Академический Документы
Профессиональный Документы
Культура Документы
1 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
What's New?
Forum
New Posts:
Satellite Forums
Private Messages
FAQ
Garage Forum
Calendar
Community
Cable Forum
Apple Forum
Forum Actions
Quick Links
Downloads
Chatbox
Videos
Android Forum
Type Here...
Advanced Search
Welcome, briangsm
Forum
The Garage
Notifications: 14
My Profile
Settings
Log Out
+ Reply to Thread
Carprog Mcu Reflash Step by step
Here is how to reflash CARPROG Mcu AT91SAM7S256 step by step, first ...
Last
Page 1 of 12 1 2 3 4 5 6 11 ...
3 Likes
LinkBack
Thread Tools
Search Thread
Display
#1
audiotek
Join Date:
May 2011
Location:
Mexico
Posts:
149
Here is how to reflash CARPROG Mcu AT91SAM7S256 step by step, first of all I wish to thanks to
lupu_sandu, elchip, autocargo, Tachonow, carradio2001 and all DK forum members who made this
possible.
I bought my Carprog clone 4.01 from digi_obd but after about 50 uses starts a counter: "260 uses left update hardware to synchronize" and was decreasing, anyway 260 uses is big number to recover the
investment (us $209 dlls), the programmer was paid before the counter starts.
Thanks:
Top Poster
Downloads:
Uploads:
Carefully lift the pin 55 (reset) of the mcu and solder a wire and secure it with a small ammount of
silicone (you don't want to broke the pin in the process).
Connect the Carprog (with the pin 55 dissconected) to the 12v supply, wait about 10 seconds and
connect the wire from pin 55 to Vcc (3.3V) in Carprog:
2013-04-08 19:46
2 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Wait from 5 to 10 seconds after connect the 12v supply, the flash content will be erased and the Jtag
option of the Mcu will be enabled now. If not work leave connected for about 3 to 5 minutes. Disconnect
the 12v supply from carprog and remove the pin 55 wire from vcc. The pin 55 must remain disconnected
until the programming process is done.
Install the H-JTAG software in your pc.
Reply
The Following User Says Thank You to audiotek For This Useful Post:
ligno1 (Yesterday)
#2
audiotek
Top Poster
2013-04-08 19:46
3 z 12
Join Date:
May 2011
Location:
Mexico
Posts:
149
Thanks:
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Carprog Pinout:
Downloads:
Uploads:
Jtag Pinout:
And here is the Carprog connected to the JTAG programmer (note that the pin 55 wire is disconnected):
Reply
#3
audiotek
Top Poster
2013-04-08 19:46
4 z 12
Join Date:
May 2011
Location:
Mexico
Posts:
149
Thanks:
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Downloads:
Uploads:
TAP configuration:
Target manager:
Now connect the carprog to JTag programmer and 12v supply and press "Detect Target" in H-TAG
server, now the Carprog Mcu is detected!!!:
2013-04-08 19:46
5 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Reply
#4
audiotek
Top Poster
Join Date:
May 2011
Location:
Mexico
Posts:
149
Thanks:
Downloads:
Uploads:
-Go to "4 Programming" in the programming wizzard and press "Check" to verify the communication
with the target mcu, if all is ok the values must be:
Flash: AT91SAM7S256 0x270D0940
Target: ARM7TDMI LITTLE-ENDIAN
-In "Type" select: "Plain Binary Format"
-In "Dst Addr" select: "Flash Base Address"
-In "Src File" select the location of the AT91SAM7S256 bin in your hard drive.:
2013-04-08 19:46
6 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
If the progrmming was succefull you will receive the next message:
The programming process is finished!!, disconnect the 12v supply, then disconnect the programmer from
carprog, solder the pin 55 wire to Ground (check the picture) and put back the AT88SC eeprom,
reassemble the carprog and test it.
I already made some further tests and the Carprog works well with any version of the software and the
COUNTER IS GONE!!!
Tested with versions: 3.75, 4.0, 4.1, 4.5, 4.85 and 4.86, the counter never start again.
