Академический Документы
Профессиональный Документы
Культура Документы
Operation
The 23AA20 board has two galvanic isolated analog
output channels. Each of them can be configured individually to one of the following output current:
V
V
V
V
-5 mA...
-5 mA.....
-10 mA...
-20 mA...
0...+2.5 mA
0...+5 mA
0...+10 mA
0...+20 mA
Processing function
The I/O microcontroller (EAP Ein- Ausgabe-Prozessor / Input- output processor) controls the two digital
to analog converters. It converts the received output
value from CMU (CMU = communication unit) into
the D/A format and force an output conversion. The
output value keeps stable until a new value receives.
The output value is zero after power up, cold start or
warm start of the 23AA20.
Basic subrack only:
If the RTU560 is reset (by CMU reset button or on
command from CS) the 23AA20 board set the output
value negativ. This state is given until the reset button
is released or the CMU software enables the peripheral bus again. A positive output value of e.g. +10 mA
becomes -10 mA.
The last output value keeps set if the ST-LED is ON after normal operation.
= 4 mA
V 2000 (100 %) = 20 mA
The ouptut channel becomes a live zero channel after
it is parameterized by the CMU. Until that time the output has the default of 20 mA.
Settings
The jumper settings for channel 1 or channel 2 are described in table 1 or table 2.
Signalling
The board monitors and checks its functionality as
well as the dialog via the peripheral bus. Detected errors are indicated and/or transmitted by the board:
V by the red LED ST on the front plate
V by diagnostic messages
The ST LED indicates board errors or peripheral
bus errors.
The ST-LED indicates:
V board runs initialization procedure
V board is doing a cold- or warm start
V board has detected a memory error (RAM or
EPROM)
V micro controller faulty
V no dialog via the peripheral bus for at least 2
minutes. The board is not polled by the PBP of
CMU..
RTU560
ST
opto-
Micro
controller
output
memory
opto-
EPROM
output
age
current range
converter
channel 1
+ 15 V DC
0 V DC
- - 15 V DC
+/U
adjustment
volt- -
output
age
current range
0V
DC / DC
converter
b32
channel 1
ref.
Vcc
z32
adjustment
coupler
DC / DC
0V
+/U
IO11 +
IO10 -
volt-
ref.
output
memory
EAP
Vcc
coupler
RAM
IO21+
z30
IO20 -
b30
channel 2
+ 15 V DC
0 V DC
- - 15 V DC
channel 2
RTU560
Channel 1 jumper configuration
Jumper
2.5 mA
5 mA
10 mA
Jumper
X50 X51
X52
X53
X54
X55
X10
2.5 mA
5 mA
10 mA
20 mA
X60 X61
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
3 2 1
3 2 1
3 2 1
1 2 3
1 2 3
X62 X63
3
2
1
3
2
1
3
2
1
3
2
1
X64 X65
3
2
1
3
2
1
3
2
1
3
2
1
1 2 3
3 2 1
3 2 1
X11
3 2 1
3 2 1
3 2 1
red
321
321
X11
X10
X64 X65
3
2
1
DC / DC DC / DC
converter converter
X62 X63
X60
X50
X51
R 50
123
X52
X53
123
3
2
1
R 60
X61
X54
X55
23TP21
R0031
R0011
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
19
18
17
19
18
23ET23
Sub-connector
z32
b32
RTU560
Signal identification
Meaning
Identification
IO11 +
Output channel 1 +
IO10 -
Output channel 1 -
IO21 +
Output channel 2 +
IO20 -
Output channel 2 -
ReRe
mark
d32
z30
b30
d30
z28
b28
d28
z26
b26
d26
z24
b24
d24
z22
A (Faston
6,3)
b22
d22
The pin configuration of 23ET23 subrack corresponds to the direct pin configuration of the board connector
TP21
ET23
RTU560
23AA20
23TP21
R 0031
1
D / A output
channel 1
Signalidentific.
Process
IO11 +
IO11 -
Unit 1
2
3
IO21 +
4
D / A output
channel 2
IO20 -
Unit 2
5
6
7
8
9
10
11
12
13
14
15
16
17
b22
d22
18
19
*
*
23TP21
R0031
23TP21
R0011
17
19
b22
18
17
d22
19
18
RTU560
RTU560
03/2001
Subject to alteration