Академический Документы
Профессиональный Документы
Культура Документы
TM
TM
TM
Table of Contents
10
11
Mechanical Performance
12
13
Installed Weight
14
15
16
17
18
Introduction
The Huck UNIMATIC Blind Rivet System combines many important features, which
develop optimal joint characteristics along with most convenient field installation. Over
the years, several product refinements helped to continuously update the product.
Materials
The Huck Unimatic blind rivet system is available in all-Aluminum for lightest weight,
Monel for improved corrosion resistance and A-286 for highest strength and elevated
temperature applications.
Cross Section View
The generous foot print is ideal for applications in thick or thin, metallic and nonmetallic structure. It may be installed on blind side slopes up to 5 without loss of
performance.
A combination of selected materials, cold working and thermal processing targets the
optimum balance between joint performance and functional reliability in each of the 3
basic material combinations.
Joint Strength
The targeted combination of the above features culminates in a blind rivet system
with highest joint allowables and highest strength to weight ratios in its class. Joint
data are published in MIL-HDBK-5.
Drive Washer
To enhance installation convenience in the factories and repair activities, the time
proven system is now available with integral drive washers. Each rivet has in
effect a new drive anvil. This new feature allows installation of multiple diameters
with one and the same installation nose attachment and eliminates concerns about
tool wear.
NAS1919B04S02
NAS1921M05S03
NAS1921C06S04
OSMLSP-B04-02
OSMLS100-M05-03
OSMLS100-C06-04
Specials
Certain sizes and materials are available in reduced shear head style (NAS1097) for
special applications in the traditional Huck MLS double action configuration or
with the optional drive washer for single action installation.
Sleeve
Lock Collar
Optional
Drive
Washer
Spindle
The Installation schematic shown below applies to the traditional UNIMATIC (single
action) rivets. Each rivet diameter requires a separate nose assembly.
Step One
The rivet is placed into the prepared hole with
clearance. The installation tool engages the pintail
and the cycle begins. The pulling load is reacted
against the lock collar.
S t e p Tw o
The spindle moves through the rivet sleeve forcing
hole fill by means of an interference fit lobe on the
spindle. Eventually the spindle head contacts the end
of the sleeve and blind side bulb formation begins.
Step Three
Continued motion of the spindle starts pulling the
sheets together and forming the blind side bulb. As
the lock groove of the spindle aligns itself with the
lock pocket of the sleeve, the lock collar is swaged
into the lock cavity.
Step Four
As the pulling load continues to increase, the spindle
separates in the break neck. The spindle break is
flush with the rivet head, the lock is firmly in place
and the installation is complete. The entire installation cycle is accomplished in less than 2 seconds.
The Installation schematic shown below applies to the UNIMATIC (single action) rivets with
optional drive washer. Diameters -4, -5 & -6 are installed with one and the same nose assembly.
Drive Was her
Step One
Lock
Collar
S t e p Tw o
The spindle moves through the rivet sleeve forcing
hole fill by means of an interference fit lobe on the
spindle. Eventually the spindle head contacts the end
of the sleeve and blind side bulb formation begins.
Step Three
Continued motion of the spindle starts pulling the
sheets together and forming the blind side bulb. As
the lock groove of the spindle aligns itself with the
lock pocket of the sleeve, the lock collar is swaged
into the lock cavity.
Step Four
As the pulling load continues to increase, the spindle
separates at the break neck. The spindle break is
flush with the rivet head, the lock is firmly in place,
the drive washer is discarded and the installation is
complete. The entire installation cycle is accomplished in less than 2 seconds. Concerns about tool
wear are eliminated.
Sleeve Code:
Blank For 5056
Code C For A-286
Code M For Monel
Length
Manufacturers
Identification
(C)
Grip Number
Grip
Installed Rivet
Part
Number
SMLS100-(*)04-(**)
NAS1921(*)04S(**)
SMLS100-(*)05-(**)
NAS1921(*)05S(**)
SMLS100-(*)06-(**)
NAS1921(*)06S(**)
SMLS100-(*)08-(**)
NAS1921(*)08S(**)
Size
1/8
-04
5/32
-05
3/16
-06
1/4
-08
Rivet Nominal
Diameter
A Dia.
