Академический Документы
Профессиональный Документы
Культура Документы
SERVICE MANUAL
Goldfish 4
GAUGE LINE-UP
ROUND STYLE GAUGES
2 kinds of round gauges are available.
The round gauges feature the similar shape design as conventional digital gauges (6Y5 type), and
reasonable cost.
COMB. SPEEDOMETER
AND FUEL MGT GAUGE
TACHOMETER
Part No.
Part No.
6Y8-8350T-11
1-5
6Y8-83500-11
GAUGE FEATURES
ROUND TACHOMETER
Maintenance information
Informs maintenance every
100-hour
Dimmer Function
Adjusts illumination in 5-stage with
independent or synchronization with
all gauges
Customization function
Selects measurement unit
Resets maintenance period
Selects motor for multiapplications
Adjusts zero trim angle
Warning information
Informs warning item with icon
Multi-gauge display
Shows Elapsed hour,
Trip hour,
Coolant temp.,
Coolant press.,
Oil pressure/level,
Engine voltage (ECU)
Selects gauge display
Engine information
Shows engine condition
by icon and letters, or graph
Customization function
Arranges each display
Selects measurement unit
Selects fuel sender
resistance
Dimmer Function
Adjusts illumination in
5-stage with independent
or synchronization with
all gauges
Speed display
Selects ground speed or
water speed
Multi-gauge display
Shows Total Fuel
consumption,
Fuel economy, and Fuel flow
Shows Water surface temp.,
Water depth, Trip distance,
and Clock
Selects gauge display
Warning information
Informs fuel warning
1-8
Comb.
Tachometer Speedometer &
Fuel MGT gauge
Descriptions
Shows 6-level
With low battery warning
1 (ECU)
Coolant pressure
(OP)
Coolant temperature
Diagnosis code
Dimmer illumination
Boat speed
Clock (OP)
1
1
Elapsed hour
Engine failure
warning
Engine RPM
Engine selection
Fuel consumption
Fuel economy
Fuel flow
Fuel level
Maintenance
indication
Oil level
(For 2-stroke engine)
Oil pressure
(For 4-stroke engine)
Shows 8-level
Trim position
Shows 13-level
Adjustable zero trim angle
Trip distance
Tripped hour
Troll RPM control
(For F50-F100)
Resettable (0-999.9h)
1
1
Feet or meter
Required optional multi-sensor
Activated if water has mixed into fuel
Celsius or Fahrenheit
Required optional multi-sensor
1-11
Engine RPM
Trim gauge
(High)
(Low)
(hour)
(Volt)
Multi-display
Elapsed hour
Trip hour
Coolant press. (OP)
Oil level or pressure
Coolant temp.
Engine voltage (ECU)
Troll RPM
Speed
Speed measurement
(Selectable)
Fuel gauge
Gauge
indicator
Multi-display
Trip distance
Fuel consumption
Fuel economy
Water surface temp. (OP)
Water depth (OP)
Clock (OP)
1-12
GAUGE DIMENSIONS
ROUND STYLE GAUGES
..
TACHOMETER
COMB. SPEEDOMETER AND FUEL MGT GAUGE
The round style gauges allow the surface mount only.
mm (in.)
(3
.3
7)
20 (0.79)
85
.5
.74)
95 (3
t = 1.5 (0.06)
1-14
Length
(GRY)
mm (in.)
B
B
(RED)
Part No.
Remarks
6Y8-83553-01
Part No.
30 ft
9.1 m
6Y8-82553-31
25 ft
7.6 m
6Y8-82553-21
20 ft
6.1 m
6Y8-82553-11
15 ft
4.6 m
6Y8-82553-50
10 ft
3.0 m
6Y8-82553-01
1 ft
0.3 m
mm (in.)
B
P/B
GPS
R
Length
(WHT)
Fuel
tank
220 (8.66)
300 (11.8)
3.6 m
6Y8-82521-41
9 ft
2.7 m
6Y8-82521-31
6 ft
1.8 m
6Y8-82521-21
3 ft
0.9 m
6Y8-82521-11
2 ft
0.6 m
6Y8-82521-01
1 ft
0.3 m
B
W
(BLK)
P/B
B
P
B
(WHT)
6Y8-82521-51
W (+)
L (GND)
Part No.
