Академический Документы
Профессиональный Документы
Культура Документы
TABLE OF CONTENTS
Altitude Valve
210-01/610-01 Altitude Valve for One-Way Flow .........................................................................82
Air Release Valves
33A High Performance Combination Air Release & Vacuum Breaker Valve ..................................86
33B High Performance Combination Air Release & Vacuum Breaker Valve ..................................88
Check Valves
501A Wafer Swing Check Valves .................................................................................................96
580 Silent Wafer Check Valves - FM ...........................................................................................92
581 Silent Globe Check Valves - FM...........................................................................................96
582SWS Two Door Check Valves - FM .....................................................................................100
582W - 582 - 582G Two Door Check Valves - UL, FM.................................................................102
Pilot System Strainers & Restriction Assemblies ........................................................................104
Engineering Data..............................................................................................................................105
Flange Dimensions and End Details ..............................................................................................106
Warranty:Cla-Val Control Valves....................................................................................................107
Warranty:Cla-Val Roll Seal Valves .................................................................................................108
DESIGN
ASSE
SSED
UL
PUB
SINGAPORE
SUD
Industrie Service
MEA
APPROVED
Company Overview
Cla-Val Canada
Cla-Val UK
Cla-Val Europe
Switzerland
Cla-Val France
Cla-Val USA - Costa Mesa CA
Global Headquarters
Cla-Val Pacific
New Zealand
Global Capabilities
4
MEA
APPROVED
PUB
SINGAPORE
DESIGN
ASSE
SSED
100S/2100S
MODEL
Principle of Operation
On-Off Control
On-Off Control
Modulating
Control
Modulating Action
The valve holds any intermediate position
when operating pressures are equal above
and below the diaphragm. A Cla-Val modulating pilot control will allow the valve to
automatically compensate for line
pressure changes.
Specifications
PIPE PLUG
HEX NUT
COVER
Available Sizes
Pattern
Threaded
Flanged
Grooved End
Fluids
Globe
1" - 3"
1" - 36"
-40 to 180 F
Angle
1" - 3"
2" - 24"
PIPE PLUG
Cover Bolt
6" and Smaller
COVER BEARING
SPRING
STEM NUT
DIAPHRAGM WASHER
KO Anti-Cavitation
Trim Option
Pressure Ratings
Pressure Class
Flanged
Material
300
Class
End
Details
250
400
400
400
285
400
400
400
ASTM B62
225
400
400
400
Bronze
B16.24
DISC RETAINER
KO
SEAT
Grooved Threaded
ANSI
150
300
Standards* Class Class
*DIAPHRAGM
KO
DISC
GUIDE
*SPACER WASHERS
*DISC
DISC GUIDE
STEM
Seat Screw
8" and Larger
Note:
SEAT
SEAT O-RING
STUD
8" and Larger
BODY
Component
Ductile Iron
Available Sizes
114" - 36"
PIPE PLUG
(Globe or Angle)
Materials
Cast Steel
114" - 16"
Stainless Steel
NI. AL. Bronze
Type 316
Bronze
114" -16"
Super Duplex
Stainless Steel
114" -16"
114" -16"
114" -16"
Bronze
Monel
Super Duplex
Stainless Steel
*Repair Parts
Bronze is Standard
Stainless Steel is optional
Buna-N Rubber
Nylon Reinforced Buna-N Rubber
Stainless Steel
Purchase Specifications
The Model 100S/2100S shall be a hydraulically operated, diaphragm-actuated, globe or
angle pattern valve. It shall contain a resilient, synthetic rubber disc, having a rectangular
cross-section, contained on three and one-half sides by a disc retainer and disc guide,
forming a tight seal against a single removable seat insert. The diaphragm assembly, containing a valve stem, shall be fully guided at both ends by a bearing in the valve cover and
an integral bearing in the valve seat. This diaphragm assembly shall be the only moving
part and shall form a sealed chamber in the upper portion of the valve, separating operating
pressure from line pressure. The diaphragm shall consist of nylon fabric bonded with synthetic rubber and shall not be used as a seating surface. Packing glands or stuffing boxes
are not permitted and there shall be no pistons operating the valve or its pilot controls. All
necessary repairs shall be possible without removing the valve from the line. All materials
shall be compatible with seawater.
Valve shall be Model 100S/2100S manufactured by Cla-Val, Newport Beach, CA 92659-0325
5. Screwed or Flanged
6. Temperature and fluid to be handled.
7. Static and Flowing Line Pressure.
8. Body & Trim Material
9. Desired Options
10. When Vertically Installed
9
Functional Data
Inches
114
112
212
10
12
14
16
18
20
24
30
36
25
32
40
50
65
80
100
150
200
250
300
350
400
450
500
600
750
900
32
54
85
115
200
440
770 1245 1725 2300 3130 3725 5345 7655 10150 14020
7.7
13
20
28
48
106
185
Valve Size
CV
Factor
Model 100S/2100S
mm.
299
414
552
752
894
Angle Gal./Min.(gpm.) 27
Pattern Litres/Sec. (l/s.) 6.5
27
29
61
101
139
240
541
9950*
6.5
15
24
33
58
130
238
378
600
734
1008
2388
Feet (ft.)
Equivalent Globe
Pattern Meters (m.)
23
19
37
51
53
85
116
211
291
347
467
422
503
612
595
628
1181 2285
7.1
5.7
12
15.5
16
26
35
64
89
106
142
129
154
187
181
192
552
569
28
28
46
40
37
58
80
139
176
217
222*
238*
247*
372*
8.7
8.7
14
12
11
18
25
43
54
66
68
73
75
113
Globe Pattern
6.1
3.6
5.9
5.6
4.6
6.0
5.9
6.2
6.1
5.8
6.1
5.0
5.2
5.2
4.6
4.0
5.3
7.8
Angle Pattern
4.4
4.4
7.1
4.4
3.3
4.1
4.1
4.1
3.7
3.6
2.9
2.8
2.6
2.4
Fl. Oz
.02
.02
.02
.03
.04
.08
.17
.53
4.0
6.5
9.6
11
12
29
42
90
163
303
643
2.0
4.8
9.5
15.1
24.6
36.2
41.6
Length
of
Pipe
K
Factor
Litres
1.26 2.51
C V Factor
197
340
*Estimated
Where:
CV =
45.4 109.8
Q = CV
Q
P= C
V
K = 894d
2
P):
or
Cv
= Kd
K
L
Q
V
P
12 f
.4085 Q
V=
d2
Model 100-01 Flow Chart (Based on normal flow through a wide open valve)
Angle Valve Sizes (Inches)
11/4
11/2
11/4
11/2
2
2
21/2 3
21/2
4
4
6
6
10
10
12 14
12 14 16
16 18
20 24
24
30 36
100
80
60
40
30
20
10
8
6
4
3
2
1
1
10
20
30 40
60 80 100
200
Flow Rate
10
500
1000
gpm (water)
2000
5000
10,000
20,000
50,000 100,000
B (Diameter)
B (Diameter)
Dimensions 100S/2100S
H
Threaded &
Flanged
100S/2100S
Grooved
CC
(MAX)
(MAX)
Inlet
Outlet
Inlet
G
GG
GGG
1
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
EE
GGGG
D
DD
DDD
Inlet
A
AA
AAA
Inlet
DDDD
AAAA
1 1/4
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
1 1/2
2
2 1/2
3
4
6
8
10
12
14
16
7.25 9.38 11.00 12.50
8.50 9.38 11.00 12.00 15.00 20.00 25.38 29.75 34.00 39.00 41.38
9.00 10.00 11.62 13.25 15.62 21.00 26.38 31.12 35.50 40.50 43.50
8.50 9.00 11.00 12.50 15.00 20.00 25.38
5.62 6.62 8.00 9.12 11.50 15.75 20.00 23.62 28.00 32.75 35.50
5.50 6.50 7.56 8.19 10.62 13.38 16.00 17.12 20.88 24.19 25.00
4.75 5.75 6.88 7.25 9.31 12.12 14.62
4.00 4.75 5.50 6.00 7.50 10.00 12.69 14.88 17.00 19.50 20.81
4.25 5.00 5.88 6.38 7.88 10.50 13.25 15.56 17.75 20.25 21.62
4.75
6.00 7.50
1.12 1.50 1.69 2.06 3.19 4.31 5.31 9.25 10.75 12.62 15.50
2.00 2.50 2.88 3.12 4.25 6.00 7.56
2.50 3.00 3.50 3.75 4.50 5.50 6.75 8.00 9.50 10.50 11.75
3.06 3.25 3.75 4.13 5.00 6.25 7.50 8.75 10.25 11.50 12.75
1.88 3.25 4.00 4.50
4.00 3.25 4.00 4.00 5.00 6.00 8.00 8.62 13.75 14.88 15.69
4.25 3.50 4.31 4.38 5.31 6.50 8.50 9.31 14.50 15.62 16.50
3.25
4.25 5.00
4-28
4-28
8-24
0.4
15
0.4
15
0.6
35
0.7
50
0.8
70
1.1
140
1.7
285
25
184
143
140
83
29
48
.375
.25
.375
32
184
143
140
83
29
48
.375
.25
.375
40
184
216
229
216
143
140
120
83
102*
108*
29
52
64
78
48
102*
102*
.375
.25
.375
50
238
238
254
228
168
165
146
121
121
127
121
38
64
76
83
83
83
89
83
.375
.50
.375
65
279
279
295
279
203
192
175
140
140
149
43
73
89
95
102
102
110
.50
.50
.50
80
318
305
337
318
232
208
184
159
152
162
152
52
79
95
105
114
102
111
108
.50
.50
.50
100
381
397
381
292
270
236
191
200
191
81
108
114
127
127
135
127
.75
.75
.75
150
508
533
508
400
340
308
254
267
110
152
140
159
152
165
.75
.75
.75
10
7
15
16
18
23
4-28
20
32
4-28
28
64
8-24
0.4
15
10
7
Outlet
F
FF
8-24
43
129
8-24
2.3
500
2-20
4-16
36
76.00
76.00
66.00
61.50
24.56
25.60
25.60
2
2
2
3.4
4.0
4.5
5.1 5.63 6.75 7.5
8.5
1165 1600 2265 2982 3900 6200 7703 11720
4-16
30
63.00
64.50
56.00
54.60
21.31
22.50
24.00
2
2
2
2.8
780
4-16
24
61.50
63.24
53.16
43.93
30.75
31.62
17.75
19.25
19.25
22.06
22.90
1
1.5
1
4-16
20
52.00
53.62
45.00
41.90
15.00
16.50
16.50
1
1.5
1
8-24
8-24
18
46.00
47.64
41.50
39.06
12.95
15.00
15.00
1
1.5
1
4-16
Note: The top two flange holes on valve size 36 are threaded to 1 1/2"-6 UNC.
200
645
670
645
508
406
371
322
337
135
192
171
191
203
216
1
1
1
8-24
58
227
250
756
790
600
435
378
395
235
203
222
219
236
1
1
1
300
864
902
711
530
432
451
273
241
260
349
368
1
1.25
1
8-24
71
354
8-24
86
528
350
400
450
500
600
750
900
832
902 1054 1143 1350 1422 1676
614
635
992 1064 1116 1387 1562
495
528
781
514
549
803
321
394
329
381
451
541
624
267
298
381
419
489
572
650
292
324
381
419
489
610
650
378
399
560
397
419
582
1
1
1
1
1
2
2
1.5
2
1.5
1.5
1.5
2
2
1
1
1
1
1
2
2
8-24
102
726
114
130
143
171
190
216
1027 1353 1769 2812 3494 5316
2-20
4-16
4-16
4-16
4-16
4-16
Cla-Val Control Valves operate with maximum efficiency when mounted in horizontal piping with the main valve cover UP, however, other positions are acceptable. Due to
component size and weight of 8 inch and larger valves, installation with cover UP is advisable. We recommend isolation valves be installed on inlet and outlet for maintenance.
Adequate space above and around the valve for service personnel should be considered essential. A regular maintenance program should be established based on the specific
application data. However, we recommend a thorough inspection be done at least once a year. Consult factory for specific recommendations.
CLA-VAL
P.O. Box 1325 Newport Beach, CA 92659-0325 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: claval@cla-val.com Website cla-val.com
Copyright
E-100S/2100S (R-11/2012)
11
MODELS
Deluge Valve
U.L. Listed / U.L.C. Listed
Globe or Angle Pattern
Proven Reliable Design
DESIGN
ASSE
SSED
Type Approved
The Cla-Val Model 100G/2100G Deluge Valve is designed for use in controlling
water flow to Deluge, Pre-Action, or Foam-Water type fire protection sprinkler
systems. This valve is UL Listed in Special Systems Water Control Valves
Class I (VLFT) for both vertical and horizontal installation applications. The
Model 100G/2100G is a hydraulically-operated, diaphragm-actuated, globe or
angle pattern Deluge Valve. It consists of three major components: the body,
the cover, and the diaphragm assembly. The only moving part is the diaphragm
assembly. Packless construction and simplicity of design assures long service
life and dependable low maintenance for this valve. All ferrous parts are fusion
epoxy coated internally and externally for added corrosion resistance, along
with a Dura Kleen stem.
Typical Application
5
3
Specifications
3" 12"
Sizes Globe: 3" 12" Angle:
Ductile Iron 150 ANSI B16.42 flanged
End Details Cast Steel 150 ANSI B16.5 flanged
150 class, 250 psi maximum (Ductile Iron)
Pressure Rating 150 class, 285 psi maximum (All other materials)
300 class, 300 psi maximum (All materials)
Water, to 180F MAX.
Temperature Range Main Valve Body & Cover:
Materials Ductile Iron ASTM A-536* UL, ULC
Cast Steel ASTM A216-WCB* UL, ULC
Nickel Aluminum Bronze ASTM B148 UL, ULC
Naval Bronze ASTM B61 UL, ULC
316 Stainless Steel - ASTM A743 Grades
CF3M and CFM8
Super Austenitic Stainless Steel - ASTM A351
Grade CK3MCuN (SMO 254)
Super Duplex Stainless Steel - ASTMA890
Grade 5A (CE3MN)
Main Valve Internal Trim:
Bronze ASTM B61 Monel QQ-N-281 Class B
Diaphragm and Disc:
Buna-N synthetic rubber
*Internally & Externally Epoxy Coated
12
Specifications
Sizes
To calculate the maximum wet sprinkler pilot height above the valve, use the graph below.
Functional Data
Valve Size
CV
Factor
INLET
Inches
10
12
mm
80
100
150
200
250
300
1245 1725
115
200
440
770
27.6
48
105.6
184.8
139
240
541
990
1575 2500*
33.4
58
130
238
378
299
414
600
OUTLET
OUTLET
INLET
Valve Size (In.)
10
12
80
100
150
200
250
A 150 ANSI
12.00
15.00
20.00
25.38
29.75
A 150 ANSI
305
381
508
645
756
AA 300 ANSI
13.25
15.62
21.00
26.38
31.12
34.00
AA 300 ANSI
337
397
533
670
791
864
B Dia.
9.12
11.50
15.75
20.00
23.62
35.50
B Dia.
232
292
400
508
600
902
C Max.
8.19
10.62
13.38
16.00
17.12
C Max.
208
270
340
406
435
2.56
3.19
4.31
5.16
8.50
28.00
65
81
110
131
216
711
E 150 ANSI
7.00
8.50
10.00
12.69
14.88
20.88
E 150 ANSI
178
216
254
322
378
530
--
8.81
10.50
13.19
--
EE 300 ANSI
--
224
267
350
--
4.00
4.97
6.00
8.00
8.62
F 150 ANSI
102
126
152
203
219
--
5.28
6.50
8.50
--
17.00
FF 300 ANSI
--
134
165
216
--
432
4.75
5.94
7.25
8.50
10.50
17.75
121
151
184
216
267
451
2.69
2.81
3.88
5.31
6.56
68
71
99
135
167
2.56
2.81
3.81
4.81
5.81
10.75
65
71
97
122
148
273
7.00
4.03
6.75
17.00
15.50
178
102
171
432
394
2.56
2.81
3.81
4.81
8.50
9.50
65
71
97
122
216
241
4.00
4.24
10.25
102
108
260
EE 300 ANSI
F 150 ANSI
FF 300 ANSI
1.75
2.41
2.75
N NPT
1/2 - 14
3/4 -14
3/4 - 14
P NPT
1-1/4 -11-1/2
1 - 11-1/2 1 -11-1/2
2 - 11-1/2
R 150 ANSI
2.50
3.47
3.25
4.19
7.12
14.50
RR 300 ANSI
3.12
3.78
3.75
4.69
7.81
X Pilot System
15.00
17.00
29.00
31.00
Y Pilot System
11.00
12.00
20.00
Z Pilot System
11.00
12.00
20.00
45
61
70
N NPT
1/2 - 14
3/4 - 14
3/4 -14
P NPT
1-1/4 -11-1/2
2 -11-1/2
64
88
83
106
181
368
RR 300 ANSI
79
96
95
119
198
33.00
X Pilot System
381
432
737
787
838
22.00
24.00
1.25
Y Pilot System
279
305
508
559
610
1.25
22.00
24.00
Z Pilot System
279
305
508
559
610
CLA-VAL
R 150 ANSI
1 - 11 1/2 1 - 11-1/2
300
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
13
Ti 100GS
MODEL
Seawater Version
DESIGN
ASSE
SSED
Type Approved
The Cla-Val Model Ti 100GS Deluge Valve is designed for use in controlling water
flow to Deluge, Pre-Action, or Foam-Water type fire protection sprinkler systems.
This valve is U.L. Listed in "Special Systems Water Control Valves Class I
(VLFT)". The Model Ti 100GS is a hydraulically-operated, diaphragm-actuated,
globe or angle pattern Deluge Valve. It consists of three major components: the
body, the cover, and the diaphragm assembly. The only moving part is the
diaphragm assembly. Packless construction and simplicity of design assures long
service life and dependable low maintenance for this valve.
The Ti 100GS are manufactured in materials suitable for seawater.
Typical Application
The Model Ti 100GS is installed to control the water flow to the sprinklers in Deluge, Pre-Action, or Foam-Water type systems. A sim4
plified system is used to illustrate typical operation.
The Model Ti 100GS Deluge Valve (3) is maintained in the closed position by means of system water pressure controlled by a pilot control (4). When the pilot control valve receives
a signal from the fire detection system, it
allows the deluge valve to open. Firefighting
water (1) then enters system piping (5)
and discharges from sprinklers (6).
Sizes:
End Details:
Pressure Rating:
26 bar max.
Temperature
Range:
Material:
14
5
2
Specifications
FrictionLoss
Ti 100GS (Globe):
3" Size=42 Ft. of 3" Pipe
4" Size=92 Ft. of 4" Pipe
6" Size=116 Ft. of 6" Pipe
2. Size
4. Internal Trim Material
Globe:
To calculate the maximum wet sprinkler pilot height above the valve, use the graph below.
Functional Data
Inches
Valve Size
mm
3
80
115
27.6
4
100
200
48
6
150
440
105.6
80
100
150
20.00
A 150 ANSI
305
381
508
11.50
15.75
B Dia.
232
292
400
8.19
10.62
13.38
C Max.
208
270
340
2.56
3.19
4.31
65
81
110
7.00
4.03
6.75
178
102
171
2.56
2.81
3.81
65
71
97
N NPT
1/2"-14
3/4"-14
3/4"-14
N NPT
1/2"-14
3/4"-14
3/4"-14
P NPT
1 1/4"-11 1/2
2"-11 1/2"
2"-11 1/2"
P NPT
1 1/4"-11 1/2
2"-11 1/2"
2"-11 1/2"
R 150 ANSI
2.50
3.47
3.25
R 150 ANSI
64
88
83
X Pilot System
15.00
17.00
29.00
X Pilot System
381
432
737
Y Pilot System
11.00
12.00
20.00
Y Pilot System
279
305
508
Z Pilot System
11.00
12.00
20.00
Z Pilot System
279
305
508
A 150 ANSI
12.00
15.00
B Dia.
9.12
C Max.
CLA-VAL
E-100GS Ti (R-05/2014)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
15
CLA-VAL
solenoid
TITANIUM
Available in sizes
3 through 6
Consult factory for
other sizes
UL
Got Vibration?
Cla-Val valves with anti-cavitation trim are the ideal solution for applications
with a high probability of vibration
Cla-Vals patented KOanti-cavitation trim helps protect piping from damage caused by vibration
Minimizes vibration across the relief valve during pump starts
Alleviates vibration caused by cavitation when discharging to atmosphere or in other applications
with excessive pressure fluctuations
Special alloys and metals available, including Monel, and 316Stainless Steel
Existing Cla-Val control valves can field retrofitted with KOanti-cavitation trim
Proven track record of trouble-free performance on offshore platforms around the world
Backed by more than seventy years of industry experience
Three-year warranty
100-01KO
MODEL
Principle of Operation
On-Off Control
18
On-Off Control
Modulating
Control
Modulating Action
The valve holds any intermediate position when operating pressures are
equal above and below the
diaphragm. A Cla-Val Modulating
Pilot Control will allow the valve to
automatically compensate
for line pressure changes.
Specifications
Pattern
Size
Globe
1" - 36"
Pressure Ratings
Angle
1" - 16" & 24"
ANSI
Standards*
ASTM A536
Ductile Iron B16.42
ASTM A216-WCB Cast Steel B16.5
ASTM B62
Bronze
B16.24
Material
Grooved Threaded
150
300
Class Class
250 400
285
400
225
400
300
Class
400
400
400
End
Details
400
400
400
Note:
Component
Body & Cover
Available Sizes
Disc Retainer &
Diaphragm Washer
Trim: Disc Guide,
Seat & Cover Bearing
Disc
Diaphragm
Stem, Nut & Spring
100-01
1" 16"
Cast Iron
Cast Steel
Bronze
B (Diameter)
Inlet
Outlet
G
GG
GGG
F
FF
Note:
Consult Factory
on 10",12", 16"
angle pattern
CC
(MAX)
Inlet
Outlet
EE
GGGG
D
DD
DDD
Grooved
Inlet
1" - 16"
100-01KO
(MAX)
A
AA
AAA
1" - 36"
B (Diameter)
Threaded &
Flanged
Model 100-01KO
APPROVED
(4" - 24")
Materials
Pressure Class
Grooved End
1 1/2" - 8"
Inlet
DDDD
AAAA
1
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
0.4
15
25
184
143
140
83
29
48
.375
.25
.375
10
7
1 1/4
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
0.4
15
32
184
143
140
120
83
29
48
.375
.25
.375
10
7
1 1/2
7.25
8.50
9.00
8.50
5.62
5.50
4.75
3.25
4.00
4.25
1.12
2.00
2.50
3.06
1.88
4.00
4.25
.375
.25
.375
0.4
15
40
184
216
229
216
143
140
120
83
102
108
29
52
64
78
48
102*
102*
.375
.25
.375
10
7
2
9.38
9.38
10.00
9.00
6.62
6.50
5.75
4.75
4.75
5.00
4.75
1.50
2.50
3.00
3.25
3.25
3.25
3.50
3.25
.375
.50
.375
0.6
35
50
238
238
254
228
168
165
146
121
121
127
121
38
64
76
83
83
83
89
83
.375
.50
.375
15
16
2 1/2
11.00
11.00
11.62
11.00
8.00
7.56
6.88
5.50
5.50
5.88
1.69
2.88
3.50
3.75
4.00
4.00
4.31
.50
.50
.50
0.7
50
65
279
279
295
279
203
192
175
140
140
149
43
73
89
95
102
102
110
.50
.50
.50
18
23
3
12.50
12.00
13.25
12.50
9.12
8.19
7.25
6.25
6.00
6.38
6.00
2.06
3.12
3.75
4.13
4.50
4.00
4.38
4.25
.50
.50
.50
0.8
70
80
318
305
337
318
232
208
184
159
152
162
152
52
79
95
105
114
102
111
108
.50
.50
.50
20
32
15.00
15.62
15.00
11.50
10.62
9.31
7.50
7.88
7.50
3.19
4.25
4.50
5.00
5.00
5.31
5.00
.75
.75
.75
1.1
140
100
381
397
381
292
270
236
191
200
191
81
108
114
127
127
135
127
.75
.75
.75
28
64
20.00
21.00
20.00
15.75
13.38
12.12
10.00
10.50
4.31
6.00
5.50
6.25
6.00
6.50
.75
.75
.75
1.7
285
150
508
533
508
400
340
308
254
267
110
152
140
159
152
165
.75
.75
.75
43
129
25.38
26.38
25.38
20.00
16.00
14.62
12.69
13.25
5.31
7.56
6.75
7.50
8.00
8.50
1
1
1
2.3
500
200
645
670
645
508
406
371
322
337
135
192
171
191
203
216
1
1
1
58
227
10
29.75
31.12
23.62
17.12
14.88
15.56
9.25
8.00
8.75
8.62
9.31
1
1
1
2.8
780
250
756
790
600
435
378
395
235
203
222
219
236
1
1
1
71
354
12
34.00
35.50
28.00
20.88
17.00
17.75
10.75
9.50
10.25
13.75
14.50
1
1.25
1
3.4
1165
300
864
902
711
530
432
451
273
241
260
349
368
1
1.25
1
86
528
14
39.00
40.50
32.75
24.19
19.50
20.25
12.62
10.50
11.50
14.88
15.62
1
1.5
1
4.0
1600
350
991
1029
832
614
495
514
321
267
292
378
397
1
1.5
1
102
726
16
41.38
43.50
35.50
25.00
20.81
21.62
15.50
11.75
12.75
15.69
16.50
1
2
1
4.5
2265
400
1051
1105
902
635
528
549
394
298
324
399
419
1
2
1
114
1027
18
46.00
47.64
41.50
39.06
12.95
15.00
15.00
1
1
1
5.1
2982
450
1168
1210
1054
992
329
381
381
1
1
1
130
1353
20
52.00
53.62
45.00
41.90
15.00
16.50
16.50
1
1
1
5.63
3900
500
1321
1362
1143
1064
381
419
419
1
1
1
143
1769
24
61.50
63.24
53.16
43.93
30.75
31.62
17.75
19.25
19.25
1
1
1
6.75
6200
600
1562
1606
1350
1116
781
803
451
489
489
1
1
1
171
2812
30
63.00
64.50
56.00
54.60
21.31
22.50
24.00
2
2
2
7.5
7703
750
1600
1638
1422
1387
541
572
610
2
2
2
190
3494
36
76.00
76.00
66.00
61.50
24.56
25.60
25.60
2
2
2
8.5
11720
900
1930
1930
1676
1562
624
650
650
2
2
2
216
5316
Cla-Val Control Valves with KO ANTI-CAVITATION Trim operate with maximum efficiency when mounted in horizontal piping with the main valve cover Up. We recommend isolation valves
be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be considered essential. A regular maintenance program should
be established based on the specific application data. However, we recommend a thorough inspection be done at least once a year. Consult factory for specific recommendations.
