Академический Документы
Профессиональный Документы
Культура Документы
O.J. Braimah, 2P.A. Osanaiye.3 P.E. Omaku 4Y.K. Saheed 5S.A. Eshimokhai
Department of Statistics, Abdur-Raheem college of Advanced Studies Igbaja, Ilorin, Kwara State, Nigeria.
Department of Statistics, University of Ilorin, P.M.B 1515 Ilorin, Ilorin, Kwara State, Nigeria. 3Department of
Mathematics and Statics, Federal Polytechnic Nasarawa, Nasarawa State, Nigeria.
4
Department of Computer Science, Abdur-Raheem college of Advanced Studies Igbaja, Ilorin, Kwara State,
Nigeria.
5
Department of Safety and Environmental Management, Edinburgh Napier University, Scotland.
ABSTRACT: This study is aimed at designing Exponentially Weighted Moving average (EWMA) control
chart in monitoring road crashes. The data used in this study is a secondary data from the accident record
office of the Federal Road Safety Commission (FRSC), Zone RS8 Command Headquarter, Offa Road, GRA,
Ilorin, Kwara State, Nigeria for the period of January, 2000 to December, 2010. Cumulative Exponentially
Weighted Moving Average (EWMA) control char scheme was designed and used to study the rate of road
crashes. Finally, the performance of the control chart schemes was compared by varying the weighted
parameter (w=0.15, 0.20 and 0.30). It was observed that EWMA control chart scheme is sensitive in detecting
small shift in the process but more sensitive in detecting shift in the process mean with higher weighted
parameter (W). Therefore, the higher the weighted parameter, the faster it detects an out of control signal. Thus
providing validation of the methodology employed to set up Minitab using Neubauer table in determining the
weighted parameter, limit q of the EWMA chart and the nominal ARL.
I.
INTRODUCTION
The mandate of Federal Road Safety Commission (FRSC) which is reducing road accidents on our
roads can be viewed as rendering services to the citizens of Nigeria and the more the road accidents are
curtailed, the better the costumers (citizens) are satisfied. Shewhart chart has been widely used in determining
shift in a process, however the main disadvantage of any of Shewhart charts is that they use only the last
information of the combined process and ignore any other process given by the sequence of all points. This
characteristic makes Shewhart control charts relatively insensitive to a small change in a process, because the
cumulative or weight of the previous observation are disregarded. Small changes could be detected through
CUSUM, EWMA and Moving Average control charts. These charts could be used as a complementary tool for
X-bar, through which, small and large changes could be detected. Some authors, such as Dugans (1974), Lucas
(1976), stated that the cumulative sum control chart is much more efficient than the usual
control chart
for detecting small variations in the average. Other authors including Crowders (1987) presented the
exponentially weighted moving average control chart, as good choice to detect small change in process average.
Various modification and supplemental criteria have also suggested that control charts based on moving average
is also an effective chart in detecting small process change.In this study, road crashes from the Accidents Record
Office of Federal Road Safety Commission (FRSC) which comprises of Kwara, Kogi and Ekiti state is studied
using cumulative-sum (CUSUM), exponentially weighted moving average (EWMA) and moving average
control charts.
II.
www.ijmsi.org
1|Page
where
The above equation is due to Roberts (1959).
The use of this control chart was first published in the article Control chart tests based on geometric moving
averages (Roberts, 1959). While Shewhart charts only consider the most recent data point in testing to
determine if statistical limits have been exceeded, EWMA charts consider all previous points using a weighing
factor that makes the outcome more influenced by recent points. In statistical quality control, the EWMA chart
(or exponentially-weighted moving average chart) is a type of control chart used to monitor either variables or
attributes-type data. While other control charts treat rational subgroups of samples individually, the EWMA
chart tracks the exponentially-weighted moving average of all prior samples. EWMA weights samples in
geometrically decreasing order so that the most recent samples are weighted most highly while the most distant
samples contribute very little. Although EWMA chart assumes normal distribution, it is relatively robust in the
face of non-normality. The chart monitors only the process mean. EWMA Charts are generally used for
detecting small shifts in the process mean and they detect shifts of 0.5sigma to 2sigma much faster than
Shewhart charts with the same sample size. In brief, after multiplication by a weighting factor w, the current
measurement is added to the sum of all former measurements, which is weighted with (1 - w). Thus, at each time
t (t = 1, 2,... ), the test statistic .
