Академический Документы
Профессиональный Документы
Культура Документы
00191.MAT.MEC.SDS
Rev. 6
June 1997
6
REV.
STIN
COMP.D
IMPI
CHECK.D
STIN
APPR.D
15.6..97
DATE
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 2
FOREWORD
Rev. 6
N sheets 9
June 1997
This specification has been restructured from conceptual and graphical point of
view as Company specification, its general revision has been performed in
accordance with CEE rules which require functional requirements evidence
and discriminating elements deletion.
In particular:
-
the specification does not take into account only one type of steel, but the
minimum mechanical properties has been fixed;
all the requirements already included in the required stan dards have been
cancelled.
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 3
CONTENTS
1
GENERAL
1.1
Scope
1.2
Normative references
1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
2.1
Operative environment
2.2
Functional requirements
2.2.1
Material requirements
2.3
Ergonomics
2.4
Safety
2.5
2.6
2.6.1
2.6.2
2.6.3
2.7
Documentation
2.7.1
Testing documentation
SUPPLEMENTARY ELEMENTS
3.1
3.1.1
Enclosures
MOD.MEC.PRV.107
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 4
GENERAL
1.1
SCOPE
This specification aims to defines the additional prescriptions to Code UNI EN
10028/3 for the supply of high class steel to be used for the fabrication of
pressure vessels handling hydrocarbons.
This specification regards steel plates in a thickness range from 16 mm to 100
mm.
This specification covers also the requirements for supply of materials to be
used in sour environment with H 2S.
1.2
Normative reference
1.2.1
1.2.2
EU 160
UNI EN 10028/3
UNI 3245
ISPESL
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 5
1.2.3
1.2.4
ASME Sect. V
Legislation
There is no legislation specifically applicable to the specification subject. In
geographic areas other than Italy local legislation shall be considered.
1.2.5
05489.MAT.COR.SPC
MOD.MEC.PRV.107
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 6
2.1
Operative environment
Requirements to be considered do not exist.
2.2
Functional requirements
2.2.1
Materials requirements
Materials shall be in accordance at least with the requirements specified by UNI
Code EN 10028/3.
Steel shall be ageing type resistant, it shall be killed with aluminium and should
have a fine grains structure.
The dimension of the ferritic grain shall comply with the requirements of UNI
Code 3245.
Alternative materials supposed as equivalent or better shall be submitted to
Company approval; the proposal shall be justified with comments and anyway
shall satisfy the additional requirements of this specification.
Carbon equivalent shall satisfy the requirements of the UNI Code EN 10028/3.
2.2.1.1
Mechanical properties
The mechanical properties shall be determined for each steel plate or part of
steel plate used for the equipment fabrication and shall comply with UNI Code
EN 10028/3.
The mechanical tests and the relevant samples marking .shall be carried out in
the presence of the Companys Inspector who shall have free entrance into the
places where the testing will be performed.
When heat treatment is requested after welding, the deviation minimum values
(from proportionality to 0.02% ) allowed according UNI Code 10028/3 shall
be found on the samples submitted a stress reliving treatment at 600C.
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 7
Heating and cooling velocity and permanence soaking time at stress reliving
temperature treatment shall be in compliance with ISPESL Codes, collection
S, chapter S 8.
2.2.1.2
2.2.1.3
Heat treatment
The steel plates shall be supplied after a proper normalisation heat treatment in
accordance with ISPESL Code collection S.
2.3
Ergonomics
Requirements to be considered do not exist.
2.4
Safety
Requirements to be considered do not exist.
2.5
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 8
2.6
2.6.1
2.6.2
2.6.3
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
00191.MAT.MEC.SDS
Rev. 5 June 1997
Sheet 9
2.7
Documentation
2.7.1
Testing documentation
Testing documentation which steel plate Contractor shall supply must include
at least the following informations:
-
SUPPLEMENTARY ELEMENTS
3.1
3.1.1
Enclosures
MOD.MEC.PRV.107
Il presente documento RISERVATO ed di propriet dell'AGIP. Esso non sar mostrato a Terzi n sar utilizzato per scopi diversi da quelli per i quali stato inviato.
This document is CONFIDENTIAL and the sole property of AGIP. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.