19
Functional Data
Model 100-01KO
Inches
Valve Size
114
112
212
10
12
14
16
18
20
24
30
36
25
32
40
50
65
80 100 150 200 250 300 350 400 450 500 600 750 900
14
14
14
25
37
52
90 218 362 660 810 1100 1200 1550 1950 3900 6100 9150
Gal./Min.
(gpm.)
Globe
CV
3.4 3.4 3.4 6.0 8.9 12.5 21.6 52
87 159 194 264 288 360 469 938 1466 2199
Pattern Litres/Sec. (l/s.)
Factor
15
15
15
26
39
55
95
232
388
479 790 1075 1175
3775
Gal./Min.
(gpm.)
Angle
3.6 3.6 3.6 6.2 9.4 13.2 22.8 56
93
115 190 258 282
906
Feet
(ft.)
Pipe
Angle
52
52
52
67
76
113 157 231 349 650 678 616 961
787
Angle Pattern
Liquid Displaced from
0.2 0.2 0.2 .03 .04 .08 .17 .53 1.26 2.5 4.0 6.5 9.6
11
12
29
65
90
U.S. Gal.
Cover Chamber When
Valve Opens
0.8 0.8 0.8 .12 .16 .30 .64 2.0 4.8 9.5 15.1 25.6 36.2 41.6 45.4 110 246 340
Litres
For assistance in selecting appropriate valve options or valves manufactured with special design requirements, please contact our Regional Sales Office or Factory.
C V Factor
Where:
mm.
CV =
Q = CV
Q
P= C
V
K = 894d
Cv 2
P):
or
= Kd
Fluid Velocity
Fluid velocity can be calculated from the following formula:
(U.S. system units)
.4085 Q
d2
K
L
Q
V
P
12 f
V=
PIPE PLUG
SOLID LINE IS FULL OPEN FLOW CURVES FOR 18 FT/SEC CONTINUOUS DUTY APPLICATIONS
DASHED LINE IS FULL OPEN FLOW CURVE FOR 25 FT/SEC INTERMITTENT DUTY APPLICATIONS
HEX NUT
COVER
400
300
PIPE PLUG
Cover Bolt
COVER BEARING
100
SPRING
1 1/2"
1 1/4"
10
4"
12" 18"
8"
10" 14"16"
6"
20"
24"
30"
STEM NUT
36"
DIAPHRAGM WASHER
24"
*DIAPHRAGM
1"
DISC RETAINER
*SPACER WASHERS
1
10
100
10000
1000
FLOW RATE (gpm)
KO
DISC GUIDE
Notes: On Operating Differential
1. For atmospheric discharge, the
maximum inlet pressure cannot
exceed 150 psi.
KO
2. For pressure differentials greater
SEAT
than 300 psi the maximum flow
velocity should not exceed 18 ft/sec.
3. Flow velocities greater than 25 ft/sec
are not recommended.
4. Recommended minimum flow velocity
BODY
is 1 ft/sec.
(Globe
5. Consult factory for conditions
Shown)
exceeding these recommendations.
400
350
Cavitation
Zone
300
250
200
150
100
50
0
0
10
20
30
40
50
60
70
20
80
90
100000
*DISC
100
STEM
Seat Screw
8" and Larger
SEAT ORING
STUD
8" and Larger
PIPE PLUG
*Repair Parts
The valve shall be hydraulically operated, single diaphragm actuated, globe pattern. The valve shall consist of three major components: the body with seat installed, the cover with bearing installed, and the diaphragm assembly. The diaphragm assembly shall be
the only moving part and shall form a sealed chamber in the upper portion of the valve, separating operating pressure from line pressure. Packing glands and/or stuffing boxes are not permitted and there shall be no pistons operating the main valve or pilot controls.
Ductile Iron is standard, other materials shall be available. No fabrication or welding shall be used in the manufacturing process.
Description
The anti-cavitation features of the seat and disc guide detail shall have flow slots equally spaced around their perimeters. The seat slots shall be
orientated around the perimeter of the seat so that fluid entering the valve shall flow through the seat slot detail such that the fluid flow converges
in the center chamber of the seat allowing potential cavitation to dissipate. The disc guide slots shall be positioned around the perimeter of the
disc guide, configured and oriented in an angular direction so that fluid flow exiting through the slots is diverted away from direct impact into pressure boundary surfaces. Flow exiting the disc guide slots is directed in an angular path to increase the distance between the slot geometry and
pressure boundary surfaces. If cavitation conditions exist, the increased distance between the slots and pressure boundary surfaces minimizes
the potential for damage by allowing the cavitation bubbles to dissipate before they come in contact with pressure boundary surfaces. Anti-cavitation characteristics shall be controlled by the described slotted seat and disc guide components. The disc guide shall slide in the seat and allow
controlled flow through the seat slots into the central seat chamber where flow shall continue from the seat chamber and exit through the angularly
oriented slots of the disc guide. The seat and disc guide features used together shall provide anti-cavitation characteristics suitable for applications where a large controlled pressure drop is desired.
The flexible, non-wicking, FDA approved diaphragm shall consist of nylon fabric bonded with synthetic rubber compatible with the
operating fluid. The diaphragm must withstand a Mullins burst test of a minimum of 600 psi per layer of nylon fabric and shall be cycle
tested 100,000 times to insure longevity. The diaphragm shall be fully supported in the valve body and cover by machined surfaces
which support no less than one-half of the total surface area of the diaphragm in either the fully open or fully closed position.
The valve seat in six inch and smaller size valves shall be threaded into the body. Valve seat in eight inch and larger size valves
shall be retained by flat head machine screws for ease of maintenance. The seat shall be of the solid, one-piece design and shall
have a minimum of a five degree taper on the seating surface for positive drip-tight shut-off. Pressed-in bearings and/or multi-piece
seats shall not be permitted.
To insure proper alignment of the valve stem, the valve body and cover shall be machined with a locating lip. No "pinned" covers to
the valve body shall be permitted. All necessary repairs and/or modifications other than replacement of the main valve body shall be
possible without removing the valve from the pipeline.
The valve manufacturer shall warrant the valve to be free of defects in material and workmanship for a period of three years from
date of shipment, provided the valve is installed and used in accordance with all applicable instructions. The valve manufacturer shall
be able to supply a complete line of equipment from 114" through 48" sizes and a complete selection of complementary equipment.
Material Specification
Valve Size:
Main Valve Body and Cover:
Main Valve Trim:
End Detail:
Pressure Rating:
Temperature Range:
Coating:
Desired Options:
Application Information
Inlet/Outlet Pressures:
Flow Rate:
Pipe Diameter:
Function (i.e. - Pressure Reducing, Pressure Relief, etc.):
Patented
This valve shall be a Cla-Val Model No. 100-01KO Hytrol Main Valve with
Anti-Cavitation Trim as manufactured by Cla-Val, Newport Beach, CA
Note: Add this Hytrol Anti-Cavitation Trim Purchase Specification to main valve
specification for control valves where there is a high potential for cavitation damage.
Please contact our Regional Sales Offices or Factory for assistance.
CLA-VAL
COPYRIGHT
CLA-VAL EUROPE
Chemin ds Mesanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax:
41-21-643-15-50
www.cla-val.com
21
100-42
MODEL
700 Series
Roll Seal
The Cla-Val Model 100-42 Roll Seal valve is a hydraulically operated valve used
to control liquid flow by means of a flexible control element: the liner.
The basic valve consists of only two parts: a one piece, investment cast body
and an elastomeric liner. The valve body is constructed with internal ribs and
slots forming a grillwork which surrounds the liner to provide support. A normally
closed type valve is formed by the installed liner which covers the grillwork and
seats against the raised seating surface in the valve body.
Upstream pressure actuates the valve to produce valve opening by rolling the
liner off the seating surface and the slotted grillwork.
The valve is actuated by upstream pressure as the loading pressure (pressure
supplied to the control chamber) is varied by an external pilot control system.
A typical pilot control system used to operate the Model 100-42 valve consists
of a restriction and a suitable pilot connected to the valve.
Principle of Operation
Pilot
Control
Valve
PILOT
CONTROL
VALVE
Pilot
Control
Valve
RESTRICTOR
RESTRICTOR
RESTRICTOR
SEATING AREA
SEATING AREA
INLET
CONTROL CHAMBER
SEATING AREA
INLET
CONTROL CHAMBER
INLET
CONTROL CHAMBER
Design Specification
Sizes:
Operating Pressure:
Maximum Differential:
Reverse Pressure:
Temperature Range:
Flange Operating Pressure:
Performance Specification
Capacity:
Cf Factor:
Cavitation:
Rangeability:
Bearing Friction:
Material Specification
Body:
316L Stainless Steel
Flanges: (Slip on) Carbon Steel/Clear Cad. Plated
Bolt Kit:
Carbon Steel/Zinc Plated
Liner:
Natural Rubber, 65 duro (standard)
Viton, EPDM, Nitrile, Silicone (available)
Liner Retainer:
316 Stainless Steel
Optional Materials
Escoloy 45D
Duplex Stainless Steel
Super Duplex Stainless Steel
Nickel Aluminum Bronze
Titanium
2
278
-438
-212
---4
4
224
3
3916
-578
-314
---712
712
469
50
73
-111
-64
---1.81
2.72
1.81
5
14
4
418
-738
-4
---14
14
794
80
90
-149
-83
---3.63
4.54
3.63
6.35
30
100
105
-187
-102
---6.35
10
6.35
11.8
50
6
514
1078
91316
9
512
11
1212
3
8
58
87
1787
8
-1438
-11
-1312
15
3
8
115
155
3177
10
-18
-13
-16
1712
1
2
190
250
4964
12
-2158
-1514
-19
2012
1
2
290
375
7148
150
200
250
300
133
---276
356
457
549
249
---229
279
330
387
140
---279
343
406
483
318
381
445
521
3
3
1
1
8
8
2
2
30
54.43
89
151.5
----41.73 72.57 116.57 191
----113
200
301
451
3/8" N.P.T.
3 PORTS
"A" TYP.
"BB"
DIA.
FLOW
"CC"
2", 3", 4" and 6" Wafer Style
"E" N.P.T.
"D"
DIA.
"E" N.P.T.
"E" N.P.T.
"B"
DIA.
"C"
2.
6.
Valve Size
7.
3.
8.
CLA-VAL
5.
Represented By:
COPYRIGHT
CLA-VAL EUROPE
Chemin ds Mesanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax:
41-21-643-15-50
www.cla-val.com
23
100-29S
MODEL
600 Series
Principle of Operation
24
On-Off Control
Modulating
Control
On-Off Control
Modulating Action
The valve holds any intermediate
position when operating pressure is
equal above and below the
diaphragm. Using a Cla-Val
Modulating Control will
allow the valve to automatically compensate for line
pressure changes.
Functional Data
Valve Size
CV
Factor
Equivalent
Length
of
Pipe
Model 100-29S
Inches
10
12
14
16
18
20
24
30
36
42
48
mm.
80
100
150
200
250
300
350
400
460
500
600
750
900
1000
1200
62
136
229
480
930
1458 1725
15
32.5
55
115
223
350
414
506
705
816
966
1895
2858
3483
3796
135
233
545
CF**
CF**
CF**
CF**
CF**
CF**
CF**
32
56
132
CF**
CF**
CF**
CF**
CF**
CF**
CF**
Feet (ft.)
293
251
777
748
621
654
750
977
983
1125
3005
2130
2862
4232
7028
89.3
254
751
77.6
229
Globe Pattern
20.6
12.7
Angle Pattern
12.9
Globe
Pattern Meters (m.)
Angle Feet (ft.)
Pattern Meters (m.)
K
Factor
Fl. Oz
Liquid Displaced from U.S. Gal.
Cover Chamber
When Valve Opens ml
Litres
229
298
300
343
917
650
872
1290
2142
580
CF**
CF**
CF**
CF**
CF**
CF**
CF**
176.9
CF**
CF**
CF**
CF**
CF**
CF**
CF**
23.1
15.7
10.4
8.5
8.9
10.2
8.4
8.8
19.1
10.5
9.7
12.3
17.8
22.3
12.2
CF**
CF**
CF**
CF**
CF**
CF**
CF**
0.32
.08
.17
.53
1.26
2.51
4.0
4.0
9.6
9.6
9.6
29.0
42
90
90
.12
.30
.64
2.0
4.8
9.5
15.1
15.1
36.2
36.2
36.2
110
197
340
**Consult Factory
C V Factor
Where:
CV =
340
*Estimated
Q
P
Q = CV
Q
P= C
V
K = 894d
Cv 2
or
P):
= Kd
12 f
.4085 Q
V=
d2
K
L
Q
V
P
Model 100-29S Flow Chart (Based on normal flow through a wide open valve)
25
Specifications
Model 100-29S
Available Sizes
Pattern
Globe
Fluids
3",4",6",8",10",12",16",18,20",24",30,36, 42, 48
4",6",8"
Angle
Pressure Ratings
-40 to 180 F
Material
Specifications
Pressure Class
Flanged
ANSI
150
300
Standards**
Class
Class
Threaded
End
Details
Ductile Iron*
ASTM-A536
B16.42
250
640
400
Cast Steel*
ASTM A216
B16.5
285
740
400
Naval Bronze
ASTM B61
B16.24
225
500
400
B16.5
285
720
400
B.16.24
225
500
400
B16.5
285
720
400
Stainless Steel
ASTM A743-CF-8M
Type 316
NI.AL.Bronze
ASTM B148
Super Duplex
Stainless Steel
Note:
Materials
Component
Ductile Iron
Available Sizes
114" - 48"
Cast Steel
114" - 16"
Bronze
114" -16"
Stainless Steel
NI. AL. Bronze
Type 316
114" -16"
114" -16"
Options
Epoxy Coating - suffix KC
An FDA approved fusion bonded epoxy
coating for use with cast iron, ductile iron
or steel valves. This coating is resistant to
various water conditions, certain acids,
chemicals, solvents and alkalies. Epoxy
coatings are applied in accordance with
AWWA coating specifications C116-03. Do
not use with temperatures above 175 F.
Water Treatment Clearance - suffix KW
This additional clearance is beneficial in
applications where water treatment compounds can interfere with the closing of the
valve. The smaller outside diameter disc
guide provides more clearance between
the disc guide and the valve seat. This
option is best suited for valves used in onoff (non-modulating) service.
26
Super Duplex
Stainless Steel
114" -16"
Super Duplex
Stainless Steel
B (Diameter)
100-29S
100-20
Threaded
&Flanged
Flanged
B (DIAMETER)
J
Dimensions
C
(MAX)
Outlet
Inlet
F
FF
Inlet
A
AA
OUTLET
INLET
E
EE
F FF
H
D
DD
100-29S
A
AA
3
4
10.25 13.88
11.00 14.50
6.62 9.12
7.00 8.62
6.94
7.25
5.50
5.81
3.75 4.50
4.12 5.00
.375
.50
.50
.50
.375
.50
10-32 14-28
0.6
0.8
45
85
6
17.75
18.62
11.50
11.62
8.88
9.38
6.75
7.25
5.50
6.25
.75
.75
.75
1
4-28
1.1
195
8
21.38
22.38
15.75
15.00
10.69
11.19
7.25
7.75
6.75
7.50
.75
.75
.75
3
8-24
1.7
330
10
26.00
27.38
20.00
17.88
12
30.00
31.50
23.62
21.00
14
34.25
35.75
27.47
20.88
16
35.00
36.62
28.00
25.75
18
42.12
43.63
35.44
25.00
20
48.00
49.62
35.44
31.50
24
48.00
49.75
35.44
31.50
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
8.00
8.75
1
1
1
3
8-24
2.3
625
9.50
10.25
1
1
1
3
8-24
2.8
900
11.00
1
1.25
1
3
8-24
3.4
1250
11.75
12.75
1
1.25
1
3
8-24
3.4
1380
15.88
15.88
1
2
1
1
2-20
4.5
1500
14.56
16.06
1
2
1
1
2-20
4.5
2551
17.00
19.00
1
2
1
1
2-20
4.5
2733
150
451
473
292
295
226
238
171
184
140
159
.75
.75
.75
1
4-28
28
89
200
543
568
400
381
272
284
184
197
171
191
.75
.75
.75
3
8-24
43
150
250
660
695
508
454
300
762
800
600
533
350
870
908
698
530
400
889
930
711
654
450
1070
1108
900
635
500
1219
1260
900
800
600
1219
1263
900
800
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
CF*
203
222
1
1
1
3
8-24
58
284
241
260
1
1
1
3
8-24
71
409
279
1
1.25
1
3
8-24
86
568
298
324
1
1.25
1
3
8-24
86
627
403
403
1
2
1
1
2-20
86
681
370
408
1
2
1
1
2-20
114
1157
432
483
1
2
1
1
2-20
114
1249
30
63.25
63.75
53.19
43.94
19.88
22.00
1
2
1
3
4-16
6.5
6500
36
42
65.00 76.00
67.00 76.00
56.00 66.00
54.60 61.50
25.50 28.00
27.50 28.00
2
2
2
2
2
2
3
4-16 M20
7.5
8.5
8545 12450
48
94.50
94.50
66.00
61.50
31.50
31.50
2
2
2
M20
8.5
13100
Note: The top two flange holes on valve sizes 36 thru 48 are threaded to 1 1/2"-6 UNC.
*Consult Factory
DD 300 ANSI
E 150 ANSI
EE 300 ANSI
F 150 ANSI
95
FF 300 ANSI
105
H NPT Body Tapping
.375
J NPT Cover Center Plug
.50
K NPT Cover Tapping
.375
Valve Stem Internal Thread UNF 10-32
Stem Travel
15
Approx. Ship Wt. Kgs.
20
100
353
368
232
219
176
184
140
148
114
127
.50
.50
.50
1
4-28
20
39
750
1607
1619
1351
1116
505
559
1
2
1
3
4-16
165
2951
900
1651
1702
1422
1387
648
699
2
2
2
3
4-16
191
3876
1000
1930
1930
1676
1562
711
711
2
2
2
M20
216
5647
1200
2400
2400
1676
1562
800
800
2
2
2
M20
216
5942
For assistance in selecting appropriate valve options or valves manufactured with special design requirements, please contact our Regional Sales Office or Factory.
CLA-VAL
COPYRIGHT
Represented By:
CLA-VAL EUROPE
Chemin ds Mesanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax:
41-21-643-15-50
www.cla-val.com
27
800GS
MODEL
Deluge Valve
Low Head Loss
Cast Steel Construction
Stainless Steel Pilot and Tubing
Stainless Steel Solenoid
Anti-Cavitation Design
Fusion Coated Epoxy Inside and Out
Nickel Aluminum Bronze Construction Option (ASTM B148)
Super Duplex Stainless Steel Construction Option (ASTM A890
GR5A)
Low Maintenance
Simple and Reliable Operation
1-Year Warranty
Principle of Operation
Control Options
Electric Operation
Pneumatic Operation
Hydraulic Operation
Manual Operation
Outlet
Inlet
FLOW
28
Outlet
Inlet
FLOW
Dimensions
Model 800GS
Valve Size (Inches)
L
D
T-1/T-2 (NPT)
T-3 (NPT)
Approx. Wt. (Lbs.)
"L"
T-2
T-1
T-1
"D"
6
10
4
8
17.25 18.25 20.00 22.00
9.5 11.75 14.00 16.00
1/2
1/2
1/2
1/2
2
2
2
2
151
196
330
285
100
438
241
1/2
2
68
150
464
299
1/2
2
89
200
508
356
1/2
2
129
250
559
406
1/2
2
150
FLOW FACTORS
T-3
T-2
KV
77.3
201
379
550
*Calculated
MAIN VALVE
Ends:
Body:
Tube Diaphragm:
Barrier:
Bolts:
Pressure:
Temp. Range:
MAIN VALVE OPTIONS
Body:
FLOW
PILOT VALVE
All Parts:
O-Rings:
Control Range:
Pilot Pressure Range:
Operation:
PILOT VALVE OPTIONS
All Parts:
Operation:
2. Valve Size
Cla-Val 800 Series Control Valves operate with maximum efficiency when mounted in horizontal or vertical piping. We recommend isolation valves
be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be considered essential.
A regular maintenance program should be established based on the specific application data. However, we recommend a thorough inspection be
done at least once a year. Consult factory for specific recommendations.
CLA-VAL
E-800GS (R-03/2015)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
29
100-43
MODEL
800 Series
The Cla-Val Model 100-43 Tubular Diaphragm Valve is a pressure-operated, in-line axial valve. A tube diaphragm actuates the valve, which is comprised of three major components: 1) Tube 2) Barrier and 3) Body. There is
only one moving part in the valve the tube diaphragm. There are no
shafts, packing, stem guides or springs.
The tube diaphragm is a one piece, homogeneous nitrile rubber part which
is extremely durable. The ends of the tube are thick solid rubber, designed
to fit between mating flanges. This design eliminates the possibility of cutting
the tube diaphragm due to over tightening or piping misalignment during
installation.
The tube forms a drip tight seal around the barrier when the pressure is
equalized between the valve inlet and the control chamber. When pressure
is removed from the control chamber, the valve is open. The minimum recommended operating pressure is 40 P.S.I. of inlet pressure.
Principle of Operation
Outlet
Inlet
Inlet
Inlet
Outlet
FLOW
Outlet
FLOW
FLOW
Modulating Action
The valve tube diaphragm holds any intermediate position when a quantity of water
is exhausted from the control chamber via
the pilot. The quantity of water in the control chamber is established by the set
pressure of the pilot.
The control chamber is filled or exhausted
to atmosphere, maintaining set
pressure.
30
Model 100-43
MAIN VALVE
Ends:
Body:
Tube Diaphragm:
Barrier:
Bolts:
Pressure:
Temp. Range:
Dimensions
"L"
T-2
T-1
T-1
"D"
10
8.75
9.75
10.75
11.75
14.00
7.5
9.5
11.75
14.00
16.44
T-1 (NPT)
1/4
1/4
1/4
3/8
1/2
T-2 (NPT)
1/4
1/2
1/2
1/2
1/2
67
99
135
185
270
80
100
150
200
200
222
248
273
299
299
191
241
299
356
356
T-1 (NPT)
1/4
1/4
1/4
3/8
1/2
T-2 (NPT)
1/4
1/2
1/2
1/2
1/2
30
45
61
84
123
T-1
T-1
FLOW FACTORS
SIZE (IN) CV (gpm)
160
3
340
4
885
6
1667
8
2424
*10
T-2
FLOW
KV
36.4
77.3
201
379
550
* Calculated
2. Valve Size
CLA-VAL
1701 Placentia Avenue Costa Mesa CA 92627
800-942-6326 Fax: 949-548-5441 Web Site: cla-val.com E-mail: info@cla-val.com
CLA-VAL CANADA
4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone: 905-563-4963
Fax:
905-563-4040
E-mail sales@cla-val.ca
E-100-43 (R-09/2016)
COPYRIGHT
CLA-VAL EUROPE
Chemin des Msanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax:
41-21-643-15-50
E-mail: cla-val@cla-val.ch
CLA-VAL UK
Dainton House, Goods Station Road
Tunbridge Wells
Kent TN1 2 DH England
Phone: 44-1892-514-400
Fax:
44-1892-543-423
E-mail: info@cla-val.co.uk
CLA-VAL FRANCE
Porte du Grand Lyon 1
ZAC du Champ du Prier
France - 01700 Neyron
Phone: 33-4-72-25-92-93
Fax: 33-4-72-25-04-17
E-mail: cla-val@cla-val.fr
CLA-VAL PACIFIC
45 Kennaway Road
Woolston, Christchurch, 8023
New Zealand
Phone: 64-39644860
www.cla-valpacific.com
E-mail: info@cla-valpacific.com
31
X43H
MODEL
Now available up to
48-inches/1200 mm
10 12 141620
24
Constant Downstream
Pressure
/2
10
1
100
CV (Gal/Min. - gpm.)