Basically, the method is to form a new moving average at each sample point by calculating a weighted average
of new value and previous moving-average. Therefore, in exponentially weighted moving average chart, all of
the past data has some effect on the current value, but it rapidly loses influence.
Consider the following notations:
= Exponentially Weighted Moving Average
= EWMA weighted parameter (
)
0 = Process mean
= jth measure of ith subgroup, with
= Process standard deviation
= Sample size of ith group
q=sigma limit
= Mean of measurement in ith subgroup. If
, then subgroup mean reduce to the observation in the group
Each point on the chart indicates the value of exponentially weighted moving average (EWMA) for the
subgroup. The EWMA for the ith subgroup
is defined recursively as:
, where w is the weighted parameter (
).
III.
By default, the central line on an EWMA chart indicates an estimate for , which is computed as:
2
The default limits are computed as
The upper and lower control limits are
3
...4
where n is the subgroup size (1).
www.ijmsi.org
2|Page
Figure 1
In order to accurately compare EWMA control chart techniques, the same ARL value must be used for the
design.
A graphical method for determining the ARL for an EWMA control chart is seen in Fig. 2 and 3 below,
Neubauer (1997). One can obtain the weighting factor w as a function of the desired shift sensitivity of the
chart. For a shift of 1.0standard deviation,for example, a weighting factor of 0.15 can be obtained from the
chart as shown in figure 2 and we set ARL at 45, using Fig. 3, the sigma limit (q) was obtained to be 2.30.
Fig.2: Optimal w for EWMA charts according to the shift d from Neubauer (1997)
www.ijmsi.org
3|Page
IV.
DATA ANALYSIS
The analysis of the data (number of road crashes) obtained from the Federal Road Safety Commission
(FRSC) were considered using EWMA control chart scheme
The overall mean per month is approximately
, the standard deviation from the historical data is
and the subgroup size (n) is 1.
EWMA CHART METHOD
The EWMA statistic was calculated using three different values of w (weighted parameters), 0.15, 0.20
and 0.30 so as to come out with the most appropriate one.
The following shows how we set up an EWMA-chart by the three-step procedure:
Select an in-control Run Length (RL) of 45. This is also the average run length (ARL) of the Westgard
algorithm.
Define the optimum shift to be detected as 1.0, 1.2 and 1.5. Using this and the above ARL, gives a
weighting factor w of 0.15, 0.20 and 0.30 (Fig. 2).
With these selected values derived from Fig. 2, EWMA chart limit (q) were obtained to be2.30, 2.35 and
2.42 from Fig. 3. For one control sample per month (n = 1), the central line, upper control limit (UCL) and
lower control limit (LCL) are calculated as follows.
CENTRAL LINE =
=
s
CONTROL LIMITS
=36.51+2.30(23.01)
= 36.51+15.07= 51.58
=36.51-2.30(23.01)
= 36.51-15.07= 21.44
Using the same procedure, the control limits calculation for w = 0.1, 0.2 and 0.3 is shown in table 1 below.
TABLE OF EWMA CONTROL LIMITS
WEIGHTED/SIGMA
LIMIT VALUE
w = 0.15
q = 2.30
w = 0.20
q = 2.35
w = 0.30
q = 2.42
LCL
21.44
CONTROL LIMITS
CL
35.51
UCL
51.58
18.49
36.51
54.53
13.12
36.51
59.90
Table 1.
COMPUTATION OF EWMA STATISTIC
The EWMA statistic is calculated using three (3) different values of w (weighted parameter) so as to
come out of the appropriate value.
The statistic is
Zi =wxi + (1-w)
,0<w1
For w =0.15,
Z1 = 0.15(15) + (1 -0.15)36.51=33.28
Z2 = 0.15(31) + (1 0.15)33.28=32.948
Using the same procedure, the EWMA statistic for w =0.15, 0.20 and 0.30 is shown in table 2.
www.ijmsi.org
4|Page
Fig. 4.
Fig. 5.
www.ijmsi.org
5|Page
Fig. 6.
From the EWMA charts above, the process is out of control for the three values of weighted parameter (w) and
they indicate out of control signals at different points. For w =0.15 and 0.20, both charts detected the first out of
control signal at point 119 which correspond to November, 2009 while for w= 0.30, the first out of control
signal was at sample point 118 which corresponds to October, 2009. Therefore, the higher the weighted
parameter, the faster it detects an out of control signal. Thus providing validation of the methodology employed
to set up Minitab using Neubauer table in determining the weighted parameter, limit q of the EWMA chart and
the nominal ARL.Therefore, the higher the weighted parameter, the faster it detects an out of control signal.
