAL
CATALOGUE
January 2008
aquatherm SHT
Application
aquatherm SHT connection pipe (grey)
In coils 16 25 mm and straight lengths. Produced
from the highly flexible material Polybutylene (PB)
The aquatherm SHT system is applicable in the field of:
Advantages
The advantages of the aquatherm SHT sliding sleeve
system are:
Contents:
Index
Applications/ Advantages
4-6
General Requirements
Materials
Connection Technique
10
11
Support Intervals
12
13
Test Sheet
14 19 Product Range
BRANZ
DVGW
SKZ
AMS Laboratories
AS/NZS4020
WRAS
TZW
Quality assurance
Aquatherms production of a quality controlled pipe system demands the supervision regulations &
control of all work operations. All results and processes have to be documented and meet the
requirements of
DIN guidelines
DVGW working sheets
Supervisory regulations of the SKZ
Product Description
aquatherm SHT (PB) Pipe
Colour grey
Markings
aquatherm SHT 16x25mm - - - ART NR - - - PB 125 - - - DIN16969/DIN16968 - - - DIN 4726 - DVGW-au 2075 0484/98 - - - DATE MTR - - KENNZ MADE IN GERMANY
Markings
Diameter, DR,
aquatherm SHT pipe to DIN 16968 & DIN 16969 complete with sliding sleeves to DIN 16928 and
accessories brand matched
Must be installed to the requirements of the NZBC (all relevant clauses) and in accordance
with manufacturers technical requirements.
Must be installed by an aquatherm registered installer.
Can be used for flow and return hot water ring mains within the parameters of
temperature and pressure chart.
Pipe (only) can be laid directly in concrete/plaster and solid walls in accordance with
aquatherm SHT installation procedures.
All in ground services & inslab installations must be installed to AS/NZS 3500.5.2000
Clause 2.13.2.
Pipe must be clipped as to aquatherm support intervals for SHT using brand matched clips
or clippets. Ensure all pipe work is installed to NZBC requirements.
Can be used for radiator connections however it is recommended that EVOH barrier
products are installed in accordance with DIN 4721 & pipe work is clearly identified as
heating flow and return.
Pipes & fittings shall not be used within 1 meter of the inlet or outlet of a water heater.
Pipe & fittings shall not be used when exposed to direct sunlight.
Is not suitable for chemicals or petroleum oils.
Pipe must not be used on the flow & returns from solar panels, wetbacks or relief drains
of an uncontrolled heat source.
When connecting to other piping systems always use thread connector. Do not use
aquatherm Sliding Sleeve connector.
When used as an alternative non potable supply, ensure pipes are clearly & permanently
labeled in accordance with AS1345 & AS1319.
Testing
Confirm the timing before carrying out any tests. Supply potable water and the apparatus needed.
Ensure that all fixtures/ appliances / tanks / water heater / tape ware and valves are isolated
before commencing testing. Test to aquatherm SHT test procedures as applicable.
aquatherm NZ Ltd must receive this information within 3 months of the installation for the
warranty to be valid. Please consult with your local area Council as they may require a copy of the
test results for their records.
Note
When testing aquatherm SHT pipes that are connected to fusiotherm pipes the fusiotherm test
is to be used for both pipe systems.
Pipe Fittings
Material:
Manufactured from DR brass to AS3688
Characteristics:
All fittings of the aquatherm SHT system
are in accordance with the latest European
Potable Water Standards and tested to
AS/NZS 4020. Made from a dezincification
resistant brass. This type of brass has been
developed especially for the application in
areas with aggressive water.
Aquatherm applies this standard brass for
all metal fittings and connection pieces.
SLIDING SLEEVE:
Sliding Sleeve:
The connection technique sliding sleeve is an
interlocking connection type.
Tool Change:
The interchangeable head of the expanding tool
is screwed off then the required dimension is
fixed.
Only remove the bolts to change both inserts of
the aquatherm SHT mounting tool. After
inserting the false jaw the bolts need to be
inserted in opposing directions (image 1)
One ring sleeve, for use only on EVOH pipe for
underfloor heating and radiator connections
CONNECTION TECHNIQUE:
aquatherm SHT
10
Sound Insulation
The sound insulation qualities of the SHT pipe system, when related to water flow and hydraulic
shock within a building, provide a sound proofing effect on noise transmission.
Therefore the sound transmission is much lower compared to metallic pipes.
Heat Conductivity
aquatherm SHT pipes manufacture from Polybutylene have a heat conductivity of 0.22 W/mK. This
means in terms of heat transfer aquatherm SHT pipes has a significantly higher degree of self
insulation compared to metallic pipes.
Note: aquatherm supplies pre insulated SHT EVOH oxygen tight pipes, suitable for potable water
ring mains and radiator non potable applications.
11
12
13
Liability Warranty
Furthermore within the scope of this aquatherm GmbH gives a 10 year guarantee which compensates for
material damage to third persons, for investigation, removal, replacement, acceptance, dismounting or laying
bare of all defective goods.
aquatherm GmbH guarantee is conditional on :
The fusion or joining of pipe and fittings using only aquatherm GmbH welding tools
and devices.
Installation of pipe and fittings are certified Aquatherm installers and adherence to
aquatherm GmbH technical rules and guidelines for correct installation principles.