CV (Litres/Sec - l/s.)
1,000
Flow (gpm)
10,000
100,000 200,000
CV Factor
Strainer Size (inches)
18
11
2 1/
1 12
96
23
2
150
36
2 12
254
61
3
367
85
4
654
157
6
1644
395
8
3922
702
Cv in gpm = gpm @ 1psid head loss Cv in l/s = l/s @ 1bar head loss
32
10
4566
1097
12
6800
1580
14
16
18
20
24
8949 11692 12796 18264 26302
2150 2809 3555 4388 6319
Specifications
Sizes (Inches):
Sizes (mm):
Ends:
Max Pressure Rating:
Fluids:
Temperature:
Materials:
Body & Cover:
Cover Seal:
Strainer:
Strainer Mesh Sizes:
Drain/Blow-Off Connection:
Bolts:
112, 2, 212, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24, 36 and 48
40, 50, 65, 80,100, 150, 200, 250, 300, 350, 400, 450, 500, 600, 900 and 1200
Flanged, ANSI Class 150 and 300 (Note: 300# Flanges are Raised Face)
150 - 250 psi 300 - 400 psi
Compatible with Materials of Construction
Maximum 180F
Ductile Iron ANSI B16.62; Fusion Bonded Epoxy Coating Standard or
NiAIBrz ASTM B148
Buna-N Synthetic Rubber
316 Stainless Steel; Ductile Iron, Epoxy Coated Frame or in
Titanium on a NiAIBrz Frame
Standard 10 mesh / 2000 Micron / Openings 0.078 inch
Optional .039 and .059 inch openings available
Furnished with Plug as Standard.
SS 303 or Titanium
DD
D
C CC
B BB
Dimensions
Strainer Size (inches)
1 12
2 12
A 150 ANSI
AA 300 ANSI
B 150 ANSI
BB 300 ANSI
C Max. 150 ANSI
CC Max. 300 ANSI
D Dia. 150 ANSI
DD Dia. 300 ANSI
9.06
9.13
3.26
3.26
3.78
5.20
7.87
7.99
114
33
9.06
9.13
3.26
3.26
3.78
5.20
7.87
7.99
114
36
9.06
9.13
3.66
3.66
3.78
5.35
7.87
7.99
114
39
40
230
232
83
83
96
132
200
203
114
15
50
230
232
83
83
96
132
200
203
114
16
65
230
232
93
93
96
136
200
203
114
18
G Drain/Blow-off Plug
Approx. Ship Wt. Lbs.
CLA-VAL
10
100
300
302
110
110
150
158
235
238
114
33
150
400
402
143
143
191
203
400
403
114
65
200
500
502
170
170
224
237
460
463
114
96
250
580
582
225
225
295
325
560
563
114
196
12
14
16
18
20
24
24.02
24.09
8.88
9.56
15.16
15.67
26.77
26.85
2
626
25.59
25.67
10.24
10.94
14.96
15.67
26.77
26.85
2
683
31.50
31.57
12.20
12.20
19.69
19.69
35.43
35.43
2
970
31.50
31.57
13.18
13.18
19.69
19.69
35.43
35.43
2
1073
37.40
37.48
19.09
19.09
23.98
23.98
46.85
46.85
3
1175
43.31
43.39
19.09
19.09
23.98
23.98
46.85
46.85
3
1962
300
610
612
228
243
385
398
680
682
2
284
350
650
652
260
278
380
398
680
682
2
310
400
800
802
310
310
500
500
900
900
2
440
450
800
802
335
335
500
500
900
900
2
600
500
950
952
485
485
609
609
1190
1190
3
810
600
1100
1102
485
486
609
609
1190
1190
3
890
1701 Placentia Avenue Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com Website cla-val.com
Copyright Cla-Val 2016 Printed in USA Specifications subject to change without notice.
E-X43HL (R-09/2016)
33
X43HL
MODEL
Now available up to
48-inches/1200 mm
10 12 141620
24
Constant Downstream
Pressure
/2
10
1
100
CV (Gal/Min. - gpm.)
CV (Litres/Sec - l/s.)
1,000
1 12
96
23
2
150
36
2 12
254
61
3
367
85
4
654
157
6
1644
395
8
3922
702
Cv in gpm = gpm @ 1psid head loss Cv in l/s = l/s @ 1bar head loss
34
Flow (gpm)
10,000
100,000 200,000
CV Factor
Strainer Size (inches)
18
11
2 1/
10
4566
1097
12
6800
1580
14
16
18
20
24
8949 11692 12796 18264 26302
2150 2809 3555 4388 6319
Specifications
Sizes (Inches):
Sizes (mm):
Ends:
Max Pressure Rating:
Fluids:
Temperature:
Materials:
Body & Cover:
Cover Seal:
Strainer:
Strainer Mesh Sizes:
Drain/Blow-Off Connection:
Bolts:
112, 2, 212, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24, 36 and 48
40, 50, 65, 80,100, 150, 200, 250, 300, 350, 400, 450, 500, 600, 900 and 1200
Flanged, ANSI Class 150 and 300 (Note: 300# Flanges are Raised Face)
150 - 250 psi 300 - 400 psi
Compatible with Materials of Construction
Maximum 180F
Ductile Iron ANSI B16.62; Fusion Bonded Epoxy Coating Standard or
NiAIBrz ASTM B148
Buna-N Synthetic Rubber
316 Stainless Steel; Ductile Iron, Epoxy Coated Frame or in
Titanium on a NiAIBrz Frame
Standard 10 mesh / 2000 Micron / Openings 0.078 inch
Optional .039 and .059 inch openings available
Furnished with Plug as Standard.
SS 303 or Titanium
DD
D
Please consult factory to
confirm dimensional data for
36-inch/900 mm and
48-inch/1200 mm sizes
C CC
B BB
Dimensions
Strainer Size (inches)
1 12
2 12
A 150 ANSI
AA 300 ANSI
B 150 ANSI
BB 300 ANSI
C Max. 150 ANSI
CC Max. 300 ANSI
D Dia. 150 ANSI
DD Dia. 300 ANSI
9.06
9.13
3.26
3.26
3.78
5.20
7.87
7.99
114
33
9.06
9.13
3.26
3.26
3.78
5.20
7.87
7.99
114
36
9.06
9.13
3.66
3.66
3.78
5.35
7.87
7.99
114
39
40
230
232
83
83
96
132
200
203
114
15
50
230
232
83
83
96
132
200
203
114
16
65
230
232
93
93
96
136
200
203
114
18
G Drain/Blow-off Plug
Approx. Ship Wt. Lbs.
CLA-VAL
10
100
300
302
110
110
150
158
235
238
114
33
150
400
402
143
143
191
203
400
403
114
65
200
500
502
170
170
224
237
460
463
114
96
250
580
582
225
225
295
325
560
563
114
196
12
14
16
18
20
24
24.02
24.09
8.88
9.56
15.16
15.67
26.77
26.85
2
626
25.59
25.67
10.24
10.94
14.96
15.67
26.77
26.85
2
683
31.50
31.57
12.20
12.20
19.69
19.69
35.43
35.43
2
970
31.50
31.57
13.18
13.18
19.69
19.69
35.43
35.43
2
1073
37.40
37.48
19.09
19.09
23.98
23.98
46.85
46.85
3
1175
43.31
43.39
19.09
19.09
23.98
23.98
46.85
46.85
3
1962
300
610
612
228
243
385
398
680
682
2
284
350
650
652
260
278
380
398
680
682
2
310
400
800
802
310
310
500
500
900
900
2
440
450
800
802
335
335
500
500
900
900
2
600
500
950
952
485
485
609
609
1190
1190
3
810
600
1100
1102
485
486
609
609
1190
1190
3
890
1701 Placentia Avenue Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com Website cla-val.com
Copyright Cla-Val 2016 Printed in USA Specifications subject to change without notice.
E-X43HL (R-09/2016)
35
Solid Performer
Cla-Val Model X43HL H-Style Strainer
The durable Cla-Val Model X43HLH-Style Strainer is the easiest and most cost
effective way to protect piping and equipment from damage caused by pipeline
debris. Its large flow area and durable materials of construction means it can withstand the harsh conditions often encountered in refinery and offshore applications.
The body port allows for installation of a manual flush valve to clear small amounts
of debris from the strainer without removing the cover. For more thorough cleaning,
the top cover can easily be removed without taking strainer out of the pipeline.
Product Advantages
The X43HLStrainer provides many product advantages that make it an easy choice when considering the
most effective means to protect your system from pipeline debris.
Available in nickel aluminum bronze with titanium strainer mesh or fusion-bonded epoxy coated ductile
iron with 316 Stainless Steel strainer mesh
Compact profile requires less space than a wye-style strainer which typically has a body configuration
that extends well below the pipeline
Low pressure drop
Equipped with a plug on both sides of the unit that can be used as drain or flush valves
Available in 150# class in sizes 2 through 24
Lower cost than most other available strainers
Backed by the assurance that comes from using the most trusted products in the industry
Pressure
Reducing Valves
Pressure
Relief Valves
Fire Pump
Relief Valve
Air Release
Valve
Silent Wafer
Check Valve
Pump Suction
Control Valve
LLED B
Y
LAB
LAB
CANADA
OF
U N D E R W RIT
ULC
O R AT O
RI
ASSE
tems. Pilot controlled, it maintains constant system pressure at the pump discharge within very close limits as
demands change. The 50B-4KG1 and 2050B-4KG1 can be
SSED
Type Approved
Typical Application
KOModel 2050B-4KG1
Pressure Relief Valve
(Angle Pattern)
Operation Sequence
At pump start, Cla-Val Relief Valve modulates to relieve
excess pump capacity, maintaining positive system pressure at the pump discharge.
When fire demand slows or ceases, Cla-Val Model
50B-4KG1 opens, diverting entire pump output to discharge, allowing fire pump to be stopped without causing
surging in the lines.
Fire Pump
Check Valve
Specifications
Dimensions
2-1/2
Threaded Ends
9.38
11.00
12.50
---
---
---
---
A 150 Flanged
9.38
11.00
12.00
15.00
20.00
25.38
29.75
300 Flanged
10.00
11.62
13.25
15.62
21.00
26.38
31.12
12.88
15.31
20.56
25.88
30.44
(inches)
300 X 150
Purchase Specifications
The Fire Pump Pressure Relief Valve shall modulate to relieve excess
pressure in a fire protection system. It shall maintain constant pressure
in the system regardless of demand changes. It shall be pilot controlled
and back pressure shall not affect its set point. It shall be actuated by
line pressure through a pilot control system and open fast in order to
maintain steady system pressure as system demand decreases. It shall
close gradually to control surges and shall re-seat drip-tight within 5% of
its pressure setting. The main valve shall be of the hydraulically-operated, pilot-controlled, diaphragm-type, globe or angle valve. It shall have
a single, removable, teflon-coated seat, a grooved stem guided at both
ends, and a resilient disc with a rectangular cross section, being contained on 3 1/2 sides. No external packing glands shall be permitted and
the diaphragm shall not be used as a seating surface. The pilot control
shall be a direct-acting, adjustable, spring-loaded, diaphragm-type valve
designed for modulating service to permit flow when controlling pressure
exceeds spring setting. This valve shall be UL Listed and Factory Mutual
approved. It shall be the Model 50B-4KG1 (globe) or Model 2050B4KG1 (angle) Pressure Relief Valve as manufactured by Cla-Val Newport
Beach, California.
*Special Note:
The Model 50B-4KG1 Pressure Relief Valve is available with 300# ANSI
inlet flange and 150# ANSI outlet flange. This valve is used on higher
pressure systems where 300# flange connections are required, and
allows for adapting of a discharge cone (generally supplied with 150#
flange) to accommodate "atmospheric break" at relief valve discharge.
This relief valve, with 300# / 150# flanges is available on special order,
and is UNDERWRITERS LABORATORIES LISTED AND FACTORY
MUTUAL APPROVED.
Sizes
10
3.31
4.00
4.56
5.75
7.88
10.00
11.81
12.00
12.25
12.50
13.00
14.31
16.31
18.00
1.50
1.69
2.66
3.19
4.31
5.31
9.25
Threaded Ends
4.75
5.50
6.25
---
---
---
---
E 150 Flanged
4.75
5.50
6.00
7.50
10.00
12.75
14.88
300 Flanged
15.56
5.00
5.88
6.38
7.88
10.50
13.25
Threaded Ends
3.25
4.00
4.50
---
---
---
---
F 150 Flanged
3.25
4.00
4.00
5.00
6.00
8.00
8.62
300 Flanged
3.50
4.31
4.38
5.31
6.50
8.50
9.31
6.00
6.69
7.75
7.88
8.50
9.75
13.25
250
G&H
Valve Size
50
65
80
100
150
200
Threaded Ends
238
279
318
---
---
---
---
A 150 Flanged
234
279
305
381
508
645
756
300 Flanged
254
295
337
397
533
670
790
300 X 150
---
---
327
389
522
657
773
84
102
116
146
200
254
300
305
311
1318
330
363
414
457
38
43
65
81
109
135
235
Threaded Ends
121
140
159
---
---
---
---
E 150 Flanged
121
140
152
191
254
324
378
300 Flanged
395
(mm)
127
149
162
200
267
337
Threaded Ends
83
102
114
---
---
---
---
F 150 Flanged
83
102
102
127
152
203
219
89
109
111
135
165
216
236
152
170
197
200
216
248
337
300 Flanged
G&H
Valve Capacity
Valve Sizes in Inches:
2"
2 1/2"
208
300
3"
4"
6"
8"
10"
NFPA 20 Maximum
Recommended GPM
CLA-VAL
Represented By:
E-50B-4KG1/2050B-4KGL1 (R-04/2015)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
CLA-VAL UK
39
LAB
CANADA
OF
ULC
U N D E R W RIT
O R AT O
RI
DESIGN
ASSE
SSED
Type Approved
2050B-4KG1KOL (Angle)
Typical Applications
Offshore Platform Pump Relief
40
Specifications
Dimensions
Sizes
End Details
Pressure Ratings
Class 150 - 250 psi Max; Class 300 - 300 psi Max
Optional Coating
Main Valve Body & Cover: Ductile Iron ASTM A536 Grade 65-45-12
Main Valve Trim: Teflon Coated Stainless Seat, Stainless Steel Stem
Pilot Control System: Cast Bronze with Stainless Steel Trim
Purchase Specifications
The Fire Pump Pressure Relief Valve shall modulate to relieve excess
pressure in a fire protection system, maintaining constant pressure in the
system regardless of demand changes. It shall be pilot controlled and
back pressure shall not affect its set point. It shall be actuated by line
pressure through a pilot control system and open fast in order to maintain
steady system pressure as system demand decreases. It shall close
gradually to control surges and shall re-seat drip-tight within 5% of its pressure setting.
3"
4"
6"
8"
10"
12.50
---
---
---
---
(inches)
Threaded Ends
A 150 Flanged
12.00
15.00
20.00
25.38
29.75
300 Flanged
13.25
15.62
21.00
26.38
31.12
300 X 150
30.44
12.88
15.31
20.56
25.88
4.56
5.75
7.88
10.00
11.81
12.50
13.00
14.31
16.31
18.00
2.66
3.19
4.31
5.31
9.25
Threaded Ends
6.25
---
---
---
---
E 150 Flanged
6.00
7.50
10.00
12.75
14.88
300 Flanged
15.56
6.38
7.88
10.50
13.25
Threaded Ends
4.50
---
---
---
---
F 150 Flanged
4.00
5.00
6.00
8.00
8.62
300 Flanged
4.38
5.31
6.50
8.50
9.31
7.75
7.88
8.50
9.75
13.25
250
G&H
80
100
150
200
Valve Size
Threaded Ends
318
---
---
---
---
A 150 Flanged
305
381
508
645
756
300 Flanged
337
397
533
670
790
300 X 150
327
389
522
657
773
116
146
200
254
300
1318
330
363
414
457
235
Threaded Ends
*Special Note:
The Model 50B-4KG1KOL/2050B-4KG1KOL Pressure Relief Valve is
available with 300# ANSI inlet flange and 150# ANSI outlet flange for high
pressure systems where 300# flange connections are required, to allow
for adapting of a discharge cone (generally supplied with 150# flange) to
accommodate "atmospheric break" at relief valve discharge.
This relief valve, with 300# / 150# flanges is available on special order, and
is UNDERWRITERS LABORATORIES LISTED AND FACTORY MUTUAL
APPROVED.
F 150 Flanged
(mm)
65
81
109
135
Threaded Ends
159
---
---
---
---
E 150 Flanged
152
191
254
324
378
300 Flanged
162
200
267
337
395
114
---
---
---
---
102
127
152
203
219
111
135
165
216
236
197
200
216
248
337
300 Flanged
G&H
Valve Capacity
Valve Sizes in Inches:
3"
4"
6"
8"
10"
NFPA 20 Maximum
Recommended GPM
500
1000
2500
4000
11000
CLA-VAL
Represented By:
E-50B-4KG1KOL/2050B-4KG1KOL (R-04/2015)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
CLA-VAL UK
41
50B-5KG
MODEL
50B-5KG
Specifications
Typical Installation
When there is a demand in the Fire System, the pump is started,
delivering water from the supply source to the area of demand. To
assure that the fire pump draw does not exceed the available water
supply, the Model 50B-5KG, sensing the pump suction, modulates
to prevent suction pressure from dropping below a pre-set minimum.
By maintaining minimum pressure requirements in the supply main,
the main is protected from possible damage or backflow conditions.
Also, a minimum supply pressure is provided for local fire apparatus.
Sizes
End Details
Pressure Ratings
Temperature Range
Materials
TO
FIRE SERVICE
SYSTEM
NE
NG LI
NSI
OTE SE
REM
UMP
EP
FIR
SUPPLY SYSTEM
42
KG
B-5
L 50
-VA
CLA
Adjustment Range
Flow Chart
(MAX.)
3"
40
4"
6"
8"
30
25
20
15
10
8
6
4
3
INLET
OUTLET
2
1.5
CC
40
60
80 100
150
200
300
400
600
3000 4000
DD
BB
AA
(4" SIZE VALVE SHOWN)
Item
No.
1
2
3
4
5
6
Description
100KCGVX Hytrol (Main Valve)
CRL5A Pressure Relief Control
X44A Strainer and Orifice Assembly
CV Flow Control (Opening)
X101C Valve Position Indicator
CK2 (Blow-Off Valve)
VALVE
SIZE
3
4
6
8
(MAX.)
AA
BB
CC
12.00
15.00
20.00
25.38
13.25
15.62
21.00
26.38
6.00
7.50
10.00
12.75
6.38
7.88
10.50
13.25
4.00
5.00
6.00
8.00
4.38
5.31
6.50
8.50
300 LB.
150 LB.
150 LB.
300 LB.
150 LB.
300 LB.
FLANGES FLANGES FLANGES FLANGES FLANGES FLANGES
Purchase Specifications
The Fire Pump Suction Control Valve shall modulate to maintain a minimum pressure at the pump suction regardless of
system demand. It shall control the pump discharge in relation to the suction head available, and shall not allow suction
head pressure to fall below a pre-set minimum.
It shall be actuated by line pressure through a pilot control system which allows rapid response to changing pressure conditions without line surges. The pilot control shall be remote
sensed to the pump suction head pressure.
The main valve shall be of the hydraulically-operated, pilotcontrolled, diaphragm-type, globe or angle valve. It shall have
a single removable seat, a delrin-sleeved guided stem and a
renewable resilient synthetic rubber disc with a rectangular
cross section, contained on three and one-half sides by a disc
DD
50B-5KG (R-11/2010)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
13.50
15.00
16.50
20.00
4.62
5.75
7.88
10.00
2.56
3.19
4.31
5.31
CLA-VAL
(MAX.) (MAX.)
(TYP.)
(TYP.) (MAX.)
150 LB.
300 LB.
FLANGES FLANGES
(MIN.)
(MIN.)
.75
15.75
1.12
.94
17.75
1.25
1.00
20.25
1.44
1.12
23.00
1.62
Represented By:
CLA-VAL UK
43
50-20
MODEL
50A-20 (Angle)
REMOTE SENSING
2
Schematic Diagram
Item Description
1
2
3
4
Optional Features
Item Description
B
C
F
H
S
DRAIN TO
ATMOSPHERE
OUTLET
INLET
Specification
Sizes:
Temperature
Range:
44
Materials:
Adjustment
Ranges:
B (Diameter)
100S/2100S
H
Threaded &
Flanged
B (Diameter)
100S/2100S
Grooved
K
(MAX)
Inlet
CC
(MAX)
Outlet
Inlet
G
GG
GGG
EE
GGGG
D
DD
DDD
Inlet
A
AA
AAA
Inlet
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
0.4
15
25
184
143
140
83
29
48
.375
.25
.375
10
7
1 1/4 1 1/2
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
0.4
15
7.25
8.50
9.00
8.50
5.62
5.50
4.75
3.25
4.00
4.25
1.12
2.00
2.50
3.06
1.88
4.00
4.25
.375
.25
.375
0.4
15
9.38
9.38
10.00
9.00
6.62
6.50
5.75
4.75
4.75
5.00
4.75
1.50
2.50
3.00
3.25
3.25
3.25
3.50
3.25
.375
.50
.375
0.6
35
2 1/2
11.00
11.00
11.62
11.00
8.00
7.56
6.88
5.50
5.50
5.88
1.69
2.88
3.50
3.75
4.00
4.00
4.31
.50
.50
.50
0.7
50
12.50
12.00
13.25
12.50
9.12
8.19
7.25
6.25
6.00
6.38
6.00
2.06
3.12
3.75
4.13
4.50
4.00
4.38
4.25
.50
.50
.50
0.8
70
15.00
15.62
15.00
11.50
10.62
9.31
7.50
7.88
7.50
3.19
4.25
4.50
5.00
5.00
5.31
5.00
.75
.75
.75
1.1
140
20.00
21.00
20.00
15.75
13.38
12.12
10.00
10.50
4.31
6.00
5.50
6.25
6.00
6.50
.75
.75
.75
1.7
285
25.38
26.38
25.38
20.00
16.00
14.62
12.69
13.25
5.31
7.56
6.75
7.50
8.00
8.50
1
1
1
2.3
500
29.75
31.12
23.62
17.12
14.88
15.56
9.25
8.00
8.75
8.62
9.31
1
1
1
2.8
780
34.00
35.50
28.00
20.88
17.00
17.75
10.75
9.50
10.25
13.75
14.50
1
1.25
1
3.4
1165
32
184
143
140
120
83
29
48
.375
.25
.375
10
7
40
184
216
229
216
143
140
120
83
102
108
29
52
64
78
48
102
102
.375
.25
.375
10
7
50
238
238
254
228
168
165
146
121
121
127
121
38
64
76
83
83
83
89
83
.375
.50
.375
15
16
65
279
279
295
279
203
192
175
140
140
149
43
73
89
95
102
102
110
.50
.50
.50
18
23
80
318
305
337
318
232
208
184
159
152
162
152
52
79
95
105
114
102
111
108
.50
.50
.50
20
32
100
381
397
381
292
270
236
191
200
191
81
108
114
127
127
135
127
.75
.75
.75
28
64
150
508
533
508
400
340
308
254
267
110
152
140
159
152
165
.75
.75
.75
43
129
200
645
670
645
508
406
371
322
337
135
192
171
191
203
216
1
1
1
58
227
250
756
790
600
435
378
395
235
203
222
219
236
1
1
1
71
354
300
864
902
711
530
432
451
273
241
260
349
368
1
1.25
1
86
528
1 1/4 1 1/2
93
125
210 280
Purchase Specifications
2
210
470
10
12
14
39.00
40.50
32.75
24.19
19.50
20.25
12.62
10.50
11.50
14.88
15.62
1
1.5
1
4.0
1600
350
991
1029
832
614
495
514
321
267
292
378
397
1
1.5
1
102
726
16
41.38
43.50
35.50
25.00
20.81
21.62
15.50
11.75
12.75
15.69
16.50
1
2
1
4.5
2265
400
1051
1105
902
635
528
549
394
298
324
399
419
1
2
1
114
1027
18
46.00
47.64
41.50
39.06
12.95
15.00
15.00
1
1.5
1
5.1
2982
20
52.00
53.62
45.00
41.90
15.00
16.50
16.50
1
1.5
1
5.63
3900
24
61.50
63.24
53.16
43.93
30.75
31.62
17.75
19.25
19.25
22.06
22.90
1
1.5
1
6.75
6200
30
63.00 76.00
64.50 76.00
56.00 66.00
54.60 61.50
21.31 24.56
22.50 25.60
24.00 25.60
2
2
2
2
2
2
7.5
8.5
7703 11720
36
450
1168
1210
1054
992
329
381
381
1
1.5
1
130
1353
500
1321
1362
1143
1064
381
419
419
1
1.5
1
143
1769
600
1562
1606
1350
1116
781
803
451
489
489
560
582
1
1.5
1
171
2812
750
1600
1638
1422
1387
541
572
610
2
2
2
190
3494
900
1930
1930
1676
1562
624
650
650
2
2
2
216
5316
2 1/2
3
4
6
8
10
12
14
16
18
20
24
30
36
300 460 800 1800 3100 4900 7000 8400 11000 14000 17000 25000 42000 50000
670 1000 1800 4000 7000 11000 16000 19000 25000 31000 39000 56500 63000 85000
The Fire Pump Pressure Relief Valve shall modulate to relieve excess pressure
in a fire protection system. It shall maintain constant pressure in the system
regardless of demand changes. It shall be pilot controlled and back pressure
shall not affect its set point. It shall be actuated by line pressure through a pilot
control system and open fast in order to maintain steady system pressure as
system demand decreases. It shall close gradually to control surges and shall
re-seat drip-tight within 5% of its pressure setting. The main valve shall be of
the hydraulically-operated, pilot-controlled, diaphragm-type, globe or angle
valve. It shall have a single, removable, teflon-coated seat. Internal and exter-
CLA-VAL
DDDD
AAAA
Valve Capacity
Outlet
F
FF
1701 Placentia Avenue Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com Website cla-val.com
Copyright Cla-Val 2016 Printed in USA Specifications subject to change without notice.