COMPUTATION OF EWMA STATISTIC ON ROAD TRAFFIC CRASHES IN ZONE RS8 FOR THE
YEAR 2001 to 2010
Sample No.
(i)
No of
(Xt)
Road Crashes
zt = [wXi + (1 - w)zt-1]
w=0.15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
15
31
46
55
44
23
15
11
23
28
44
44
12
30
41
39
45
33
21
17
28
37
22
50
15
12
31
33.28
32.94
34.90
37.92
38.83
36.46
33.24
29.90
28.87
28.74
31.03
32.98
29.83
29.86
31.53
32.65
34.50
34.28
32.29
30.00
29.70
30.80
29.50
32.58
29.94
27.25
27.81
www.ijmsi.org
w=0.3
w=0.20
32.21
31.97
34.77
38.82
42.06
38.25
33.60
29.08
27.86
27.89
31.11
33.69
29.35
29.48
31.79
33.23
35.58
35.07
32.25
29.20
28.96
29.97
28.38
32.70
29.16
25.73
26.78
30.06
30.34
35.04
41.03
41.93
36.24
29.87
24.21
23.85
25.09
30.76
34.74
27.91
28.54
32.28
34.29
37.51
36.15
31.61
27.23
27.46
30.32
27.83
20.98
19.18
17.03
21.22
6|Page
27
35
22
20
18
23
6
20
28
24
17
38
57
38
16
26
14
26
48
37
50
22
21
35
52
53
27
22
21
23
48
33
64
21
30
22
38
36
38
31
28
22
46
51
61
24
39
20
33
40
30
29
31
18
28
39
46
19
35
35
37
41
39
25
21
19
29
36
51
32
27.69
28.79
27.77
26.60
25.31
24.96
22.12
21.80
22.73
22.92
22.03
24.43
29.32
30.62
28.43
28.07
25.96
25.97
29.27
30.43
33.37
31.66
30.06
30.80
33.98
36.83
35.36
33.36
31.51
30.23
32.90
32.92
37.58
35.09
34.33
32.48
33.31
33.71
34.35
33.85
32.97
31.32
33.52
36.12
39.85
37.47
37.70
35.05
34.74
35.53
34.70
33.85
33.42
31.12
30.65
31.90
34.02
31.77
32.25
32.66
33.31
34.46
35.14
33.62
31.73
29.82
29.70
30.65
33.70
33.45
www.ijmsi.org
26.83
28.46
27.17
25.73
24.19
23.95
20.36
20.29
21.83
22.26
21.21
24.57
31.06
32.44
29.16
28.52
25.62
25.70
30.17
31.53
35.22
32.58
30.26
31.21
35.37
38.90
36.52
33.61
31.09
29.47
33.18
33.14
39.31
35.65
34.52
32.02
33.21
33.77
36.62
33.89
32.71
30.57
33.65
37.13
41.90
38.32
38.45
34.77
34.41
35.53
34.42
33.34
32.87
29.90
29.52
31.41
34.33
31.26
32.01
32.61
33.49
34.99
35.79
33.63
31.11
28.69
28.75
30.20
34.36
33.89
22.95
26.57
25.20
23.64
21.95
22.26
17.38
18.17
21.12
21.98
20.47
25.74
35.12
35.98
29.99
28.79
24.36
24.85
31.79
33.36
38.35
33.44
29.71
31.30
37.51
42.16
37.61
32.93
29.35
27.44
33.61
33.43
42.60
36.12
34.28
30.60
32.83
33.77
35.04
33.83
32.08
29.06
34.14
39.20
45.75
39.22
39.15
33.41
33.28
35.30
33.71
32.30
31.91
27.73
27.81
31.17
35.62
30.63
31.94
32.86
34.10
36.17
37.02
33.41
29.69
26.48
27.24
29.87
36.21
34.94
7|Page
23
34
42
24
52
26
23
36
33
32
133
32
17
23
25
21
37
32
48
31
131
139
116
44
35
31
20
32
35
53
46
59
89
109
113
31.88
32.20
33.67
32.22
35.19
33.81
32.19
32.76
32.80
32.68
47.73
45.37
41.11
38.39
36.38
34.07
34.51
34.13
36.21
35.43
49.77
63.15
71.08
67.02
62.22
57.54
51.91
48.92
46.83
47.76
47.50
49.23
55.20
63.27
70.73
31.71
32.17
34.13
32.11
36.09
34.07
31.85
32.68
32.75
32.60
52.68
48.54
42.23
38.39
35.71
32.77
33.61
33.29
27.43
28.14
48.72
66.77
76.62
70.09
63.08
56.66
49.33
45.86
43.69
45.55
45.65
48.31
45.64
60.65
50.56
31.36
32.15
35.11
31.77
37.84
34.29
30.90
32.42
32.60
32.42
62.60
53.42
42.49
36.64
33.15
29.50
31.75
31.83
36.68
34.98
63.54
86.35
95.24
79.87
66.41
55.79
45.05
41.14
39.29
43.41
44.19
48.63
60.74
75.22
86.55
Table 2
V.