+.003 -.001
B Dia.
.004
(C) Ref.
Head Height
G Min.
Dimension
.125
.125
.225
.042
.788
.156
.156
.286
.055
.788
.190
.187
.353
.070
.788
.250
.250
.476
.095
1.000
(*) Indicates material code letter. (**) Indicates grip length number.
Rivet
Grip Range
Min.
Max.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
SMLS100-(*)04
NAS 1921(*)04
Length Max.
F Max.
.213
.260
.323
.385
.448
.510
.573
.635
.698
.760
Grips
-01
-02
NOTE A
-04
.057/.078
.079/.125
SMLS100-(*)05
NAS 1921(*)05
Length Max.
F Max.
.342
.431
.516
.641
.766
.891
1.016
1.141
1.266
1.391
Diameters
-05
.075/.100
.100/.125
.238
.263
.336
.398
.461
.523
.586
.648
.711
.773
.836
SMLS100-(*)06
NAS 1921(*)06
Length Max.
F Max.
.418
.446
.541
.666
.791
.916
1.041
1.166
1.291
1.416
1.541
.287
.350
.412
.475
.537
.600
.662
.725
.787
.850
.912
.500
.571
.696
.821
.946
1.071
1.196
1.321
1.446
1.571
1.696
SMLS100-(*)08
NAS 1921(*)08
Length Max. F Max.
.427
.460
.522
.585
.647
.710
.772
.835
.897
.960
1.022
1.085
-06
.100/.125
B Material Code
Aluminum Blind Rivets
Sleeve
Spindle
Lock collar
5056 Aluminum
2024 Aluminum
5056 Aluminum
Sleeve
Spindle
Lock collar
None
Chem. Treatment Per MIL-C-5541
None
C or EU Material Code
A286 CRES Blind Rivets
Component Material
A286 Cres
A286 Cres
A286 Cres
Component Finish or Surface Treatment
Passivated
Passivated
Passivated
For other finish options refer to, How to Order UNIMATIC Blind Rivets Page 18
M Material Code
MONEL Blind Rivets
MONEL Per QQ-N-281
A286 Cres
A286 Cres
None
Passivated
Passivated
.637
.762
.887
1.012
1.137
1.262
1.387
1.512
1.637
1.762
1.887
2.012
Sleeve Code:
Blank For 5056
Code C For A-286
Code M For Monel
Manufacturers
Identification
Length
(C)
Grip
Installed Rivet
Part
Number
SMLSP-(*)04-(**)
NAS1919 (*)04S(**)
SMLSP-(*)05-(**)
NAS1919 (*)05S(**)
SMLSP-(*)06-(**)
NAS1919 (*)06S(**)
SMLSP-(*)08-(**)
NAS1919 (*)08S(**)
Size
1/8
-04
5/32
-05
3/16
-06
1/4
-08
Grip Number
Rivet Nominal
Diameter
A Dia.
+.003 -.001
.125
.125
.156
.156
.190
.187
.250
.250
B Dia.
.250
.012
.312
.016
.375
.019
.500
.025
(C) Ref.
Head Height
G Min.
Dimension
.054
.788
.067
.788
.080
.788
.107
1.000
(*) Indicates material code letter. (**) Indicates grip length number.
Grip
No.
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
Min.
Max.
SMLSP-(*)04
NAS1919(*)04
Length Max.
F Max.
Length Max.
F Max.
.171
.198
.260
.323
.385
.448
.510
.573
.635
.698
.760
.298
.338
.443
.568
.693
.818
.943
1.068
1.193
1.318
1.443
.193
.227
.273
.336
.398
.461
.523
.586
.648
.711
.773
.836
.356
.378
.478
.602
.727
.852
.977
1.102
1.227
1.352
1.477
1.602
-04
.020/.035
.025/.062
Diameters
-05
.025/.045
.031/.062
NOTE A
SMLSP-(*)05
NAS1919(*)05
SMLSP-(*)06
NAS1919(*)06
SMLSP-(*)08
NAS1919(*)08
Length Max.