E-50-20 (R-7/2011)
45
50-49
MODEL
DESIGN
ASSE
SSED
Type Approved
50A-49
Operation:
The Model 50-49 has both a normally open and normally
closed pilot controls. The valve mounts on a pipe tee at the
pump discharge and provides pipeline protection at pump
start-up through the normally open pilot control. This pilot will
be open to vent the relief valve cover chamber and enable the
relief valve to be open at pump start. When the pump first
starts, the relief valve relieves both air and start-up water pressure to atmosphere and protects the pump discharge piping
from accelerated pressure spikes. The spring loaded pilot with
adjustable spring range will slowly close and divert the system
pressure into system eliminating unsafe pressure spikes which
can damage or rupture discharge piping.
B1
Schematic Diagram
Optional Features
Item
1
2
3
4
5
6
Item Description
B CK2 (Isolation Valves)
C CV Flow Control (Closing)
Description
100S/2100S Hytrol (Main Valve)
CRL Pressure Relief Control
X44A Strainer & Orifice Assy
81-01 Check Valve
CRA Pressure Reducing Control
CNA Needle Valve (Opening)
Materials:
Main Valve Body & Cover:
Ductile Iron ASTM A-536
Cast Steel ASTM A216-WCB
Naval Bronze ASTM B61
Stainless Steel ASTM A743-CF-8M
Ni. AL. Bronze ASTM B148
50-49/2050-49
Shut-Off
System
46
581
Check Valve
FLOW
Blow-Off
Tee and
Valve
Main
Gate
Valve
B (Diameter)
100S/2100S
H
Threaded &
Flanged
B (Diameter)
100S/2100S
Grooved
CC
(MAX)
(MAX)
Inlet
Outlet
G
GG
GGG
Outlet
F
FF
EE
GGGG
D
DD
DDD
Inlet
A
AA
AAA
Valve Size (Inches)
A Threaded
AA 150 ANSI
AAA 300 ANSI
AAAA Grooved End
B Dia.
C Max.
CC Max. Grooved End
D Threaded
DD 150 ANSI
DDD 300 ANSI
DDDD Grooved End
E
EE Grooved End
F 150 ANSI
FF 300 ANSI
G Threaded
GG 150 ANSI
GGG 300 ANSI
GGGG Grooved End
H NPT Body Tapping
J NPT Cover Center Plug
K NPT Cover Tapping
Stem Travel
Approx. Ship Wt. Lbs.
Inlet
1
7.25
5.62
5.50
3.25
1.12
1.88
.375
.25
.375
0.4
15
Inlet
DDDD
AAAA
1 1/4 1 1/2
7.25 7.25
8.50
9.00
8.50
5.62 5.62
5.50 5.50
4.75
3.25 3.25
4.00
4.25
1.12 1.12
2.00
2.50
3.06
1.88 1.88
4.00
4.25
.375 .375
.25
.25
.375 .375
0.4
0.4
15
15
2
9.38
9.38
10.00
9.00
6.62
6.50
5.75
4.75
4.75
5.00
4.75
1.50
2.50
3.00
3.25
3.25
3.25
3.50
3.25
.375
.50
.375
0.6
35
2 1/2
11.00
11.00
11.62
11.00
8.00
7.56
6.88
5.50
5.50
5.88
1.69
2.88
3.50
3.75
4.00
4.00
4.31
.50
.50
.50
0.7
50
3
12.50
12.00
13.25
12.50
9.12
8.19
7.25
6.25
6.00
6.38
6.00
2.06
3.12
3.75
4.13
4.50
4.00
4.38
4.25
.50
.50
.50
0.8
70
15.00
15.62
15.00
11.50
10.62
9.31
7.50
7.88
7.50
3.19
4.25
4.50
5.00
5.00
5.31
5.00
.75
.75
.75
1.1
140
20.00
21.00
20.00
15.75
13.38
12.12
10.00
10.50
4.31
6.00
5.50
6.25
6.00
6.50
.75
.75
.75
1.7
285
25.38
26.38
25.38
20.00
16.00
14.62
12.69
13.25
5.31
7.56
6.75
7.50
8.00
8.50
1
1
1
2.3
500
10
29.75
31.12
23.62
17.12
14.88
15.56
9.25
8.00
8.75
8.62
9.31
1
1
1
2.8
780
12
34.00
35.50
28.00
20.88
17.00
17.75
10.75
9.50
10.25
13.75
14.50
1
1.25
1
3.4
1165
14
39.00
40.50
32.75
24.19
19.50
20.25
12.62
10.50
11.50
14.88
15.62
1
1.5
1
4.0
1600
16
41.38
43.50
35.50
25.00
20.81
21.62
15.50
11.75
12.75
15.69
16.50
1
2
1
4.5
2265
18
46.00
47.64
41.50
39.06
12.95
15.00
15.00
1
1.5
1
5.1
2982
20
52.00
53.62
45.00
41.90
15.00
16.50
16.50
1
1.5
1
5.63
3900
24
61.50
63.24
53.16
43.93
30.75
31.62
17.75
19.25
19.25
22.06
22.90
1
1.5
1
6.75
6200
30
63.00
64.50
56.00
54.60
21.31
22.50
24.00
2
2
2
7.5
7703
36
76.00
76.00
66.00
61.50
24.56
25.60
25.60
2
2
2
8.5
11720
10
12
14
16
18
20
24
30
36
250
300
350
400
450
500
600
750
900
114
25
32
40
50
65
80
100
150
200
32
54
85
115
200
440
770 1245 1725 2300 3130 3725 5345 7655 10150 14020
Valve Size
CV
Factor
mm.
Angle Gal./Min.(gpm.) 27
Pattern Litres/Sec. (l/s.) 6.5
27
112
212
7.7
13
20
28
48
106
185
29
61
101
139
240
541
299
414
552
752
894
6.5
15
24
33
58
130
238
378
600
734
1008
Feet (ft.)
Equivalent Globe
Pattern Meters (m.)
Length
23
19
37
51
53
85
116
211
291
347
467
422
503
612
595
628
1181 2285
7.1
5.7
12
15.5
16
26
35
64
89
106
142
129
154
187
181
192
552
28
28
46
40
37
58
80
139
176
217
222*
238*
247*
8.7
8.7
14
12
11
18
25
43
54
66
68
73
75
Globe Pattern
6.1
3.6
5.9
5.6
4.6
6.0
5.9
6.2
6.1
5.8
6.1
5.0
5.2
5.2
4.6
4.0
5.3
7.8
Angle Pattern
4.4
4.4
7.1
4.4
3.3
4.1
4.1
4.1
3.7
3.6
2.9
2.8
2.6
of
Pipe
K
Factor
Fl. Oz
Liquid Displaced from U.S. Gal.
Cover Chamber
When Valve Opens ml
Litres
Valve Capacity
CLA-VAL
.02
.02
.02
.03
.04
.08
.17
.53
163
303
643
2.0
4.8
1 1/4 1 1/2
93
125
210 280
2
210
470
569
4.0
6.5
9.6
11
12
29
42
90
9.5
15.1
24.6
36.2
41.6
197
340
1.26 2.51
45.4 109.8
2 1/2
3
4
6
8
10
12
14
16
18
20
24
30
36
300 460 800 1800 3100 4900 7000 8400 11000 14000 17000 25000 42000 50000
670 1000 1800 4000 7000 11000 16000 19000 25000 31000 39000 56500 63000 85000
1701 Placentia Avenue Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com Website cla-val.com
Copyright Cla-Val 2016 Printed in USA Specifications subject to change without notice.
E-50-49 (R-04/2015)
47
750B-4KG1
MODEL
Operation Sequence
At pump start, the Cla-Val Pressure Relief Valve modulates
to relieve excess pump capacity, maintaining positive system pressure at the pump discharge.
When fire demand slows or ceases, the main valve opens,
diverting the entire pump output to discharge, allowing the
fire pump to be stopped without causing surging in the lines.
4
6
Material Specification
Body:
Liner:
Liner Retainer:
INLET
OUTLET
Pilot
Body:
Spring Cover:
Wetted Parts:
Accessories
Check Control:
Control Piping:
Y Strainer:
Control Fittings:
Brass*
Copper*
Bronze*
Brass*
1
2
3
4
5
6
Description
100-42 Roll Seal Main Valve
CRL5A Pressure Relief Control
X58A Restriction
81-01 Check Valve (125 psid max. reverse pressure)
X43 Y-Strainer
Pressure Gauge
3
4
3 9/16 4 1/8
5 7/8 7 3/8
3 1/4
4
7 1/2
14
7 1/2
14
2
2 7/8
4 3/8
2 1/2
4
4
50
73
111
64
1.81
2.72
1.81
5
80
90
149
83
3.63
4.54
3.63
6.35
10
12
6
8
5 1/4
18
21 5/8
10 7/8 14 3/8
9 13/16
13
15 1/4
9
11
5 1/2
16
19
11
13 1/2
17 1/2 20 1/2
12 1/2
15
1/2
1/2
3/8
3/8
190
290
58
115
250
375
87
155
100
105
187
102
10
6.35
10
6.35
11.80
Design Specification
Sizes:
Approvals:
Maximum Differential:
Reverse Pressure:
125 psid maximum
Temperature Range:
32 to 160 degrees F*
Flange Operating Pressure: Class 125-175 psi maximum
Class 150-275 psi maximum
Class 250-300 psi maximum
Class 300-720 psi maximum
*Temperature range depends on liner material. Higher differential pressure
ratings available.
"E" N.P.T.
"A" TYP.
150
200
250
300
133
276
365
457
549
249
229
279
330
387
140
279
343
406
483
318
381
445
521
10
13
13
30
54.43
89 151.50
41.73 72.57 116.57 191
-
Performance Specification
Capacity:
Cf Factor:
Cavitation:
Rangeability:
Bearing Friction:
3/8" N.P.T.
3 PORTS
FLOW
"D"
"BB" DIA.
DIA.
"E" N.P.T.
"E" N.P.T.
"B"
DIA.
"CC"
"C"
When Ordering
Please Specify
1. Catalog No. 750B-4KG1
2. Valve Size
Purchase Specification
The Fire Pump Pressure Relief Valve shall modulate to relieve
excess pressure in a fire protection system. It shall maintain
constant pressure in the system regardless of demand changes.
It shall be pilot controlled and back pressure shall not affect its set
point. It shall be actuated by line pressure through a pilot control
system and open fast in order to maintain steady system pressure
as system demand decreases. It shall close gradually to control
surges and shall re-seat drip-tight within 5% of its pressure setting. This valve shall be UL Listed and Factory Mutual approved.
The control valve shall be constructed of a 316L stainless steel
body and only one moving part, an elastomeric liner or control
element. Minimum rangeability shall be 500:1 based on capacity
at flowing pressure conditions. Cf shall be greater than or equal
to 0.9. Valve and control system shall be similar in all respects to
Cla-Val Model 750B-4KG1 as manufactured by Cla-Val, Newport
Beach, California.
Represented By:
CLA-VAL
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
CLA-VAL UK
E-750B-4KG1 (01/2016)
49
850B-4
MODEL
The Cla-Val Model 850B-4 Fire Relief Valve is a pressure-operated, inline axial valve. A tube diaphragm actuates the valve, which is comprised of three major components: 1) Tube 2) Barrier and 3) Body. There
is only one moving part in the valve the tube diaphragm. There are
no shafts, packing, stem guides or springs.
The tube diaphragm is a one piece, homogeneous nitrile rubber part
which is extremely durable. The ends of the tube are thick solid rubber,
designed to fit between mating flanges. This design eliminates the possibility of cutting the tube diaphragm due to over tightening or piping misalignment during installation.
The tube forms a drip tight seal around the barrier when the pressure is
equalized between the valve inlet and the control chamber. When pressure is removed from the control chamber, the valve is open. The minimum recommended operating pressure is 40 P.S.I. of inlet pressure.
Principle of Operation
Inlet
Inlet
Outlet
FLOW
50
Outlet
FLOW
Inlet
Outlet
FLOW
Modulating Action
The valve tube diaphragm holds any intermediate position when a quantity of water
is exhausted from the control chamber via
the pilot. The quantity of water in the control chamber is established by the set
pressure of the pilot.
The control chamber is filled or
exhausted to atmosphere, maintaining set pressure.
Dimensions
Model 850B-4
"L"
T-2
T-1
T-1
"D"
T-1
T-1
T-2
3
8.75
7.5
1/4
1/2
67
4
9.75
9.5
1/4
1/2
99
80
222
191
1/4
1/2
30
100
248
241
1/4
1/2
45
Valve Sizes
NFPA 20 Maximum
Recommended GPM
MAIN VALVE
Ends:
Body:
Tube Diaphragm:
Barrier:
Bolts:
Pressure:
Temp. Range:
150
273
299
3/8
1/2
61
200
299
356
3/8
1/2
84
250
356
418
1/2
1/2
123
FLOW FACTORS
4, 6, 8 Factory
Mutual Approved
(with approved Pilot
Components)
Valve Capacity*
FLOW
6
10
8
10.75 11.75 14.00
11.75 14.00 16.44
3/8
1/2
3/8
1/2
1/2
1/2
135
270
185
3"
*Calculated
4"
6"
8"
KV
36.4
77.3
201
379
550
10"
3
4
Cla-Val 800 Series Control Valves operate with maximum efficiency when mounted in horizontal or vertical piping. Adequate space above and
around the valve for service personnel should be considered essential. A regular maintenance program should be established based on the specific
application data. However, we recommend a thorough inspection be done at least once a year. Consult factory for specific recommendations.
CLA-VAL
E-850B-4 (R-3/2011)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
51
850-20
MODEL
The Cla-Val Model 850-20 Seawater Relief Valve is a pressure-operated, in-line axial valve. A tube diaphragm actuates the valve, which is
comprised of three major components: 1) Tube 2) Barrier and 3) Body.
There is only one moving part in the valve the tube diaphragm.
There are no shafts, packing, stem guides or springs.
The tube diaphragm is a one piece, homogeneous nitrile rubber part
which is extremely durable. The ends of the tube are thick solid rubber,
designed to fit between mating flanges. This design eliminates the
possibility of cutting the tube diaphragm due to over tightening or piping misalignment during installation.
The tube forms a drip tight seal around the barrier when the pressure
is equalized between the valve inlet and the control chamber. When
pressure is removed from the control chamber, the valve is open. The
minimum recommended operating pressure is 40 P.S.I. of inlet pressure.
Principle of Operation
Inlet
Inlet
Inlet
Outlet
FLOW
52
Outlet
FLOW
Outlet
FLOW
Modulating Action
The valve tube diaphragm holds any intermediate position when a quantity of water
is exhausted from the control chamber via
the pilot. The quantity of water in the control chamber is established by the set
pressure of the pilot.
The control chamber is filled or
exhausted to atmosphere, maintaining set pressure.
Dimensions
Model 850-20
"L"
T-2
T-1
T-1
3
8.75
7.5
1/4
67
4
9.75
9.5
1/4
99
80
222
191
1/4
30
100
248
241
1/4
45
"D"
6
10
8
10.75 11.75 14.00
11.75 14.00 16.44
3/8
1/2
3/8
135
270
185
150
273
299
3/8
61
250
356
418
1/2
123
200
299
356
3/8
84
FLOW FACTORS
SIZE (IN) CV (gpm)
160
3
340
4
885
6
1667
8
2424
*10
T-1
T-1
T-2
Valve Capacity*
FLOW
Valve Sizes
3"
KV
36.4
77.3
201
379
550
* CALCULATED
4"
6"
8"
10"
NFPA 20 Maximum
500 1000 2500 5000 11000
Recommended GPM
MAIN VALVE
Ends:
Body:
Tube Diaphragm:
Barrier:
Bolts:
Pressure:
Temp. Range:
4 Gauge Connection
Bronze / Monel
Nitrile Rubber
Controls Pressure
Excursions within
3% of Set Point
30 to 200 PSIG
Normally Closed; Opens at
Set Pressure; Modulates
Cla-Val 800 Series Control Valves operate with maximum efficiency when mounted in horizontal or vertical piping. Adequate space above and
around the valve for service personnel should be considered essential. A regular maintenance program should be established based on the
specific application data. However, we recommend a thorough inspection be done at least once a year. Consult factory for specific recommendations.
CLA-VAL
E-850-20 (R-3/2011)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
53
750-20
MODEL
Schematic Diagram
Operation Sequence
6
5
(Please note that if the Model 750-20 is to be used on a continuous duty basis to maintain seawater fire system pressure,
suitable back pressure must be provided on the valve to prevent cavitation damage. Consult the factory for details.)
Body:
See below*
Liner:
Liner Retainer:
Pilot
Body:
Spring Cover:
Wetted Parts:
Accessories
Check Control:
Control Piping:
Control Fittings:
Roll Seal
Material Specification
INLET
Description
100-42 Roll Seal (Main Valve)
CRL Pressure Relief Control
X58A Restriction
81-01 Check Valve
X43B Y-Strainer
Pipe Tee (Gauge Port)
Pipe Plug
TM
OUTLET
"E" N.P.T.
"E" N.P.T.
"A" TYP.
"E" N.P.T.
"D"
DIA.
3/8" N.P.T.
3 PORTS
"BB"
DIA.
FLOW
"B"
DIA.
"CC"
"C"
Flanged Style
6', 8", 10", & 12" sizes
Wafer Style
2', 3", & 4" sizes
Performance Specification
Capacity:
Cf Factor:
Cavitation:
Rangeability:
Bearing Friction:
Design Specification
Sizes:
Maximum Differential:
Reverse Pressure:
Temperature Range:
2
278
-438
-212
---4
4
224
8
-1438
-11
-1312
15
3
8
115
155
3177
10
-18
-13
-16
1712
1
2
190
250
4964
12
-2158
-1514
-19
2012
1
2
290
375
7148
When Ordering,
Please Specify
1. Catalog No. 750-20
2. Valve Size
3. Fluid Being Handled
4. Fluid Temperature Range
5. Inlet Pressure Range
6. Outlet Pressure Range
CLA-VAL
E-750-20 (R-07/2014)
80
90
-149
-83
---3.63
4.54
3.63
6.35
30
6
514
1078
91316
9
512
11
1212
3
8
58
87
1787
Purchase Specification
50
73
-111
-64
---1.81
2.72
1.81
5
14
4
418
-738
-4
---14
14
794
CLA-VAL CANADA
3
3916
-578
-314
---712
712
469
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
7. Maximum Differential
Pressure
8. Minimum Differential
Pressure
9. Maximum Flow Rate
10. Pilot Set Point
Represented By:
CLA-VAL UK
55
MODEL
55L-60
outlet
inlet
100-300 psi
1 Size
20-75 psi
40-200 psi
100-300 psi
0-75 psi
20-200 psi
outlet
inlet
outlet
inlet
outlet
more materials
available
inlet
The Model 55L-60 is normally held closed by the force of the compression
spring above the diaphragm. When the controlling pressure applied under the
diaphragm exceeds the spring setting, the disc is lifted off its seat, permitting
flow through the control. When control pressure drops below the spring
setting, the spring forces the control back to its normally closed position. The
controlling pressure is applied to the chamber beneath the diaphragm
through an internal passage. A gauge port is provided for accurate pressure
setting.
Pressure adjustment is done by turning the adjusting screw to vary the spring
load on the diaphragm. The 55L-60 is available in pressure ranges suited to
agency approval tests. To prevent tampering, the adjustment cap can be wire
sealed by using the lock wire holes provided in the cap and cover.
55L-60
90-21 UL Listed
Pressure Reducing
Valves
55L-60
56
Specifications
Size
Temperature Range
Materials
Body & Cover:
Trim:
Rubber:
Pressure Ratings
Other Materials
1/8 NPT
Pressure
Gauge Port
6.75
9.24
1.31
1.31
2.00
0 to 75 psi
20 to 200 psi
3.50
(applies to both
configurations)
Valve Size
Cv
Factor
Max Flow
(GPM)
1/2"
25
3/4"
8.5
40
1"
12.8
65
A
3.12
4.00
Dimensions (1):
Spring Range:
20-75
40-200
100-300
8.51
10.33
4.13
CLA-VAL
E-55L-60 (R-07/2016)
CLA-VAL CANADA
4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone: 905-563-4963
Fax:
905-563-4040
E-mail sales@cla-val.ca
COPYRIGHT
CLA-VAL EUROPE
Chemin des Msanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax:
41-21-643-15-50
E-mail: cla-val@cla-val.ch
CLA-VAL UK
Dainton House, Goods Station Road
Tunbridge Wells
Kent TN1 2 DH England
Phone: 44-1892-514-400
Fax:
44-1892-543-423
E-mail: info@cla-val.co.uk
CLA-VAL FRANCE
Porte du Grand Lyon 1
ZAC du Champ du Prier
France - 01700 Neyron
Phone: 33-4-72-25-92-93
Fax: 33-4-72-25-04-17
E-mail: cla-val@cla-val.fr
CLA-VAL PACIFIC
45 Kennaway Road
Woolston, Christchurch, 8023
New Zealand
Phone: 64-39644860
www.cla-valpacific.com
E-mail: info@cla-valpacific.com
57
MODELS
MEA
Approved
Special System Water Control Valves Class II
UL Product Category VLMT File No. Ex 2534
Function
Cla-Val 90G-21 (globe) and 90A-21 (angle) Pressure
Reducing Valves automatically reduce a higher inlet
pressure to a steady lower outlet pressure regardless of
changing flow rate and/or varying inlet pressure. The
valves pilot control system is very sensitive to slight
downstream pressure fluctuations, and will automatically open or close to maintain the desired pressure setting.
The downstream pressure can be set over a wide range
by turning the adjustment screw on the CRD pilot control. The adjustment screw is protected by a screw-on
cover, which can be sealed to discourage tampering.
Schematic Diagram
Item
Description
1 100KX Hytrol Main Valve
2 X58C Restriction
Assembly
3 CRD Pressure Reducing
Control (see note)
4 X46A Flow Clean
Strainer
P Gauge Option
Note:
For Steel and Ductile Iron 300 Class Valves, use CRDKX with a special diaphragm
washer, yoke and screws (30- 165)
Typical Application
55L-60
90-21 UL Listed
Pressure Reducing
Valves
A relief valve of not less than 1/2 inch in size must also be installed on the
downstream side of the pressure control valve. Adequate drainage for the
relief valve discharge must be provided.
55L-60
UL / ULC Listings
58
Size
Ductile Iron
150#
Flanged
1 1/2''
2''
2 1/2''
3''
4''
6''
8''
10''
UL / ULC
UL / ULC
UL / ULC
UL / ULC
UL / ULC
UL / ULC
UL / ULC
ULC
Ductile Iron
300#
Screwed
UL /
UL /
UL /
UL /
ULC
ULC
ULC
ULC
Ductile Iron
300 #
Flanged
UL / ULC
UL / ULC
UL / ULC
UL / ULC
UL / ULC
UL / ULC
UL / ULC
ULC
Bronze
300#
Threaded
UL /
UL /
UL /
UL /
ULC
ULC
ULC
ULC
Bronze
150#
Flanged
Bronze
300#
Flanged
ULC
ULC
ULC
ULC
ULC
ULC
ULC
ULC
Cast Steel
Globe Pattern
300# Flanged Ductile Iron
Grooved End Grooved End
UL /
UL /
UL /
UL /
UL /
UL /
ULC
ULC
ULC
ULC
ULC
ULC
UL / ULC
UL / ULC
UL
UL / ULC
UL / ULC
UL / ULC
UL / ULC
Angle Pattern
Ductile Iron
Grooved End
UL / ULC
UL / ULC
UL / ULC
UL / ULC
Dimensions
Valve Size (Inches)
A Threaded
AA 150 ANSI
AAA 300 ANSI
AAAA Grooved End
B
BB Grooved End
C Max.
