Академический Документы
Профессиональный Документы
Культура Документы
1 June 2002
8100-0004-0001 Rev A
Disclosure Limitation: The information in this report includes proprietary and trade secret information subject to 5 U.S.C.
5.52(B) and 18 U.S.C. 1905. This report includes data that shall not be disclosed outside of iDirect, iDirects reseller and
partners and may only be duplicated, used, or disclosed in whole or in part for any purpose other than to fulfill iDirects
business objectives, yet subject to iDirects rights under 5 U.S.C 5.52(B)(4) and 18 U.S.C. 1905. This restriction does not limit
the Users right to use information contained in this report if it is obtained from another source without restriction. The data
subject to this restriction are contained on all sheets of this report and its attachments.
Copyright 2002, iDirect Inc. All rights reserved. This manual may not
be reproduced, in part or in whole, without the permission of iDirect Inc.
The specifications and information regarding the products in this Users
Guide are subject to change without notice. All statements, information,
and recommendations in this Users Guide are believed to be accurate but
are presented without warranty of any kind, express, or implied. Users
must take full responsibility for their application of any products.
Notwithstanding any other warranty herein, all document files and
software are provided as is with all faults. iDirect and resellers disclaim
all warranties expressed or implied, including, without limitation, those of
merchantability, fitness for a particular purpose and non infringement or
arising from a course of dealing, usage, or trade practice.
In no event shall iDirect or its supplier be liable for any indirect, special,
consequential, or incidental damages, including, without limitation, lost
profits or loss or damage to data arising out of the use or inability to use
this Users Guide, even if iDirect or its suppliers have been advised of the
possibility of such damages.
Trademarks, brand names and products mentioned in this guide are the
property of their respective owners. All such references are used strictly in
an editorial fashion with no intent to convey any affiliation with the name
or the products rightful owner.
8100-0004-0001 Rev A
Table of Contents
1
Preface...............................................................................................................................................................................................5
1.1
Objectives .................................................................................................................................................................................5
1.2
Audience ...................................................................................................................................................................................5
1.3
1.4
Warranty............................................................................................................................................................................................6
2.1
2.2
Disclaimer. ................................................................................................................................................................................7
3.2
Sales...........................................................................................................................................................................................8
3.3
4.2
4.3
Operational / Maintenance....................................................................................................................................................11
4.4
Service .....................................................................................................................................................................................12
Hardware Description.....................................................................................................................................................................13
5.1
Overview .................................................................................................................................................................................13
5.2
Physical Description...............................................................................................................................................................14
5.3
6.2
6.3
7.2
Mounting Configuration of the MUSiCTM Box ....................................................................................................................21
7.2.1
General Guidelines for IDU Desktop/Shelf Mounting....................................................................................................21
7.2.2
General Guidelines for Wall Mounting...........................................................................................................................21
7.2.3
General Guidelines for Flush Rack Mounting .................................................................................................................23
7.3
Connecting System AC Power ...............................................................................................................................................24
7.3.1
Checking Conditions Prior to Power Up ...........................................................................................................................25
7.3.2
Power Up the MUSiCTM Box ...........................................................................................................................................25
7.4
7.5
Maintenance....................................................................................................................................................................................28
8.1
8100-0004-0001 Rev A
9.1
RF Specification:....................................................................................................................................................................29
9.2
10 MHz Reference:.................................................................................................................................................................29
9.3
Power Specification................................................................................................................................................................31
9.4
9.5
10
10.2
10.3
Safety.......................................................................................................................................................................................36
10.4
NOM (Mexico)........................................................................................................................................................................36
10.5
11
11.2
Installation Warning..............................................................................................................................................................38
11.3
11.4
11.5
11.6
11.7
11.8
11.9
Acronyms.....................................................................................................................................................................................55
13
Glossary .......................................................................................................................................................................................58
14
Appendix......................................................................................................................................................................................63
14.1 Coaxial Cable Specification...................................................................................................................................................63
7.3.1
Terminating Coaxial Cable ..............................................................................................................................................64
14.2
14.3
8100-0004-0001 Rev A
1 Preface
1.1
Objectives
This iDirect MUSiCTM Box Users Guide, alias Users Guide, describes the initial hardware installation and
maintenance procedures for the iDirect MUSiCTM Box, alias MUSiC Box.
1.2 Audience
To use this Users Guide, you should be familiar with the iDirect MUSiCTM Box, cabling and wiring
practices and preferably have experience as an electronic or electromechanical technician. This Users
Guide is intended for use by the VSAT equipment installer, System Engineers, and operator responsible for
maintaining the iDirect Network. Only qualified service personnel should install and operate iDirect
MUSiCTM Box.
Updates to this Users Guide are published often. Contact your Reseller or iDirect Sales Representative for
the latest version.
1.3
Related Documentation
8100-0007-0001
8100-0003-0001
8100-0005-0001
Due to the complexity of network configuration procedures, they are beyond the scope of this
publication. However, additional network configuration documentation can be found in the following
publications:
1.4
iDirect Network Management System (NMS) Training Guide. This document contains
procedures and sample configurations for configuring the NMS Server.
iBuilder Users Guide. This document contains procedures and sample configurations for
configuring/building an operational network.
iMonitor Users Guide. This document contains procedures and sample configurations to
monitor the operation of the network.
Documentation Feedback
iDirect Inc. has made every effort to ensure the correctness and completeness of the material in this Users
Guide. If there is any clarification, correction of error, typo, and the like, please send your
comment/feedback to:
iDirect, Inc.
Attn: Documentation Department
13865 Sunrise Valley Drive
Herndon, VA 20171
Email: Docs@iDirect.net
Note: The specifications and information regarding the products in this Users Guide are subject to change
without notice. All statements, information, and recommendations in this Users Guide are believed to be
accurate but are presented without warranty of any kind, express, or implied. Users must take full responsibility
for their application of any products.
8100-0004-0001 Rev A
2 Warranty
2.1
8100-0004-0001 Rev A
2.2
Disclaimer.
iDIRECT DOES NOT WARRANT THAT USE OF THE MUSiCTM Box WILL BE UNINTERRUPTED
OR ERROR FREE OR AS TO THE RESULTS THAT MAY BE OBTAINED FROM USE OF THE
NETMODEM SOLUTION, INCLUDING WITHOUT LIMITATION DATA TRANSFER RATES OR
OVER SUBSCRIPTION LEVELS THAT MAY BE ACHIEVED. EXCEPT AS EXPRESSLY STATED
HEREIN, EACH PARTY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, IMPLIED WARRANTIES OF TITLE, MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, NONINFRINGEMENT, ACCURACY, INTEGRATION, AND
ALL IMPLIED WARRANTIES ARISING OUT OF USAGE OF TRADE, COURSE OF DEALING
OR COURSE OF PERFORMANCE.
Your specific Reseller Agreement contract may differ from this Warranty
or Disclaimer, in that event, your Reseller Agreement Contract shall
supersede this Warranty and Disclaimer.
8100-0004-0001 Rev A
3 Technical Support
Contact your local service representative, reseller, or your service provider per your contract if further
information is needed beyond the coverage of this Users Guide.
3.2
3.3
(703) 648-8151
(703) 648-8190
NOC@idirect.net
Telephone:
Email:
(703) 648-8000
sales@idirect.net
Sales
8100-0004-0001 Rev A
Safety Instructions
Use the following safety guidelines to help protect the iDirect MUSiCTM Box from potential damage and to
help ensure your own personal safety.
For your safety and protection, read this entire Users Guide before you attempt to install or use your iDirect
MUSiCTM Box. In particular, read this safety section carefully. Keep this safety information where you can
refer to it if necessary.
Heed Warnings All warnings on the product and in the operating instructions should be adhered to.
Follow Instructions All operating and use instructions should be followed.
Section 11 contains all translated Warnings and Danger in many common languages that are used in
this Users Guide.
4.1
Safety Definitions
The following symbols are used throughout this Guide to alert the user of possible danger or when to use
caution.
Symbol
Definition
WARNING OR CAUTION:
8100-0004-0001 Rev A
4.2
MUSiCTM
Box Installation
When installing your iDirect MUSiCTM Box, observe the following safety guidelines.