F Max.
.251
.287
.350
.412
.475
.537
.600
.662
.725
.787
.850
.912
.431
.526
.651
.776
.901
1.026
1.151
1.276
1.401
1.526
1.651
1.776
Length Max.
F Max.
.335
.397
.460
.522
.585
.647
.710
.772
.835
.897
.960
1.022
1.085
.606
.731
.856
.981
1.106
1.231
1.356
1.481
1.606
1.731
1.856
1.981
2.106
-06
.037/.062
B Material Code
Aluminum Blind Rivets
Sleeve
Spindle
Lock ring
5056 Aluminum
2024 Aluminum
5056 Aluminum
Sleeve
Spindle
Lock ring
None
Chem. Treatment Per MIL-C-5541
None
C or EU Material Code
A286 CRES Blind Rivets
Component Material
A286 Cres
A286 Cres
A286 Cres
Component Finish or Surface Treatment
Passivated
Passivated
Passivated
For other finish options refer to, How to Order UNIMATIC Blind Rivets Page 18
M Material Code
MONEL Blind Rivets
MONEL Per QQ-N-281
A286 Cres
A286 Cres
None
Passivated
Passivated
Sleeve Code:
Blank For 5056
Code C For A-286
Code M For Monel
Length
Manufacturers
Identification
(C)
Grip Number
Installed Rivet
Part
Number
Size
Rivet Nominal
Diameter
A Dia.
+.003/-.001
B Dia.
.004
(C) Ref.
Head Height
G Min.
Dimension
OSMLS100-(*)04-(**)
OSMLS100-(*)05-(**)
OSMLS100-(*)06-(**)
1/8 (04)
5/32 (05)
3/16 (06)
.140
.173
.201
.140
.173
.201
.225
.286
.353
.035
.048
.063
.788
.788
.788
OSMLS100-(*)08-(**)
1/4 (08)
.266
.266
.476
.088
1.000
Grip
(*) Indicates material code letter . (**) Indicates grip length number.
No.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
Min.
OSMLS100-(*)04
Max.
F Max.
(Length)
F Max.
.213
.260
.323
.385
.448
.510
.573
.635
.698
.760
.342
.391
.516
.641
.755
.891
1.016
1.141
1.266
1.391
.238
.263
.336
.398
.461
.523
.586
.648
.711
.773
.836
.418
.446
.541
.666
.791
.916
1.041
1.166
1.291
1.416
1.541
NOTE A
OSMLS100-(*)05
(Length)
-04
.057/.078
.079/.125
Diameters
-05
.075/.100
.100/.125
OSMLS100-(*)06
(Length)
F Max.
.287
.350
.412
.475
.537
.600
.662
.725
.787
.850
.912
.500
.571
.696
.821
.946
1.071
1.196
1.321
1.446
1.571
1.696
OSMLS100-(*)08
(Length)
F Max.
.427
.450
.522
.585
.647
.710
.772
.835
.897
.960
1.022
1.085
.637
.762
.887
1.012
1.137
1.262
1.387
1.512
1.637
1.762
1.887
2.012
-06
.100/.125
B Material Code
Aluminum Blind Rivets
Sleeve
Spindle
Lock collar
5056 Aluminum
2024 Aluminum
5056 Aluminum
Sleeve
Spindle
Lock collar
None
Chem. Treatment Per MIL-C-5541
None
C or EU Material Code
A286 CRES Blind Rivets
Component Material
A286 Cres
A286 Cres
A286 Cres
Component Finish or Surface Treatment
Passivated
Passivated
Passivated
For other finish options refer to, How to Order UNIMATIC Blind Rivets Page 18
M Material Code
MONEL Blind Rivets
MONEL Per QQ-N-281
A286 Cres
A286 Cres
None
Passivated
Passivated
Sleeve Code:
Blank For 5056
Code C For A-286
Code M For Monel
Manufacturers
Identification
Length
Part
Number
OSMLSP-(*)04-(**)
OSMLSP-(*)05-(**)
OSMLSP-(*)06-(**)
OSMLSP-(*)08-(**)
Grip
Size
1/8 (04)
5/32 (05)
3/16 (06)
1/4 (08)
Rivet Nominal
Diameter
.140
.173
.201
.266
(C)
Grip Number
A Dia.