2013-04-08 19:46
7 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Reply
#5
audiotek
Top Poster
Join Date:
May 2011
Location:
Mexico
Posts:
149
Thanks:
Downloads:
Uploads:
I used the Carprog pins from 15 to 21, those pins are useless for the programmer or any adapter, they
are disconnected:
I used a "selector" like the desktop's pc for bios, to select the programming mode, in picture from left to
right: 1, 2 3, if the jumper is placed at pins 1 and 2, the pin 55 (reset) from the AT91 is shorted to
ground, preventing deprogramming or programming the MCU, if the jumper is placed at pins 2 and 3 the
pin 55 is shorted to vcc 3.3v and the Mcu is placed in ERASE MODE. Without jumper the mcu is placed
in programming mode:
2013-04-08 19:46
8 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Now is probably a waste of time, in the near future will save me some time but from now I can reflash
the AT91 in less than 5 minutes.
Update: I forgot to mention that I doesn't need to remove the AT88SC eeprom to ERASE/REFLASH the
AT91 mcu. After that the Carprog works well. This is MY OWN experience, so, If you want to do the
same, do it at YOUR OWN risk.
Last edited by audiotek; 4th September, 2012 at 07:40 PM. Reason: title
Reply
#6
olegario
DK Veteran
Join Date:
Apr 2010
Location:
LT & ES
Posts:
373
Thanks:
And how you plan to remove fast AT88SC eeprom, to protect it's content?
Downloads:
Uploads:
Thanks
Reply
#7
ahadi
DK Veteran
Attached Thumbnails
Join Date:
Sep 2009
Location:
JerusalemPalestine
Posts:
384
Thanks:
Downloads:
Uploads:
Thanks
Reply
#8
carradio2001
DK Veteran
2013-04-08 19:46
9 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
I made a modification to my Carprog clone for fast reprogramming, if I need to do it again will not be
necessary to open it again and redo all connection every time I want or need to reprogram
Nov 2009
Location:
France
Posts:
335
Thanks:
Downloads:
Uploads:
Thanks
Reply
#9
audiotek
Top Poster
Join Date:
May 2011
Location:
Mexico
Posts:
149
Thanks:
Downloads:
Uploads:
And how you plan to remove fast AT88SC eeprom, to protect it's content?
Reply
#10
audiotek
Top Poster
Join Date:
May 2011
Location:
Mexico
Posts:
149
Thanks:
Downloads:
Uploads:
As I said at the end of the post: "Now is probably a waste of time, in the near future will save me some
time but from now I can reflash the AT91 in less than 5 minutes." I doesn't share this with the intention
that other people do the same, it's your/they choice and risk anyway, it's only to comment that it's
possible reflash the carprog MCU without removing the AT88SC eeprom (at my own experience). BR...
2013-04-08 19:46
10 z 12
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Thanks
Reply
#11
carradio2001
DK Veteran
Join Date:
Nov 2009
Location:
France
Posts:
335
Thanks:
Downloads:
0
Uploads:
Thanks
Reply
#12
coops43
Newbie
Join Date:
Feb 2010
Posts:
Thanks:
Carprog Software
Does this mean that the carprog software will have all the functions of software version 4.86?
If so does anyone know where I can get the software from please?
Downloads:
0
Uploads:
Thanks
Reply
#13
radsky
Top Poster
Does this mean that the carprog software will have all the functions of software version 4.86?
no
If so does anyone know where I can get the software from please?
Join Date:
May 2012
Location:
Earth
Posts:
182
Thanks:
Downloads:
Uploads:
Thanks
Reply
#14
coops43
Newbie
Join Date:
Feb 2010
no
2013-04-08 19:46
11 z 12
Posts:
Thanks:
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Downloads:
Uploads:
Thanks
Reply
#15
guilhermegti
Junior Member
Join Date:
Jul 2011
Posts:
27
Thanks:
Attached Thumbnails
Thanked 5 Times in 2 Posts
30
Downloads:
Uploads:
Thanks
Reply
Page 1 of 12 1 2 3 4 5 6 11 ...
+ Reply to Thread
Last
Quick Reply
There are currently 1 users browsing this thread. (1 members and 0 guests)
briangsm
Tags for this Thread
None
View Tag Cloud
Posting Permissions
You may
You may
You may
You may
BB code is On
Smilies are On
[IMG] code is On
[VIDEO] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On
Forum Rules
2013-04-08 19:46
12 z 12
Contact Us
Digital Kaos
http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-st...
Sitemap
Top
-- DarkCore - Blue
2013-04-08 19:46