Ventilation
Slots and openings on the chassis are provided for ventilation and to
ensure reliable operation of the product. To protect the chassis from
overheating, these openings must NOT be blocked or covered at all
times. This product should not be placed in a built-in installation such as
a bookcase or enclosed rack unless proper ventilation is provided or
the manufacturers instructions have been adhered to.
AC Polarization This product is equipped with a plug that will fit into the power outlet
only one way. Do not modify the plug by defeating this feature. If the
plug does not fit, contact your electrician to replace your outlet. To
prevent electric shock or impair performance, do not use this plug with
an extension cord or outlet unless you can fully insert the blades without
blade exposure.
Power Sources
Operate this product only from the type of power source indicated on
the rear of the chassis next to the power receptacle (100-240VAC
50/60Hz). If you are not sure of the type of power supply at your site,
consult your teleport operator or local power company.
Power Cord Protection Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them; pay
particular attention to cords at plugs, convenience receptacles, and at the
point where they exit the product.
Overloading
Electrical Safety For electrical safety, power line operated equipment accessories connected
to this unit should bear the UL, NRTL, CE listing mark and should not
be modified so as to defeat the safety features. This will help avoid any
potential hazard from electrical shock or fire. If in doubt, contact
qualified service personnel.
Water and Moisture To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture.
Lightning
For added protection for this product during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it from
the wall outlet, disconnect the antenna and cable system. This will
prevent damage to the product due to lightning and power-line surges.
Water and Moisture To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture.
iDirect MUSiC Box Installation and Users Guide
10
8100-0004-0001 Rev A
Heat
The product should be situated away from heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers) that
produce heat.
Accessories
Attachments
!
4.3
Operational / Maintenance
As you use your iDirect MUSiCTM Box, observe the following safety guidelines:
Cables
Ventilation
Slots and openings on the chassis are provided for ventilation and to
ensure reliable operation of the product. To protect it from overheating,
these openings must not be blocked or covered. If there is any dust
build up on the vent openings of the MUSiCTM Box, vacuuming is
recommended to remove these particulate to ensure proper airflow.
Cleaning
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
wiping up dust or use a vacuum cleaner to remove dust.
!
!
Object and Liquid Entry Never push objects of any kind into the iDirect MUSiCTM Box
through any openings as they may touch dangerous voltages or short
out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the MUSiCTM Box.
11
8100-0004-0001 Rev A
4.4
Service
When your iDirect MUSiCTM Box requires service, observe the following safety guidelines:
Servicing Do not attempt to service the iDirect MUSiCTM Box internal assemblies yourself
as opening and removing covers may expose you to dangerous voltages or other
hazards. There are no user serviceable parts inside. Opening the units will void the
warranty. Refer all servicing to qualified service personnel.
Conditions Requiring Service Unplug the iDirect MUSiCTM Box from the AC Power
outlet and refer servicing to qualified service personnel under the following
conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled on, or objects have fallen into, the iDirect
MUSiCTM Box or it has been exposed to water.
c. If the iDirect MUSiCTM Box does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the
operating instructions. Other adjustments may result in damage and will
often require extensive work by a qualified technician to restore the iDirect
MUSiCTM Box to its normal operation.
d. If the iDirect MUSiCTM Box has been dropped or if the chassis has been
damaged.
e. When the iDirect MUSiCTM Box exhibits a distinct change in performance.
12
8100-0004-0001 Rev A
5 Hardware Description
5.1
Overview
The iDirect MUSiCTM Box provides a way to link multiple tenants/users of NetModem II or NetModem II
Plus at a site to a single antenna/ODU. The unique features of iDirect MUSiCTM are
built in summer/splitter with integrated line amplifiers to enable multiple IDU on the same
network to share a single antenna/ODU.
NetModem
#1
NetModem
#2
NetModem
#3
NetModem
#4
MUSiC
Box
. . . . . . . . . . . . . . .
Rx
ODU
Tx
NetModem
#8
The iDirect MUSiCTM Box should only be use in an indoor environment. The MUSiCTM Box can be use on
table top, wall mount or optional rack mount with 2U opening. The MUSiCTM Box requires less power and
generates minimal heat (typical power consumption of 4W for the MUSiCTM Box).
iDirect MUSiC Box Installation and Users Guide
13
8100-0004-0001 Rev A
5.2
Physical Description
The iDirect MUSiCTM Box chassis consist of 2 major components:
MUSiCTM Box
MUSiCTM Box with Optional Rack Mount Tray (Front and Rear View)
14
8100-0004-0001 Rev A
Tx
IDU
Tx
Mon
5A
LED Indicator:
Green - DC Power to BUC
Red - No DC Power to BUC
Tx
IFL
Rx
Gain
Rx
IFL
BUC
PWR
Tx
Gain
+24V
Rx
IDU
Gain Setting
Rotary Switch
To Rx Port of NetModem(s)
Normal Operation: No DC or 10MHz
Connect to Recommended
External +24VDC, 5 amp
Description
Kycon
KPJ-4S-S
Red Color
Green Color
F Type Female
15 step Rotary
Switch
F Type Female
15 step Rotary
Switch
F Type Female
F Type Female
F Type Female
Purpose
+24VDC External Power Supply input
No DC power to BUC
DC power to BUC
Monitor port; aggregate of all IDUs Tx
-19 dB typical coupling.
Tx gain adjust 1-31 dB in 2 dB step
Aggregate Transmit signal to Block
UpConverter (BUC)
Tx gain adjust 0-15 dB in 1 dB step
Receive signal from LNB Output
Transmit signal from IDU to MUSiCTM Box
Receive signal from MUSiCTM Box to IDU
15
8100-0004-0001 Rev A
5.3
Qty
1
2
3
4
1
1
1
1
Description
iDirect MUSiC Box
TM
iDirect P/N
9130-0006-0001
2100-0004-0003
8100-0004-0001
4118-0001-0xxx
16
8100-0004-0001 Rev A
6.2
Safety Recommendation
When installing the iDirect MUSiCTM Box Solution, observe all caution and warning statements.
The following guidelines will help ensure your safety and protect the equipment. However, these
guidelines may not cover all potentially hazardous situations you may encounter during the
installation.
The installation of the iDirect MUSiCTM Box Solution should comply with the national and
local electrical codes:
o In the United States, the National Fire Protection Association (NFPA) 70, United
States National Electric Code.
o In Canada, the Canadian Electric Code, Part 1, CC22.1
o In other countries, the International Electromechanical Commission (IEC)
Recommendation 364, part 1 through part 7.
Review the safety warnings listed in Regulatory Compliance and Safety Information for the
iDirect MUSiCTM Box Solution before installing, configuring, or performing maintenance on
the system.
Always disconnect all power connections before installing or removing a chassis.
Keep the staging area clear and free of dust during and after installation.
Keep tools, MUSiCTM Box components, and shipping boxes away from walk area.
The iDirect MUSiCTM Box Solution operates safely when it is used in accordance with its
marked electrical ratings and product usage instructions.
Only Trained and qualified personnel should be allowed to install or replace this
equipment.
This Unit is intended for installation in restricted access areas. A restricted access
area is where access can only be gained by service personnel through the use of a
special tool, lock and key, or other means of security, and is controlled by the
authority responsible for the location.
17
8100-0004-0001 Rev A
Caution: Do not use any other power supply than what is recommended.
Follow these basic guidelines when you are working with any electrical equipment.
Disconnect all power and external cables before installing or removing the chassis
Do not work alone when potentially hazardous conditions exist.
Never assume that power has been disconnected; always check.
Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe. Never install equipment that appears damaged.
Carefully examine your work area for possible hazards such as wet floor, ungrounded
power extension cables, and missing safety grounds.
Warning: Do not work on the system or connect or disconnect cables during
periods of lightning activity.
Read the installation instructions before you connect the system to its
power source.
Handle the IDU by the metal enclosure only ; never touch the connector pins.
Avoid contact between the connector pins and clothing. ESD voltages on clothing can
still cause damage.
18
8100-0004-0001 Rev A
6.3
Inspect all shipping containers. If any damage or other signs of mishandling are evident,
inform both the carrier and iDirect/or the reseller.
