Академический Документы
Профессиональный Документы
Культура Документы
OPERATING PRINCIPLE
The roving bobbins (1) are inserted in holders (3) on the creel.
Guide bars (4) guide the rovings (2) into the drafting system (5), where they are drawn to
their final count.
The drafting system is at an angle of 45-60 and is one of the most important units on the
machine, since it exerts a very considerable influence on the uniformity of the yarn in
particular.
After the resulting thin strand of fibers (6) leaves the delivery roller, the twist necessary
for imparting strength is provided by spindle (8) rotating at high speed.
In the process each rotation of the traveller on the spinning ring (10) produces a twist in
the yarn.
Ring traveller (9) is also necessary for taking up this yarn onto a tube mounted on the
spindle. This traveller moves on a guide rail (i.e. Ring) around the spindle. The ring
traveller has no drive of its own, it is dragged with spindle (8) via the yarn attached to it.
2
OPERATING PRINCIPLE
The rotation of the ring traveller lags somewhat behind that of the spindle due to the
relatively high friction of the ring traveller on the ring and the atmospheric resistance of
the traveller and the thread balloon between yarn guide eyelet (7) and traveller (9).
This difference in speed between the spindle and the traveller results in the thread being
wound onto the tube.
In contrast to the roving frame, the ring spinning machine spindle operates with at higher
speed than the traveller (9).
The yarn is wound up into a cylindrical cop form by raising and lowering of the rings,
which are mounted on a continuous ring rail.
The layer traverse of the ring rail is also less than the full winding height of the tube. The
ring rail therefore has to be raised slightly (shift traverse) after each layer has been
wound.
3
LIMITATIONS
Piecing of the yarn is difficult (delivery rate cant be increased due to piecing).
Lower yarn strength in the region of spinning triangle.
There is a tendency of balloon formation.
Burning of traveller at higher speed because of fractional heating.
Productivity is limited, mainly because of traveller speed.
The process of making yarn is longer than other means, as elimination of stages is not possible.
This machine has a significant cost factors.
MODES OF IMPROVEMENT
Development of improved ring and traveller, which now seems to be very difficult.
Increase in Traveller speed (35-40m/ sec) by reducing friction.
Automatic doffing
Number of spindle per machine should increase in machine length.
End breakage rate reduction
Improvement of roving quality
Linking of ring with the winding machine (Link coner)
Roving stop devices (Reduced waste/Pneumaphil)
Automation in the field on:
Roving bobbin
Bobbin transport
Bobbin change
5
ROLLER DEFLECTION
Roller deflection is considered almost necessary in modern ring frames.
It gives a V shape to the drafting systems (SKF PK- 2020/2025/2055/2035/2065)
Front top roller should be shifted towards the front of machine and the middle top roller should be shifted
to towards the back of the machine. This shifting must be in the range of 1-4mm.
Advantages:
End breakage rate decreases
Twist flow is improved
Quality of running of top roller will be smooth.
Spinning geometry (triangle) will be reduced
Fiber support (surface support) will increase because of increasing contact of fibre with roller surface.
To increase fibre support and to increase break draft, the top back roller can also be shifted towards back of
machine.
6
ROLLER DEFLECTION
This can take place in the form of deflection around rollers (b), single aprons (c) or double aprons (d). New
ring spinning machine drafting systems are equipped with double aprons, as well as deflection around rollers
(b).
10
11
THREAD GUIDE
Fitted immediately over the spindle, the thread guide (Lappet guide)
guides the yarn centrally over the center axis of the spindle.
The thread guide consists of wire eyelet (o) and thread board (k). The
eyelet is mounted adjustably in the thread board (fitted on a thread
guide rail) to enable it to be centred.
The rail can be raised and lowered with the thread guides. While cops
are being wound it performs the same movements as the ring rail, but
with a smaller traverse height:
Continuous raising and lowering during layering
Continuous lift by small amounts as switching traverse
14
SEPARATOR PLATE
It is a protective device, made of Plastic or metallic (Al) and is
used to keep neighboring yarn (more specifically yarn
balloons) separate to avoid any chance of collision.
In case of an ends down, broken end of the yarn can whirl
around the swiftly rotating spindle and can collide with the
neighbouring yarn balloons and can cause a chain of ends
down.
16
SPINDLE DRIVE
50-80% of the total power of ring frame is utilized in spindle drive.