Part No.
6Y8-82553-41
70 (2.75)
170 (6.63)
2400 (94)
(GRY)
(10A)
6Y8-8356N-01
Remarks
Accommodated to twin fuel
tank and GPS
1-15
Ref.
Part No.
Descriptions
6Y8-81920-01
6Y8-82582-01
6Y8-82582-11
The 4-pin white cap (1) attached to the connector of engine wire-harness can be used as the
waterproof cap for the pigtail bus wire of multihub.
(1)
1
mm (in.)
SINGLE HUB
The white single hub is especially used for
single outboard motor installed without optional transom multi-sensor on the transom
area.
This hub is an adapter to change to the main
bus wire from the pigtail bus wire from the engine.
21.4
(0.84)
194.8 (7.67)
178 (7.01)
7 (0.28)
mm (in.)
22.55
(0.88)
41.4
(1.63)
10
(0.39)
18.54 (0.73)
26 (1.02)
19.65
(0.77)
42 (1.65)
19.3 (0.76)
(WHT)
Part No.
6Y8-81920-11
(RED)
23.95 (0.94)
20.25 (0.79)
26 (1.02)
(WHT)
1-16
Descriptions
Adapter 4-pin to 6-pin,
with ending resistor
SWITCH PANEL
SPECIFICATIONS
TWIN-SWITCH PANEL
mm (in.)
110 (4.33)
68 (2.68)
mm (in.)
66 (2.60)
154 (6.06)
110 (4.33)
B
Y
3.3 (0.13)
93 (3.66)
R
Y
G
B
Br
X
R
Br
L
3.3 (0.13)
*110 (4.33)
338 (13.3)
355 (13.98)
60
(2.36)
*For reference
51 (2.0)
Template
5.6 (0.22)
25.5 (1.0)
54 (2.12)
5.6 (0.22)
Part No.
704-82570-08
113 (4.45)
66 (2.60)
25
(0.98)
54 (2.13)
50 (1.97)
44.5 (1.75)
93 (3.66)
24.3 (0.95)
Template
138 (5.43)
Descriptions
Part No.
Single application
6Y8-82570-01
1-17
Descriptions
Twin applications
The digital network system for 6Y8 multifunction meter can be used for the fuel injected
outboard motors for 2007 model.
APPLICABLE MODEL
HPDI (Z150-Z300)
mm (in.)
52 (2.05)
130 (5.12)
96 (3.78)
mm (in.)
125 (4.92)
75 (2.95)
50.8 (2)
Ref.
Part No.
6Y8-83688-01
6Y8-83688-11
6Y8-83688-20
Descriptions
1-19
SYSTEM COMPONENTS
INSTALLATION
Gasket
GAUGE INSTALLATION
1. Select the mounting location so that the gauge
is easy to read from the operator, and protected from water-splash, and is a sufficient
clearance behind the dashboard.
The arrow mark is stamped on the back of gauge
to indicate upside.
T.
R.
.
.
(1)
Up mark
2-2
SYSTEM COMPONENTS
INSTALLATION
HUB INSTALLATION
1. Select the mount position near the helm and
tramsom that is dry area and is easy to
connect the wires.
2. Mount the multi-hubs securely using market
obtainable stainless steel hardware so that the
connector end faces down.
UP
DOWN
.
.
Do not allow the waterproof shrinkage portion of wire to bend sharper. Otherwise, the
waterproof structure may damage, causing
the system malfunctioned. The bend of 45
degrees or less is allowed.
Max. 45
Waterproof shrinkage
2-3
SYSTEM COMPONENTS
INSTALLATION
1. Connect the yellow and black bullet connectors to that of the switch panel.
2. Connect the red 2-pin coupler to the nearest
hub.