Make sure the boxes are facing upward (refer to the box orientation arrows on the
shipping container). Remove the tapes and any exterior covering from the boxs lid.
Remove items from the box only when needed.
Note:
You may want to save the MUSiCTM Box shipping boxes after you have
unpacked the system. You will need these boxes if you want to move or
ship the system in the future.
Note:
19
8100-0004-0001 Rev A
Quantity
1
1
1
1
Description
Comments
F-Connector Crimper
You might need additional tools and equipment to install associated equipment and cables. You might
also require test equipment to check signal, power levels, and communication links.
20
8100-0004-0001 Rev A
7.2
When installing the iDirect MUSiCTM Box, you should follow the following guidelines:
Check the site location for factors such as accessibility, power, signal, and network cable
connections and future expansion.
Plan for access to both front and rear of the MUSiCTM Box.
Ensure the room where the iDirect MUSiCTM Box operates has adequate ventilation. Ambient air
temperature may not cool the MUSiCTM Box to acceptable operating temperatures without
adequate ventilation.
If the MUSiCTM Box is mounted in an enclosed shelf, ensure that the shelf has adequate ventilation.
An enclosed shelf should have air opening on sides and top to provide natural convection air
movement.
Do not install the MUSiCTM Box on the floor and away from any area that tends to collect dust.
Warning: Install the MUSiCTM Box chassis in a location where access is unobstructed. In
addition, the louvered openings of the enclosure must not be blocked. Any
obstruction to the louvered openings will disturb the natural convection
cooling. Failure to do so will result in performance degradation or damage.
When installing the iDirect MUSiCTM Box on the wall, you should follow the following guidelines:
Check the site location for factors such as accessibility, power, signal, and network cable
connections and future expansion.
Plan for access to both front and rear of the MUSiCTM Box
The MUSiCTM Box is designed to wall mount in only two configurations i.e. the rear connectors are
pointing toward the right hand side or the left hand side.
Ensure the room where the MUSiCTM Box operates has adequate ventilation. Ambient air
temperature may not cool the MUSiCTM Box to acceptable operating temperatures without
adequate ventilation.
Do not wall mount the MUSiCTM Box above a heat register/radiator.
Warning: Install the chassis on the wall where access to the MUSiCTM Box is
unobstructed. Any obstruction to the louvered openings will disturb the
21
8100-0004-0001 Rev A
Step 5: Install the screws such that the contact surface of the pan head screw should be about 0.4
inch (1 cm) from the wall.
Step 6: Overlay the IDU wall mount feature holes of the chassis over the pan head screws. Once
lined up, slide down the chassis downward to hang the IDU on the pan head screws.
Mounting Wall
(Drywall, Plywood,
or comparable)
Mounting Wall
(Drywall, Plywood,
or comparable)
5.4 inch
(13.7 cm)
9.6 inch
(23.4 cm)
2.7 inch
(6.85 cm)
9.6 inch
(23.4 cm)
2.7 inch
(6.85 cm)
5.4 inch
(13.7 cm)
0.4 inch
(1 cm)
Plywood or
Drywall
22
8100-0004-0001 Rev A
The iDirect MUSiCTM Box can only be flush-mounted in the 19 inch rack using the optional Rack
Mounting Tray kit. The MUSiCTM Box can be mounted with either the front or the rear of the chassis
panel facing outward toward the aisle.
When installing the iDirect MUSiCTM Box in the rack, you should follow the following guidelines:
The iDirect MUSiCTM Box Rack Mounting Tray requires a minimum of 2 rack units (3.5 inches
or 8.9 cm) of vertical rack spaces. You should measure the proposed rack location before
mounting the chassis.
Check the site location for factors such as accessibility, power, signal, and network cable
connections and future expansion.
Plan for access to both front and rear of the MUSiCTM Box
Ensure the room where the MUSiCTM Box operates has adequate ventilation. Ambient air
temperature may not cool the MUSiCTM Box to acceptable operating temperatures without
adequate ventilation.
If the MUSiCTM Box is mounted in an enclosed rack, ensure that the rack has adequate ventilation.
An enclosed rack should have louvered sides and top with fans to provide cooling air.
Do not install the MUSiCTM Box on the floor and out of any area that tends to collect dust.
Before using a particular rack, check for obstructions (such as power strip) that could impair rackmount installation
Warning: Install the chassis in the rack where access to the plug-ins are unobstructed.
In addition, the fan air intake or exhaust must not be obstructed at all times.
Failure to do so will result in performance degradation or damage.
Warning: To Prevent bodily injury when mounting or servicing the iDirect MUSiCTM
Box Chassis in a rack, you must take special precautions to ensure that
the rack(s) remains mechanically stable. The equipment rack must be
solidly secured to the foundation/computer floor and/or secured to the
adjacent racks.
Step for Mounting iDirect MUSiCTM Box in the rack
Step 1: Using number 2 Phillip screwdriver,
remove and save the 5 pan head
screws as shown.
23
8100-0004-0001 Rev A
Step 2: Position the front panel of the MUSiCTM Box into the opening of the Rack Mounting Tray.
Carefully slide the IDU into
position of the tray as shown.
Re-install the 5 pan head screws
that were removed.
7.3
Note: - If power is required to be remove from the chassis, you should disconnect power
from the AC power cord. Never disconnect the power to the MUSiCTM Box with the
DC output power cord of the External Power Supply.
24
8100-0004-0001 Rev A
No RF coax cable is connected to the Tx, Rx, or the Monitor Ports on the rear of chassis.
Definition
No DC voltage on TX IFL Port
DC voltage on TX IFL Port
Note: If the LED is off, this indicates a malfunction of the MUSiCTM Box .
Step 3: Disconnect the AC power cord.
7.4
Enable
Internal
DIP Switch
(on MUSiC PCB)
2
3
4
Disable =
Disable =
Disable =
Enable =
BUC DC On. It will be overide with Enable (BUC DC Off) if there is DC on any of Tx IFL Port.
BUC 10MHz On
LNB DC On
LNB 10MHz Off
However, if you need to change factory default settings, follow the following steps:
iDirect MUSiC Box Installation and Users Guide
25
8100-0004-0001 Rev A
Disable
Switch Definition:
Switch # 1 :
Switch # 2 :
Switch # 3 :
Switch # 4 :
Enable
BUC DC Off
BUC 10MHz Off
LNB DC Off
LNB 10MHz Off
Internal
DIP Switch
(on MUSiC PCB)
1
2
3
4
7.5
Tx
IDU
Tx
Mon
5A
LED Indicator:
Green - DC Power to BUC
Red - No DC Power to BUC
Tx
IFL
Rx
Gain
Rx
IFL
BUC
PWR
Tx
Gain
+24V
Gain Setting
Rotary Switch
Rx
IDU
To Rx Port of NetModem(s)
Normal Operation: No DC or 10MHz
Connect to Recommended
External +24VDC, 5 amp
26
8100-0004-0001 Rev A
Step 2: Make sure the BUC 10MHz and BUC DC power are disable from each respective IDUs. If
BUC DC voltage is enable from one of the IDU, the MUSiCTM Box will shut off the DC
voltage to the BUC.
Step 3: Depending on the IFL lengths, set the Tx power from each IDU such that the nominal RF
input power to the MUSiCTM Box is between -20 to -14 dBm.
Note: Under no circumstances should the RF input power to the MUSiCTM Box
exceed -9dBm.
Step 4: Connect the spectrum analyzer (if available) to the Tx Mon port.
Step 5: Depending upon the IFL length between the MUSiCTM Box and the ODU, you may need to
adjust the TX Gain and RX Gain rotary switches to set the proper RF levels.
Max Gain
For Max Gain, set the arrow on rotary switch to the left
tick mark as shown
To reduce gain (increase attenuation) from max gain, rotate
switch clockwise. There are 16 rotary steps to give 1 to 31 dB of
gain adjustment in 2 dB step for Tx Gain adjustment and 0 to 15 dB
of gain adjustment in 1 dB step for Rx Gain adjustment.
Note: when the switch is rotated 360 degrees, the gain will jump from min gain to max gain
(i.e. 15 dB attenuation to 0 dB attenuation for Rx Gain adjustment and 31 dB
attenuation to 1 dB attenuation for Tx Gain adjustment).