Limits of Liability
For bodily injury
For property damage
(Per occurrence)
5.000.000, Euro
2.500.000, Euro
Installation Address
Description of installation
Name of Contractor
Date of Completion
Signature
Reg Installer Number
This Warranty must be fully completed, signed and returned with the completed test sheet within three months
of the completion of the project installation to the New Zealand Agent: Aquatherm NZ Ltd
PO Box 99 393, Newmarket, Auckland, NZ. Phone 09 570 7204, Fax 09 570 7206
14
Address:
Preliminary test
Test pressure 15 bar
1. Test pressure 15 bar 30 minutes
2. Pressure drop after 30 minutes max
0.6 bar.
3. Result pressure test
Type of Installation: ..
Pipe Lengths:
16mmm
20mmm
25mmm
Time testing started: .
Time testing finished:
Test period:
(minutes)
Client: .
.
.
.
Contractor:
.
Note:
When testing with aquatherm SHT pipes that
are joined to fusiotherm, the fusiotherm
test is to be used for both systems.
Date:
Declaration:
Installer #: ____________________
Signature: _____________________
aquatherm NZ Ltd must receive this information within 3 months of the installation for the
warranty to be valid. Please consult with your local area Council as they may require a copy of
the test results for their records.
15
Pipes:
aquatherm SHT PB pipes
Art. No
PT477020
PT477022
PT477024
PT477040
PT477042
PT477044
Dimension
16 x 2.0mm
20 x 2.0mm
25 x 2.3mm
16mm
20mm
25mm
Packing
Unit
100m Coil
100m Coil
50m Coil
4m Lengths
4m Lengths
4m Lengths
Price
Unit
ea
ea
ea
ea
ea
ea
Dimension
16 x 2.0mm
20 x 2.0mm
Packing
Unit
50m Coil
50m Coil
Price Unit
ea
ea
Dimension
16 mm
20 mm
Packing
Unit
100m Coil
50m Coil
Price Unit
ea
ea
Fittings:
aquatherm SHT wingback elbow
Art. No
Dimension
PT79000
PT79002
16mm x
20mm x
Packing
Unit
1
1
Price Unit
Ea
ea
Dimension
PT79040
16mm
Packing
Unit
1
Price Unit
ea
16
Dimension
PT79045
16mm
Packing
Unit
1
Price Unit
ea
Dimension
PT79006
16 x
Packing
Unit
1
Price Unit
ea
Dimension
PT79100
PT79102
PT79107
16 x 16 x 16mm
20 x 20 x 20mm
25 x 25 x 25mm
Packing
Unit
1
1
1
Price Unit
ea
ea
ea
Dimension
16
20
20
20
25
x
x
x
x
x
20 x
16 x
16 x
20 x
20 x
16mm
16mm
20mm
16mm
25mm
Packing
Unit
1
1
1
1
1
Price Unit
ea
ea
ea
ea
ea
Dimension
16mm x
20mm x
Packing
Unit
1
1
Price Unit
ea
ea
Dimension
16mm x
20mm x
25mm x 1
Packing
Unit
1
1
1
Price Unit
Packing
Unit
1
1
1
Price Unit
ea
ea
ea
Dimension
16 x 16mm
20 x 20mm
20 x 16mm
reducing
25 x 25mm
25 x 20mm
reducing
1
1
ea
ea
ea
ea
ea
17
Dimension
16mm 90
20mm 90
25mm 90
Packing
Unit
1
1
1
Price Unit
ea
ea
ea
Dimension
20/16 x 2.0mm
20/20 x 2.0mm
25/20 x 2.0mm
Packing
Unit
1
1
1
Price Unit
ea
ea
ea
Dimension
40/16
40/20
50/16
50/20
x 2.0mm
x 2.0mm
x 2.0mm
x 2.0mm
Packing
Unit
1
1
1
1
Price Unit
ea
ea
ea
ea
Dimension
16 x mm
20 x mm
16 x mm
swivel elbow
Packing
Unit
1
1
1
Price Unit
ea
ea
ea
Dimension
16mm
20mm
Packing
Unit
1
Price Unit
ea
Dimension
PT79990
PT79992
AH79990
AH79992
AH79994
16mm
20mm
16mm EVOH Pipe
20mm EVOH Pipe
25mm
Packing
Unit
1
1
1
1
1
Price Unit
ea
ea
ea
ea
ea
18
Dimension
16mm
20mm
Packing
Unit
1
Price Unit
ea
Dimension
16mm
20mm
25mm
Packing
Unit
1
1
1
Price Unit
ea
ea
ea
Dimension
16mm red
20mm red
16mm blue
20mm blue
Packing
Unit
50
50
50
50
Price Unit
ea
ea
ea
ea
Dimension
For 16, 20,
25, 32mm
Packing
Unit
1
Price Unit
ea
Dimension
for 16mm
for 20mm
for 25mm
Packing
Unit
1 set
1 set
1 set
Price Unit
ea
ea
ea
Dimension
Up to 25mm
Packing
Unit
1
Price Unit
ea
Dimension
PT50800
for 16 - 20mm
Packing
Unit
1
Price Unit
ea
19
Dimension
PT50817
PT50818
for 16 - 20mm
for 25mm
Packing
Unit
1
1
Price Unit
ea
ea
Dimension
PT50804
for 16 - 20mm
Packing
Unit
Set
Price Unit
ea
Dimension
PT50808
For 16-25mm
Packing
Unit
Set
Price Unit
ea
20
Exclusive Distributor
Contact the Plumbing World
Commercial Project Team for competitive
pricing for large projects
Ph: 0800 107 428
21