+.003 -.001
.140
.173
.201
.266
B Dia.
.250 .012
.312 .016
.375 .019
.500 .025
(C) Ref.
Head Height
.054
.067
.080
.107
G Min.
Dimension
.788
.788
.788
1.000
Installed Rivet
(*) Indicates material code letter. (**) Indicates grip length number.
Grip Range
OSMLSP-(*)04
OSMLSP-(*)05
OSMLSP-(*)06
OSMLSP-(*)08
No.
Min.
Max.
Length
F Max.
Length
F Max.
Length
F Max.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
(1)
.063
.126
.188
.251
.313
.376
.438
.501
.563
.626
.688
.751
.813
.062
.125
.187
.250
.312
.375
.437
.500
.562
.625
.687
.750
.812
.875
.198
.260
.323
.385
.448
.510
.573
.635
.698
.760
.338
.443
.568
.693
.818
.943
1.068
1.193
1.318
1.443
.227
.273
.336
.398
.461
.523
.586
.648
.711
.773
.836
.378
.478
.602
.727
.852
.977
1.102
1.227
1.352
1.477
1.602
.251
.287
.350
.412
.475
.537
.600
.662
.725
.787
.850
.912
.431
.526
.651
.776
.901
1.026
1.151
1.276
1.401
1.526
1.651
1.776
Length
F Max.
.335
.397
.460
.522
.585
.647
.710
.772
.835
.897
.960
1.022
1.085
.606
.731
.856
.981
1.106
1.231
1.356
1.481
1.606
1.731
1.856
1.981
2.106
( 1 ) Minimum grip for -04 diameter is .025. For -05 diameter is .031. For -06 diameter is .037 .
B Material Code
Aluminum Blind Rivets
Sleeve
Spindle
Lock collar
5056 Aluminum
2024 Aluminum
5056 Aluminum
Sleeve
Spindle
Lock collar
None
Chem. Treatment Per MIL-C-5541
None
C or EU Material Code
A286 CRES Blind Rivets
Component Material
A286 Cres
A286 Cres
A286 Cres
Component Finish or Surface Treatment
Passivated
Passivated
Passivated
For other finish options refer to, How to Order UNIMATIC Blind Rivets Page 18
M Material Code
MONEL Blind Rivets
MONEL
A286 Cres
A286 Cres
None
Passivated
Passivated
10
Head Markings
Rivet heads carry the following Identification marks:
The special H as manufacturers identification
symbol.
A material code letter.
Aluminum rivets = no letter.
Monel rivets = letter M.
A-286 rivets = letter C.
A grip identification number.
Grip range = nominal grip +0/-.063
Example: 4 grip ranges from .250 to .188.
Minimum
Gr ip
M a x im u m
Grip
Huck
S ym b ol
G rip
N u m b er
Sleeve
Material
Code
Grip Gauging
Correct gauging of grip thickness will help to
insure sound rivet installations. Huck offers
grip measurement gages, which help assure
proper fastener grip selection. Huck Gage
#105093 (Red letters only) is configured to
11
Mechanical Performance
Nominal Rivet
Diameter
1/8 (04)
5/32 (05)
3/16 (06)
1/4 (08)
Code B
Aluminum Alloy
325
490
715
1200
Nominal Rivet
Diameter
1/8 (04)
5/32 (05)
3/16 (06)
1/4 (08)
Nominal Rivet
Diameter
1/8 (04)
5/32 (05)
3/16 (06)
1/4 (08)
Code B
Aluminum Alloy
125
200
290
510
Code C
A286 CRES
675
1050
1500
2600
Code C
A286 CRES
200
320
465
815
Gap
.010
.015
.020
.025
Alum Code B
10
15
20
30
A-286 Code C
15
22
30
45
12
13
Static joint strength of nominal diameter flush head. MLS100 / NAS1921 Blind Rivets
tested in Clad 7075-T6 Aluminum Sheet.