Shown below is a typical setup (each installation will be different due to specific configuration
and various IFL lengths):
A. Set Tx Rotary Gain Switch to Max Gain if IFL loss between MUSiC Box and BUC is
more than 20 dB. If IFL loss is less that 5 dB, then set rotary switch to min gain (max
attenuation). If the IFL loss is between 5 and 20 dB, then set gain accordingly using
the rotary switch with its 15 dB of range for optimum performance.
B. The operational input power in to the MUSiC box should not exceed -9 dBm (output
distortion will occur If -9 dBm is violated). If there is minimum IFL loss between the
NetModem and MUSiC box, then adjust NetModem Tx output power such that -9
dBm into the MUSiC Box is not violated.
C. The max IFL loss between NetModem and MUSiC box is 16 dB [7dBm - (-9dBm)].
The max IFL loss between MUSiC box and BUC is 29 dB [13dBm - (-16dBm)].
Hence, total IFL Loss is 45 dB with usage of MUSiC box:
45 dB --> 545 ft of RG-6
45 dB --> 865 ft of RG-11
iDirect MUSiC Box Installation and Users Guide
27
8100-0004-0001 Rev A
8 Maintenance
This Section describes basic maintenance for the iDirect MUSiCTM Box Chassis.
8.1 Dust Removal
Regular dusting/dust removal will ensure the iDirect MUSiCTM Box to operate within operational
specification.
Use a slightly damp cloth with excess moisture wringed out (not saturated, wet or dripping cloth) to
wipe away the dust that collects on the outside of the enclosure.
A high, dusty environment will require frequent maintenance of vacumming the dust off the
enclosure vents and circuit board.
28
8100-0004-0001 Rev A
9 System Specification
The iDirect MUSiC Box Chassis is in compliance with the following specifications.
9.1
RF Specification:
Frequency Range:
Transmit:
Receive:
950-1700 MHz
950-1700 MHz
RF Power Range:
Transmit Output:
Receive Input:
RF Power Adjustment Range:
Transmit Output:
Receive Input:
RF Power Adjustment Step Size:
Transmit:
Receive:
Discrete Spurs, harmonics and nonharmonics:
Maximum MUSiC Box Cascadable
10 MHz BUC and LNB Reference Output
Transmitter Spectral Shaping
9.2
10 MHz Reference:
Initial Frequency Accuracy (ppm)
Frequency Stability over Operational
Temperature (ppm)
Typical 10 MHz Reference Phase Noise
(dBc/Hz) at:
10 Hz
100 Hz
1 KHz
10 KHz
Aging per year (ppm)
Frequency Adjustment (ppm)
0.05
0.16
-87
-122
-142
-150
0.2
5
29
8100-0004-0001 Rev A
30
8100-0004-0001 Rev A
9.3
Power Specification
Input Voltage
PW122RA2400F02
PW122KA2400F02
100 240 V~ (VAC) Single Phase
Frequency:
50 60 Hz
Current Consumption:
at 90 VAC:
at 254 VAC:
Protection:
9.4
+24VDC
Tx Mon
Tx IFL
Rx IFL
Tx IDU (Port 1-8)
Rx IDU (Port 1-8)
31
8100-0004-0001 Rev A
9.5
Weight:
Heat Dissipation:
8W (27 BTU/Hour)
Airflow
Temperature:
Operational:
Storage:
32 to 113 F (0 to 45 C)
-30 to 176 F (-34 to 80 C)
Operational:
Storage:
0 to 90% non-condensing
5 to 93%
Relative Humidity:
Altitude:
Operating:
Storage:
Operational Vibration:
(10 minutes per axis)
Operational Shock:
32
8100-0004-0001 Rev A
The iDirect MUSiCTM Box Chassis complies with Class B of Part 15 of the FCC (Federal
Communications Commission) rules as is identified by use of the FCC logo.
Radiated and Conducted Emission
33
8100-0004-0001 Rev A
Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. The equipment generates, uses and can radiate
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the
equipment cause harmful interference to radio or television reception, it can be determined by
removing or applying power to the equipment to determine if the interference goes away or return
when the unit is on or off.
To meet FCC requirements, only peripherals (computer input/output devices, terminals, printers, etc.)
certified to comply with the Class B limits may be attached to this device. Operation with noncertified peripherals is likely to result in interference to radio and TV reception.
To meet FCC requirements, shielded cables are required to connect the device to a personal computer,
peripheral, or other Class B certified device.
Warning: Modification of this equipment without written authorization from iDirect Inc.
may result in this equipment no longer complying with FCC requirements for
Class B digital devices. In that event, your right to use the equipment may be
limited by FCC regulations, and you may be required to correct any
interference to radio or television communications at your own expense.
10.2 CE Compliance (European Union)
Marking by this symbol indicates the iDirect MUSiCTM Box Chassis is in compliance with all relevant
European Radio and Telecommunications Terminal Equipment (R&TTE) Directives. This Class 2
equipment has been registered with the European Notified Body 0682 (NB).
EMC Emission
EMC Immunity
EMC Radio Spectrum Matters
Health
34
8100-0004-0001 Rev A
10.3 Safety
TUV Rheinland of North America is a Nationally Recognized Testing Laboratory (NRTL) in the
United States and is accredited by the Standards Council of Canada to test and certify products to
Canadian National Standards. The iDirect MUSiCTM Box Chassis is compliance to both U.S. and
Canadian National Standards on Safety.
In addition, the IECEE CB Scheme Test Report and CB Test Certificate for the iDirect MUSiCTM
Box Chassis is done with TUV Rheinland of North America. This CB Scheme is recognized by the
multilateral agreement among participating countries and certification organizations. Since iDirect is
utilizing this CB test report issued by TUV, the iDirect MUSiCTM Box Chassis is in compliance with
all other member countries of the CB Scheme.
Safety
IEC60950: 1999
Marking by the NOM symbol indicates the iDirect MUSiCTM Box Chassis is compliance with NOM
(Normas Oficiales Mexicanas) standards of Mexico. TUV Rheinland of North America, Inc. has a
bilateral agreement with a Mexican laboratory accredited by Sistema Nacional de Acreditamiento de
Laboratorios de Pruebas (SINALP) to evaluate products against Mexican standards.
10.5 GOST-R Mark (Russia)
Marking by this symbol indicates the iDirect MUSiCTM Box Chassis is in compliance with Safety
Directives of Russia.
35
8100-0004-0001 Rev A
Warning This warning symbol means danger. You are in a situation that could cause bodily injury.
Before you work on any equipment, be aware of the hazards involved with electrical circuitry and
be familiar with standard practices for preventing accidents.
Waarschuwing
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel
kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van
de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard
maatregelen om ongelukken te voorkomen.
Varoitus
Attention
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
causer des blessures ou des dommages corporels. Avant de travailler sur un quipement, soyez
conscient des dangers poss par les circuits lectriques et familiarisez-vous avec les
procdures couramment utilises pour viter les accidents.
Warnung
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer
Krperverletzung fhren knnte. Bevor Sie mit der Arbeit an irgendeinem Gert beginnen,
seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der
Standardpraktiken zur Vermeidung von Unfllen bewut.
Avvertenza
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai
circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti.
Advarsel
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan fre til personskade.
Fr du utfrer arbeid p utstyr, m du vare oppmerksom p de faremomentene som elektriske
kretser innebrer, samt gjre deg kjent med vanlig praksis nr det gjelder unng ulykker.
Aviso
Este smbolo de aviso indica perigo. Encontra-se numa situao que lhe poder causar danos
fsicos. Antes de comear a trabalhar com qualquer equipamento, familiarize-se com os
perigos relacionados com circuitos elctricos, e com quaisquer prticas comuns que possam
prevenir possveis acidentes.
Advertencia!
Este smbolo de aviso significa peligro. Existe riesgo para su integridad fsica. Antes de
manipular cualquier equipo, considerar los riesgos que entraa la corriente elctrica y
familiarizarse con los procedimientos estndar de prevencin de accidentes.
36
8100-0004-0001 Rev A
Varning!
Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till
personskada. Innan du utfr arbete p ngon utrustning mste du vara medveten om farorna
med elkretsar och knna till vanligt frfarande fr att frebygga skador.
Warning Read the installation instructions before you connect the system to its power source.
Waarschuwing
Varoitus
Attention
Warnung
Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle
anschlieen.
Avvertenza
Advarsel
Aviso
Advertencia!
Varning!
37
8100-0004-0001 Rev A
Warning This unit is intended for installation in restricted access areas. A restricted access area is
where access can only be gained by service personnel through the use of a special tool, lock and
key, or other means of security, and is controlled by the authority responsible for the location.
Waarschuwing
Dit toestel is bedoeld voor installatie op plaatsen met beperkte toegang. Een plaats met beperkte
toegang is een plaats waar toegang slechts door servicepersoneel verkregen kan worden door
middel van een speciaal instrument, een slot en sleutel, of een ander veiligheidsmiddel, en welke
beheerd wordt door de overheidsinstantie die verantwoordelijk is voor de locatie.
Varoitus
Tm laite on tarkoitettu asennettavaksi paikkaan, johon psy on rajoitettua. Paikka, johon psy
on rajoitettua, tarkoittaa paikkaa, johon vain huoltohenkilst psee jonkin erikoistykalun,
lukkoon sopivan avaimen tai jonkin muun turvalaitteen avulla ja joka on paikasta vastuussa
olevien toimivaltaisten henkiliden valvoma.
Attention
Cet appareil est installer dans des zones d'accs rserv. Ces dernires sont des zones auxquelles
seul le personnel de service peut accder en utilisant un outil spcial, un mcanisme de
verrouillage et une cl, ou tout autre moyen de scurit. L'accs aux zones de scurit est sous le
contrle de l'autorit responsable de l'emplacement.
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschrnktem Zutritt vorgesehen. Ein Bereich
mit beschrnktem Zutritt ist ein Bereich, zu dem nur Wartungspersonal mit einem
Spezialwerkzeugs, Schlo und Schlssel oder anderer Sicherheitsvorkehrungen Zugang hat, und
der von dem fr die Anlage zustndigen Gremium kontrolliert wird.
Avvertenza
Questa unit deve essere installata in un'area ad accesso limitato. Un'area ad accesso limitato
un'area accessibile solo a personale di assistenza tramite un'attrezzo speciale, lucchetto, o altri
dispositivi di sicurezza, ed controllata dall'autorit responsabile della zona.
Advarsel
Denne enheten er laget for installasjon i omrder med begrenset adgang. Et omrde med begrenset adgang
gir kun adgang til servicepersonale som bruker et spesielt verkty, ls og nkkel, eller en annen
sikkerhetsanordning, og det kontrolleres av den autoriteten som er ansvarlig for omrdet.
Aviso
Esta unidade foi concebida para instalao em reas de acesso restrito. Uma rea de acesso
restrito uma rea qual apenas tem acesso o pessoal de servio autorizado, que possua uma
ferramenta, chave e fechadura especial, ou qualquer outra forma de segurana. Esta rea
controlada pela autoridade responsvel pelo local.
Advertencia!
Esta unidad ha sido diseada para instalarse en reas de acceso restringido. rea de acceso
restringido significa un rea a la que solamente tiene acceso el personal de servicio mediante la
utilizacin de una herramienta especial, cerradura con llave, o algn otro medio de seguridad, y
que est bajo el control de la autoridad responsable del local.
Varning!
Denna enhet r avsedd fr installation i omrden med begrnsat tilltrde. Ett omrde med
begrnsat tilltrde fr endast tilltrdas av servicepersonal med ett speciellt verktyg, ls och nyckel,
eller annan skerhetsanordning, och kontrolleras av den auktoritet som ansvarar fr omrdet.
38
8100-0004-0001 Rev A
Waarschuwing
Varoitus
Tmn laitteen saa asentaa tai huoltaa ainoastaan Australiassa ja Uudessa Seelannissa
sovellettavan AS/NZS 3260 -standardin kohdan 1.2.14.3 Service Personnel mrittelem
huoltohenkilst.
Attention
Cet quipement ne doit tre install et entretenu que par du personnel d'entretien comme
dfini par la rglementation AS/NZS 3260 Clause 1.2.14.3 Service Personnel.
Warnung
Dieses Gert darf nur von Wartungspersonal gem AS/NZS-Definition 3260, Paragraph
1.2.14.3, "Service Personnel", installiert und gewartet werden.
Avvertenza
Advarsel
Aviso
Este equipamento dever ser instalado e reparado apenas por pessoal de manuteno
qualificado, conforme estipulado em AS/NZS 3260 Clusula 1.2.14.3 Service Personnel.
Advertencia
Este equipo se debe instalar y mantener solamente por personal de servicio, segn definido
por AS/NZS 3260 Clusula 1.2.14.3 Service Personnel.
Varning!
39
8100-0004-0001 Rev A
Warning Only trained and qualified personnel should be allowed to install or replace this
equipment.
Waarschuwing
Varoitus
Ainoastaan koulutettu ja ptev henkilkunta saa asentaa tai vaihtaa tmn laitteen.
Avertissement
Tout installation ou remplacement de l'appareil doit tre ralis par du personnel qualifi et
comptent.
Achtung
Avvertenza
Solo personale addestrato e qualificato deve essere autorizzato ad installare o sostituire questo
apparecchio.
Advarsel
Kun kvalifisert personell med riktig opplring br montere eller bytte ut dette utstyret.
Aviso
Este equipamento dever ser instalado ou substitudo apenas por pessoal devidamente treinado
e qualificado.
Atencin!
Estos equipos deben ser instalados y reemplazados exclusivamente por personal tcnico
adecuadamente preparado y capacitado.
Varning
Denna utrustning ska endast installeras och bytas ut av utbildad och kvalificerad personal.
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must
take special precautions to ensure that the system remains stable. The following guidelines are
provided to ensure your safety:
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to
ensure your safety:
40
8100-0004-0001 Rev A
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
When mounting this unit in a partially filled rack, load the rack from the bottom to
the top with the heaviest component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting
or servicing the unit in the rack.
Waarschuwing
Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert of het daar een
servicebeurt geeft, moet u speciale voorzorgsmaatregelen nemen om ervoor te zorgen dat het
toestel stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te
verzekeren:
Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in
het rek is.
Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van
onderen naar boven te laden met het zwaarste onderdeel onderaan in het rek.
Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te
monteren voordat u het toestel in het rek monteert of het daar een servicebeurt geeft.
Varoitus
Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineess, on noudatettava erityisi
varotoimia jrjestelmn vakavuuden silyttmiseksi, jotta vltytn loukkaantumiselta.
Noudata seuraavia turvallisuusohjeita:
Jos telineess ei ole muita laitteita, aseta laite telineen alaosaan.
Jos laite asetetaan osaksi tytettyyn telineeseen, aloita kuormittaminen sen alaosasta
kaikkein raskaimmalla esineell ja siirry sitten sen ylosaan.
Jos telinett varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen tai
sen huoltamista siin.
Attention
Pour viter toute blessure corporelle pendant les oprations de montage ou de rparation de
cette unit en casier, il convient de prendre des prcautions spciales afin de maintenir la
stabilit du systme. Les directives ci-dessous sont destines assurer la protection du
personnel :
Si cette unit constitue la seule unit monte en casier, elle doit tre place dans le
bas.
Si cette unit est monte dans un casier partiellement rempli, charger le casier de bas
en haut en plaant l'lment le plus lourd dans le bas.
Si le casier est quip de dispositifs stabilisateurs, installer les stabilisateurs avant de
monter ou de rparer l'unit en casier.
Warnung
Zur Vermeidung von Krperverletzung beim Anbringen oder Warten dieser Einheit in einem
Gestell mssen Sie besondere Vorkehrungen treffen, um sicherzustellen, da das System
stabil bleibt. Die folgenden Richtlinien sollen zur Gewhrleistung Ihrer Sicherheit dienen:
Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht
werden.
Bei Anbringung dieser Einheit in einem zum Teil gefllten Gestell ist das Gestell
von unten nach oben zu laden, wobei das schwerste Bauteil unten im Gestell
anzubringen ist.