3. Secure the wire after connection.
51 (2.0)
25.5 (1.0)
44.5 (1.75)
93 (3.66)
24.3 (0.95)
Single template
54 (2.12)
5.6 (0.22)
Twin template
113 (4.45)
66 (2.60)
5.6 (0.22)
50 (1.97)
25
(0.98)
UP
54 (2.13)
138 (5.43)
Triple template
128 (5.04)
24.3 (0.95)
93 (3.66)
25.9 (1.02)
5.6 (0.22)
54 (2
.13)
2-4
SINGLE-ENGINE WIRING
GPS
NMEA
0183
(+)
(GND)
(WHT)
G
R
CONNECTOR DESCRIPTION
TACH
(RED)
W
(BLK)
Trim
sender
FUEL TANK
P/B
Single-hub
with resistor
ECU
Speed sensor
Coolant press.
sensor (OP)
2-5
B
P
(GRY)
SPEED/FUEL
Fuse(10A)
Resistor Cap
Y
B
Y
Multi-hub
P/B
GPS
NMEA
0183
(+)
(GND)
W
L
B
R
TACH
TACH
L
(WHT)
CONNECTOR DESCRIPTION
B
W
L
(GRY)
SPEED/FUEL
Fuse(10A)
Multi-hub
Y
B
(RED)
Multi-hub
W
(BLK)
Trim
sender
Trim
sender
Cap
Coolant
press. sensor
(OP)
Speed sensor
Multi-sensor (OP)
ECU
ECU
Coolant
press. sensor
(OP)
2-6
Resistor
Y
B
FUEL TANK
B/P
150
50-60
100
115
2-8
100
Remove the white 4-pin cap, and connect the
pigtail bus wire to the white 4-pin coupler of engine wire-harness.
50-60
Remove the white 4-pin cap, and connect the
pigtail bus wire to the white 4-pin coupler of engine wire-harness.
For F115
Pigtail bus wire
Trim wire
Flushing hose
b
Plastic band
Fuel cooling
hose
a
Pass the pigtail bus wire into the specified position of grommet, and connect it to the transom
hub.
Pass the pigtail bus wire into the specified position of grommet, and connect it to the transom
hub.
2-9
F200, F225
Remove the white 4-pin cap, and connect the
pigtail bus wire to the white 4-pin coupler of engine wire-harness.
Pass the pigtail bus wire into the specified position of grommet, and connect it to the transom
hub.
Pass the pigtail bus wire into the specified position of grommet, and connect it to the transom
hub.
2-10
HPDI models
Pass the pigtail bus wire into the specified position of grommet, and connect it to the transom
hub.
Secure the pigtail bus wire to the 10-pin main
harness using a plastic band.
Plastic band
Pass the pigtail bus wire into the specified position of grommet, and connect it to the transom
hub.
Pigtail bus wire
2-11
..
Speed data can be input from a NMEA 0183 compatible GPS unit.
After the coolant pressure sensor is installed, set up the tachometer to show the coolant
pressure gauge.
b
c
d
Part name
P/N
Qty
Speed sensor
6Y5-8366B-00
Connector 3
60V-8366D-00
Rubber seal 2
60V-42629-00
Remarks
For speed sensor
From 100 to 250
From 150 to 250
90445-07017
90447-07013
g
h
i
97595-06516
Clamp
90465-11M10
90109-06M81
For 200-250
Installation manual
6Y5-2819K-90
English
2-12
w
e
r
t
y
u
i
o
!0
!1
Part name
Coolant pressure sensor
P/N
Qty
6Y5-8366B-00
Remarks
Connector 3
60V-8366D-00
Adapter
60V-83667-00
Gasket
90430-14115
For adapter
90445-07018
90447-07015
95895-06025
For 100-115
Clamp
90465-11M10
97595-06516
For 50-60
Installation manual
6Y5-2819K-90
English
!0
!1
150-250
KIT P/N: 69J-8A4L0-00
Ref.
w
e
r
t
P/N
Qty
Part name
6Y5-8366B-00
Connector 2 (Short)
63P-8366C-00
Gasket
90430-14115
Installation manual
6Y5-2819K-90
Remarks
2-13
.
.
..
Do not tighten the sensor using its plastic portion. Therefore, the sensor can result in damage.
Tighten the sensor using metallic hexagon portion.
Check the rubber seal in 3-P coupler for proper position before the coupler is connected to the
optional sensor.
