Академический Документы
Профессиональный Документы
Культура Документы
MODEL KLIK2U
STOP
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or
play with remote controls.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no
obstructions to door travel.
ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to
cross path of moving gate or door.
TYPE 2
Genie, Linear and Moore-O-Matic garage
door openers or receivers with: 2 position
DIP switches.
Opener
Opener
TYPE 3
Chamberlain, Sears Craftsman, LiftMaster,
Master Mechanic and Do It garage door
openers or receivers with: Yellow, white or
grey Smart/Learn buttons.
Opener
TYPE 4
Chamberlain, Sears Craftsman, LiftMaster,
Master Mechanic, Do It, Genie
Intellicode**, Overhead Door, Stanley,
Wayne Dalton or Linear garage door
openers with: Smart/Learn button.
Opener
ON
Remote Control
Remote Control
Remote Control
ON
PROGRAMMING:
TYPE 1
1. Select and write a 4-digit PIN:
__ __ __ __
2. Determine your opener ID using the list
below.
ID
DIP Switch Type
11 = DIP switch garage door openers
(U.S.)
12 = 9 DIP switch garage door openers
(Canada)
15 = 8 DIP switch garage door openers
19 = 7 DIP switch garage door openers
(Write opener ID here: __ __)
3. The first DIP switch must be set to the -
position on your remote and opener.
Record your DIP switch sequence for
remaining DIP switches. If the DIP switch
is in the + position place a 1, 0
position place a 2, - position place a 3
in the corresponding box in the chart
below: NOTE: Leave any unused switch
locations blank.
DIP Switch
Sequence
TYPE 2
1. Select and write a 4-digit PIN:
__ __ __ __
2. Determine your opener ID using the list
below.
ID
DIP Switch Type
13 = 12 DIP switch Genie garage door
openers
14 = 10 DIP switch Linear garage door
openers
16 = 10 DIP switch Stanley garage door
openers
17 = 9 DIP switch Genie garage door
openers
18 = 8 DIP switch Linear, Moore-OMatic garage door openers
(Write opener ID here: __ __)
3. Record your DIP switch sequence. If
DIP switch is in the on or up position
place a 1, off or down position place
a 2 in the corresponding box in the chart
below: NOTE: Leave any unused switch
locations blank.
9
DIP Switch
1 2 3 4 5 6 7 8 9 10 11 12
Sequence
+
0
-
ON
3
OFF
DIP Switch
1
Sequence
+
0
-
TYPE 4
1. Select and write a 4-digit PIN:
__ __ __ __
2. Determine your opener ID using the list
below.
ID Garage door opener brand and
manufacturing dates
1 = Linear garage door openers
manufactured from 1997 to present.
2 = Chamberlain, Sears Craftsman,
LiftMaster, Master Mechanic and
Do It garage door openers
manufactured from 1997 to 2004
[Orange/Red Button].
3 = Chamberlain, Sears Craftsman,
LiftMaster, Master Mechanic and Do
It garage door openers
manufactured from 2005 to present
[Purple Button].
4 = Chamberlain, Sears Craftsman,
LiftMaster, Master Mechanic and Do
It garage door openers
manufactured from 1993 to 1996
[Green Button].
5 = Genie Intellicode and Overhead
Door garage door openers
manufactured from 2005 to present
(315 MHz).
6 = Genie Intellicode and Overhead
Door garage door openers
manufactured from 1995 to present
(390 MHz).
7 = Stanley garage door openers
manufactured in 1998 to present.
8 = Chamberlain, Sears Craftsman, and
LiftMaster garage door openers
manufactured 2011 to present
[Yellow Button].
9 = Wayne Dalton garage door openers
manufactured in 1999 to present.
(Write opener ID here: __)
3. Press * and # keys together until keypad
stops flashing.
4. Enter PIN from step 1, press #.
5. Enter ID from step 2, press #.
6. Press and release the Smart/Learn button
on garage door opener.
7. Enter your 4 digit PIN and press the 0
key.NOTE: For Genie and Overhead Door
units, press 0 twice.