Wird das Gestell mit Stabilisierungszubehr geliefert, sind zuerst die Stabilisatoren
zu installieren, bevor Sie die Einheit im Gestell anbringen oder sie warten.
Avvertenza
41
8100-0004-0001 Rev A
Advarsel
Unng fysiske skader under montering eller reparasjonsarbeid p denne enheten nr den
befinner seg i et kabinett. Vr nye med at systemet er stabilt. Flgende retningslinjer er gitt
for verne om sikkerheten:
Denne enheten br monteres nederst i kabinettet hvis dette er den eneste enheten i
kabinettet.
Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet
lastes fra bunnen og opp med den tyngste komponenten nederst i kabinettet.
Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres fr
montering eller utfring av reparasjonsarbeid p enheten i kabinettet.
Aviso
Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa estante,
dever tomar precaues especiais para se certificar de que o sistema possui um suporte
estvel. As seguintes directrizes ajud-lo-o a efectuar o seu trabalho com segurana:
Esta unidade dever ser montada na parte inferior da estante, caso seja esta a nica
unidade a ser montada.
Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais
pesados na parte inferior da estante, arrumando-os de baixo para cima.
Se a estante possuir um dispositivo de estabilizao, instale-o antes de montar ou
reparar a unidade.
Advertencia!
Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o posteriormente
durante su mantenimiento, se debe poner mucho cuidado en que el sistema quede bien estable.
Para garantizar su seguridad, proceda segn las siguientes instrucciones:
Colocar el equipo en la parte inferior del bastidor, cuando sea la nica unidad en el
mismo.
Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado,
comenzar la instalacin desde la parte inferior hacia la superior colocando el equipo
ms pesado en la parte inferior.
Si el bastidor dispone de dispositivos estabilizadores, instalar stos antes de montar o
proceder al mantenimiento del equipo instalado en el bastidor.
Varning!
42
8100-0004-0001 Rev A
Warning Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when connected to power
and ground and can cause serious burns or weld the metal object to the terminals.
Waarschuwing
Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden
(inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm
wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden
veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.
Varoitus
Ennen kuin tyskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki
korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne
ovat yhteydess shkvirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai
hitsata metalliesineet kiinni liitntnapoihin.
Attention
Avant d'accder cet quipement connect aux lignes lectriques, ter tout bijou (anneaux, colliers et
montres compris). Lorsqu'ils sont branchs l'alimentation et relis la terre, les objets mtalliques
chauffent, ce qui peut provoquer des blessures graves ou souder l'objet mtallique aux bornes.
Warnung
Vor der Arbeit an Gerten, die an das Netz angeschlossen sind, jeglichen Schmuck
(einschlielich Ringe, Ketten und Uhren) abnehmen. Metallgegenstnde erhitzen sich, wenn
sie an das Netz und die Erde angeschlossen werden, und knnen schwere Verbrennungen
verursachen oder an die Anschluklemmen angeschweit werden.
Avvertenza
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) fr du skal arbeide p utstyr som
er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir
svrt varme og kan forrsake alvorlige brannskader eller smelte fast til polene.
Aviso
Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as
jias que estiver a usar (incluindo anis, fios e relgios). Os objectos metlicos aquecero
em contacto com a corrente e em contacto com a ligao terra, podendo causar
queimaduras graves ou ficarem soldados aos terminais.
Advertencia!
Antes de operar sobre equipos conectados a lneas de alimentacin, quitarse las joyas
(incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a
la alimentacin y a tierra, lo que puede ocasionar quemaduras graves o que los objetos
metlicos queden soldados a los bornes.
Varning!
Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar p
utrustning som r kopplad till kraftledningar. Metallobjekt hettas upp nr de kopplas ihop
med strm och jord och kan frorsaka allvarliga brnnskador; metallobjekt kan ocks
sammansvetsas med kontakterna.
43
8100-0004-0001 Rev A
Warning Do not work on the system or connect or disconnect cables during periods of lightning
activity.
Waarschuwing
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels
aan te sluiten of te ontkoppelen.
Varoitus
Attention
Ne pas travailler sur le systme ni brancher ou dbrancher les cbles pendant un orage.
Warnung
Arbeiten Sie nicht am System und schlieen Sie keine Kabel an bzw. trennen Sie keine ab,
wenn es gewittert.
Avvertenza
Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con
fulmini.
Advarsel
Utfr aldri arbeid p systemet, eller koble kabler til eller fra systemet nr det tordner eller
lyner.
Aviso
No trabalhe no sistema ou ligue e desligue cabos durante perodos de mau tempo (trovoada).
Advertencia!
Varning!
Vid ska skall du aldrig utfra arbete p systemet eller ansluta eller koppla loss kablar.
44
8100-0004-0001 Rev A
Warning To prevent the iDirect MUSiCTM Box Chassis from overheating, do not
operate it in an area that exceeds the maximum recommended ambient temperature of 113 F
(45 C). To prevent airflow restriction, allow at least 6 inches (15.2 cm) of clearance
around the ventilation openings.
Waarschuwing
Om te voorkomen dat de iDirect MUSiCTM Box Chassis oververhit raakt, dient u deze
niet in een gebied te bedienen waar de maximaal aanbevolen omgevingstemperatuur van
45 C wordt overschreden. Om luchtstroombeperkingen te voorkomen, dient u minstens
15 cm speling rond de ventilatieopeningen te laten.
Varoitus
Jotta iDirect MUSiCTM Box Chassis ei kuumentuisi liikaa, sit ei saa kytt alueella,
jonka lmptila ylitt suositellun maksimiympristlmptilan 45 C. Ilmanvaihdon
silyttmiseksi on tuuletusaukkojen ymprille jtettv ainakin 15,2 cm:n tila.
Attention
Pour viter toute surchauffe du iDirect MUSiCTM Box Chassis, il est recommand de
maintenir une temprature ambiante infrieure 45 C. Pour assurer une parfaite
circulation de l'air autour du routeur, prvoyez un espace minimum de 15 cm autour des
ouvertures de ventilation.
Warnung
Um den iDirect MUSiCTM Box Chassis vor berhitzung zu schtzen, vermeiden Sie
Benutzung des Gerts in einer Gegend, in denen die Umgebungstemperatur das
empfohlene Maximum von 45 C berschreitet. Um eine Behinderung der Luftzirkulation
zu vermeiden, stellen Sie sicher, da um die Khlungsffnungen herum ein Raum von
mindestens 15,2 cm frei bleibt.
Avvertenza
Per evitare che il iDirect MUSiCTM Box Chassis si surriscalda, non utilizzatelo in una
zona dove la temperatura ambiente eccede le massime raccomandate di 113 F (45 C).
Per evitare di bloccare il passaggio dell'aria, lasciate almeno 6 pollici (15.2 cm) di spazio
libero attorno alle aperture per la ventilazione.
Advarsel
Forhindre at iDirect MUSiCTM Box Chassis blir overopphetet ved ikke bruke den p et
sted der den anbefalte omgivelsestemperaturen overstiger 45 C. Unng at
luftsirkulasjonen reduseres ved ha en klaring p minst 15,2 cm rundt
ventilasjonspningene.
Aviso
Advertencia!
Para impedir que el iDirect MUSiCTM Box Chassis se caliente, no lo use en un rea que
exceda la temperatura ambiente mxima recomendada de 113 F (45 C). Con el fin de no
restringir el flujo de aire, deje un espacio de un mnimo de 6 pulgadas (15,2 cm) alrededor
de los orificios de ventilacin.
Varning!
Frhindra att iDirect MUSiCTM Box Chassis blir verhettad genom att inte anvnda den
45
8100-0004-0001 Rev A
Warning: The ports labeled "+24VDC", "TX Out", "10/100 LAN", Console, RX Out and
"RX In" are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to
other SELV circuits. Avoid connecting these circuits to telephone network
voltage (TNV) circuits.
Waarschuwing
De poorten die gelabeld zijn met "+24VDC", "TX Out", "10/100 LAN", Console, RX
Out en "RX In" zijn veiligheidscircuits met extra-laag voltage (SELV). SELV-circuits
mogen alleen maar op andere SELV-circuits worden aangesloten. Sluit deze circuits niet
op telefoonnetwerkvoltage-circuits (TNV) aan.