TAPE DRIVE
Tape drive technology is most famous and widely used as a mean to provide drive to the spindle.
Tape drive may be of two types; (w.r.t. Number of spindles)
Individual spindle driving tape
Tin rollers take drive from the main motor and deliver to 4 spindles by single tape through jockey pulley.
Tape drive may be of two types; (w.r.t. Tape material)
Cotton tape (endless, soft, more wear, high elasticity, spindle to spindle variation, less age/ lift time)
Synthetic tape (less wear, less elasticity, high life span but costly)
17
SPINDLE DRIVE
ADVANTAGES OF TAPE DRIVE:
It is more universal
If the tape is broken due to any reason, only 4 spindles will be stopped, less production loss relatively.
DISADVANTAGES:
It will cause the whole frame to vibrate and consume unnecessary energy.
TENSION IN TAPE IS VERY IMPORTANT:
Level of tension should be correct
There should be minimum variation in tension.
If it is not, cause streaks/ barness fault in fabric.
RING
It acts as a guiding and running circular track of the traveller.
Adaptor (spring) is used to tight the ring on the ring rail from the lower side. It must not loose.
Three important things related to ring are:
Accurate manufacturing
Optimum selection
Proper application
QUALITY PARAMETERS:
Material of ring
Surface characteristics
Forms of both elements (Ring w.r.t. Traveller)
Wear resistance
Level of smoothness of running
Running in condition (breaking time)
Fibre lubrication (ring and traveller are metallic, rubbing with each other, wear, so lubrication is necessary)
22
RING
RING TYPES:
1. With respect to lubrication
2. With respect to number of sides
3. Size of ring
4. Flange number
5. Profile of flange
6. With flange and flange-less ring
7. Old ring
8. New ring
(high performance ring on high performance ring frame with H.F traveller)
23
TYPES OF RING
LUBRICATION:
LUBRICATED RING:
Normally used for woolen and worsted spinning.
Only/ sometimes they are also used on doubling frame for doubling and plying, folding and cabling.
Also known as grooved ring, (it has a groove in the internal side for lubrication)
Not used for making single yarns
24
TYPES OF RING
NUMBER OF SIDES:
SINGLE FLANGED
Also known as plane ring
Used for short staple spinning
DOUBLE FLANGED:
Also known as reversible ring
Used in old days, not used now- a- days
both sides can be use
Grip is not proper
25
TYPES OF RING
FLANGE NUMBER:
Smallest size
0.5
1.5
2.5
Flange diameter
(mm)
2.3
2.6
3.2
3.7
4.1
4.36
4.76
6.3
26
TYPES OF RING
SIZE OF RING:
Popular sizes (internal diameter) of ring are 36, 38, 40, 42, 45, 48, 51, 54 mm depending upon the
yarn count.
Mentioned sizes are used for making single yarn.
For double yarn ring diameter ranges from 2-4 that runs at much lower speed.
MOST IMPORTANT FACTORS TO DETERMINE THE SIZE OF RING:
Angel of yarn pull
Traveller speed
27
TYPES OF RING
FLANGE PROFILE:
Shape of the upper part of the ring is known as profile.
1. Flat ring (especially compatible for elliptical traveller, used for finer yarn
Anti-wedge
Low crown
2. Conventional ring
28
TYPES OF RING
ANTI-WEDGE RING:
High performance anti-wedge ring have offset part on which traveller moves.
In this case the flange inner side is enlarged and also flattened from the upper side. This change will
permit the use of travellers with a low center of gravity and precisely adopted in case of elliptical traveller.
These rings can operate at high speed and are preferred for making finer count.
Traveller life will be more. Ring wear will be less.
The spread of load will be better and also heat dissipation will be more.
29
TYPES OF RING
LOW CROWN RING:
Curvature of upper surface has been flattened giving more space for passage of yarn so that curvature
of traveller is also been reduced and center of gravity will be lowered.
On this ring all type of traveller can be used except elliptical.
RING ALIGNMENT:
1. Horizontal
2. Vertical (ear shaped) used in doubling frame
3. Inclined
RING SURFACE:
1. Solid surface ring
2. Porous centered surface ring
30
MATERIAL OF RING
MATERIAL TYPE:
1. Cardio nitrated steel
(most popular)
2. Chrome steel
3. Nitrated steel
(2 M.P)
(rarely used)
(rarely used)
nd
Traveller
Surface of the ring should be very hard, smooth but not be over smooth.