Ultimate Strength
Fastener Type
Fastener Material
Fastener Dia.
Sheet Thickness
.040
.050
.063
.071
.080
.090
.100
.125
.160
.190
Rivet Shear Strength
SMLS100-B/NAS1921B
Aluminum Alloy Rivets
1/8
5/32
3/16
(.130)
(.162)
(.194)
171
232
313
360
416
477
494
495
267
366
427
498
571
647
755
755
411
484
566
658
748
978
1090
1090
SMLS100-M/NAS1921M
MONEL Rivets
1/8
5/32
3/16
(.130)
(.162)
(.194)
SMLS100-EU/NAS1921C
A286 Rivets
1/8
5/32
3/16
(.130)
(.162)
(.194)
595 a
732 a
816 a
913 a
946 a
980 a
1020
612 a
749 a
831 a
923 a
1110 a
1090 a
1020
927 a
1035 a
1158 a
1289 a
1415 a
1525 a
1565 a
1565
1400 a
1570 a
1720 a
2055 a
2245 a
2260
2260
956 a
1060 a
1180 a
1305 a
1435 a
1670 a
1090
1670
365
466
528
598
639
686
804
571
649
737
835
931
1065
.042
.055
1450
1605
1755
2130
2400
a
a
a
a
a
2400
Yield Strength
.040
.050
.063
.071
.080
.090
.100
.125
.160
.190
Head Height (Ref.)
110
161
247
303
354
373
393
.042
171
254
315
395
484
549
610
.055
270
330
399
506
611
803
906
.070
354
447
504
569
607
626
686
.042
554
625
707
796
885
972
1080
.055
843
952
1060
1265
1430
1540
.070
873
990
1105
1325
1605
.070
Notes:
Data for Aluminum alloy blind rivets taken from MIL-HDBK-5G Chapter 8, page 8-67.
Data for Monel blind rivets taken from MIL-HDBK-5G Chapter 8, page 8-65.
Data for A286 CRES blind rivets taken from MIL-HDBK-5G Chapter 8, page 8-63.
Data above double line is knife edge condition.
Values identified with the letter (a) have a yield strength less than 2/3 of the indicated ultimate value.
Yield values are based on permanent set at 4% of nominal diameter.
Comment :
No comprehensive joint data is published for protruding head rivets. The rationale is that flush head allowables can be used for
reference. Actually, joint capabilities for protruding head rivets are significantly higher at the thin end of the structure profile, up to
perhaps .070 or .080 sheet thickness.
Installed Weight
The installed weights listed in the tables below are approximate and based on actual
weight of one or more production lots, averaged and rounded to the nearest 1/100
of a pound per thousand pieces.