8. To test and use, wait until light turns off,
enter your PIN and press the 0 key.
If opener does not function, repeat
programming.
BATTERY
Install out of the reach of children at a minimum height of 5 feet (1.5 m). Secure keypad to a
smooth surface. Mount the keypad out of the path of the moving garage door, but within sight of it
(4" clearance is needed for the cover).
1. Remove cover.
2. Remove battery cover to expose mounting holes.
3. Remove battery and mount keypad using screws provided.
4. Reassemble.
114A3484E
TYPE 3
1. Select and write a 4-digit PIN:
__ __ __ __
2. Your opener ID is 11.
11
3. Record your DIP switch sequence. Set
your first DIP switch to -, your first
DIP switch must be set to the - position
on your remote and opener. If the
DIP switch is in the + position place a
1, 0 position place a 2, - position
place a 3 in the corresponding box in the
chart below: NOTE: Leave any unused
switch locations blank.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
CLICKER
ADVERTENCIA
MODELO KLIK2U
ALTO
Lea completamente es instrucciones ANTES de empezar. Empiece con la puerta del garaje
cerrada. Identifique el tipo de abridor de puerta de garaje botn Smart/Learn o interruptor
DIP. El botn Smart/Learn o los interruptores DIP estn ubicados en la unidad del motor o
receptor externo. Consulte el manual del propietario si es necesario.
Los productos de Clicker son pensados ser utilizados slo con abre-puertas de garaje
fabric despus de 1993 que utiliza sensores de seguridad de foto. Estos siempre son
situados en/o cerca del parte inferior de riel de la puerta. Si su puerta de garaje no tiene
estos sensores conectado y trabajar, el abre-puerta no es sumiso con normas de
seguridad federales actuales y debe ser reemplazado.
Para impedir posibles LESIONES GRAVES o MORTALES debido al movimiento de una compuerta o puerta
de garaje:
Mantenga SIEMPRE los controles remotos fuera del alcance de los nios. No permita NUNCA a nios
que las operen ni que jueguen con los transmisores de control remoto.
Active la compuerta o la puerta SLO cuando la pueda ver claramente, est bien ajustada y no haya
obstrucciones en el recorrido de la puerta.
Mantenga SIEMPRE la compuerta o la puerta del garaje a la vista hasta que est completamente cerrada.
No deje NUNCA que nadie cruce la trayectoria de la compuerta o puerta en movimiento.
ADV
PRECAU
TIPO 1
Abridor de puerta de garaje o receptores de
Chamberlain, Sears Craftsman, LiftMaster,
Master Mechanic y Do It con: Interruptores
DIP de 3 posiciones.
Abridor
TIPO 4
ADVERTENCIA
Abridor de puerta de garaje o receptores de
TIPO 3
Abridor de puerta de garaje o receptores de
Chamberlain, Sears Craftsman, LiftMaster, Master
Mechanic y Do It con: Botones de SMART/
LEARN amarillo, blanco o gris.
Abridor
Abridor
ON
Control Remoto
Control Remoto
Control Remoto
ON
PROGRAMACIN:
TIPO 1
1. Seleccione y escriba un NIP de 4 dgitos:
__ __ __ __
2. Indentifique su numbero de Identificacin (ID)
usando el lista abajo.
ID
Tipo del interrupotores DIP
11 = Abridores de puerta de garaje con
interruptores DIP (E.U.)
12 = Abridores de puerta de garaje con 9
interruptores DIP (Canad)
15 = Abridores de puerta de garaje con 8
interruptores DIP
19 = Abridores de puerta de garaje con 7
interruptores DIP
(Escriba el ID del abridor aqui: __ __)
3. El interruptor primero debe ser al el posicin
- en su control remoto y abridor. Escriba el
secesin de los interruptores por los
interruptores que restante. Si el interruptor
est en la posicin + introduzca un 1, para la
posicin 0 un 2, para la posicin - un 3 en
la casilla correspondiente en la siguiente
grfica: NOTA: Deje cualquier espacio en
blanco inusitado de las localizaciones del
interruptor.