Check the joints for water leakage after the optional sensor has been installed.
Do not allow the wires and/or tubes to interfere with moving parts and/or sharper edges, and to
make loose wiring.
For detail information to install the sensors, see the installation manual (P/N : 6Y5-2819K-90) supplied with the sensor kit.
2-14
4 Adapter
T.
R.
!0 Clamp
T.
R.
A
3 Connector3
6 Hose
!0 Clamp
7 Corrugated tube
[cut to 45 cm (18 in.)]
!1 Bolt
T.
R.
h Clamp
W
f Speedometer hose
2 Coolant press.
sensor
3 Connector3
c Connector3
g Bolt
T.
R.
T.
R.
View from A
1.
2.
3.
4.
5.
2-15
Speedometer hose
Speedometer hose
f Corrugated tube
Plate
g Bolt
T.
R.
R.
9 Bolt
T.
R.
4 Adapter
3 Connector3
!0 Clamp
T.
R.
6 Hose
!0 Clamp
7 Corrugated tube
[cut to 24 cm (9 in.)]
R.
5 Gasket
1 Plug
c Connector3
h Clamp
Speedometer hose
32 cm (13 in.)
Clamp
(Position 10 cm (4 in.)
from the end of pigtail bus
wire coupler)
f Corrugated tube
[cut to 35 cm (14 in.)]
1.
2.
3.
4.
5.
Remove the speedometer hose from the rigging grommet, and put the hose into the bottom cowl.
Cut out the speedometer hose 32 cm (13 in.) from its end.
Install the speed sensor b to the connector3 c with the specific torque.
Install the connector3 c with sensor using the bolt g to the exhaust cover with specific torque.
Cut off the corrugated tube f to the specific length.
Install the speedometer hose with corrugated tube f to the connector3 c, and secure the hose with the clamp h.
Remove the coupler marked S from the holder, and connect it to the speed sensor b after removing the 3-pin cap.
Install the rubber seal2 d into the rigging grommet to waterproof.
2-16
d Rubber seal2
Speedometer hose
Clamp
(Existing)
2 Coolant press.
sensor
f Corrugated tube
T.
R.
9 Bolt
4 Adapter
T.
R.
W
T.
R.
6 Hose
3 Connector3
!0 Clamp
!0 Clamp
1 Plug
[cut to 24 cm (9 in.)]
R.
Clamp
(Existing)
c Connector3
h Clamp
Speedometer hose
36 cm (14 in.)
g Bolt
f Corrugated tube
[cut to 40 cm (16 in.)]
5 Gasket
Clamp
(Position 10 cm (4 in.)
from the end of pigtail bus
wire coupler)
1.
2.
3.
4.
5.
Remove the speedometer hose from the rigging grommet, and put the hose into the bottom cowl.
Cut out the speedometer hose 36 cm (14 in.) from its end.
Install the speed sensor b to the connector3 c with the specific torque.
Install the connector3 c with sensor using the bolt g to the exhaust cover with specific torque.
Cut off the corrugated tube f to the specific length.
Install the speedometer hose with corrugated tube f to the connector3 c, and secure the hose with the clamp h.
Remove the coupler marked S from the holder, and connect it to the speed sensor b after removing the 3-pin cap.
Install the rubber seal2 d into the rigging grommet to waterproof.
2-17
1 Plug
W mark for
Coolant press.
sensor
T.
4 Connector2
T.
R.
f Corrugated tube
[cut to 27 cm (11 in.)]
5 Gasket
Speed sensor coupler
b Speed sensor
c Connector3
T.
R.
S mark for
Speed sensor
g Bolt
e Hose
[cut to 30 cm (12 in.)]
h Clamp
h Clamp
T.
R.
f Corrugated tube
[cut to 30 cm (12 in.)]
Speedometer hose
3 mm (0.12 in.)
d Rubber seal2
Remove the speedometer hose from the rigging grommet, and put the hose into the bottom cowl.
Cut out 3 mm (0.12 in.) from the end of nipple of speedometer hose.
Cut off the hose e and the corrugated tube f to the specific length, and install them to the speedometer hose to extend.
Install the speed sensor b to the connector3 c with the specific torque.