CC Max. Grooved End
D
DD Grooved End
E Threaded
EE 150 ANSI
EEE 300 ANSI
EEEE Grooved End
F Threaded
FF 150 ANSI
FFF 300 ANSI
FFFF Grooved End
G (Max)
GG (Max)
1 1/2
7.25
8.50
9.00
8.50
1.12
2.00
5.50
4.10
2.81
2.81
3.25
4.00
4.25
1.88
4.00
4.25
7.50
8.10
40
50
184
216
229
216
28
52
140
104
71
71
83
102
108
48
102
108
191
206
238
238
254
228
38
54
161
127
84
84
121
121
127
121
83
83
89
121
197
203
2
9.38
9.38
10.00
9.00
1.50
2.50
6.50
5.00
3.31
3.31
4.75
4.75
5.00
4.75
3.25
3.25
3.50
3.25
7.75
8.00
2 1/2
11.00
11.00
11.62
11.00
1.69
2.88
7.56
6.88
4.40
4.40
5.50
5.50
5.88
4.00
4.00
4.31
7.75
3
12.50
12.00
13.25
12.50
2.56
3.12
8.19
6.50
4.56
4.56
6.25
6.00
6.38
6.00
4.50
4.00
4.38
4.50
8.00
8.13
15.00
15.62
15.00
3.19
4.25
10.62
8.80
5.75
5.75
7.50
7.88
7.50
5.00
5.31
5.00
9.00
9.31
20.00
21.00
20.00
4.31
6.00
13.38
11.10
7.88
7.88
10.00
10.50
6.00
6.50
9.50
10.50
25.38
26.38
25.38
5.31.
7.56
16.00
14.50
10.00
10.00
12.75
13.25
8.00
8.50
10.50
11.50
10
29.75
31.12
9.25
17.12
11.81
14.88
15.56
8.62
9.31
11.50
65
80
100
150
200
250
279
279
295
279
43
64
192
175
102
102
140
140
149
102
102
109
197
318
305
337
318
65
79
208
165
116
116
159
152
162
152
114
102
111
114
203
207
381
397
381
81
105
270
223
146
146
191
200
191
127
135
127
228
236
508
533
508
109
152
340
281
200
200
254
267
152
165
241
267
645
670
645
135
184
406
369
254
254
324
349
203
216
267
292
756
790
235
435
378
395
217
236
292
GG
G
C
CC
(MAX)
Valve Size
112"
2"
212"
3"
4"
6"
8"
10"
Maximum
160
262
373
576
992
2251
3900
6150
Minimum
1
1
2
2
4
10
15
35
INLET
OUTLET
BB
A
AA
AAA
AAAA
4" SIZE
SHOWN
OUTLET
FFF
FF
FFFF
INLET
EE
EEE
EEEE
(MAX)
Selection Guidelines
Flow Capacity Table
DD
Class
UL
30-165
30-165
ULC
30-300
30-300
CLA-VAL
1701 Placentia Avenue Costa Mesa CA 92627 Phone: 949-722-4800
Fax: 949-548-5441 Web Site: cla-val.com E-mail: claval@cla-val.com
CLA-VAL CANADA
4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone: 905-563-4963
Fax:
905-563-4040
E-Mail: sales@cla-val.ca
E-90-21/90-21P (R-09/2016)
CLA-VAL EUROPE
CLA-VAL UK
Dainton House, Goods Station Road
GB - Tunbridge Wells
Kent TN1 2 DH England
Phone: 44-1892-514-400
Fax:
44-1892-543-423
E-Mail: info@cla-val.co.uk
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
59
90-42
MODEL
90G-42
Globe Pattern
Function
Cla-Val Model 90G-42 (globe) and 90A-42(angle)
Seawater Service Pressure Reducing Valves automatically reduce a higher inlet pressure to a steady Schematic Diagram
lower outlet pressure regardless of changing flow Item Description
rate and/or varying inlet pressure. The valves pilot
1
Model 100S/2100S
Hytrol (Globe or Angle)
control system is very sensitive to slight downstream pressure fluctuations, and will automatically
2
X58C Restriction Tube Fitting
open or close to maintain the desired pressure set3
CRD Pressure Reducing Control
ting. The downstream pressure can be set over a
4
X46A Flow Clean Strainer
wide range by turning the adjustment screw on the
CRD pilot control. The adjustment screw is protected by a screw-on cover, which can be sealed to discourage tampering.
Sizes:
60
Materials:
Adjustment
Ranges:
15 - 75 psi
30 - 300 psi
B (Diameter)
J
100-01
Threaded &
Flanged
Grooved
CC
(MAX)
Inlet
When Ordering
Please Specify
B (Diameter)
100-01
(MAX)
Outlet
Inlet
G
GG
GGG
Outlet
F
FF
EE
GGGG
D
DD
DDD
Inlet
A
AA
AAA
Inlet
DDDD
AAAA
7.25
7.50
5.62
5.50
3.25
1.12
2.12
1.88
.375
.25
.375
0.4
15
25
184
191
143
140
83
29
54
48
.375
.25
.375
10
7
1 1/4 1 1/2
7.25
8.00
5.62
5.50
3.25
1.12
2.25
1.88
.375
.25
.375
0.4
15
7.25
8.50
9.00
8.50
5.62
5.50
4.75
3.25
4.00
4.25
1.12
2.00
2.50
3.06
1.88
4.00
4.25
.375
.25
.375
0.4
15
9.38
9.38
10.00
9.00
6.62
6.50
5.75
4.75
4.75
5.00
4.75
1.50
2.50
3.00
3.25
3.25
3.25
3.50
3.25
.375
.50
.375
0.6
35
2 1/2
11.00
11.00
11.62
11.00
8.00
7.56
6.88
5.50
5.50
5.88
1.69
2.88
3.50
3.75
4.00
4.00
4.31
.50
.50
.50
0.7
50
12.50
12.00
13.25
12.50
9.12
8.19
7.25
6.25
6.00
6.38
6.00
2.06
3.12
3.75
4.13
4.50
4.00
4.38
4.25
.50
.50
.50
0.8
70
15.00
15.62
15.00
11.50
10.62
9.31
7.50
7.88
7.50
3.19
4.25
4.50
5.00
5.00
5.31
5.00
.75
.75
.75
1.1
140
20.00
21.00
20.00
15.75
13.38
12.12
10.00
10.50
4.31
6.00
5.50
6.25
6.00
6.50
.75
.75
.75
1.7
285
25.38
26.38
25.38
20.00
16.00
14.62
12.69
13.25
5.31
7.56
6.75
7.50
8.00
8.50
1
1
1
2.3
500
10
29.75
31.12
23.62
17.12
14.88
15.56
9.25
8.00
8.75
8.62
9.31
1
1
1
2.8
780
12
34.00
35.50
28.00
20.88
17.00
17.75
10.75
9.50
10.25
13.75
14.50
1
1.25
1
3.4
1165
32
184
203
143
140
120
83
29
57
48
.375
.25
.375
10
7
40
184
216
229
216
143
140
120
83
102
108
29
52
64
78
48
102
102
.375
.25
.375
10
7
50
238
238
254
228
168
165
146
121
121
127
121
38
64
76
83
83
83
89
83
.375
.50
.375
15
16
65
279
279
295
279
203
192
175
140
140
149
43
73
89
95
102
102
110
.50
.50
.50
18
23
80
318
305
337
318
232
208
184
159
152
162
152
52
79
95
105
114
102
111
108
.50
.50
.50
20
32
100
381
397
381
292
270
236
191
200
191
81
108
114
127
127
135
127
.75
.75
.75
28
64
150
508
533
508
400
340
308
254
267
110
152
140
159
152
165
.75
.75
.75
43
129
200
645
670
645
508
406
371
322
337
135
192
171
191
203
216
1
1
1
58
227
250
756
790
600
435
378
395
235
203
222
219
236
1
1
1
71
354
300
864
902
711
530
432
451
273
241
260
349
368
1
1.25
1
86
528
14
39.00
40.50
32.75
24.19
19.50
20.25
12.62
10.50
11.50
14.88
15.62
1
1.5
1
4.0
1600
350
991
1029
832
614
495
514
321
267
292
378
397
1
1.5
1
102
726
16
41.38
43.50
35.50
25.00
20.81
21.62
15.50
11.75
12.75
15.69
16.50
1
2
1
4.5
2265
400
1051
1105
902
635
528
549
394
298
324
399
419
1
2
1
114
1027
18
46.00
47.64
41.50
39.06
12.95
15.00
15.00
1
1.5
1
5.1
2982
20
52.00
53.62
45.00
41.90
15.00
16.50
16.50
1
1.5
1
5.63
3900
24
61.50
63.24
53.16
43.93
30.75
31.62
17.75
19.25
19.25
22.06
22.90
1
1.5
1
6.75
6200
30
63.00 76.00
64.50 76.00
56.00 66.00
54.60 61.50
21.31 24.56
22.50 25.60
24.00 25.60
2
2
2
2
2
2
7.5
8.5
7703 11720
36
450
1168
1210
1054
992
329
381
381
1
1.5
1
130
1353
500
1321
1362
1143
1064
381
419
419
1
1.5
1
143
1769
600
1562
1606
1350
1116
781
803
451
489
489
560
582
1
1.5
1
171
2812
750
1600
1638
1422
1387
541
572
610
2
2
2
190
3494
900
1930
1930
1676
1562
624
650
650
2
2
2
216
5316
Cla-Val Control Valves operate with maximum efficiency when mounted in horizontal piping with the main valve cover UP, however, other
positions are acceptable. Due to component size and weight of 8 inch and larger valves, installation with cover UP is advisable. We recommend isolation valves be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be considered essential. A regular maintenance program should be established based on the specific application data.
However, we recommend a thorough inspection be done at least once a year. Consult factory for specific recommendations.
114
112
212
10
12
14
16
18
20
24
30
36
100 125 160 262 373 576 992 2251 3900 6150 8720 10540 13700 17500 21700 31300 48000 62500
*For UL Listed, see Cla-Val Model 90-21 for sizes and pressure class information.
CLA-VAL
P.O. Box 1325 Newport Beach, CA 92659-0325 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: claval@cla-val.com Website cla-val.com
Copyright
E-90-42 (R-08/2014)
61
CLA-VAL VALVES
CAVITATION CHART
for water applications
Cavitation Guide
100-01/100-20
100S/2100S
100G/2100G
100GS/2100GS
Cavitation Zone
180
GUIDE ONLY
160
140
120
100
80
60
40
20
0
0
10
20
30
40
50
60
70
80
90
100 110
62
120 130
140
150
100S/100G/100GS/100-01
FLOW CHART
Valve Sizing Coefficient - Cv
A very useful expression often used in determining the head loss and/or flow rate capacity of control
valves is the Cv factor. Commonly referred to as the flow coefficient or valve sizing coefficient, this
empirically determined factor describes the flow capacity of a valve.
The Cv factor is defined as the number of U.S. gallons per minute of water (at 60F flowing temperature) discharged through a flow restriction with a head loss of one psi. In the case of a control valve,
the Cv value is normally stated for the valve in the fully open position. For conditions other than full
open, (i.e. modulating valves), contact Cla-Val Technical Services.
11/4 11/2
1/2
11/4
11/2
3/4
21/2
2
21/2
10
10
12 14
12 14
16
20 24
16 18
30 36
100
80
60
40
30
20
10
8
6
4
3
2
1
1
10
20
30 40
60 80 100
200
500
Flow Rate
1000
2000
5000
10,000
20,000
50,000 100,000
gpm (water)
NOTE: The flow rate vs. head loss data presented here is based on a fully open valve condition. The maximum
recommended velocity is 20 ft./sec.
CVFactors
Inches
114
112
212
15
20
25
32
40
50
65
8.5 13.3 30
32
54
85 115 200 440 770 1245 1725 2300 3130 3725 5345 7655 10150 14020
Litres/Sec. (l/s.)
13
20
Gal./Min. (gpm.)
29
Litres/Sec. (l/s.)
15
10
12
14
16
18
20
24
30
36
300
350
400
450
500
600
750
900
Valve Size
mm.
Globe
Pattern
CV
Factor
Angle
Pattern
10
24
28
33
414
600
552
752
734 1008
*Estimated
63
100
2"
3"
6"
4"
8"
12"
10
10
100
FLOW (GPM)
1000
10000
NOTE: The flow rate vs. head loss data presented here is based on a fully open valve condition. The maximum
recommended velocity is 20 ft./sec.
10"
2"
3"
4"
6"
8"
10"
12"
224
469
794
1787
3177
4964
7148
B
A
R
.69
.62
10
.55
.48
7
6
.28
P
S
I
"
10
Cavitation Zone
Maximum
Recommended
Flow
.41
.35
8"
20
4"
1.38
3"
30
6"
5
4
.21
.14
.07
22.7
45.4
68.1
100 X
90.8 113.6
9 1
454.3
159 204.4
136.3 182 227
1000 X
GPM
9 1
(M
H)
NOTE: The flow rate vs. head loss data presented here is based on a fully open valve condition. The maximum
recommended velocity is 20 ft./sec.
CV Factors
Valve
Size
3"
4"
6"
8"
10"
CV (gpm)
160
340
885
1667
2424
CV (KV)
36.36
77.27
201.01
378.62
550
* Calculated
65
MODEL
134-05
2
1
Schematic Diagram
E
LAB
CANADA
ULC
OF
Description
100G/2100G UL Listed Hytrol Main Valve
CS3 Solenoid Control
100-01 Hytrol Pilot Valve
X58C Restriction Orifice
X46A Flow Clean Strainer
U N D E R W RIT
Item
1
2
3
4
5
BLLED BY
LA
O R AT O
RI
F
INDEPENDENT
OPERATING
PRESSURE
INLET
OUTLET
5
Materials
Specifications
PRESSURE RATINGS
Cover Capacity
Functional Data
Valve Size
CV
Factor
66
Inches
10
12
Valve Size
Displacement
mm
80
100
150
200
250
300
.080 gal
115
200
440
770
1245 1725
.169 gal
27.6
48
105.6
184.8
299
.531 gal
139
240
541
990
1575 2500*
1.26 gal
33.4
58
130
238
378
10
2.51 gal
12
4.00 gal
414
600
INLET
OUTLET
OUTLET
INLET
Valve Size (In.)
10
12
80
100
150
200
250
A 150 ANSI
12.00
15.00
20.00
25.38
29.75
A 150 ANSI
305
381
508
645
756
AA 300 ANSI
13.25
15.62
21.00
26.38
31.12
34.00
AA 300 ANSI
337
397
533
670
791
864
B Dia.
9.12
11.50
15.75
20.00
23.62
35.50
B Dia.
232
292
400
508
600
902
C Max.
8.19
10.62
13.38
16.00
17.12
C Max.
208
270
340
406
435
2.56
3.19
4.31
5.16
8.50
28.00
65
81
110
131
216
711
E 150 ANSI
7.00
8.50
10.00
12.69
14.88
20.88
E 150 ANSI
178
216
254
322
378
530
--
8.81
10.50
13.19
--
EE 300 ANSI
--
224
267
350
--
4.00
4.97
6.00
8.00
8.62
F 150 ANSI
102
126
152
203
219
--
5.28
6.50
8.50
--
17.00
FF 300 ANSI
--
134
165
216
--
432
4.75
5.94
7.25
8.50
10.50
17.75
121
151
184
216
267
451
2.69
2.81
3.88
5.31
6.56
68
71
99
135
167
2.56
2.81
3.81
4.81
5.81
10.75
65
71
97
122
148
273
7.00
4.03
6.75
17.00
15.50
178
102
171
432
394
2.56
2.81
3.81
4.81
8.50
9.50
65
71
97
122
216
241
4.00
4.24
10.25
102
108
260
EE 300 ANSI
F 150 ANSI
FF 300 ANSI
1.75
2.41
2.75
N NPT
1/2 - 14
3/4 -14
3/4 - 14
P NPT
1-1/4 -11-1/2
1 - 11-1/2 1 -11-1/2
2 - 11-1/2
45
61
70
N NPT
1/2 - 14
3/4 - 14
3/4 -14
P NPT
1-1/4 -11-1/2
1 - 11 1/2 1 - 11-1/2
300
2 -11-1/2
R 150 ANSI
2.50
3.47
3.25
4.19
7.12
14.50
R 150 ANSI
64
88
83
106
181
368
RR 300 ANSI
3.12
3.78
3.75
4.69
7.81
RR 300 ANSI
79
96
95
119
198
X Pilot System
15.00
17.00
29.00
31.00
33.00
X Pilot System
381
432
737
787
838
Y Pilot System
11.00
12.00
20.00
22.00
24.00
1.25
Y Pilot System
279
305
508
559
610
1.25
Z Pilot System
11.00
12.00
20.00
22.00
24.00
Z Pilot System
279
305
508
559
610
Voltages:
110, 220 -50Hz AC
24, 120, 240, 480 - 60Hz AC
6, 12, 24, 120, 240 - DC
Others available at extra cost
Max. operating pressure differential: 200 psi
Coil:
Insulation molded Class
F
Watts AC
6
AC Volt Amps Inrush
30
AC Volt Amps Holding
16
Watts DC
10.6
Temperature Range
Water: to 180F
Fluids
Air, water, light oils
Rubber Parts
Buna-N Synthetic Rubber
Solenoid Control*
Body:
Brass ASTM B283
Enclosure:
NEMA Type 1, 2, 3, 3S, 4, 4X general purpose watertight
NEMA Type 6, 6P, 7, 9 watertight
Explosion Proof available at extra cost
134-05 (R-07/2016)
2. Valve Size
3. Pattern - Globe or Angle
4. Pressure Class
5. Threaded, Flanged or Grooved
6. Material Desired
7. Energized or De-energized to
Open Main Valve
CLA-VAL
8. Solenoid Enclosure,
When Ordering,
Please Specify
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
67
Control
O pOptional
t i o n a l Electric
Va l v e Tr
i m AArrangements
rrangements
134-30
134-60
CS3
(IN)
(EA)
2
(A)
Y
F
INDEPENDENT
OPERATING
PRESSURE
INLET
OUTLET
A
134-47
Latching
Solenoid
CS3
3
2
1
134-61
3
F
INDEPENDENT
OPERATING
PRESSURE
INLET
OUTLET
5
134-50
CS3
3
2
1
Latching
Solenoid
134-81
F
INDEPENDENT
OPERATING
PRESSURE
INLET
OUTLET
5
1
68
134-56
134-82
134-57
134-83
134 Series Solenoid Operated Deluge Valve used in Water Curtain Application
134-60
MODEL
134G-60
22
CS3
1
Schematic Diagram
(EA)
2
(A)
Item Description
1
2
3
4
5
Y
F
INDEPENDENT
OPERATING
PRESSURE
INLET
OUTLET
A
Specification
Inches
10
mm
80
100
150
200
250
115
200
440
770
1245
27.6
48
139
240
541
990
1575
33.4
58
130
238
378
Cv
Factor Angle Gal./Min. (gpm.)
Pattern Litres/Sec. (L/s)
70
105.6 184.8
299
Cover Capacity
Valve Size Displacement
3
.080 gal
4
.169 gal
6
.531 gal
8
1.26 gal
10
2.51 gal
2100GS (Angle)
100GS(Globe)
INLET
OUTLET
OUTLET
INLET
3
12.00
13.25
9.12
8.19
2.56
7.00
-4.00
-4.75
2.69
2.56
7.00
2.56
1.75
1/2-14
1-1/4-11
2.50
3.12
15.00
11.00
11.00
4
6
8
10
15.00
20.00
25.38
29.75
15.62
21.00
26.38
31.12
11.50
15.75
20.00
23.62
10.62
13.28
16.00
17.12
3.19
4.31
5.16
8.50
8.50
10.00
12.69
14.88
8.81
10.50
13.19
-4.97
6.00
8.00
8.62
5.28
6.50
8.50
-5.94
7.25
8.50
10.50
2.81
3.88
5.31
6.56
2.81
3.81
4.81
5.81
4.03
6.75
17.00
15.50
2.81
3.81
4.81
8.50
2.41
2.75
4.00
4.24
3/4-14 3/4-14 1-11 1/2 1-11 1/2
2-11 1/1/2
3.47
3.25
4.19
7.12
3.78
3.75
4.69
7.81
17.00
29.00
31.00
33.00
12.00
20.00
22.00
24.00
12.00
20.00
22.00
24.00
80
305
337
232
208
65
178
-102
-121
68
65
178
65
45
1/2-14
1-1/4-11
64
79
381
279
279
100
150
200
250
381
508
645
756
397
533
670
791
292
400
508
600
270
340
406
435
81
110
131
216
216
254
322
378
224
267
350
-126
152
203
219
134
165
216
-151
184
216
267
71
99
135
167
71
97
122
148
102
171
432
394
71
97
122
216
61
70
102
108
3/4-14 3/4-14 1-11 1/2 1-11 1/2
2-11 1/1/2
88
83
106
181
96
95
119
198
432
737
787
838
305
508
559
610
305
508
559
610
Temperature Range
Water: to 180F
Fluids
Air, water, light oils
Rubber Parts
Buna-N Synthetic Rubber
Solenoid Control*
Body:
316SS
Enclosure:
NEMA Type 1, 2, 3, 3S, 4, 4X general
Manual operator available at extra cost.
purpose watertight
NEMAType 6, 6P, 7, 9 watertight
Explosion Proof available at extra cost ULListed:3 - 10
*Optional material available for Seawater Service
CLA-VAL
When Ordering,
Please Specify
1. Catalog No. 134-60
2. Valve Size
3. Pattern - Globe or Angle
4. Pressure Class
5. Threaded, Flanged or Grooved
6. Material Desired
7. Energized or De-energized to
Open Main Valve
8. Solenoid Enclosure, Voltage
& Hertz
9. When Vertically Installed
Represented By:
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
CLA-VAL UK
134-60 (R-8/2014)
71
834-05
MODEL
Principle of Operation
Control Options
Electric Operation
Pneumatic Operation
Hydraulic Operation
Manual Operation
Outlet
Inlet
FLOW
Outlet
Inlet
FLOW
Model 834-05
Dimensions
"L"
T-2
T-1
T-1
"D"
T-3
4, 6, 8
Factory Mutual
Approved
(with approved
Pilot
Components)
T-3
T-2
6
10
4
8
17.25 18.25 20.00 22.00
9.5 11.75 14.00 16.00
1/2
1/2
1/2
1/2
2
2
2
2
151
196
330
285
100
438
241
1/2
2
68
150
464
299
1/2
2
89
250
559
406
1/2
2
150
200
508
356
1/2
2
129
FLOW FACTORS
SIZE (IN) CV (gpm)
340
4
885
6
1667
8
2424
*10
KV
77.3
201
379
550
*Calculated
MAIN VALVE
Ends:
Body:
Tube Diaphragm:
Barrier:
Bolts:
Pressure:
Temp. Range:
MAIN VALVE OPTIONS
Body:
PILOT VALVE
All Parts:
O-Rings:
Control Range:
Pilot Pressure Range:
Operation:
Item Description
1
2
3
4
5
6
Item Description
9
10
11
12
Pressure Switch
CGA Angle Valve
Automatic Drain Valve
Pressure Gauge
Bronze / Monel
Nitrile Rubber
20 to 250 PSIG
20 to 250 PSIG
Latches in operated position;
manual reset
Monel (Alloy 400)
Non-latching
Cla-Val 800 Series Control Valves operate with maximum efficiency when mounted in horizontal or vertical piping. We recommend isolation
valves be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be considered
essential. A regular maintenance program should be established based on the specific application data. However, we recommend a thorough
inspection be done at least once a year. Consult factory for specific recommendations.
CLA-VAL
E-834-05 (R-3/2011)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
73
834-60
MODEL
Principle of Operation
Control Options
Electric Operation
Pneumatic Operation
Hydraulic Operation
Manual Operation
Outlet
Inlet
FLOW
74
Outlet
Inlet
FLOW
Model 834-60
Dimensions
Valve Size (Inches)
L
D
T-1/T-2 (NPT)
T-3 (NPT)
Approx. Wt. (Lbs.)
"L"
T-2
T-1
T-1
"D"
6
10
4
8
17.25 18.25 20.00 22.00
9.5 11.75 14.00 16.00
1/2
1/2
1/2
1/2
2
2
2
2
151
196
330
285
100
438
241
1/2
2
68
150
464
299
1/2
2
89
200
508
356
1/2
2
129
250
559
406
1/2
2
150
FLOW FACTORS
T-3
T-2
KV
77.3
201
379
550
*Calculated
MAIN VALVE
Ends:
Body:
Tube Diaphragm:
Barrier:
Bolts:
Pressure:
Temp. Range:
MAIN VALVE OPTIONS
Body:
PILOT VALVE
All Parts:
O-Rings:
Control Range:
Pilot Pressure Range:
Operation:
PILOT VALVE OPTIONS
All Parts:
Operation:
Bronze / Monel
Nitrile Rubber
20 to 250 PSIG
20 to 250 PSIG
Latches in operated position;
manual reset
Monel (Alloy 400)
Non-latching
Cla-Val 800 Series Control Valves operate with maximum efficiency when mounted in horizontal or vertical piping. We recommend isolation valves
be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be considered essential.
