Вы находитесь на странице: 1из 2

PERMA IIIJECT

ST G-RESIII / GATATYST

PffiA
SEMI RIGID POLYURETHANE INJECTION GROUTING SYSTEM
Perma injection STC

is a

components the reactor/catalyst can be


adjusted frgm six to ten percent to allow
on site adjustrnent of geltime,

polyurethane

injection grouting system. lt consist of two


eorqponent one being is prepolymer rqsin
and the other being a cbtalyst Tliese two
components are mixed togetherand injected
into the concrete or RCC structure using a
single component pump whethermanual or
motorized. Perma lnject STC when injected
into the concrete forms a semi-rigid and
;ccrxiflexible foam when it comes in ccrntact
wiih water or rnoisture. This foam effectively
stops leakages from the structures.

When injected in the.concrete Perma lnject


STC reacts with water or moisture to form a
semi-rigid foam which is abouttwentytimes
largerthan the ieacting components. DUring
this reaction wlth water there is aformation
of carbon dioxide gas which makes fte foam
penetrate deep into the fine crevices of the
concrete and seals them effectively. lt also
fills up allcapillaries and honeycombs in the
concrete to " discourage...accumulation of

"water in thiie'poikeis'-at a later stage.


Perma lniect STC is more suited for static
cracks and in situation of heavy leakages.

1. Perma lnject STC seals leakages in all


difficult situations. such as basements,
tunnels and heavily leaking massive
structures,

2. Perma lniect $TG is free from solvents


and fillers. lt is resistantto hydrolysis and
is suitable for use in potable water tanks.
-

3. The productis supplied as two

4. Perrna lniect STC stops the leakage then


and there only instantly, after injection,
there ls no waiting period to wait for
curingtimeetc.

Clean the surface to be waterproofed"affi


remove the plaster or loose concrete in the
area. Assess the leaky area and decide the
injection nozzle pattern. The leakage could
be either from a horizontal or from a vertical
crack. Drill holes on either side of the crack
at an inclination of 450 inclined towards the
center of the crack at an interval of I inches
center to center. Always start from the
lowest point and progress upwards. ln the
drilled holes fii the packers effectively. ln
weak concretO, the,,drilled holes becomes
larger than desired, in such cases the
packers may notfittightlyto leak- proof it. lf
this happens then grout the surrounding of
the packers witlrthe stiff consistency paste
of Perma Plug. Mix the two components the

prepolymer resin and the catalyst. The


catalyst can be adjusted between 6 to 1010
to adiust the gel time depending upon the
speed and the site condiUons. lnject the
product into the packer from the manual or
motorized high pressure pump tillthe foam
is observed,from the neighboring holes.
Keep the counter pressure on through the
noule nipples tilt the reaction is complete
and the foam'and set. Move on to the nefi
packer and continue the process. Clean the
pump and the equipment with Perma lnject
Clean, .a special material specially
d

eveloped for cleanin g polytureth anes.

PREPOLYMER

REACTOR

NORM

0.889
21 mPa.s

EN

VISCOSITY

1.158
96 mPa.s

FLASH POINT

>

>

COLOR

BROWN

SPECIFIC GRAVITY

OF
CATALYST

OUANTITY

1500C

POLYMERISATION

SECONDS

SECONDS

15

70
55
45

12

09

EN lS0 3219: 1994

1500C

TRANSPARENT

REACTION

6Yo
.8%
1070

lS0 2811 -2:2002

The workers should use face masks and


hand glows to avoid direct breathing of the
toxic vapors and to avoid direct contact with
skin. Ventilate the working area adequately
and maintain.over all hygienic conditions.
Clean the,tools and the pumps immediately

afteruse.
Perma lnject STC is supplied in packing of
25 Kg for prepolymer resin and the catalyst
in 2.5 ltr packs and 10 kg for prepolymer
resin and the catalyst in 1 ltr packs.

months from the date of manufacture.


These products are both ternperature and
moisture sensitive. Hence it is utnost
important that these products are stored in

DRY

Should you find the behaviour of the product

different from the'normalfeel or the claims


with the.literature, stop the use of the
product, cordon'off all such product and

inform Perma with a complaint letter stating


the problem, batch number etc. lf the
product is used in spite of observed variance
the responsibility shall be with the user.

OONDITION:S BETWEEN

TEMPERATURES 1Oto3O"C

PERMA CONSTRUCTIONS AIDS PVT. LTD.


'l

/ 612, Nirmal Corporate Centre,


Mulund (W), Mumbai- 400 080, tndia.
Tel.:91-22-2591 8911 I 2561 4690
Fax. : 2590 3008
E-mail: info@permaindia.com
Visit us at www.permaindia.com '
61

DISTRIBUTOR ADDRESS

Вам также может понравиться