Академический Документы
Профессиональный Документы
Культура Документы
If the above condition is not satisfied, a UE will move from GSM to UMTS and immediately start monito
Furthermore frequent re-selections between UMTS and GSM can cause mobile terminating call failure
In case of poor 3G coverage and low call setup success rate you can check the parameter SSearchRAT
Also the cell offsets for the GSM cells can be adapted to prefer call setup on the 2G layer.
# An HS-SCCH carries the information about the downlink HS-PDSCH allocated for each UE.
HS-DSCH
# HS-DSCHs are used to carry downlink user data
# Spreading factor of each HS-DSCH is fixed to 16
HS-SCCH
HS-DPCCH
# HS-DPCCHs are uplink dedicated hannels
# The spreading factor is 256
1) If the setup of an HSPA+-enabled cell is supported, the BTS establishes downlink channels in terms
2) After an HSPA service is established, the UE continually measures the signal quality in the radio env
reports the CQI to the BTS through uplink HS-DPCCHs.
3) The UE continually monitors the downlink HS-SCCHs to check whether the data is sent to the UE.
4) After receiving the CQI, the BTS determines whether to send the data to the UE according to the CQ
# As you know HSDPA supports max of 21.1 mbps in case of 64 QAM support so at the same you shou
# Should have at least 11 E1(2*11=22 Mbps) so that throughput will not degrade due to transmission
# A typical handover process is: measurement control --> measurement report --> handover deci
UE, measured cells are divided into the following three types:
1) Active set cells: Cells in an active set communicate with the UE simultaneously.
2) Monitored set cells: Among the cells included in the adjacent cell list delivered by the RNC, som
3) Detected set cell: Detected set cells refer to those cells detected by the UE itself, rather than the
Intra-Frequency Measurement
# In this example, the cells where P CPICH 1, P CPICH 2 and P CPICH 3 are belong to an active set, wh
# This event is used to replace the poor cells in the active set, if the number of cells in the active set
4) Event 1D: The best cell changes
Measurement
quantity
P CPICH 1
P CPICH 2
Measurement
quantity
P CPICH 1
P CPICH 2
P CPICH3
Time
Reporting
event 1D
In order to prevent frequent triggering of event 1D due to signal fluctuations, , we can use the hystere
Measurement
quantity
P CCPCH 1
Hysteresis
P CCPCH 2
Hysteresis
Reporting
event 1D
Time
As we can see, as the hysteresis condition is not met at the second time, event 1D reporting is not trig
Hysteresis Related to Soft Handover
5) Event 1E: The measurement value of a primary pilot channel exceeds the absolute threshold
Measurement
quantity
P CPICH 1
P CPICH 2
Absolute
threshold
P CPICH 3
Reporting
Time
P CPICH 2
Absolute
threshold
P CPICH 3
Reporting
event 1E
Time
Event 1E can be used to trigger the measurement reports of cells including those detected by the UE
6) Event 1F: The measurement value of a primary pilot channel is lower than the absolute threshold
Measurement
quantity
P CPICH 1
P CPICH 2
Absolute
threshold
P CPICH 3
Reporting
event 1F
Time
RRC Setup
Counter
RRC.FailConnEstab.Cong
VS.RRC.FailConnEstab
Sub Counter
VS.RRC.Rej.Power.Cong
VS.RRC.Rej.UL.CE.Cong
VS.RRC.Rej.DL.CE.Cong
VS.RRC.Rej.Code.Cong
VS.RRC.Rej.ULIUBBandCong
VS.RRC.Rej.DLIUBBandCong
VS.RRC.Rej.RL.Fail
RRC.FailConnEstab.Cong
VS.RRC.Rej.AAL2.Fail
RRC.FailConnEstab.NoReply
CS RAB Setup
Counter Level1
VS.RAB.FailEstabCS.RNL
VS.RAB.FailEstCS.RIPFail
VS.RAB.FailEstCS.Relo
VS.RAB.FailEstabCS.RNL.Other
VS.RAB.FailEstabCS.TNL
VS.RAB.FailEstabCS.other.CELL
PS RAB Setup
Counter Level1
VS.RAB.FailEstPS.RNL
VS.RAB.FailEstPS.RIPFail
VS.RAB.FailEstPS.Par
VS.RAB.FailEstPS.Relo
VS.RAB.FlEstPS.RNL.Other
VS.RAB.FailEstPS.TNL
VS.RAB.FailEstPS.NResAvail
VS.RAB.FailEstabPS.Other.Cell
CS Call Drop
Counter Level1
VS.RAB.Loss.CS.RF
VS.RAB.Loss.CS.Abnorm
VS.RAB.RelReqCS.OM
VS.RAB.RelReqCS.UTRANgen
VS.RAB.RelReqCS.RABPreempt
VS.RAB.Loss.CS.Aal2Loss
VS.RAB.Loss.CS.Congstion.CELL
VS.Call.Drop.CS.Other
PS Call Drop
Counter Level1
VS.RAB.Loss.PS.Abnorm
VS.RAB.Loss.PS.RF
VS.IRATHO.FailCSOut.RNC
Sub CounterLevel3
VS.RAB.FailEstabCS.Cong
Sub CounterLevel4
VS.RAB.FailEstCs.Power.Cong
VS.RAB.FailEstCs.Code.Cong
VS.RAB.FailEstab.CS.DLIUBBand.Cong
VS.RAB.FailEstab.CS.ULIUBBand.Cong
VS.RAB.FailEstCs.ULCE.Cong
VS.RAB.FailEstCs.DLCE.Cong
VS.RAB.FailEstabCS.Unsp.Other
VS.RAB.Loss.PS.SRBReset
VS.RAB.Loss.PS.TRBReset
Strategy
IdleQoffset
# The larger the value of the parameter, the lower the probability of selecting neighboring cells.
# The smaller the value the parameter, the higher the probability of doing so.
# IdleQoffset1sn : Offset of cell CPICH RSCP measurement value in cell selection or reselection when t
# IdleQoffset2sn : Offset of cell CPICH Ec/No measurement value in cell selection or reselection when
BlindHO
F2 Script
F1 Script