A regular maintenance program should be established based on the specific application data. However, we recommend a thorough inspection be
done at least once a year. Consult factory for specific recommendations.
CLA-VAL
E-834-60 (R-3/2011)
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
75
Optional
Control Arrangements
803-35
76
834-60
814-01
834-61
834-05
834-62
Series 403
Pneumatically Operated Remote Control
Valve for Freshwater & Seawater Service
The Cla-Val 403 Series Remote Control Valve is used where on-off control is required. Pressure signals from a remote control open or close a
small auxiliary valve installed on the main valve cover, which in turn opens
or closes the main valve. Only the small amount of fluid in the auxiliary
valve cover must pass through the remote control pilot in order to fully
open or close the larger main valve.
403G-11A
Specifications
The Model 403 Series consists of a 100-01 Hytrol main valve and a small
Hytrol auxiliary valve. Both the main valve and the auxiliary valve are single-seated, diaphragm operated globe type valves. Line pressure applied
to the auxiliary valve cover closes the main valve drip tight.
For Seawater Service use 100S/2100S or 100GS/2100GS Main Valve
Schematic Diagram
Item
1
2
3
4
Description
100-01 Hytrol (Main Valve)
X47A Ejector
100-02 Powertrol
CK2 Ball Valve
Optional Features
Item
A
F
H
Description
X46A Flow Clean Strainer
Independent Operating Pressure
Drain to Atmosphere
77
112
7.25
8.50*
9.00*
5.62
5.50
3.25
4.00*
4.25*
1.12
2.50
3.06
1.88
4.00*
4.25*
8
1
4
3
8
3
2
212
3
4
6
8
10
12
14
16
9.38 11.00 12.50
9.38 11.00 12.00 15.00 20.00 25.38 29.75 34.00 39.00 41.38
10.00 11.62 13.25 15.62 21.00 26.38 31.12 35.50 40.50 43.50
6.62 8.00 9.12 11.50 15.75 20.00 23.62 28.00 32.75 35.50
6.50 7.56 8.19 10.62 13.38 16.00 17.12 20.88 24.19 25.00
5.00
4.75 5.50 6.00 7.50 10.00 12.75 14.88 17.00 19.50 20.81
5.00 5.88 6.38 7.88 10.50 13.25 15.56 17.75 20.25 21.62
1.50 1.69 2.56 3.19 4.31 5.31 9.25 10.75 12.62 15.50
3.00 3.50 3.75 4.50 5.50 6.75 8.00 9.50 10.50 11.75
3.25 3.75 4.13 5.00 6.25 7.50 8.75 10.25 11.50 12.75
3.25 4.00 4.50
3.25 4.00 4.00 5.00 6.00 8.00 8.62 13.75 14.88 15.69
3.50 4.31 4.38 5.31 6.50 8.50 9.31 14.50 15.62 16.50
3
1
3
3
1
8
2
4
4
2
1
1
1
1
1
1
1
1
3
3
2
2
2
4
4
114
112
1
1
2
3
1
1
3
3
8
2
2
4
4
1
1
1
1
1
4-28
4-28
8-24
8-24
8-24
2-20
8-24
8-24
24
61.50
63.24
53.16
43.93
17.75
19.25
1
112
4-16
36
Dimensions
76.00
78.00
66.00
61.50
B (Diameter)
J
100-01
Threaded
&
K
Flanged
24.56 H
28.00
Inlet
GG
2
GGG
2
Inlet
D
DD
2
A
DDD
AA
3
4-16
AAA
Stem Travel
Approx. Ship Wt. Lbs.
0.4
15
0.6
35
0.7
50
0.8
70
1.1
140
1.7
285
2.3
500
2.8
780
3.4
1165
4.0
1600
4.5
2265
6.75 10.12
6200 11470
40
184
216*
229*
143
140
104
83
102*
108*
29
64
78
48
102*
102*
50
238
238
254
168
165
127
121
121
127
38
76
83
83
83
89
65
279
279
295
203
192
140
140
149
43
89
95
102
102
110
80
318
305
337
232
208
165
159
152
162
65
95
105
114
102
111
100
381
397
292
270
223
191
200
81
114
127
127
135
150
508
533
400
340
281
254
267
110
140
159
152
165
1
1
1
200
645
670
508
406
324
337
135
171
191
203
216
1
1
1
250
756
790
600
435
378
395
235
203
222
219
236
1
114
1
300
864
902
711
530
432
451
273
241
260
349
368
1
112
1
350
991
1029
832
614
495
514
321
267
292
378
397
1
2
1
400
1051
1105
902
635
528
549
394
298
324
399
419
1
112
1
600
1562
1606
1350
1116
451
489
2
2
2
8-24
8
2
3
8
2
2
1
2
2
2
1
2
Valve Capacity
Valve Sizes (inches)
15
16
1 1/2"
125
280
4
4
3
4
18
23
2"
208
460
4
4
3
4
4-28
4-28
20
32
28
64
2 1/2"
300
650
8-24
8-24
43
129
3"
460
1000
8-24
58
227
4"
800
1800
71
354
86
528
6"
1800
4000
8-24
102
726
114
1027
171
2812
257
5200
8"
3100
7000
2-20
4-16
900
1930
1981
1676
1562
624
711
2
2
2
(MAX)
Outlet
F
FF
When Ordering,
Please Specify
1. Catalog No. 403 Series
2. Valve Size
3. Pattern - Globe or Angle
4. Pressure Class
5. Threaded, Flanged or Grooved
6. Trim Material
7. Adjustment Range
8. Desired Options
9. When Vertically Installed
4-16
10"
12"
14"
16"
24"
4900 7000
8500 11000 28000
11000 16000 19000 25000 63000
36"
Functional Data
Valve Size
CV
Factor
Inches
112
212
mm.
40
32
7.7
29
7
50
54
13
61
14.6
65
85
20.4
101
24.2
80
115
27.6
139
33.4
100
200
48
240
58
Globe
Pattern
Gal./Min. (gpm.)
Angle
Pattern
Gal./Min. (gpm.)
Litres/Sec. (l/s.)
Litres/Sec. (l/s.)
150
200
440
770
105.6 184.8
541
990
130
238
10
250
1245
299
1575
378
12
14
16
300
350
400
1725 2300 2940
414
552
706
2500* 3060* 4200*
600 734.4 1008
24
36
600
7655
1837
900
13320
3200
*Estimated
CLA-VAL
78
Temperature Range
Water: to 180F
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
78
414-01
MODEL
The Cla-Val 414-01 Remote Control Valve is used where on-off control
is required. Pressure signals from a remote control open or close a small
auxiliary valve installed on the main valve cover, which in turn opens or
closes the main valve. Once sensing pressure drops to "set" pressure the
snap action pilot opens to relieve main valve cover pressure to open deluge valve. Once open the pilot valve must be "manually reset" in order to
close the valve.
414-01
Specifications
Schematic Diagram
Item
1
2
3
4
5
Description
100G/2100G Hytrol (Main Valve)
X46A Flow Clean Strainer
CDHS-3C-A2-3 Differential Control
X58C Restriction Assembly
100-01 Auxiliary Hytrol
VENT TO ATMOSPHERE
OUTLET (Remote
Control Air Pressure)
INLET
2
1
79
79
Dimensions
INLET
OUTLET
OUTLET
(Angle) INLET
(Globe)
3
10
80
100
150
200
250
A 150 ANSI
12.00
15.00
20.00
25.38
29.75
A 150 ANSI
305
381
508
645
756
AA 300 ANSI
13.25
15.62
21.00
26.38
31.12
AA 300 ANSI
337
397
533
670
791
B Dia.
9.12
11.50
15.75
20.00
23.62
B Dia.
232
292
400
508
600
C Max.
8.19
10.62
13.38
16.00
17.12
C Max.
208
270
340
406
435
2.56
3.19
4.31
5.16
8.50
65
81
110
131
216
E 150 ANSI
7.00
8.50
10.00
12.69
14.88
E 150 ANSI
178
216
254
322
378
--
8.81
10.50
13.19
--
--
224
267
350
--
4.00
4.97
6.00
8.00
8.62
102
126
152
203
219
--
5.28
6.50
8.50
--
--
134
165
216
--
4.75
5.94
7.25
8.50
10.50
121
151
184
216
267
2.69
2.81
3.88
5.31
6.56
68
71
99
135
167
2.56
2.81
3.81
4.81
5.81
65
71
97
122
148
7.00
4.03
6.75
17.00
15.50
178
102
171
432
394
2.56
2.81
3.81
4.81
8.50
65
71
97
122
216
1.75
2.41
2.75
4.00
4.24
45
61
70
102
108
N NPT
1/2"-14
3/4"-14
3/4"-14
N NPT
1/2"-14
3/4"-14
3/4"-14
P NPT
1-1/4"-11 1/2
P NPT
1-1/4"-11 1/2
3.47
3.25
88
83
EE 300 ANSI
F 150 ANSI
FF 300 ANSI
R 150 ANSI
2.50
EE 300 ANSI
F 150 ANSI
FF 300 ANSI
2"-11 1/2"
4.19
7.12
R 150 ANSI
64
2"-11 1/2"
106
181
RR 300 ANSI
3.12
3.78
3.75
4.69
7.81
RR 300 ANSI
79
96
95
119
198
X Pilot System
15.00
17.00
29.00
31.00
33.00
X Pilot System
381
432
737
787
838
Y Pilot System
11.00
12.00
20.00
22.00
24.00
Y Pilot System
279
305
508
559
610
Z Pilot System
11.00
12.00
20.00
22.00
24.00
Z Pilot System
279
305
508
559
610
Valve Capacity
Valve Sizes (inches)
3"
460
1000
4"
800
1800
6"
1800
4000
8"
3100
7000
10"
4900
11000
Functional Data
Valve Size
CV
Factor
Inches
mm.
Globe
Pattern
Gal./Min. (gpm.)
Angle
Pattern
Gal./Min. (gpm.)
Litres/Sec. (l/s.)
Litres/Sec. (l/s.)
80
115
27.6
139
33.4
100
200
48
240
58
150
200
440
770
105.6 184.8
541
990
130
238
10
250
1245
299
1575
378
When Ordering,
Please Specify
1.
2.
3.
4.
5.
6.
7.
8.
9.
Temperature Range
Water: to 180F
CLA-VAL
E-414-01 (R-5/2011)
80
CLA-VAL EUROPE
Copyright CLA-VAL 2016 Printed in USA Specifications subject to change without notice.
Represented By:
CLA-VAL UK
80
Optional Pneumatic
Control Arrangements
403-01
403-26
TO REMOTE
CONTROL
B
IND. OPER.
PRESSURE
B
B
H
DRAIN TO
ATMOSPHERE
OUTLET
INLET
A
1
403-07
403-27
TO REMOTE
CONTROL
2
TO REMOTE CONTROL
3
Y
4
S
B
H
DRAIN TO
ATMOSPHERE
DRAIN TO
ATMOSPHERE
INDEPENDENT
OPERATING
PRESSURE
OUTLET
INLET
INLET
A
1
OUTLET
A
1
403-11
403-35
TO REMOTE CONTROL
B
F
H
DRAIN TO
ATMOSPHERE
INDEPENDENT
OPERATING
PRESSURE
INLET
OUTLET
A
1
403-20
6
PILOT SIGNAL
414-01
EXH
3
VENT TO ATMOSPHERE
SUPPLY
OUT
PILOT
SUPPLY SIGNAL
SUPPLY
EXH
VALVE
3
Y
INLET
OUTLET
OUTLET (Remote
Control Air Pressure)
INLET
2
1
A
1
81
81
MODEL
The Cla-Val Model 210-01/610-01 Altitude Valve controls the high water level
in reservoirs without the need for floats or other devices. It is a non-throttling
valve that remains fully open until the shut-off point is reached. This valve is
designed for one-way flow only.
This valve is hydraulically operated and pilot controlled. The pilot control operates on the differential in forces between a spring load and the water level in
the reservoir. The desired high water level is set by adjusting the spring force.
The pilot control measures the reservoir head through a customer supplied
sensing line* connected directly to the reservoir.
Schematic Diagram
Item
1
2
3
4
5
Description
Hytrol (Main Valve)
CDS6A Altitude Control
X101 Valve Position Indicator
Bell Reducer
CV Flow Control (Closing)
This valve can also be furnished with auxiliary controls to meet the need for
multiple functions, such as: pressure sustaining, pressure reduction, rate of
flow control, solenoid override, etc.
If the check feature option is added and a pressure reversal occurs, the downstream pressure is admitted into the main valve cover chamber and the valve
closes to prevent return flow.
Optional Features
Item
A
B
D
F
H
P
R
S
Y
Description
X46A Flow Clean Strainer
CK2 (Isolation Valve)
Check Valve with Isolation Valve
Independent Operating Pressure
Dry Drain
X141 Pressure Gauge
Reservoir Gauge with Tester
CV Flow Control (Opening)
X43 "Y" Strainer
Typical Applications
Used on reservoirs where the water is withdrawn
through a separate line or through a bypass equipped
with a check valve. The valve opens to refill the reservoir when the water lowers below the shut-off level. For
more information see data sheet E-CDS6.
*Note: The reservoir pressure sensing line should be
3
4" minimum I.D. installed with a 2 slope from
the valve to the reservoir to avoid air pockets.
Note: We recommend protecting tubing and valve
from freezing temperatures.
82
*3-10 UL listed
Main Valve available
upon request.
Grade
ASTM A536
Flanged
Material
300
Class
End
Details
Liquid Volume
Displaced from
Diaphragm Chamber
When Valve
Opens or Closes
400
400
400
285
400
400
400
Valve
Size
ASTM B62
225
400
400
400
.032 gal
2 1/2
.043 gal
.080 gal
.169 gal
.531 gal
1.26 gal
10
2.51 gal
12
4.00 gal
14
6.50 gal
16
9.57 gal
B16.24
Note:
Materials
Component
Body & Cover
Available Sizes
Disc Retainer &
Diaphragm Washer
2" - 36"
Cast Iron
Cast Steel
Bronze
2" - 16"
2" - 16"
Cast Steel
Bronze
Displacement
18
9.57 gal
20
12.00 gal
24
29.00 gal
36
42.00 gal
Bronze is Standard
Stainless Steel is Optional
Inlet
Outlet
G
GG
GGG
F
FF
D
DD
DDD
Inlet
A
AA
AAA
B (Diameter)
J
100-01
Grooved
X
CC
(MAX)
Buna-N Rubber
Inlet
Outlet
Stainless Steel
EE
GGGG
X
(MAX)
Cover Capacity
250
Bronze
K
C
Grooved Threaded
ANSI
150
300
Standards* Class Class
Threaded &
Flanged
Pressure Class
100-01
(In inches)
B (Diameter)
Dimensions
2 1/2
11.00
11.00
11.62
11.00
8.00
7.56
6.88
5.50
5.50
5.88
1.69
2.88
3.50
3.75
4.00
4.00
4.31
.50
.50
.50
0.7
50
14
10
10
3
12.50
12.00
13.25
12.50
9.12
8.19
7.25
6.25
6.00
6.38
6.00
2.06
3.12
3.75
4.13
4.50
4.00
4.38
4.25
.50
.50
.50
0.8
70
15
11
11
15.00
15.62
15.00
11.50
10.62
9.31
7.50
7.88
7.50
3.19
4.25
4.50
5.00
5.00
5.31
5.00
.75
.75
.75
1.1
140
17
12
12
DDDD
AAAA
6
20.00
21.00
20.00
15.75
13.38
12.12
10.00
10.50
4.31
6.00
5.50
6.25
6.00
6.50
.75
.75
.75
1.7
285
29
20
20
25.38
26.38
25.38
20.00
16.00
14.62
12.69
13.25
5.31
7.56
6.75
7.50
8.00
8.50
1
1
1
2.3
500
31
22
22
10
29.75
31.12
23.62
17.12
14.88
15.56
9.25
8.00
8.75
8.62
9.31
1
1
1
2.8
780
33
24
24
12
34.00
35.50
28.00
20.88
17.00
17.75
10.75
9.50
10.25
13.75
14.50
1
1.25
1
3.4
1165
36
26
26
14
39.00
40.50
32.75
24.19
19.50
20.25
12.62
10.50
11.50
14.88
15.62
1
1.5
1
4.0
1600
40
29
29
16
41.38
43.50
35.50
25.00
20.81
21.62
15.50
11.75
12.75
15.69
16.50
1
2
1
4.5
2265
40
30
30
18
46.00
47.64
41.50
39.06
12.95
15.00
15.00
1
1.5
1
5.1
2982
43
32
32
20
52.00
53.62
45.00
41.90
15.00
16.50
16.50
1
1.5
1
5.63
3900
47
34
34
24
61.50
63.24
53.16
43.93
30.75
31.62
17.75
19.25
19.25
22.06
22.90
1
1.5
1
6.75
6200
68
39
39
30
63.00
64.50
56.00
54.60
21.31
22.50
24.00
2
2
2
7.5
7703
79
40
42
36
76.00
76.00
66.00
61.50
24.56
25.60
25.60
2
2
2
8.5
11720
85
45
47
Note: The top two flange holes on valve size 36 are threaded to 1 1/2"-6 UNC.
83
(In inches)
Pressure Ratings
Pressure Class
Dimensions
Flanged
Material
ANSI
Standards*
B (Diameter)
150
Class
300
Class
ASTM A536
Ductile Iron
B16.42
250
400
ASTM A216-WCB
Cast Steel
B16.5
285
400
ASTM B62
Bronze
B16.24
225
400
Valve
Size
Displacement
.032 gal
4"
.080 gal
6"
.169 gal
8"
.531 gal
10"
1.26 gal
12"
2.51 gal
Note:
Materials
Component
Body & Cover
Available Sizes
Disc Retainer &
Diaphragm Washer
Cast Steel
2.51 gal
16"
4.00 gal
18"
4.00 gal
20"
9.57 gal
24"
9.57 gal
30"
29.00 gal
3" - 16"
Cast Iron
Cast Steel
Bronze
Bronze is Standard
Stainless Steel is Optional
X
C
(MAX)
Outlet
Inlet
F
FF
Inlet
14"
3" - 16"
A
AA
Bronze
3" - 48"
Flanged
Cover Capacity
Liquid Volume
Displaced from
Diaphragm Chamber
When Valve
Opens or Closes
100-20
D
DD
Buna-N Rubber
Diaphragm
E
EE
Stainless Steel
10
12
14
16
18
20
24
30
36
42
48
A 150 ANSI
10.25
13.88
17.75
21.38
26.00
30.00
34.25
35.00
42.12
48.00
48.00
63.25
65.00
76.00
94.50
AA 300 ANSI
11.00
14.50
18.62
22.38
27.38
31.50
35.75
36.62
43.63
49.62
49.75
63.75
67.00
76.00
94.50
B Dia.
6.62
9.12
11.50
15.75
20.00
23.62
27.47
28.00
35.44
35.44
35.44
53.19
56.00
66.00
66.00
C Max.
7.00
8.62
11.62
15.00
17.88
21.00
20.88
25.75
25.00
31.00
31.00
43.94
54.60
61.50
61.50
D 150 ANSI
6.94
8.88
10.69
CF*
CF*
CF*
CF*
CF*
CF*
CF*
DD 300 ANSI
7.25
9.38
11.19
CF*
CF*
CF*
CF*
CF*
CF*
CF*
E 150 ANSI
5.50
6.75
7.25
CF*
CF*
CF*
CF*
CF*
CF*
CF*
EE 300 ANSI
5.81
7.25
7.75
CF*
CF*
CF*
CF*
CF*
CF*
CF*
F 150 ANSI
3.75
4.50
5.50
6.75
8.00
9.50
11.00
11.75
15.88
14.56
17.00
19.88
25.50
28.00
31.50
FF 300 ANSI
4.12
5.00
6.25
7.50
8.75
10.25
11.50
12.75
15.88
16.06
19.00
22.00
27.50
28.00
31.50
.375
.50
.75
.75
.50
.50
.75
.75
1.25
1.25
.375
.50
.75
.75
Stem Travel
0.6
0.8
1.1
1.7
2.3
2.8
3.4
3.4
4.5
4.5
4.5
6.5
7.5
8.5
8.5
45
85
195
330
625
900
1250
1380
1500
2551
2733
6500
8545
X Pilot System
13
15
27
30
33
36
36
41
40
46
55
68
79
85
86
Y Pilot System
10
11
18
20
22
24
26
26
30
30
30
39
40
45
47
Z Pilot System
10
11
18
20
22
24
26
26
30
30
30
39
42
47
49
*Consult Factory
84
12450 13100
Note: The top two flange holes on valve sizes 36 thru 48 are threaded to 1 1/2"-6 UNC.
210-01
100-01 Pattern: Globe (G), Angle (A), End Connections: Threaded (T), Grooved (GR), Flanged (F) Indicate Available Sizes
Inches
212
10
12
14
16
18
20
24
30
36
mm
50
65
80
100
150
200
250
300
350
400
450
500
600
750
900
Pattern
G, A
G, A
G, A
G, A
G, A
G, A
G, A
G, A
G, A
G, A
G, A
End Detail
T, F,
Gr
T, F,
Gr*
T, F,
Gr
F,
Gr
F,
Gr*
F,
Gr*
Suggested
Flow
(gpm)
Maximum
210
300
460
800
1800
3100
4900
7000
8400
Maximum
Intermittent
260
370
580
990
2250
3900
6150
8720
Suggested
Flow
(Liters/Sec)
Maximum
13
19
29
50
113
195
309
442
530
694
883
1073
1577
2650
3150
Maximum
Intermittent
16
23
37
62
142
246
387
549
664
863
1104
1369
1972
3028
3940
Valve
Selection
Basic Valve
100-01
*Globe
610-01
Valve
Selection
Basic Valve
100-20
Suggested
Flow
(gpm)
Suggested
Flow
(Liters/Sec)
100-20 Pattern: Globe (G), Angle (A), End Connections: Flanged (F) Indicate Available Sizes
Inches
10
12
14
16
18
20
24
30
36
42
48
mm
80
100
150
200
250
300
350
400
450
500
600
750
900
1000
1200
Pattern
G, A
G, A
G, A
End Detail
Maximum
260
580
1025
2300
4100
6400
9230
9230
16500
16500
16500
28000
33500
33500
33500
Maximum
16
37
65
145
258
403
581
581
1040
1040
1040
1764
2115
2115
2115
100-20 Series is the reduced internal port size version of the 100-01 Series.
Adjustment Ranges
5 - 40 ft.
30 - 80 ft.
70 - 120 ft.
110 - 160 ft.
150 - 200 ft.
Temperature Range
Water: to 180F
If flowing line pressure is less than
10 psi, consult factory for full details.
If inlet pressure is above 150 psi, consult factory for recommendations.
CLA-VAL
Represented By:
E-210-01/610-01 (R-5/2015)
COPYRIGHT
CLA-VAL EUROPE
Chemin ds Mesanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax:
41-21-643-15-50
www.cla-val.com
85
Series
33A
Sizes 1" - 2" - 3" - 4" - 6"
High Performance Combination
Air Release & Vacuum Breaker Valve
Designed to protect pipelines and vertical turbine pump applications on offshore platforms from air lock and vacuum collapse, the Cla-Val Model 33A Combination Air Release and
Vacuum Breaker Valve eliminates air and prevents vacuum
formations in pipelines. A large venting orifice and large float
clearances freely exhaust or admits air during pipeline filling
or draining.
During normal pipeline operation, air accumulation and buoyancy cause the float ball to lower or lift. As the water level
lowers inside the valve, small amounts of accumulated air are
released through the small orifice. Once air is released, the
patented float poppet system closes drip tight.
Threaded
Flanged
Valve servicing is simple because the entire float poppet system, can be replaced without removal of the valve body from
the pipeline.
Typical Applications
Standard Max. D.W.P. 300 psi (For Higher
Operating Pressures Consult Factory)
Transmission Pipeline High Points
33A High Performance
Combination Air Release
& Vacuum Breaker Valve
with a Series TD Throttling
Air Control Device
Shut-Off Valve
Airline
Gauge
Series 33A Combination Air Release and Vacuum Breaker Valves are
typically installed at high points in pipelines for air release, or at anticipated
pipeline vacuum occurrence locations. Install Series 33A at regular intervals
(approximately 1/2 mile) along uniform grade line pipe. Mount the unit in the
vertical position on top of the pipeline, and include an isolation/shutoff valve.
Meter
Check Valve
Well Casing
Operation
Air Release ModeValve is normally open.
When line is filled or pump started, air is exhausted through the normally open
33A valve. As liquid fills the valve, float ball rises to form a drip-tight closure
and remaining air is exhausted through small orifice.
Vacuum Prevent Mode When line pressure drops below positive pressure
and the liquid level lowers, the float drops, unseating the valve and allowing
air into the line, thus preventing a vacuum.