Wax in cotton melt at higher speed, due to high smoothness it does not retain on the ring surface. This
film disappears.
However it is necessary to get higher speed of traveller.
31
MATERIAL OF RING
RUNNING IN OF RING: (breaking time)
While using a new ring:
Use the lower traveller number than required.
Decrease the speed of spindle
Lubrication film must not be completely removed
The spindle speed should be gradually increased in steps when installing new ring, but not in sharp steps.
This will increase the life of ring.
Burnt traveller should not be allowed to run for long periods to avoid the spoilage of ring surface
(oxidized surface of traveller will be deposited on the flange)
32
TRAVELLER
Traveller is a C shaped tiny compound, running on the ring flange.
It insert the twist in yarn in association with spindle rotation.
The level of twist depends upon the speed of traveller
Nominal twist
Actual twist
Spindle speed is constant but traveller speed varies, during the formation of different package stages
(base, body, shoulder), but it is ignorable. However change in IPI of the yarn.
FUNCTIONS OF TRAVELLER:
Winding
Guiding towards the surface of package
To control the tension in yarn
33
TRAVELLER
There are so many types of traveller due to enormous number of yarns varying in following characteristics;
Coarse or fine
Thin or thick
Hairy and smooth
Single or double
Compact or voluminous
Strong (combed/ blended/ polyester) or weaker (Carded)
Natural or synthetic
Spindle speed
Ring diameter
Ring type
34
TRAVELLER
CLASSIFICATIONS
1. With respect to shapes
a) C shape
(kidney shape)
b) Flat
c) Elliptical
(oval)
d) N shaped
2. Height of bow
Horizontal
Vertical (ear shape)
3. Wire profile
4. Traveller mass
5. Type of material
6. Type of surface finish of traveller
35
TRAVELLER
BASIC REQUIREMENTS
Heat dissipation
Sufficient thread space
Matching of size and shape of the traveller with the flange on which it is applied.
Single contact surface (Less friction, less wear)
Flat bow
Good sliding property
36
TRAVELLER
CENTIFUGAL FORCE BETWEEN RING AND TRAVELLER:
Centrifugal force
(35 N/mm )
Friction
Heat
TRAVELLER
TYPES OF SHAPE OF TRAVELLER:
1. C shaper traveller:
Conventional type, Preferred for bulky yarn
Low End breakage rate
3. Elliptical
4. N travellers:
5. Ear shaped traveller (vertical traveller)
6. SU traveller:
7. Kidney shaped traveller:
Preferred for fine and medium not for coarser count.
38
TRAVELLER
WIRE PROFILE:
Three cross sections are primarily important:
Round
Flat
Semi circular
ROUND:
Preferred for long fibres (wool, synthetic)
FLAT:
Preferred for short fibre(cotton)
SEMI CIRCULAR: (semi round)
Large contact surface will be more useful for higher speed.
39
TRAVELLER
40
TRAVELLER
TRAVELLER NUMBERING: (MASS OF TRAVELLER)
In old systems (Indirect System) weighing the 10 travellers in grains
In Modern system (Direct System) weighing the 1000 travellers in grams
POSITIVE GROUP:
(Light travellers)
0, 1, 2, 3, 4, 5, . 75
(Heavier traveller)
(Heavier travellers)
NEGATIVE GROUP:
(Light travellers)
Traveller mass is very much concerned with the yarn tension. More mass of traveller, more will be the
yarn tension.
Compactness and density of package is also related to traveller mass. More mass more compactness
and more will be the package density and vice versa.
41
TRAVELLER
SURFACE FINISH:
Electroplating:
Coating of one or two metallic layers. E.g. nickel and silver on steel
Chemical treatment:
On surface to reduce the frictional effect
Pitting:
The process of creating small holes on the surface
Finishing components diffused into traveller surface, E.g.
Sapphire traveller
Starlet
(bracker component)
Titan
(bracker component)
42
TRAVELLER
TRAVELLER SPEED:
Two main variable affecting traveller speed
Ring diameter
Spindle speed
43
TRAVELLER
FACTORS AFFECTING TRAVELLER SPEED
Traveller weight
Yarn tension
Smoothness of ring surface
Shape of traveller
Surface finish of ring and traveller
Type of build (in case of cop build higher speed can be possible)
44
46