Varoitus
Varoitus Portit, joissa on merkint "+24VDC", "TX Out", "10/100 LAN", Console, RX
Out ja "RX In", ovat suojattuja erittisen alhaisen jnnitteen (SELV) piirej. SELV-piirit
tulisi liitt ainoastaan toisiin SELV-piireihin. Vlt kytkemst nit piirej
puhelinverkkojnnitteen (TNV) piireihin.
Attention
Les ports "+24VDC", "TX Out", "10/100 LAN", Console, RX Out et RX In sont
des circuits SELV ( Safety Extra-Low Voltage :trs basse tension de scurit). Les
circuits SELV ne devant tre connects qu' d'autres circuits du mme type, il est
recommand de ne pas les raccorder des circuits TNV ( Telephone Network Voltage
:tension de rseau tlphonique).
Warnung
Die Ports mit der Bezeichnung "+24VDC", "TX Out", "10/100 LAN", Console, RX
Out und "RX In" sind SELV-Schaltkreise (safety extra-low voltage circuits - SicherheitsNiedrigspannungskreise). SELV-Schaltkreise sollten nur an andere SELV-Schaltkreise
angeschlossen werden. Achten Sie darauf, diese Schaltkreise nicht an TNV-Schaltkreise
(telphone network voltage - Telefonnetzspannung) anzuschlieen.
Avvertenza
Le porte etichettate "+24VDC", "TX Out", "10/100 LAN", Console, RX Out e "RX
In" sono circuiti di sicurezza a basso voltaggio (Safety Extra-Low Voltage SELV). Evitate
di collegare questi circuiti con circuiti a voltaggio rete telefonica (Telephone Network
Voltage - TNV).
Advarsel
Utgangene merket "+24VDC", "TX Out", "10/100 LAN", Console, RX Outog "RX
In" er sikkerhetskretser (SELV) med ekstra lav spenning. SELV-kretser skal bare kobles til
andre SELV-kretser. Unng koble disse kretsene til kretser for
telefonnettspenning(TNV).
Aviso
As portas assinaladas com "+24VDC", "TX Out", "10/100 LAN", Console, RX Out e
"RX In" so circuitos de segurana de baixa tenso (SELV). Os circuitos de segurana de
baixa tenso s devero ser conectados a outros circuitos de segurana de baixa tenso.
46
8100-0004-0001 Rev A
Los puertos "+24VDC", "TX Out", "10/100 LAN", Console, RX Out y "RX In" son
circuitos de seguridad de voltaje extra bajo ( SELV). Estos circuitos SELV deben
conectarse solamente a otros circuitos SELV. Evite conectar este tipo de circuitos a
circuitos de la red de voltaje del telfono (TNV).
Varning!
Portarna med beteckningen "+24VDC", "TX Out", "10/100 LAN", Console, RX Out
och "RX In" r SELV-kretsar (skyddskretsar fr mycket lg spnning). SELV-kretsar fr
endast kopplas till andra SELV-kretsar. Undvik att koppla dessa kretsar till TNV-kretsar
(kretsar med telefonntspnning).
Warning: Unplug the power cord before you work on a system that does not have an on/off
switch.
Waarschuwing
Voordat u aan een systeem werkt dat geen aan/uit schakelaar heeft, dient u de stekker
van het netsnoer uit het stopcontact te halen.
Varoitus
Ennen kuin teet mitn sellaiselle jrjestelmlle, jossa ei ole kaksiasentokytkint, kytke
irti virtajohto.
Attention
Warnung
Bevor Sie an einem System ohne Ein/Aus-Schalter arbeiten, ziehen Sie das Netzkabel
heraus.
Avvertenza
Advarsel
Fr det skal utfres arbeid p et system som ikke har en av/p-bryter, skal
strmledningen trekkes ut.
Aviso
Advertencia
Varning!
47
8100-0004-0001 Rev A
Waarschuwing
Varoitus
Attention
Un disjoncteur bipolaire facile d'accs doit tre intgr dans le cblage fixe.
Warnung
Avvertenza
Advarsel
Aviso
Advertencia
Varning!
Waarschuwing
Varoitus
48
8100-0004-0001 Rev A
Attention
Warnung
Avvertenza
Advarsel
Aviso
Advertencia!
Varning!
Warning Never defeat the ground conductor or operate the equipment in the absence of a
suitably installed ground conductor. Contact the appropriate electrical inspection authority
or an electrician if you are uncertain that suitable grounding is available.
Waarschuwing
Varoitus
l koskaan ohita maajohdinta tai kyt laitteita ilman oikein asennettua maajohdinta.
Ota yhteytt asianmukaiseen shktarkastusviranomaiseen tai shkasentajaan, jos olet
epvarma maadoituksen sopivuudesta.
Attention
Warnung
Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gert ohne einen
sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob
eine sachgerechte Erdung vorhanden ist, wenden Sie sich an den zustndigen
elektrischen Fachmann oder einen Elektriker.
Avvertenza
49
8100-0004-0001 Rev A
Omg aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta
kontakt med det riktige organet for elektrisk inspeksjon eller en elektriker hvis du er
usikker p om det finnes velegnet jording.
Aviso
Nunca anule o condutor terra nem opere o equipamento sem ter um condutor terra
adequadamente instalado. Em caso de dvida em relao ao sistema de ligao terra,
contacte os servios locais de inspeco elctrica ou um electricista qualificado.
Advertencia
Varning!
Koppla aldrig frn jordledningen och anvnd aldrig utrustningen utan en p lmpligt stt
installerad jordledning. Om det freligger oskerhet huruvida lmplig jordning finns
skall elektrisk besiktningsauktoritet eller elektriker kontaktas.
Warning When installing the unit, the ground connection must always be made first and
disconnected last.
Waarschuwing
Bij de installatie van het toestel moet de aardverbinding altijd het eerste worden gemaakt en
het laatste worden losgemaakt.
Varoitus
Attention
Lors de l'installation de l'appareil, la mise la terre doit toujours tre connecte en premier et
dconnecte en dernier.
Warnung
Der Erdanschlu mu bei der Installation der Einheit immer zuerst hergestellt und zuletzt
abgetrennt werden.
Avvertenza
Advarsel
50
8100-0004-0001 Rev A
Aviso
Ao instalar a unidade, a ligao terra dever ser sempre a primeira a ser ligada, e a
ltima a ser desligada.
Advertencia!
Varning!
Vid installation av enheten mste jordledningen alltid anslutas frst och kopplas bort sist.
Warning Do not touch the power supply when the power cord is connected. For systems with a
power switch, line voltages are present within the power supply even when the power switch is
off and the power cord is connected. For systems without a power switch, line voltages are
present within the power supply when the power cord is connected.
Waarschuwing
U dient de voeding niet aan te raken zolang het netsnoer aangesloten is. Bij systemen met
een stroomschakelaar zijn er lijnspanningen aanwezig in de voeding, zelfs wanneer de
stroomschakelaar uitgeschakeld is en het netsnoer aangesloten is. Bij systemen zonder een
stroomschakelaar zijn er lijnspanningen aanwezig in de voeding wanneer het netsnoer
aangesloten is.
Varoitus
Attention
Ne pas toucher le bloc d'alimentation quand le cordon d'alimentation est branch. Avec les
systmes munis d'un commutateur marche-arrt, des tensions de ligne sont prsentes dans
l'alimentation quand le cordon est branch, mme si le commutateur est l'arrt. Avec les
systmes sans commutateur marche-arrt, l'alimentation est sous tension quand le cordon
d'alimentation est branch.
Warnung
Berhren Sie das Netzgert nicht, wenn das Netzkabel angeschlossen ist. Bei Systemen mit
Netzschalter liegen Leitungsspannungen im Netzgert vor, wenn das Netzkabel
angeschlossen ist, auch wenn das System ausgeschaltet ist. Bei Systemen ohne Netzschalter
liegen Leitungsspannungen im Netzgert vor, wenn das Netzkabel angeschlossen ist.
Avvertenza
Advarsel
51
8100-0004-0001 Rev A
Advertencia!
Varning!