Note: Available for Sea Water Service See Material Specifications
86
FLOW
Pump Column
Air Line
Blow-Off
Tee and
Valve
Main
Gate
Valve
Sample
Cock
1" NPT
2" NPT
3" NPT
4" NPT
1" NPT
2" NPT
3" NPT
4" NPT
25
29
38
40
Valve Size
A
B
E
Inlet (ANSI)
Outlet (NPT)
Number of Holes
Diameter of Bolts
Shipping Wt. (Lb.)
Pressure Ratings
OUTLET
Valve
Size
Orifice
Dia.
Standard
Maximum
Pressure
1"
.076"
300 psi
2"
.076"
500 psi
.125"
300 psi
.076"
300 psi
6"
.076"
300 psi
Materials of Construction
Ductile Iron ASTM A536 65-45-12
Epoxy Coated Cast Steel ASTM A 216WCB
ASTM B61 Naval Bronze
ASTM B 148 NI Aluminum Bronze
316 Stainless Steel
Duplex Stainless Steel
Threaded
INLET
OUTLET
Specifications
Standard Internals
Float: Stainless Steel 304SS Standard, T316 or Monel optional (extra cost)
Balance internals parts Stainless Steel and Delrin
When Ordering,
Seals Nitrile Rubber or Viton (extra cost)
Please Specify
1. Catalog No.
2. Valve Size
3. Pressure Rating
4. Materials
Temperature Range
Water to 180 F
Optional:
1. Fusion epoxy lined and coated
2. For Well Service Throttling Device on the Outlet Specify Model TD
1"
1
0
2"
10
14
3"
18
22
26
30
40
CLA-VAL
6"
4"
50
60
Pressure (psig)
PRESSURE IN P.SI.
Large Orifice
3
2
INLET
Flanged
500
475
450
425
400
375
350
325
300
275
250
225
200
175
150
125
100
75
50
10
0
.076"
10
15
.125"
20
25
30
35
40
45
50
1701 Placentia Avenue Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com Website cla-val.com
Copyright Cla-Val 2016 Printed in USA Specifications subject to change without notice.
87
Series 33B
Designed to protect pipelines from air lock and vacuum collapse, the
Cla-Val Model 33B Air Release and Vacuum Breaker Valve eliminates
air and prevents vacuum formations in pipelines. A large venting orifice and large float clearances freely exhaust or admits air during
pipeline filling or draining.
During normal pipeline operation, air accumulation and buoyancy
cause the float ball to lower or lift. As the water level lowers inside the
valve, small amounts of accumulated air are released through the
small orifice. Once air is released, the patented float poppet system
closes drip tight.
Flanged Inlet
Available
Valve servicing is simple because the entire float poppet system, can
be replaced without removal of the valve body from the pipeline.
Typical Applications
Water Transmission Pipeline High Points
Water Treatment Plant Piping High Points
Vertical Turbine Pump Discharge
Installation
Series 33B Air Release and Vacuum Breaker Valves are typically installed at high points in pipelines for air release, or at
anticipated pipeline vacuum occurrence locations. Install Series
33B at regular intervals (approximately 1/2 mile) along uniform
grade line pipe. Mount the unit in the vertical position on top of
the pipeline, and include an isolation/shutoff valve.
Shut-Off
Airline
Gauge
581
Meter
Check Valve
Operation
Air Release ModeValve is normally open.
When line is filled or pump started, air is exhausted through the
normally open 33B valve. With excessive air exhaust, the nonsurge orifice closes. Air will continue to be exhausted through the
non-surge orifice disc. The non-surge float prevents the slam effect
and therefore suppresses water hammer.
As liquid fills the valve, float ball rises to form a drip-tight closure
and remaining air is exhausted through small orifice.
Vacuum Prevent Mode When line pressure drops below positive pressure and the liquid level lowers, the float drops, unseating
the valve and allowing air into the line, thus preventing a vacuum.
88
Well Casing
FLOW
Pump Column
Air Line
Blow-Off
Tee and
Valve
Main
Gate
Valve
Sample
Cock
Specifications
MODEL 33B - 1, 2 SIZES
Single Body Combination Air Vacuum and Air Release Valve
Pressure Ratings
500 psi
600 psi
1"
2"
9.10
12.44
6.25
7.50
Materials
Body and Cover: Ductile Iron ASTM A536 65-45-12
500 psi
Valve Size
Inlet (NPT)
Outlet (NPT)
25
29
300
500
300
500
Standard Internals:
Bronzes ASTM B61 or ASTM B148
Monel / 316 Stainless Steel
Duplex Stainless Steel UNS S31803
Super Duplex Stainless Steel ASTM A890-5A UNS J93404
Super Austenitic Stainless Steel 6MO UNS S31254
Titanium ASTM B367 Gr 2
Standard Internals:
Float: Delrin
Seals Nitrile Rubber or Viton (extra cost)
When Ordering,
Please Specify
1. Catalog No.
2. Valve Size
3. Pressure Rating
4. Materials
Temperature Range
Water to 180 F
Optional:
1. For Well Service use 33C Type
Available Flanged
Determine anticipated water flow and allowable pressure differential for the pipeline application. Select valve from chart to
exhaust or admit air at the same rate as water filling or draining (in CFS). For larger flows, two or more Model 33B's may
be installed in parallel
10
8
dp Pressure (psig)
9
7
6
5
4
3
150
100
50
2
1
0
0
CLA-VAL
4
5
Air Flow Rate (scfm)
P.O. Box 1325 Newport Beach, CA 92659-0325 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: claval@cla-val.com Website cla-val.com
Copyright
E-33B (R-10/2010)
89
Series 501A
Wafer Swing Check Valve
Standard Style
2-12
DESCRIPTION
Cla-Val Series 501A Wafer Swing Check Valve has a quick,
spring-assisted closure that minimizes the possibility of
water hammer. The swing check design offers low head loss
and a full-flow passageway making it ideal for water or wastewater applications. The short lay length of the valve allows
for a space-saving design. It is available in sizes 2 to 30,
with either a 125 lb. or 150 lb. pressure class rating.
SPECIFICATIONS
The wafer swing check valve shall have torsional a
spring-assisted fast closure to minimize possibility of
water hammer. The valve shall be constructed of
either cast iron or steel body.
The body shall have a machined dovetail groove to
retain a field replaceable Nitrile (Buna-N) Seal that
provides water-tite shut-off at low/high pressure
The valve disc/arm assembly shall be one piece
design utilizing an integral disc arm for connection to
the shalt for positive shut-off and no disc flutter.
NORMAL FLOW
NORMAL FLOW
Note Hinge
Position
NORMAL FLOW
Note Hinge
Position
NORMAL FLOW
NORMAL FLOW
Note Hinge
Position
NORMAL
FLOW
90
4 18
1 1116
1 38
2 2
4 8
13
1 16
5 38
Wt.Lbs.
(Deg.)
16
59
3.1
1 4
1 16
60
2 8
4.2
2 12
2 38
1 18
62
6.6
6 4
2 2
3 8
1 8
60
8.1
7 34
2 34
3 78
2 12
61
12.3
8 34
4 12
3 34
72
18
11
3 2
6 4
4 4
70
7 4
27.3
10
13 38
4 12
7 58
5 34
66
9 34
51.3
12
16 18
4 12
9 12
7 38
65
11 34
72.6
No.
1
2
3
4
5
6
7
8
9
10
Description
Body
Disc
Shaft
Plug
Seat (Shaft)
Seat (Body)
Bushing
Travel Stop
Tag
Spring
13
Material
Cast Iron or Steel
316 Stainless Steel
316 Stainless Steel
304 Stainless Steel
PTFE
Nitrile or Viton
316 Stainless Steel
316 Stainless Steel
Aluminum
304 Stainless Steel
TM
EyeBolt
A
DIA. C
DIA.
10
3
8
11
9
5
7
4
1
B
FLOW
Technical Data
Pressure Rating:
Specifications
ASTM A48 / ASTM A216
ASTM A473 / A743M - CF8M
ASTM A276
ASTM A276
Commercial
ASTM A276
ASTM A276
-
Temperature Range:-
5 to 210 F
Water, Wastewater,
Chemicals and Petroleum
100
80
2 1/2"
3"
4"
5"
6"
6"
60
50
40
30
20
10
8
6
5
4
3
When Ordering,
Please Specify
1
0.8
0.6
0.5
0.4
0.3
2. Valve Size
3. Seat O-Ring Material
0.2
X 10
3 4 56 8 1
X 100
3 4 56
X 1,000
8 1
2 3 4 56 8 1
X 10,000
Valve
Size
Be Informed:
2
3 4
X 100,000
Inches
2
2 1/2
3
4
5
6
8
10
12
14
16
18
20
24
mm
50
65
80
100 125 150
200
250
300
350
400
450
500
610
Cv
Gal/Min
61
116 208 325 551 843 1640 2702 3996 5732 8548 11846 14327 22132
Factor Liters/Sec 3.85 7.32 13.12 20.5 34.76 53.18 103.47 170.47 252.11 361.63 539.29 747.36 903.89 1396.31
30
750
**
**
91
Series 580
Silent Wafer Check Valve
Product Advantages
Pressure Ratings
125/150 (Rated to 250 psi)
250/300 (Rated to 640 psi)
10
9
8
7
6
5
1 14"
1 12"
2"
2 12"
3"
4"
Materials
5" 6"
Valve Body:
Ductile Iron - ASTM 536 65-45-12
8"
4
3
1
.9
.8
.7
.6
.5
.4
Spring:
316 Stainless Steel; Stone
Tumbled and Stress Relieved - SS
ASTM A276 T16
.3
.2
.1
4 5 6 7 8 9 10
5 6 7 8 9 100
4 5 6 7 8 9 1,000
92
4 5 6 7 8 9 10,000
Note:
Standard offering is two-part epoxy
coating interior and exterior
125/150 & 250/300 Class Silent Wafer Check Valve: 1 thru 6-inches
B
A - Diameter
C - Diameter
Max Mating
Flange &
Gasket I.D.
Flow
Mating 2
Flange
Valve Size
(inches)
1
1.25
1.50
2
2.50
3
4
5
6
Bolt Circle
250/300 Class
Valve
2.75
3.13
3.63
4.25
5.00
5.75
7.00
8.38
9.75
2.06
2.06
2.38
2.63
2.88
3.13
4.00
4.63
5.50
1.25
1.50
1.81
2.38
2.88
3.38
4.75
5.50
6.50
0.06
0
0.09
0
0
0.06
0.06
0.50
0.88
Valve Size
(mm)
25
32
40
50
65
80
100
125
150
Bolt Circle
125/150 Class
69.9
79.4
92.1
108.0
127.0
146.1
177.8
212.7
247.7
52.4
52.4
60.3
66.7
73.0
79.4
101.6
117.5
139.7
31.8
38.1
46.0
60.3
73.0
85.7
120.7
139.7
165.1
1.6
0
2.4
0
0
1.6
1.6
12.7
22.2
Note: Dimensions are the same for both 125/150 and 250/300 Class Valves.
Specifications
The silent wafer check valve shall consist of a heavy ductile iron body, stainless steel seat, disc, and steel spring.The
valve disc shall be center guided at both ends with an integral shaft and shall be spring loaded for silent operation. The
spring shall be helical or conical and stone tumbled to achieve a micro-finish to resist mineral deposits. For ease of maintenance, the seat and disc shall be replaceable in the field.
Check valve shall be capable of silent operation when installed in vertical or horizontal positions with either flow up or flow
down. The flow area through the body shall be equal to or greater than the cross-section area of the equivalent pipe size.
93
A - Diameter
C - Diameter
Max Mating
Flange &
Gasket I.D.
Mating
Flange
Flow
Valve
C - Diameter
Max Mating
Flange &
Gasket I.D.
Flow
Mating Flange
Valve Size
(inches)
8
10
Valve
13.38
16.00
6.50
8.25
8.50
10.50
1.88
1.19
Valve Size
(mm)
200
250
Note: Dimensions are the same for both 125/150 and 250/300 Class Valves.
94
339.7
406.4
165.1
209.6
215.9
266.7
47.6
30.2
Threaded Seat
Connection
Detail A
(metal-to-metal seating surface shown)
For valves
3 - 10 inches
Item
Description
Qty
1
2
3
4
5
6
7
8
Body
Seat
Plug
Spring
Bushing
Seat Retaining Ball (3-10)
Seat Retaining Screw (3-10)
Optional Resilient Seat
1
1
1
1
1
2
2
1
Material
Description
Ductile Iron 536 65-45-12
SS ASTM A276 T304
SS ASTM A276 T304
SS ASTM A276 T316
SS ASTM A276 T304
SS ASTM A276 T304
SS ASTM A276 T304
Buna-N
Typical Applications
Cla-Val 580 Series Silent Wafer Check Valves are used anywhere a quick, quiet closure is desired and in the majority of
pump applications, including the following;
Fire Pump Applications
Vertical Turbine Pumps
Booster Pump Stations in High Rise Buildings
House Pump Applications
2
5
4
1
CLA-VAL
1701 Placentia Ave Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com www.cla-val.com
Cla-Val 2016 Printed in USA Specifications subject to change without notice.
E-580 (R-01/2016)
Copyright
95
Series 581
Silent Globe Check Valve
Product Advantages
The Cla-Val Series 581 Silent Globe Check Valve has a springloaded poppet that allows the valve to close at 1/4 psi before
flow reversal occurs, resulting in a silent, non-slam closure.
Constructed of a ductile iron body with stainless steel trim, the
Cla-Val Silent Globe Check Valve offers watertight shutoff with
metal-to-metal seating. Buna-N resilient seats are available
as an option for special applications,
Specifications
The silent globe check valve shall consist of an epoxy-coated
ductile iron body, stainless steel seat, disc and spring. The
valve disc shall be center guided at both ends with an
integral shaft and shall be spring loaded for silent operation.
The spring shall be helical or conical and stone tumbled to
achieve a micro-finish to resist mineral deposits. For ease of
maintenance, the seat and disc shall be replaceable in the
field.
Check valve shall be capable of silent operation when
installed in vertical or horizontal positions with either flow up
or flow down. The flow area through the body shall be equal
to or greater than the cross-section area of the equivalent pipe
size. Sizes 2 1/2 to 10 shall allow bolting a wafer style
butterfly valve directly to the outlet flange without a spool
piece.
Series 581P Pressure Loss Curve
6
5
4
3
2
1
96
10
11 12
Pressure Ratings
125/150 (Rated to 250 psi)
250/300 (Rated to 640 psi)
4 through 12-inches
Materials
(Typical)
Valve Body:
Ductile Iron - ASTM 536 65-45-12
Disc & Seat:
304 Stainless Steel - SS ASTM A276 T304
Spring:
316 Stainless Steel; Stone Tumbled and
Stress Relieved - SS ASTM A276 T16
Note:
Standard offering is two-part epoxy coating interior and
exterior
A diameter
H
D
J - Maximum Mating
Flange & Gasket I.D.
Valve Size
(inches)
3
4
5
6
8
10
12
14
16
18
20
24
30
36
42
Valve Size
(mm)
80
100
125
150
200
250
300
350
400
450
500
600
750
900
1000
E - Qty of Holes
F - Hole Diameter
G - Bolt Circle
Diameter
7.50
9.00
10.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
38.75
46.00
53.00
6.00
7.25
8.50
9.00
10.13
12.00
14.38
15.7
17.63
18.75
20.63
24.00
29.5
45.00
50.00
6.06
7.63
9.38
10.88
13.69
17.50
20.56
22.56
25.50
27.25
31.25
37.19
45.13
53.38
60.00
0.94
0.94
0.94
1.00
1.13
1.19
1.25
1.38
1.44
1.56
1.69
1.88
2.13
2.38
2.63
4
8
8
8
8
12
12
12
16
16
20
20
28
32
36
0.75
0.75
0.88
0.88
0.88
1.00
1.00
1.13
1.13
1.25
1.25
1.38
1.38
1.63
1.63
6.00
7.50
8.50
9.50
11.75
14.25
17.00
18.75
21.25
22.75
25.00
29.50
36.00
42.75
49.50
0
0
0
0
0
0.16
0.31
0
0.69
1.38
1.13
2.25
3.56
0
0
3.38
4.75
5.50
6.50
8.50
10.75
12.88
14.75
16.50
18.75
20.63
24.75
29.50
36.00
42.00
190.5
228.6
254.0
279.4
342.9
406.4
482.6
533.4
596.9
635.0
698.5
812.8
984.3
1168.4
1346.2
152.4
184.2
215.9
228.6
257.2
304.8
365.1
400.1
447.7
476.3
523.9
609.6
743.0
1143.0
1270.
154.0
193.7
238.1
276.2
347.7
444.5
522.3
573.1
647.7
692.2
793.8
944.6
1146.2
1355.7
1524.0
23.8
23.8
23.8
25.4
28.6
30.2
31.8
34.9
36.5
39.7
42.9
47.6
54.0
60.3
66.7
4
8
8
8
8
12
12
12
16
16
20
20
28
32
36
19.1
19.1
22.2
22.2
22.2
25.4
25.4
28.6
28.6
31.8
31.8
34.9
34.9
41.3
41.3
152.4
190.5
215.9
241.3
298.5
362.0
431.8
476.3
539.8
577.9
635.0
749.3
914.9
1085.9
1257.3
0
0
0
0
0
4.0
7.9
0
17.5
34.9
28.6
57.2
90.5
0
0
85.7
120.7
139.7
165.1
215.9
273.1
327.0
374.7
419.1
476.3
523.9
628.7
749.3
914.4
1066.8
97
A diameter
J - Maximum Mating
Flange & Gasket I.D.
Valve Size
(inches)
3
4
5
6
8
10
12
14
16
18
20
24
30
36
42
Valve Size
(mm)
80
100
125
150
200
250
300
350
400
450
500
600
750
900
1000
98
E - Qty of Holes
F - Hole Diamete
G - Bolt Circle
Diameter
8.25
10.00
11.00
12.50
15.00
17.50
20.50
23.00
25.50
2.00
30.50
36.00
43.00
50.00
57.00
6.00
7.25
8.50
9.00
10.13
12.00
14.38
15.75
17.63
18.75
20.63
24.00
29.25
45.00
50.00
6.06
7.63
9.38
10.88
13.69
17.50
20.56
22.56
25.50
27.25
31.25
37.19
45.13
53.38
60.00
1.13
1.25
1.38
1.44
1.63
1.88
2.00
2.13
2.25
2.38
2.50
2.75
3.00
3.38
3.69
8
8
8
12
12
16
16
20
20
24
24
24
28
32
36
0.88
0.88
0.88
1.00
1.00
1.13
1.25
1.25
1.38
1.38
1.38
1.63
1.88
2.25
2.25
6.63
8.25
9.25
10.56
13.00
15.25
17.75
20.25
22.50
24.75
27.00
32.00
39.25
46.00
52.75
0
0
0
0
0
0.16
0.31
0
0.69
1.38
1.13
2.25
3.56
0
0
3.38
4.75
5.50
6.50
8.50
10.75
12.88
14.75
16.50
18.75
20.63
24.75
29.50
36.00
42.00
209.6
254.0
254.0
317.5
381.0
444.5
520.7
584.2
647.7
711.2
774.7
914.4
1092.2
1270.0
1447.8
152.4
184.2
215.9
228.6
257.2
304.8
365.1
400.1
447.7
476.3
523.9
609.6
743.0
1143.0
1270.0
154.0
193.7
238.1
276.2
347.7
444.5
522.3
573.1
647.7
692.2
793.8
944.6
1146.2
1355.7
1524.0
28.6
31.8
34.9
36.5
41.3
47.6
50.8
54.0
57.2
60.3
63.5
69.9
76.2
85.7
93.7
8
8
8
12
12
16
16
20
20
24
24
24
28
32
36
0.88
22.2
22.2
22.2
25.4
28.6
31.8
31.8
34.9
34.9
34.9
41.3
47.6
57.2
57.2
6.63
200.0
235.0
268.1
330.2
387.4
450.9
514.4
571.5
628.7
685.8
812.8
997.0
1168.4
1339.9
0
0
0
0
0
4.0
7.9
0
17.5
34.9
28.6
57.2
90.5
0
0
3.38
120.7
139.7
165.1
215.9
273.1
327.0
374.7
419.1
476.3
523.9
628.7
749.3
914.4
1066.8
Item
Description
Qty
10
1
2
3
4
5
6
7
8
9
10
11
Body
Seat
Plug
Spring
Bushing
Seat Retaining Ball
Seat Retaining Screw
Optional Resilient Seat
Plug Ring (30- 42)
Gasket (30- 42)
Plug Ring Screw (30- 42)
1
1
1
1
1
2
2
1
1
1
1
11
30 through 42 plug detail
(metal-to-metal seating surface shown)
5
1
4
Material
Description
Ductile Iron 536 65-45-12
SS ASTM A276 T304
SS ASTM A276 T304
SS ASTM A276 T316
SS ASTM A276 T304
SS ASTM A276 T304
SS ASTM A276 T304
Buna-N
Buna-N
Buna-N
3
8
Typical Applications
Water Supply
For Initial Priming
Cla-Val Priming
Air Release Valve
50 Series
Centrifugal
Pump
Shut-Off
System
581
Check Valve
Blow-Off
Tee and
Valve
Main
Gate
Valve
FLOW
Cla-Val
Series 583
Wet
Well
Cla-Val 581 Series Silent Globe Check Valves are used anywhere a quick, quiet closure is desired and in
the majority of pump applications, including the following;
Fire Pump Applications
Vertical Turbine Pumps
Booster Pump Stations in High Rise Buildings
House Pump Applications
CLA-VAL
1701 Placentia Ave Costa Mesa CA 92627 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: info@cla-val.com www.cla-val.com
Cla-Val 2016 Printed in USA Specifications subject to change without notice.
E-581 (R-01/2016)
Copyright
99
Series 582SWS
SPECIFICATIONS
Seawater Service
Pressure Relief Valve
582SWS
Check Valve
Offshore Platform
100
33A
Air Valve
Typical Application
UL
B DIA.
US
10
582SWS
Plain Ends 14" thru 24"
MINIMUM
COMPANION
FLANGE
BORE
FLOW
Part No.
Name
1
Body
2
3
4
5
Door
Torsion Springs
Door Hinge Pin
Door Stop Pin
10
Material
Aluminum Bronze ASTM B148, Alloy 95200
with Buna-N resilient Seat Molded Body
Aluminum Bronze ASTM B148, Alloy 95200
Inconel X750, ASTM B637 Alloy N04400
Monel ASTM B164, Alloy N04400
Monel ASTM B164, Alloy N04400
MINIMUM
COMPANION
FLANGE
BORE
FLOW
Part No
6
7
8
9
10
Name
Door Thrust Bearing
Hinge Pin Retainer
Stop Pin Retainer
Stabilization Sphere
Spacer (2" - 12" Sizes)
Material
Monel ASTM B164, Alloy N04400
Monel 400
Monel 400
Buna-N
Monel ASTM B164, Alloy N04400
* FM Approved
CLA-VAL
Model
A
B
C
D
Wing Ends Two-Door Wafer Check Valve - ANSI Class 150
582SWS.4
2 5/8
6 7/8
1
4 5/8
582SWS.6
3 3/4
8 5/8
1 1/4
6 1/4
582SWS.8
5
12 1/4
1 5/8
8
582SWS.10
5 1/2
14 3/4
2 1/2
10 1/4
582SWS.12
7 1/8
17 3/8
1 15/16
12
Plain Ends Two-Door Wafer Check Valve for Seawater Service
582SWS.14
7 1/4
17 3/4
3 1/8
14 3/8
582SWS.16
7 1/2
20 1/4
4 1/2
16 3/8
582SWS.18
8
21 5/8
5 3/8
18 3/8
582SWS.20
8 3/8
23 7/8
6 3/8
20 1/4
582SWS.24
8 3/4
28 1/4
8 1/2
24 1/4
E
3
4
5
8
9
7/8
1/4
1/2
1/2
1/4
12 1/2
15
17
19
23
P.O. Box 1325 Newport Beach, CA 92659-0325 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: claval@cla-val.com Website cla-val.com
Copyright
E-582SWS (R-10/2011)
101
Series 582W
Series 582G
Two-Door Check Valve
Series
582W
2 1/2 - 16
65 - 400mm
UL
US 2 1/2 - 12
65 - 300mm
Series
582
SPECIFICATIONS
2 to 60
100,000
80,000
70,000
60,000
50,000
40,000
30,000
4"
5"
100
125 6"
8"
200 10"
250
150
7
6
5
12"
14"
300
350
16"
400
18"
450
20"
500
24"
42"
1100
30"
800
36"
900
600
Recommended Valve
Sizing Range
48"
1200
54"
1400
60"
1500
1
.8
.7
.6
.5
.4
1
.8
.7
.6
.5
2"
.4
2 1/2" 3"
4"
5"
.3
6"
8"
10"
.2
.2
.03
500,000
400,000
300,000
200,000
100,000
80,000
70,000
60,000
50,000
40,000
30,000
20,000
10,000
8,000
7,000
6,000
5,000
4,000
3,000
2,000
800
700
600
500
400
300
200
100
30 40
80
70
60
50
20
.3
.1
.08
.07
.06
.05
.04
12"
.1
10
102
20,000
8000
7000
6000
5000
2 1/2"
1,000
W
A
T
E
R
3000
316
8
7
6
5
4
3"
80
I
N
O
F
2000
2"
50
20
10
8
316
10
30
L
O
S
S
F
E
E
T
1000
40
60
Series
582
Pressure
Loss
Curve
800
700
600
500
400
200
100
30 40 50
80
70
60
H
E
A
D
20
10,000
Buna-N
316
Sealing Element:
Torsion Spring:
Stainless Steel
Hinge:
Stainless Steel
Stop:
Stainless Steel
Sizes:
M
E
T
E
R
S
O
F
W
A
T
E
R
UL
US
2 1/2 - 12
65 - 300 mm
Cla-Val Series
A
2 18
2 38
2 58
2 58
3 14
3 34
5
5 12
7 18
7 14
7 12
8
8 38
8 34
12
14 12
17
20 58
21 14
26
Cla-Val Series
A
54
60.3
66.7
66.7
82.6
95.3
127
139.7
181
184.1
190.5
203.2
212.7
222.2
304.8
368.3
431.8
523.9
539.8
660.4
CLA-VAL
INSTALLATION
Install the Cla-Val Series
582 Two-Door Wafer
Check Valve between
standard flanges in the
horizontal or in the
vertical, flow up, position.
