Академический Документы
Профессиональный Документы
Культура Документы
Logging enable
logging standby
logging timestamp
logging trap <sevarity-level>
logging history <severity-level>
logging buffered <sevarity-level>
logging persistent <sevarity-level>
logging monitor <sevarity-level>
logging facility <number>
logging queue <queue-size>
logging device-id ipaddress vlan46
logging host <ip-address> <tcp|udp /port#>
logging rate-limit
resource-class <class-name>
limit-resource
boot system image:<filename>
login timeout <minutes>
peer hostname <name>
hostname <name>
interface gigabitEthernet <slot/number>
description <name>
Speed <speed>
duplex <full|half>
channel group <group-number>
shutdown - no shutdown
nat-pool <#> <ip start> <ip finsh> netmask <mask> pat
ntp server <ip-address>
access-list <name> line <#> extended <permit|deny> <operation>
fail-on-all
inservice
rate-limit {connection number1 | bandwidth number2}
weight <number>
fail-on-all
inband-health check <count | <log fail_threshold_count [reset milliseconds]> | <remove
fail_threshold_count [reset milliseconds] [resume-service seconds]>>>
partial-threshold <percentage1> back-inservice <percentage2>
description
match cipher {equal-to <cipher> | less-than <cipher_strength>}
match <name> http content <expression> {[offset <bytes>] [insert-before <map_name>]}
match <name> http cookie {<name2> | secondary <name3>} cookie-value <expression> [insertbefore <map_name>]
match <name> http header {<header_name> | <header_field>} header-value <expression> [insertbefore <map_name>]
exceed-mss <allow|drop>
description
nagle
random-sequence number
rate-limit <connection <number1 per sec>| bandwidth <number2>>
reserved-bits {allow | clear | drop}
set ip tos <number>
set tcp ack-delay <number>
set tcp buffer share <number>
set tcp mss {min <number1> max <number2>}
set tcp reassembly-timeout <seconds>
set tcp syn-retry < number>
A10 Command
(**from class-map)
healthcheck <name>
enable
conn-limit <max-conns>
enable
conn-rate-limit <number per sec> (in slb template port)
weight <number>
stateless-src-dst-ip-hash
stateless-src-ip-hash
stateless-dst-ip-hash
src-ip-only-hash
src-ip-hash
dst-ip-only-hash
dst-ip-hash
no-dest-nat
description
aflex
aflex
aflex
(host-switching contains <header_name> service-group <sg-name>)
or
(url-hash-persist first <number if bytes>)
or
(url-switching contains <url_name> service-group <sgname>)
(url-hash-persist first <number if bytes>)
enable-management service <type | acl> <acl#>
backend-wscale <number>
slow-start (server port template)
compression enable
compression content-type <type> (for mimetype)
compression minimujm-content-length <length> (for minimum-size)
redirectre-write match <url-string> rewrite-to <url-string>
request-header-erase <field>
request-header-insert <field:value> <insert-always | insert-if-not-exist>
expire <expire-seconds>
ca-cert <certname>
ca-cert <certname>
chain-cert <chain-cert-name>
cipher <type>
cipher <type>
Comment
No AX command
No AX command
(sevarity-level) 1 to 7, ACE levels match A10
No AX command
(sevarity-level) 1 to 7, ACE levels match A10
No AX command
(sevarity-level) 1 to 7, ACE levels match A10
(16-local0),(17-local1),(18-local2),(19-local3),(20-local4),(21-local5),(22-local6),(23-local7)
No AX command
can only configure once with all IP addresses in list format.
No AX command
No AX command, similar functionality to L3V template resource allocation v2.7.0
No AX command, similar functionality to L3V template resource allocation v2.7.0
No AX command
no AX command
4 max
conn-rate-limit <number per sec> (in slb template port) or (in slb template server)
no ax command
see host-switching in http template
(host-switching contains <header_name> service-group <sg-name>)
no ax command
see 'url-switching' in slb template HTTP
(url-switching contains <url_name> service-group <sgname>)
no ax command
no ax command
force RST to server instead of FIN for completed healthchecks.
no ax command
Similar to enable management service on AX.
same as above.
no ax command
No AX command, this command links the advanced loadbalancing options in the loadbalance policy
map.
in slb virtual port configuration.
No AX command
No AX command
in slb virtual port configuration.
NOTE (commands for AX in slb template http <name>)
%is(source IP), %id(destination IP), %ps(Source port), %pd(destination port)
in slb virtual port configuration.
no ax command, may need aflex.
no ax command, may need aflex.
no ax command, may need aflex.
no ax command
NOTE (commands for AX in slb template connection-reuse <conreuse>)
no ax command, use aflex
no ax command
possible aflex
possible aflex
no ax command
call to command cipher <type> for slb template client-ssl and server-ssl
no ax command
all additional chained certs are to be loaded to main cert.
no ax command, generate each set of params manually for each key/cert creation.
no ax command
to be applied to command cipher <type> for slb template client-ssl and server-ssl
no ax command