Install the connector3 c with sensor using the bolt g to the cylinder body with specific torque.
Install the hose e with corrugated tube f to the connector3 c, and secure the hose with the clamps h.
Remove the coupler marked S from the holder, and connect it to the speed sensor b after removing the 3-pin cap.
Install the rubber seal2 d into the rigging grommet to waterproof.
2-18
b Speed sensor
18 Nm, 1.8 kgfm, 13 ftIb
T.
R.
T.
R.
i Bolt
a Bolt
S mark for
Speed sensor
c Connector3 c Connector3
h Clamp
e Hose
[cut to 50 mm (2 in.)]
Speedometer hose
5 Gasket
3 mm
(0.12 in.)
1 Plug
4 Connector2
T.
T.
R.
f Corrugated tube
[cut to 60 cm (24 in.)]
View from A
2-20
.
.
(4 seconds)
3-2
ROUND TACHOMETER
CUSTOMIZATION
The meters are set at the factory to -1- (engine number 1).
To reset an engine number, see Resetting
engine number.
4.
3-12
ROUND TACHOMETER
CUSTOMIZATION
4.
-1- (ABYC-US)
4.
-2- (EUROPE)
+
(1 second): To adjust the trim
angle to zero using the current trim position
as the standard value and return to the normal display.
-3- (YAMAHA)
Press the
button for 1 second from step 3
to cancel the adjustment of the trim angle to zero
and return to the normal display.
TRIP
FLOW
ECON
TTL
Blink
5.
3-13
set
set
mode
KEY SW
SW OFF
SW OFF
SW OFF
SW OFF
SW OFF
SW ON
If Maintenance
period has come
Wake up
Mode
Maintenance
Mode
Monitor mode
set
or
mode
mode
mode
mode
mode
(For F50-F100)
mode
set
Up 50 rpm
1 sec.
Coolant press.
Hour
1 sec.
mode
mode
(Required
OP sensor)
mode
mode
Coolant temp.
Voltage
Down 50 rpm
set
set
set
mode
set
Switches
graph or value
set
1 sec. to set 0
mode
set
1 sec. to cancel
set
set
1 sec. to cancel
Custom Mode
Maintenance
reset Mode
mode
1 sec.
Shows 01
Trim
0-set Mode
mode
Engine
select Mode
1 sec.
Shows 02
Shows 03
mode
mode
If Warning
has detected
Blinks applicable
symbol
set
or
mode
Stops buzzering
set
set
Selects ENG
1 sec.
When Warning
has removed
Warning
Mode
mode
set
mode
mode
Dimmer
Mode
With warning mode,
set
mode or
No input for 5 sec.
mode
set
Diagnosis
Mode
Shows code No.
Troll Mode
mode
10 sec.
Graph
Elapsed hour
Level 1 & OFF
No. 1
Coolant temp.
4-6
Increases brightness
Swiches illumination ON or OFF
Changes code
set
set
mode
KEY SW
SW OFF
SW OFF
SW OFF
SW ON
Wake up Mode
Checks All display
mode
Speed sensor
Mode
1 sec.
set
set
4 sec.
Monitor mode
mode
mode
Clock
set
mode
set
mode
mode
Fuel flow
Trip distance
(Required GPS)
Repeatedly
to select digit
Adjusts digit
set
mode
Fuel economy
set
mode
1 sec. to reset
mode
1 sec. to reset
mode
4 sec.
set
mode
Fuel consumption
mode
Water surface
temp.
Water depth
mode
1 sec. to reset
set
set
1 sec. to set
mode
1 sec.
Custom Mode
Unit Mode
mode
Fuel sensor
Mode
1 sec.
Shows 01
mode
set
set
Shows 02
mode
Selects unit
mode
Default
Selects sensor
(ABYC, Yamaha, EUR)
mode
set
mode
Shows 03
mode
1 sec.
set
mode
mile
gph
mpg
gallon
F
ft
ON
mph
All automatic
ABYC
Level 1 & OFF
Fuel flow mode
Fuel compensater
Mode
Dimmer
Mode
mode
set
Increases brightness
Swiches illumination ON or OFF
4-7