Академический Документы
Профессиональный Документы
Культура Документы
4.3.9
Mechanical Anchoring Systems
Bolt
Diameter
in. (mm)
( 6.4)
( 7.9)
( 9.5)
(12.7)
(15.9)
(19.1)
3/16
1/4
5/16
3/8
1/2
5/8
Embedment
Depth
in. (mm)
( 4.8)
( 6.4)
( 7.9)
( 9.5)
(12.7)
(15.9)
1
1
1-1/4
1-1/2
2
2
(25)
(25)
(32)
(38)
(51)
(51)
Embedment
Depth
in. (mm)
1/4 (6.4)
5/16 (7.9)
3/8 (9.5)
1-1/8 (29)
1-1/4 (32)
1-1/2 (38)
Concrete2
2000 psi (13.8 MPa)
Tension
Shear
lb (kN)
lb (kN)
235 (1.0)
450 (2.0)
310 (1.4)
675 (3.0)
450 (2.0)
1000 (4.4)
Hollow C-90
Concrete Block 3,4
Tension
lb (kN)
200 (0.9)
335 (1.5)
470 (2.1)
Shear
lb (kN)
400 (1.8)
600 (2.7)
890 (4.0)
2 Refer to Kwik Bolt II data, in Section 4.3.3.3, page 167, for spacing and edge distance guidelines in Concrete.
4 Refer to HY 20 data, in Section 4.2.3.3, page 118, for spacing and edge distance
guidelines in Hollow Concrete Block.
Embed.
Depth2
in. (mm)
1/4 ( 6.4)
1 (25)
5/16 ( 7.9)
1 (25)
3/8 ( 9.5)
1-1/4 (32)
1/2 (12.7)
1-1/2 (38)
5/8 (15.9)
2 (51)
3/4 (19.1)
2 (51)
Edge
Distance
in. (mm)
4
12
4
12
4
12
4
12
4
12
4
12
(101)
(305)
(101)
(305)
(101)
(305)
(101)
(305)
(101)
(305)
(101)
(305)
Tension
lb (kN)
Shear
lb (kN)
290 (1.3)
305 (1.4)
385 (1.7)
500 (2.2)
435 (1.9)
725 (3.2)
605 (2.7)
710 (3.2)
840 (3.7)
865
1145
1050
1815
1050
1970
(3.8)
(5.1)
(4.7)
(8.1)
(4.7)
(8.8)
2 Embedment depth is measured from the outside face of the concrete masonry unit.
3 Values are for anchors located in the grouted cell, bed joint, cross web or any
combination of the above.
4 For anchors installed in the T joint or head joint reduce tension values by 20%.
5 Values for edge distances between 4 inches and 12 inches may be calculated by linear
interpolation.
7 Based on using a safety factor of 4.0.
1/4
5/16
3/8
1/2
( 6.4)
( 7.9)
( 9.5)
(12.7)
Bolt
Diameter
in. (mm)
3/16
1/4
5/16
3/8
(4.8)
(6.4)
(7.9)
(9.5)
Tension
lb (kN)
350
375
435
565
(1.5)
(1.7)
(1.9)
(2.5)
Shear
lb (kN)
305
560
800
1125
(1.4)
(2.5)
(3.5)
(5.0)
1 Values are for Lightweight, Medium Weight or Normal Weight concrete masonry units
conforming to ASTM C 90 with 2000 psi grout conforming to ASTM C 474.
Sleeve
Anchor Size
in. (mm)
( 6.4)
( 7.9)
( 9.5)
(12.7)
Embedment
Depth
in. (mm)
1
1
1-1/4
1-1/2
(25)
(25)
(32)
(38)
Tension
lb (kN)
295
345
375
435
(1.3)
(1.5)
(1.7)
(1.9)
Shear
lb (kN)
335
530
850
1230
(1.5)
(2.3)
(3.8)
(5.5)
US www.us.hilti.com
Canada www.ca.hilti.com
Hilti, Inc. (US) 1-800-879-8000 I Product Technical Guide 2004 I Hilti (Canada) Corporation 1-800-363-4458
191