RESULT
EWMA was designed and applied using three (3) different values of weighted parameters/smoothing
constant (w) which are 0.15, 0.20 and 0.30. Table 2 shows the EWMA statistic tabulation. The values of control
limit for the three values of w are show in table 1. The values of Z i (EWMA) were then plotted against the
sample number for the three values of w and the corresponding EWMA control charts are shown in Fig. 4 to 6
respectively. It can be seen from the charts that the process is out of control for the three values of w. For w
=0.15 and 0.20, both charts detected the first out of control signal at point 119 which correspond to November,
2009 while for w= 0.30, the first out of control signal was at sample point 118 which corresponds to October,
2009. Therefore, the higher the weighted parameter, the faster it detects an out of control signal.
VI.
CONCLUSION
The effectiveness of EWMA chart relative to determining shifts in underlying pattern and the
efficiency of the charts relative to the time and expertise required to generate the chart was taken into
consideration. EWMA chart was very capable at detecting changes in the Road Traffic Crashes recurrent
(persistent) pattern when properly configured within Minitab. That is, it is very effective at detecting small
change like mean shift of 1.0 sigma as used in this paper work. In view of our findings, we strongly observed
that EWMA generally provided a slightly faster alarm Since the EWMA methodology detects shift quickly for
this type of dataset, it may be an efficient choice for monitoring it. Conclusively, for such applications within
this organization EWMA can be an efficient tool.
VII.
RECOMMENDATION
From Fig. 4 and 5, the first out of control signal at point 119 corresponding to November, 2009 and
continues to February while from Fig. 6 first out of control signal was at sample point 118 which corresponds to
October, 2009 and also continues to February. These months correspond to the Christmas and New-year
celebration periods in Nigeria when most people use the highways to travel to their home towns. It is then
suggested that the Federal Road Safety Commission (FRSC) and other Agencies who are engaged in road safety
www.ijmsi.org
8|Page
REFERENCES
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
Crowder, S.V (1987, 1989). Design of exponentially weighted moving average schemes. J. of Qual Technology 21, pp. 155-162.
Crowder, S. V. (1987). A simple method for studyingrun length distributions of exponentially weighted moving average charts.
Technometrics, 29, pp. 401407.
Dugans, A.J. (1974). Quality control and industrial statistics, 5th edition.
Hawkins, D. M., Qiu, P., and Kang, C.-W. The Changepoint Model for Statistical Process Control, Journal of Quality
Technology, 35, pp. 355-365
Lucas JM, Saccucci MS (1990). Exponentially Weighted Moving Average Control Schemes: Properties and Enhancements.
Technometrics, 32, pp. 1-12.
Montgomery, D.C. (1996). Introduction to statistical quality control, 3rd edition, Johnson Wiley & Sons.
Neubauer (1997). Optimal weighted parameter for EWMA chart according to the shift, Technometrics, Vol.22.S
Osanaiye, P.A. (2010). Quality control analysis and management, STA 658.
Pages, E.S (1954). Continous inspection Scheme, Biometrica, 41, pp.100
Roberts, S. W. (1959). Control Chart Tests Based on Geometric Moving Averages, Technomearics, 1, pp. 239-250.
Robinson, P.B. and HO, T.Y. (1978) - Average run lengths of geometric moving average charts by numerical
methods,Technometrics, 20, pp 8593.
www.jmu.edu
www.uc.edu
www.minitab.com
www.anygeth.com
www.engineerlive.com
www.google.com
www.itl.nist.gov
www.ijmsi.org
9|Page