Dimensions (mm)
Size
2
2 12
3
4
5
6
8
10
12
14
16
18
20
24
30
36
42
48*
54*
60*
Grooved
Wt Lbs.
4
5
8
9
13
18
30
56
81
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
Wafer
E
Wt Lbs.
49.2
1.8
58.7
2.3
73
3.2
98.4
4.1
122.2
5.9
146
8.6
193.7 17.2
242.9 29.5
288.9 42.6
317.5 84.8
381
122
431.8
150
482.6
192
584.2
268
723.9
504
876.3
846
1029 1310
1181
2506
1336 3175
1486 4580
Grooved
Wt Lbs.
1.8
2.3
3.6
4.1
5.9
8.2
13.6
25.4
36.7
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
N
A
NOTE:
For horizontal flow this
valve MUST Be installed
with disc hinge pin in the
VERTICAL position for
proper operation.
P.O. Box 1325 Newport Beach, CA 92659-0325 Phone: 949-722-4800 Fax: 949-548-5441 E-mail: claval@cla-val.com Website cla-val.com
Copyright
103
X46A Straight
X46B Angle
118
112
1 8
114
134
138
134
2 4
212
212
114
114
3 8
4 4
2 4
412
234
414
234
1
1
3
3
1
3
3
Male
Pipe
I
4
8
2
4
4
A
Female
Pipe
D
Straight Type A
8
8
8
8
SAE
Male
Pipe
138
134
178
2 8
3
1 4
Specifications
Body Brass (also available in stainless steel on special order)
Strainer Screen fabricated from Monel wire.
104
2
2
8
Angle Type B
ENGINEERING
DATA
Flow of Water Through Standard Wrought Iron or Steel Pipe
Based on Saph and Schoder Formula
Note: For old or rough pipes, add 25% to the pressure
drop given in the table. Velocities are shown in light
face type. Pressure drop shown in bold face type.
P=
3.68V1.86
P = Pressure drop, lbs. per sq. in. per 1000 ft. of pipe
V = Velocity, feet per second
d = Inside diameter of pipe, inches
d1.25
PRESSURE DROP POUNDS PER SQ. IN. PER 1000 FT. OF PIPE
(1.0 Lb. per Sq. In. = 2.30 Ft. of Water)
Discharge
Gallons Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure Vel. Ft. Pressure
Drop
Per
per
Drop
per
Drop
per
per
Drop
per
Drop
per
Drop
per
Drop
per
Drop
per
Drop
Mn.
Sec.
Sec.
Sec.
Sec.
Sec.
Sec.
Sec.
Sec.
Sec.
1
2
3
4
5
6
8
10
15
20
25
30
35
40
45
50
60
70
80
90
100
125
150
175
200
225
250
275
300
325
350
375
400
425
450
475
500
550
600
650
700
750
800
850
900
950
1,000
1,100
1,200
1,300
1,400
1,500
1,600
1,800
2,000
2,500
3,000
3,500
4,000
4,500
5,000
6,000
7,000
8,000
9,000
10,000
12,000
14,000
15,000
16,000
18,000
20,000
22,000
24,000
25,000
30,000
35,000
40,000
45,000
50,000
55,000
60,000
0.37
0.74
1.12
1.49
1.86
2.24
2.98
3.72
5.60
7.44
1"
0.55
2.00
4.25
7.30
11.10
15.40
25.30
40.00
85.00
145.00
1 1/4"
0.43
0.64
0.86
1.07
1.28
1.72
2.14
3.21
4.29
5.36
6.43
7.51
0.50
1.08
1.85
2.81
3.94
6.70
10.20
21.80
36.80
56.00
78.50
100.00
1 1/2"
0.47
0.63
0.79
0.95
1.26
1.57
2.36
3.15
3.94
4.72
5.51
6.30
7.08
7.87
0.50
0.86
1.31
1.82
3.11
4.70
10.10
17.10
26.00
36.40
48.30
62.50
78.00
94.00
6"
1.11
1.39
1.67
1.94
2.22
2.50
2.78
3.06
3.33
3.61
3.89
4.16
4.44
4.72
5.00
5.27
5.55
6.11
6.66
7.21
7.77
8.32
8.88
9.44
10.00
10.55
11.10
12.22
13.32
14.43
15.54
16.65
17.76
19.98
22.20
0.45
0.68
0.95
1.26
1.62
2.00
1.44
2.45
1.60
2.93
1.76
3.44
1.92
3.98
2.08
4.55
2.24
5.17
2.40
5.85
2.56
6.53
2.72
7.28
2.88
8.07
3.04
8.90
3.20
10.60
3.53
12.50
3.85
14.40
4.17
16.60
4.49
19.00
4.81
21.30
5.13
23.70
5.45
26.40
5.77
29.20
6.09
32.30
6.41
38.60
7.05
45.10
7.69
52.50
8.33
60.00
8.97
68.80
9.62
77.10 10.26
96.10 11.54
117.00 12.83
16.03
19.24
22.43
25.65
2"
0.57
0.76
0.96
1.43
1.91
2.39
2.87
3.35
3.82
4.30
4.78
5.74
6.69
7.65
8.60
9.56
2 1/2"
0.52
0.88
1.34
2.85
4.85
7.32
10.40
13.70
17.60
22.10
26.70
37.50
51.80
63.80
79.10
96.80
8"
0.51
0.63
0.74
0.87
1.02
1.12
1.32
1.49
1.67
1.85
2.05
2.28
2.71
3.18
3.67
4.23
4.80
5.41
6.05
6.72
7.45
8.18
9.82
11.60
13.40
15.40
17.50
19.70
24.50
29.90
45.10
63.20
84.00
108.00
0.67
1.00
1.34
1.68
2.01
2.35
2.68
3.00
3.35
4.02
4.69
5.37
6.04
6.71
8.38
10.06
11.73
0.55
1.18
2.00
3.04
4.26
5.14
7.29
9.12
11.00
15.50
21.40
26.40
32.80
40.00
60.60
87.10
115.90
3"
0.87
1.08
1.30
1.52
1.74
1.95
2.17
2.60
3.04
3.48
3.91
4.34
5.42
6.51
7.59
8.68
9.77
10.85
11.94
13.02
3 1/2"
0.68
1.02
1.44
1.92
2.45
3.08
3.72
5.20
7.25
8.90
11.10
13.50
20.50
28.80
39.00
49.00
60.60
74.10
88.20
104.00
10"
1.63
1.73
1.83
1.93
2.04
2.24
2.44
2.65
2.85
3.05
3.26
3.46
3.66
3.87
4.07
4.48
4.88
5.29
5.70
6.10
6.51
7.32
8.13
10.18
12.21
14.25
16.28
18.31
20.35
24.42
28.50
32.57
0.48
0.53
0.59
0.66
0.73
0.87
1.02
1.18
1.36
1.54
1.73
1.94
2.16
2.38
2.63
3.15
3.64
4.30
4.88
5.59
6.29
7.85
9.57
14.50
20.40
27.20
34.70
43.20
52.30
73.10
98.00
125.00
12"
1.84
1.99
2.13
2.27
2.41
2.55
2.69
2.84
3.12
3.41
3.69
3.97
4.26
4.54
5.11
5.67
7.09
8.51
9.93
11.35
12.76
14.18
17.02
19.85
22.70
25.53
28.37
34.00
0.48
0.55
0.63
0.70
0.79
0.87
0.96
1.06
1.27
1.50
1.74
1.99
2.28
2.56
3.19
3.86
5.88
8.23
10.90
14.10
17.40
21.30
29.80
39.60
50.90
62.80
77.00
108.00
0.81
0.97
1.14
1.30
1.46
1.62
1.95
2.27
2.59
2.92
3.24
4.05
4.86
5.67
6.48
7.29
8.10
8.91
9.72
10.53
11.35
12.17
12.97
13.78
14.59
15.40
0.49
0.69
0.93
1.18
1.49
1.80
2.54
3.48
4.33
5.31
7.78
9.90
13.90
18.40
23.60
29.30
35.80
42.60
50.20
58.00
66.80
75.20
85.30
95.30
108.00
118.00
4"
0.88
1.01
1.13
1.26
1.51
1.76
2.01
2.26
2.52
3.15
3.78
4.41
5.04
5.67
6.30
6.93
7.56
8.18
8.82
9.45
10.08
10.70
11.33
11.96
12.59
13.84
15.10
16.36
0.49
0.63
0.79
0.96
1.24
1.86
2.30
2.86
3.47
5.28
7.40
9.80
12.60
15.60
19.00
22.80
26.80
31.00
35.70
40.30
45.50
50.70
56.80
62.80
69.30
82.70
97.00
112.00
14"
1.98
2.10
2.21
2.33
2.56
2.80
3.03
3.26
3.49
3.73
4.19
4.66
5.82
6.98
8.16
9.32
10.48
11.63
13.97
16.30
18.62
20.95
23.30
27.95
32.60
34.95
37.25
0.48
0.53
0.59
0.65
0.78
0.91
1.06
1.22
1.39
1.56
1.93
2.37
3.58
5.02
6.68
8.52
10.60
12.90
18.20
23.20
30.90
38.30
46.70
66.00
87.50
99.40
112.00
16"
2.11
2.28
2.46
2.64
2.81
3.16
3.51
4.39
5.27
6.14
7.02
7.90
8.78
10.52
12.28
14.04
15.79
17.57
21.08
24.60
26.35
28.10
31.60
35.10
38.64
0.45
0.52
0.60
0.69
0.77
0.96
1.17
1.77
2.49
3.31
4.22
5.22
6.40
8.98
11.90
15.20
19.00
23.40
32.70
43.30
49.50
55.40
69.20
84.80
100.00
5"
1.12
1.28
1.44
1.60
2.00
2.41
2.81
3.21
3.61
4.01
4.41
4.81
5.21
5.61
6.01
6.41
6.82
7.22
7.62
8.02
8.82
9.62
10.42
11.22
12.02
12.82
13.62
14.42
15.22
16.02
17.63
19.24
0.57
0.70
0.87
1.06
1.62
2.28
3.00
3.85
4.76
5.85
6.92
8.20
9.55
10.90
12.40
14.00
15.60
17.40
19.20
21.30
25.40
29.80
34.50
39.70
45.00
50.80
56.70
62.80
69.60
76.80
91.80
108.00
18"
2.47
2.75
3.43
4.12
4.81
5.49
6.18
6.86
8.24
9.61
10.98
12.35
13.73
16.48
19.22
20.60
21.96
24.70
27.45
30.20
32.95
34.30
41.20
48.10
0.52
0.63
0.96
1.35
1.79
2.29
2.85
3.48
4.85
6.47
8.25
10.30
12.20
17.70
23.60
26.70
30.20
37.60
45.60
54.00
63.80
69.00
96.20
129.00
20"
3.30
3.85
4.41
4.96
5.51
6.61
7.71
8.82
9.92
11.02
13.22
15.42
16.52
17.62
19.83
22.03
24.23
26.43
27.54
33.04
38.55
44.10
49.60
0.55
0.78
1.04
1.32
1.64
2.00
3.74
4.76
5.90
7.22
10.20
13.50
15.30
17.40
21.60
26.40
31.20
36.80
39.60
55.50
74.20
95.30
119.00
24"
3.02
3.40
3.78
4.54
5.29
6.05
6.81
7.56
9.07
10.59
11.34
12.10
13.60
15.12
16.63
18.15
18.90
22.68
26.45
30.25
34.00
37.80
41.60
45.36
0.51
0.64
0.79
1.09
1.45
1.86
2.20
2.92
3.96
4.51
5.99
6.76
8.45
10.30
12.20
14.30
15.40
21.60
28.80
37.00
45.90
56.00
66.80
78.20
Ductile Iron Valves* Class 150 and 300 (ANSI B16.42 1987)
Nominal
Pipe Size
Diameter of
Flange
Thickness
of Flange
Diameter of
Raised Face
Diameter of
Bolt Circle
Number
of Bolts
Diameter
of Bolts
Diameter of
Bolt Holes
Pressure Class
150
300
150
300
150
300
150
300
150
300
150
300
150
300
1.5
2
2.5
3
4
6
8
10
12
14
16
18
20
24
30
36
5.00
6.00
7.00
7.50
9.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
38.75
46.00
6.12
6.50
7.50
8.25
10.00
12.50
15.00
17.50
20.50
23.00
25.50
28.00
30.50
36.00
43.00
50.00
.56
.62
.69
.75
.94
1.00
1.12
1.19
1.25
1.38
1.44
1.56
1.69
1.88
2.12
2.38
.81
.88
1.00
1.12
1.25
1.44
1.62
1.88
2.00
2.12
2.25
2.38
2.50
2.75
3.00
3.38
2.88
3.62
4.12
5.00
6.19
8.50
10.62
12.75
15.00
16.25
18.50
21.00
23.00
27.25
2.88
3.62
4.12
5.00
6.19
8.50
10.62
12.75
15.00
16.25
18.50
23.00
23.00
27.25
37.19
42.69
3.88
4.75
5.50
6.00
7.50
9.50
11.75
14.25
17.00
18.75
21.25
22.75
25.00
29.50
36.00
42.75
4.50
5.00
5.88
6.62
7.88
10.62
13.00
15.25
17.75
20.25
22.50
24.75
27.00
32.00
39.25
46.00
4
4
4
4
8
8
8
12
12
12
16
16
20
20
28
32
4
8
8
8
8
12
12
16
16
20
20
24
24
24
28
32
.50
.63
.63
.63
.63
.75
.75
.88
.88
1.00
1.00
1.12
1.13
1.25
1.25
1.50
.75
.63
.75
.75
.75
.75
.88
1.00
1.12
1.12
1.25
1.25
1.25
1.50
1.75
2.00
.62
.75
.75
.75
.75
.88
.88
1.00
1.00
1.12
1.12
1.25
1.25
1.38
1.38
1.62
.88
.75
.88
.88
.88
.88
.1.00
1.12
1.25
1.25
1.38
1.38
1.38
1.62
2.00
2.25
Cast Iron Valves* Class 125 and 250 (ANSI B16.1 1989)
Nominal
Pipe Size
Pressure Class
1.5
2
2.5
3
4
6
8
10
12
14
16
18
20
24
Diameter of
Flange
125
5.00
6.00
7.00
7.50
9.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
250
6.12
6.50
7.50
8.25
10.00
12.50
15.00
17.50
20.50
23.00
25.50
28.00
30.50
36.00
Thickness
of Flange
125
.56
.62
.69
.75
.94
1.00
1.12
1.19
1.25
1.38
1.44
1.56
1.69
1.88
250
.81
.88
1.00
1.12
1.25
1.44
1.62
1.88
2.00
2.12
2.25
2.38
2.50
2.75
Diameter of
Raised Face
125
21.00
250
2.88
3.62
4.12
5.00
6.19
8.50
10.62
12.75
15.00
16.25
18.50
23.00
23.00
27.25
Diameter of
Bolt Circle
125
3.88
4.75
5.50
6.00
7.50
9.50
11.75
14.25
17.00
18.75
21.25
22.75
25.00
29.50
250
4.50
5.00
5.88
6.62
7.88
10.62
13.00
15.25
17.75
20.25
22.50
24.75
27.00
32.00
Number
of Bolts
125
4
4
4
4
8
8
8
12
12
12
16
16
20
20
250
4
8
8
8
8
12
12
16
16
20
20
24
24
24
Diameter
of Bolts
125
.50
.63
.63
.63
.63
.75
.75
.88
.88
1.00
1.00
1.12
1.13
1.25
250
.75
.63
.75
.75
.75
.75
.88
1.00
1.12
1.12
1.25
1.25
1.25
1.50
Diameter of
Bolt Holes
125
.62
.75
.75
.75
.75
.88
.88
1.00
1.00
1.12
1.12
1.25
1.25
1.38
250
.88
.75
.88
.88
.88
.88
.1.00
1.12
1.25
1.25
1.38
1.38
1.38
1.62
Diameter of
Flange
150
5.00
6.00
7.00
7.50
9.00
11.00
13.50
16.00
19.00
300
6.12
6.50
7.50
8.25
10.00
12.50
15.00
Thickness
of Flange
150
.44
.50
.56
.62
.69
.81
.94
1.00
1.06
300
.69
.75
.81
.91
1.06
1.19
1.38
Diameter of
Raised Face
150
300
Diameter of
Bolt Circle
150
3.88
4.75
5.50
6.00
7.50
9.50
11.75
14.25
17.00
300
4.50
5.00
5.88
6.62
7.88
10.62
13.00
Number
of Bolts
150
4
4
4
4
8
8
8
12
12
300
4
8
8
8
8
12
12
Diameter
of Bolts
150
.50
.63
.63
.63
.63
.75
.75
.88
.88
300
.75
.63
.75
.75
.75
.75
.88
Diameter of
Bolt Holes
150
.62
.75
.75
.75
.75
.88
.88
1.00
1.00
300
.88
.75
.88
.88
.88
.88
.1.00
Cast Steel Valves* Class 150 and 300 (ANSI 16.5 1988)
Nominal
Pipe Size
Pressure Class
1.5
2
2.5
3
4
6
8
10
12
14
16
18
20
24
E-ED (R-10/09)
106
Diameter of
Flange
150
5.00
6.00
7.00
7.50
9.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
300
6.12
6.50
7.50
8.25
10.00
12.50
15.00
17.50
20.50
23.00
25.50
28.00
30.50
36.00
Thickness
of Flange
150
.56
.62
.69
.75
.94
1.00
1.12
1.19
1.25
1.38
1.44
1.56
1.69
1.88
300
.81
.88
1.00
1.12
1.25
1.44
1.62
1.88
2.00
2.12
2.25
2.38
2.50
2.75
Diameter of
Raised Face
150
2.88
3.63
4.13
5.00
6.19
8.50
10.63
12.75
15.00
16.25
18.50
21.00
23.00
27.25
300
2.88
3.63
4.13
5.00
6.19
8.50
10.63
12.75
15.00
16.25
18.50
23.00
23.00
27.25
Diameter of
Bolt Circle
150
3.88
4.75
5.50
6.00
7.50
9.50
11.75
14.25
17.00
18.75
21.25
22.75
25.00
29.50
300
4.50
5.00
5.88
6.62
7.88
10.62
13.00
15.25
17.75
20.25
22.50
24.75
27.00
32.00
Number
of Bolts
150
4
4
4
4
8
8
8
12
12
12
16
16
20
20
300
4
8
8
8
8
12
12
16
16
20
20
24
24
24
Diameter
of Bolts
150
.50
.63
.63
.63
.63
.75
.75
.88
.88
1.00
1.00
1.12
1.13
1.25
300
.75
.63
.75
.75
.75
.75
.88
1.00
1.12
1.12
1.25
1.25
1.25
1.50
Diameter of
Bolt Holes
150
.62
.75
.75
.75
.75
.88
.88
1.00
1.00
1.12
1.12
1.25
1.25
1.38
300
.88
.75
.88
.88
.88
.88
.1.00
1.12
1.25
1.25
1.38
1.38
1.38
1.62
107
P O Box 1325
Newport Beach CA
92659-0325
Phone: 949-722-4800
Fax: 949-548-5441
E-mail: claval@cla-val.com
CLA-VAL
CLA-VAL CANADA
CLA-VAL EUROPE
CLA-VAL FRANCE
CLA-VAL UK
The liability of Cla-Val is limited to material replacements F.O.B. Newport Beach, California.
No representative of Cla-Val may change any of the foregoing or assume any additional liability or responsibility in connection with the product.
Cla-Val shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product. Cla-Val shall not
be liable for any damages or charges for labor or expense in making repairs or adjustments to the product. Cla-Val shall not be liable for any damages or charges
sustained in the adaptation or use of its engineering data and services.
The foregoing warranty is exclusive and in lieu of all other warranties and representations whether expressed, implied, oral or written, including but not limited to,
any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled.
This warranty shall not apply if the product has been altered or repaired by others, and Cal-Val shall
make no allowance or credit for such repairs or alterations unless authorized in writing by Cla-Val.
Components used by Cla-Val, but manufactured by others, are warranted only to the extent of that
manufacturers guarantee.
We will repair or replace defective material, free of charge which is returned to our factory, transportation charges prepaid, provided that after inspection the material is found to have been defective
at time of shipment. The warranty is expressly conditioned on the purchasers giving Cla-Val immediate written notice upon discovery of the defect.
Automatic valves and controls as manufactured by Cla-Val are warranted for three years from date
of shipment against manufacturing defects in material and workmanship that develop in the service
for which they are designed, provided the products are installed and used in accordance with all
applicable instructions and limitations issued by Cal-Val. Electronic components manufactured by
Cla-Val are warranted for one year from the date of shipment.
CLA-VALWARRANTY
108
P O Box 1325
Newport Beach CA
92659-0325
Phone: 949-722-4800
Fax: 949-548-5441
E-mail: claval@cla-val.com
CLA-VAL
CLA-VAL CANADA
CLA-VAL EUROPE
CLA-VAL FRANCE
CLA-VAL UK
The liability of Cla-Val is limited to material replacements F.O.B. Newport Beach, California.
No representative of Cla-Val may change any of the foregoing or assume any additional liability or responsibility in connection with the product.
Cla-Val shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product. Cla-Val shall not
be liable for any damages or charges for labor or expense in making repairs or adjustments to the product. Cla-Val shall not be liable for any damages or charges
sustained in the adaptation or use of its engineering data and services.
The foregoing warranty is exclusive and in lieu of all other warranties and representations whether expressed, implied, oral or written, including but not limited to,
any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled.
This warranty shall not apply if the product has been altered or repaired by others, and Cla-Val shall
make no allowance or credit for such repairs or alterations unless authorized in writing by Cla-Val.
Components used by Cla-Val, but manufactured by others, are warranted only to the extent of that
manufacturers guarantee.
We will repair or replace defective material, free of charge which is returned to our factory, transportation charges prepaid, provided that after inspection the material is found to have been defective at time
of shipment. The warranty is expressly conditioned on the purchasers giving Cla-Val immediate
written notice upon discovery of the defect.
Roll Seal automatic valves and controls as manufactured by Cla-Val are warranted for one year from
date of shipment against manufacturing defects in material and workmanship that develop in the service for which they are designed, provided the products are installed and used in accordance with all
applicable instructions and limitations issued by Cal-Val. Electronic components manufactured by ClaVal are warranted for one year from the date of shipment.
CLA-VALWARRANTY
(949) 722-4800
(800) 942-6326
(949) 548-5441
info@cla-val.com
Cla-Val Canada
4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone:
Fax:
E-mail:
(905) 563-4963
(905) 563-4040
sales@cla-val.ca
Cla-Val Europe
US Regional Offices
E-mail:
info@cla-val.com
Central Region
8707 Forney Road
Dallas, TX 75227
Phone:
Fax:
(214) 388-3493
(800) 533-8181
(214) 381-9579
Eastern Region
6911 Richmond Highway, Suite 444
Alexandria, VA 22306
Phone:
(703) 721-1923
(800) 451-3030
(703) 721-1927
Chemin ds Mesanges 1
CH-1032 Romanel/Lausanne
Switzerland
Fax:
Phone:
Fax:
E-mail:
41-21-643-15-55
41-21-643-15-50
cla-val@cla-val.ch
Cla-Val UK
Western Region
Phone:
Fax:
(951) 687-9145
(800) 247-9090
(951) 687-9954
44-1892-514-400
44-1892-543-423
info@cla-val.co.uk
Cla-Val France
Porte du Grand Lyon 1
ZI de Champ du Prie
France - 01700 Neyo
Phone:
Fax:
E-mail:
33-4-72-25-92-93
33-4-72-25-04-17
cla-val@cla-val.fr
(64) 39644860
info@cla-valpacific.com
FPCatalog (R-09/2016)