Secesin de
interruptores
NIP
+
0
-
TIPO 2
ON
(encendido)
OFF
(apagado)
+
0
-
TIPO 3
1. Seleccione y escriba un NIP de 4 dgitos:
__ __ __ __
2. Indentifique su numbero de Identificacin (ID)
usando el lista abajo.
ID
Marca de abridor de puerta de garaje y
fecha de fbrica
1 = Abridores de puerta de garaje de Linear
fbrica desde 1997 al presente.
2 = Abridores de puerta de garaje de
Chamberlain, Sears Craftsman,
LiftMaster, Master Mechanic y
Do It fbrica desde 1997 al 2004
[Botn anaranjado/rojo].
3 = Abridores de puerta de garaje de
Chamberlain, Sears Craftsman,
LiftMaster, Master Mechanic y
Do It fbrica desde 2005 al presente
[Botn morado].
4 = Abridores de puerta de garaje de
Chamberlain, Sears Craftsman,
LiftMaster, Master Mechanic y
Do It fbrica desde 1993 al 1996
[Botn verde].
5 = Abridores de puerta de garaje de Genie
Intellicode y Overhead Door fbrica
desde 2005 al presente (315 MHz).
6 = Abridores de puerta de garaje de Genie
Intellicode y Overhead Door fbrica
desde 1995 al presente (390 MHz).
7 = Abridores de puerta de garaje de Stanley
fbrica desde 1998 al presente.
8 = Abridores de puerta de garaje de
Chamberlain, Sears Craftsman, y
LiftMaster fbrica desde 2011 al
presente [Botn amarillo].
9 = Abridores de puerta de garaje de Wayne
Dalton fbrica desde 1999 al presente.
(Escriba el ID del abridor aqui: __ __)
3. Presione * y # simultneamente hasta que el
control inalmbrico deje de parpadear.
4. Introduzca el NIP de paso 1, presione #.
5. Introduzca el ID de paso 2, presione #.
6. Presione y suelte el botn de Smart/Learn en
el abridor de puerta de garaje.
7. Introduzca su NIP de 4 digitos y presione el
botn 0. NOTA: Pesione el botn 0 dos
veces para unidades de Genie y Overhead
Door.
8. Para realizar una prueba y usar, introduzca su
NIP nuevo y presione el boton 0.
Si el abridor no activo, repetir programmacin.
ADVER
PILA
Debe Instale 1.5 m (5 pies) del piso, fuera del alcanze de los nios. Fije el control inalmbrico al una
superficie plana. Instale el control inalmbrico alejado de las partes mviles de la puerta, pero an la vista de
la puerta
(la separacin del 10 cm (4 pulg.) es necesaria para la cubierta).
1. Quite cubierta.
2. Quite cubierta de la pila para ver las orificios de installacin.
3. Quite la pila y instale el control inalmbrico con los tornillos suministrados.
4. Vuelva a montar.
ADVERTENCIA
Para evitar la posibilidad de LESIONES GRAVES o INCLUSO LA MUERTE:
NUNCA permita que los nios pequeos estn cerca de las bateras.
Si alguien se traga una batera, llame al mdico de inmediato.
ADVE
PRECAUC
114A3484E
TIPO 3
1. Seleccione y escriba un NIP de 4 dgitos:
__ __ __ __
2. El ID de su abridor es 11.
11
AVISO: Para cumplir con las reglas de la FCC y/o de Canad (IC), ajustes o modificaciones de este receptor y/o transmisor estn
prohibidos, excepto por el cambio de la graduacin del cdigo o el reemplazo de la pila. NO HAY OTRAS PIEZAS REPARABLES DEL
USUARIO.
Se ha probado para cumplir con las normas de la FCC para USO DEL HOGAR O DE LA OFICINA. La operacin est sujeta a las dos
condiciones siguientes:(1) este dispositivo no puede causar interferencia perjudicial, y (2) este dispositivo debe aceptar cualquier
interferencia recibida, incluyendo la interferencia que puede causar una operacin no deseable.
ADVERTENCIA