Академический Документы
Профессиональный Документы
Культура Документы
Dimensions
General information
X-EHS MX
Material specifications
X-ECC MX
2.5 m
Ls
L
1.8
o 6.8
o 6.8
X-GHP 20/24
1.8
o3
14
15.8
X-U 16/22
2.4
Ls
L
Applications
Example
Hanger systems for light cable trays, etc.
Threaded rod attachments
Wire attachments
These fasteners are not recommended for fastening of suspended
ceilings.
These zinc coated fasteners are not suitable for long-term service
outdoors or in otherwise corrosive environments.
01 / 2015
243
X-EHSMX, X-ECCMX
Load data
Recommended loads on concrete
Fastener designation
X-ECC MX
0.05 (Nrec*)
0.1 (Vrec)
X-EHS MX
0.1
Conditions:
Fastened with X-GHP 20/24 or X-U 22
Minimum 5 fastenings per fastened unit (normal weight concrete).
All visible failures must be replaced.
With lightweight concrete base material and appropriate washers, greater loading may be
possible, please contact Hilti.
Predominantly static loading.
Observance of all application limitations and recommendations.
Recommended loads on steel
Fastener designation
0.45
Application requirements
Thickness of base material
hmin = 80 mm
hmin = 60 mm
Steel
tIl 4 mm
tII
Concrete
X-U:
X-GHP:
Corrosion information
These zinc-coated fasteners are not suitable for long-term service outdoors or in otherwise
corrosive environments.
For further detailed information on corrosion see relevant chapter in Direct Fastening
Principles and Technique section.
244
01 / 2015
X-EHSMX, X-ECCMX
Application limits
Fastening to steel
X-EGN 14
20
Steel thickness, tII [mm]
18
16
14
12
10
S235
S275
8
6
4
400
S355
450
500
550
600
650
Steel strength, Rm [N/mm2]
700
750
Fastener program
Fastener selection
Nail
Base material
Designation
Concrete
Shank
ds [mm]
X-GHP 20 MX 3.0
Shank length
Ls [mm]
20
21.8
X-GHP 24 MX 3,0
24
25,8
X-EGN 14 MX 3.0
14
15.8
X-U 22 MX 4.0 22
X-U 16 MX 4.0 16
Steel
L [mm
24.4
18.4
G
01 / 2015
245
X-EHSMX, X-ECCMX
Designation
X-EHS M6 MX 272073
Ceiling clip
GX nails
DX Nails
Item no.
X-EHS M4 MX 273367
X-EHS W6 MX 228341
X-EHS M8 MX 273368
X-EGN 14 MX
228342
338872
X-GHP 20 MX 285890
X-GHP 24 MX 438945
X-U 16 MX
X-U 22 MX
237344
237346
System recommendation
DX tools: Steel:
6.8/11M yellow or red cartridge
Concrete: 6.8/11M yellow cartridge on green/ fresh and standard concrete
6.8/11M yellow or red cartridge on precast, old and hard concrete
GX 120-ME tool:
GX 100-E tool:
hNVS = 48 mm
hNVS
hNVS
X-EHS MX
hNVS = 48 mm
G
246
01 / 2015