Protruding Head, Unimatic Blind Rivets (weight in lbs./1000)
NAS1919B ALUMINUM
Grip
Length
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
1/8 (04)
Dia
0.38
0.45
0.52
0.59
0.66
0.73
0.80
0.87
0.94
5/32 (05)
Dia
0.59
0.72
0.85
0.98
1.11
1.24
1.37
1.50
1.63
1.76
1.89
2.02
2.15
NAS1919M MONEL
3/16 (06)
Dia
1/4 (08)
Dia
1.27
1.44
1.62
1.80
1.98
2.16
2.34
2.52
2.70
2.88
3.06
3.24
3.42
3.60
3.78
3.79
4.07
4.34
4.63
4.91
5.19
5.47
5.75
6.03
6.31
6.59
6.87
7.15
7.43
10.30
11.34
12.39
13.43
14.47
15.52
16.56
17.61
18.65
19.69
20.74
21.78
22.83
23.87
1/8 (04)
Dia
1.12
1.29
1.53
1.77
2.01
2.25
2.49
2.73
2.97
5/32 (05)
Dia
2.02
2.36
2.73
3.10
3.47
3.84
4.21
4.58
4.95
5.32
5.69
6.06
6.43
3/16 (06)
Dia
1/4 (08)
Dia
3.83
4.36
4.83
5.33
5.83
6.33
6.82
7.32
7.82
8.32
8.81
9.31
9.81
10.30
10.80
9.29
10.17
11.11
12.01
12.92
13.82
14.73
15.64
16.55
17.46
18.36
19.27
20.18
21.09
NAS1921M MONEL
3/16 (06)
Dia
1/4 (08)
Dia
0.98
1.16
1.34
1.52
1.70
1.88
2.06
2.24
2.42
2.60
2.78
2.96
3.14
3.32
2.59
2.87
3.15
3.43
3.71
3.99
4.27
4.55
4.83
5.11
5.39
5.67
5.95
8.04
9.09
10.13
11.18
12.22
13.26
14.31
15.35
16.40
17.44
18.48
19.53
20.57
1/8 (04)
Dia
0.79
1.03
1.27
1.52
1.76
2.00
2.24
2.48
5/32 (05)
Dia
1.46
1.93
2.20
2.60
2.97
3.34
3.71
4.08
4.45
4.82
5.19
5.56
3/16 (06)
Dia
1/4 (08)
Dia
2.85
3.37
3.90
4.42
4.94
5.46
5.98
6.51
7.03
7.55
8.07
8.59
9.12
9.64
7.21
8.15
9.08
10.02
10.96
11.90
12.84
13.77
14.71
15.65
16.59
17.53
18.46
14
15
Hole Preparation
Drill sizes should be chosen to generate holes within the diameters recommended in the table below. If
holes are drilled at the low limit, or if sealant is used in assembly, spindles sometimes break low and
installations are not complete. An easy remedy is to drill the holes slightly larger (within the recommended limits). This provides a little extra space for sealant trapped in the hole.
Hole Preparation
Nominal Dia. Rivets
Rivet
Diameter
-4
-5
-6
-8
Recommended
Hole Limits
.129/.132
.160/.164
.192/.196
.256/.261
Recommended
Drill Size
#30; 3.3mm
#20; 4.1mm
#10; 4.9mm
F
Recommended
Drill Size
#27; 3.7mm
#16; 4.5mm
#5; 5.25mm
na
Countersink Diameter
Recommended
Csink Diameter (Note)
.222/.228
.283/.289
.350/.356
.472/.480
The position of the spindle break and the lock collar provide important information about
the quality of the installation. The table below shows the limits published in the NAS1900
procurement specification. Spindle and collar flushness per this table indicate good
installations, which meet mechanical performance requirements of NAS1900.
Stem Protrusion Limits
Rivet
Diameter
A Dimension For
Flush Monel & A-286 Rivets
A Dimension
For All Other Rivets
Lock Collar
Position
-04
-05
-06
-08
+.010/-.005
+.010/-.005
+.010/-.005
+.015/-.005
+.018/-.008
+.022/-.010
+.025/-.012
+.032/-.016
Spindle Below
Sleeve Head
Tr o u b l e S h o o t i n g S u g g e s t i o n s
Problem
Possible Cause
Remedy
Oversize hole
16
Short
99-2724
Standard
99-2725
Long
99-2726
-05
-06
99-2730
99-2736
99-2731
99-2737
99-2732
99-2738
Short
99-2724
Standard
99-2725
Long
99-2726
-05
-06
-08
99-2730
99-2736
99-2742
99-2731
99-2737
99-2743
99-2732
99-2738
99-2744
Long
99-2747
Short
99-2745
Model 2012
P n e u d r a u l i c To o l
Rivet Dia.
-08
99-3467
90 Angle Nose
O f f s e t To o l i n g
H y d r a u l i c P o w e r To o l M o d e l 2 0 6 - 3 7 5
Rivet Dia.
-04
1 1/4 Offset
99-1715
1 7/8 Offset
99-1715-1
-05
-06
99-1716
99-1717
99-1716-1
99-1717-1
17
99-3466
Offset Nose
99-3458-202
99-3459-202
Heavy Duty
Heavy Duty
Offset 2 Jaw
90 Angle Nose
99-3466
99-3467
Std Duty
Std Duty
Step One
Place drill bushing from removal kit
so that it rests squarely on lock
collar. Using a drill from the proper
removal kit drill at a 1250 RPM
maximum to lock collar depth.
Step Two
Position pin punch from proper
removal kit in drilled area and drive
out remaining pin. Remove any lock
ring remaining in the sleeve head with
the pin punch.
Pin-drill
Diameter Depth
.081 Dia., .040 Deep
.1015 Dia., .050 Deep
.120 Dia., .060 Deep
.159 Dia., .070 Deep
Step Three
Using adjustable micro limit tool in
removal kit adjust cutter to depth of
fastener head. Micro-limit tool is fitted
with a anti-rotation cap to hold sleeve
head during cutting operation.
Pin Punch
Diameter
1/16
3/32
3/32
1/8
Sleeve Punch
Diameter
1/8
5/32
3/16
1/4
Step Four
Using the
correct size
sleeve punch from the kit push out
the remaining sleeve. Use the same
punch to lift out the remaining head
piece.
H o w To O r d e r U n i m a t i c B l i n d R i v e t s
Huck Part Numbers
Coating codes
No code indicates uncoated
A Indicates Aluminum Coating per
NAS4006
FC Indicates Chemical Film per
MIL-C-5541
W Indicates Cadmium Plating per
QQ-P-416
U Optional Drive Washer
Fastener Grip Length
Shown in 1/16 (.062) inch increments
Installation Method
S Indicates Single Action Installation
Indicates double action installation
Fastener Diameter
Shown in 1/32 (.031) inch increments
Material Code
B Indicates 5056 Aluminum
C Indicates A-286 CRES
M Indicates MONEL
Basic Part Number
NAS 1919 Indicates Protruding Head
Blind Rivet
NAS 1921 Indicates Flush Head
Blind Rivet
S MLSP B 04 04 FCU
Coating codes
No code indicates uncoated
A Indicates Aluminum Coating per
NAS4006
FC Indicates Chemical Film per
MIL-C-5541
C Indicates Cadmium Plating per
QQ-P-416
EL Indicates Dry Film Lube
(Dicronite DL-5)
U Optional Drive Washer
Fastener Grip Length
Shown in 1/16 (.062) inch increments
Fastener Diameter
Shown in 1/32 (.031) inch increments
Material Code
B Indicates 5056 Aluminum
EU Indicates A-286 CRES
M Indicates MONEL
Basic Part Number
MLSP Indicates Protruding Head
Blind Rivet
MLS100 Indicates Flush Head
Blind Rivet
OSMLSP Indicates Oversize
Protruding Head
OSMLS100 Indicates Oversize
Flush Head
Installation Method
S Indicates Single Action Installation
NO CODE Double Action Installation
18
PO Box 2270
One Corporate Drive
Kingston, NY 12401
Phone: 800 635 8320
Phone: 914 331 7300
Fax: 914 334 7333
Telex: 926486
TM
TM
TM
Huck S.A.
Clos DAsseville BP4
95450 Us Par Vigny
France
Phone: 33 1 3027 9500
Fax: 33 1 3466 0600
NOTICE: The information contained in this brochure is only for general guidance with regard to properties of the
products shown and/or the means for selecting such products, and is not intended to create any warranty, express,
implied or statutory, all warranties are contained only in Hucks written quotations, acknowledgements and/or
purchase orders. It is recommended that the user secure specific, up-to-date data and information regarding each
application and/or use of such products.