Warning Before working on a chassis or working near power supplies, unplug the power
cord on AC units; disconnect the power at the circuit breaker on DC units.
Waarschuwing
Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom
toestellen de stekker van het netsnoer uit het stopcontact te halen; voor gelijkstroom
toestellen dient u de stroom uit te schakelen bij de stroomverbreker.
Varoitus
Attention
Warnung
Bevor Sie an einem Chassis oder in der Nhe von Netzgerten arbeiten, ziehen Sie bei
Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei Gleichstromeinheiten den
Strom am Unterbrecher ab.
Avvertenza
52
8100-0004-0001 Rev A
Advarsel
Aviso
Advertencia!
Varning!
Warning Secure all power cabling when installing this unit to avoid disturbing
field-wiring connections.
Waarschuwing
Zet alle stroomkabels vast wanneer dit toestel wordt genstalleerd om te voorkomen dat
de verbindingen van de veldbedrading worden verstoord.
Varoitus
Attention
Lors de l'installation de cet appareil, fixer tous les cbles d'alimentation pour viter de
provoquer des perturbations aux raccordements des cblages propres au site.
Warnung
Bei der Installation dieser Einheit die Netzverkabelung befestigen, um die Strung von
Feldkabelanschlssen zu vermeiden.
Avvertenza
Advarsel
Aviso
Para evitar problemas com as ligaes de rede de campanha, prenda todos os cabos de
corrente quando instalar esta unidade.
53
8100-0004-0001 Rev A
Advertencia!
Sujetar todo el cableado de alimentacin cuando se instale este equipo para evitar que se
mezcle con las conexiones del cableado "in situ".
Varning!
Fst allt starkstrmskablage vid installation av denna enhet s att fltkopplingen inte
rubbas.
Warning Care must be given to connecting units to the supply circuit so that wiring is not
overloaded.
Waarschuwing
Let erop dat de toestellen op voedingscircuits worden aangesloten zonder het vermogen
van de bedrading te overschrijden.
Varoitus
Avertissement
Veillez bien connecter les units au circuit d'alimentation afin de ne pas surcharger les
connections.
Achtung
Beim Anschlieen der Gerte an das Stromnetz ist darauf zu achten, da die
Schaltverbindungen nicht berlastet werden.
Avvertenza
Advarsel
Aviso
Atencin!
Varning
Var noga vid anslutning av enheter till matarstrmkretsen s att ledningarna inte
verbelastas.
12 Acronyms
iDirect MUSiC Box Installation and Users Guide
54
8100-0004-0001 Rev A
The following are commonly used acronyms in iDirect products and the satellite industry.
AGC
ARP
BIOS
BIST
BOM
BUC
CID
CN
DAMA
dB
dBm
DVM
ECC
EIRP
FEC
FOB
FPGA
HPA
HPB
HW
ICMP
IFL
IP
LA
LAN
LNB
LO
MAE
M&C
NAT
NMS
NOC
NRD
OBO
ODU
OMC
OMT
55
8100-0004-0001 Rev A
OS
QA
QPSK
RF
RFT
RT
Rx
S/N
SCPC
SLA
SNR
SSA
SSPA
STP
SU
SW
TCP
TDM
TDMA
TECC
TPC
TRF
TWTA
Tx
UA
UCP
UDP
UPC
UTP
VSAT
WAN
Operating System
Quality Assurance
Quadsrature Phase Shift Keying
Radio Frequency
Radio Frequency Terminal
Real Time
Receive
Serial Number
Single Channel Per Carrier
Service Level Agreement
Signal to Noise Ratio
Service and Support Agreement
Solid State Power Amplifyer
Shielded Twisted Pair
Super User
Software
Transmission Control Protocol
Time Division Multiplexing
Time Division Multiple Access
Turbo Error Correction Coding
Turbo Product Code
Transmit Reject Filter
Traveling Wave Tube Amplifyer
Transmit
User Acceptance
Uplink Control Processing
User Datagram Protocol
Uplink Power Control
Unshielded Twisted Pair
Very Small Aperture Terminal
Wide Area Network
56
8100-0004-0001 Rev A
13 Glossary
ACCESS TIME - The time intervals between the request for a transfer of data to or from a storage
device and the point at which the operation is complete.
ACK - A code character indicating a positive acknowledgment that data has been received correctly.
Also used as a "ready" reply in some communication protocols.
ADDRESS - A coded representation of the destination of data or of their originating terminal.
AIDAL - Anti-Intrusion Defeater and Locator, a tool to combat the problem of uplink interference or
double illumination by both blocking uplink interference and assisting in
determining its geographic location.
ANALOG TRANSMISSION - Transmission of a continuous electrical signal that is modulated to
carry information.
ANSWER BACK - A reply message from a terminal, manually or automatically initiated, to verify that
the terminal has been addressed and is operational.
BAND - The frequency spectrum between 2 defined limits.
BANDWIDTH - The difference between the high and low frequency of a band.
BAUD - A unit of signaling speed equal to conditions or signal elements per second.
BEACON - Low-power carrier transmitted by a satellite, which supplies the controlling engineers on
the ground with a means of monitoring telemetry data, tracking the satellite, or
conducting propagation experiments. This tracking beacon usually uses a horn or
omni antenna. .
BREAK - A transmission interruption, usually to allow a controlled terminal to interrupt the controlling
computer.
BUFFER - Temporary storage used to accommodate differences in speed of data flow when
transmitting from one device to another.
BYTE - A group of bits treated as a unit and forming 1 character. Typically 8 bits form a byte.
CHECKSUM - A numerical value that produces a predetermined constant when added to the sum of a
specified group of bytes. Used in summation checks.
CIRCUIT - A communications link between 2 or more points.
CLOCK - A timing device usually providing a continuous series of timing pulses.
57
8100-0004-0001 Rev A
58
8100-0004-0001 Rev A
GAIN CONTROL - Gain Control of the transponder is done via TT&C commands to the Flux
Control Attenuator (FCA) in the satellite. The FCA is used to set the incident flux
density necessary to saturate each transponder (SFD).
GROUP DELAY - Group Delay refers to phase variation across the transponder bandwidth.
Wideband FM signals and high-speed phase shift keyed data transmission are
particularly sensitive to the effects of Group Delay.
HALF DUPLEX - Transmission in both directions on a circuit, but not simultaneously.
HANDSHAKING - The exchange of predetermined signals between 2 modems , computers, or other
devices when a connection is established.
HARDWARE - Physical equipment or components as opposed to computer programs(software),
HEADER - The control information prefixed in a message test, e.g. source or destination code,
priority, or message type.
HEXADECIMAL - A number system with 16 elements represented by O through A through F.
INTERFACE - A common boundary between two entities, which can be mechanical, electrical, or
functional.
INTERMODULATION DISTORTION - Undesired frequencies called intermodulation products
are generated when an amplifier is operated in the nonlinear region of its input-tooutput transfer curve and multiple carriers are present. Intermodulation distortion
results from the interaction of these multiple carriers with each other when they
are passed through an amplifier with a nonlinear transfer curve.
LINEARIZER - A Traveling Wave Tube Amplifier (TWTA) distorts the RF signal during the
amplification process. This distortion is in both magnitude and phase. A linearizer
pre-distorts the signal in the opposite direction of the TWTA. As a result, when
the RF signal is pre-distorted by a linearizer and then re-distorted by the TWTA,
it is closer to the desired signal at higher output power. .
MENU - A list of selections.
MODEM - A device that transforms a signal into a from suitable for transmission over the telephone
network or data circuit
MULTIPLEX - A method of sending and receiving multiple signals over a communication channel
without loss of information.
MULTIPLEXING - To interleave and transmit a number of different messages over a single circuit.
NAK - Negative acknowledgment, has been received incorrectly. in some communication protocols. A
message that implies that data has been received incorrectly. Also used as a "not
ready" reply in some communication protocols.
iDirect MUSiC Box Installation and Users Guide
59
8100-0004-0001 Rev A
60
8100-0004-0001 Rev A
61
8100-0004-0001 Rev A
14 Appendix
14.1 Coaxial Cable Specification
The coaxial cable used to connect the iDirect MUSiCTM Box Chassis to the ODU equipment should
be very high quality cable. iDirect recommends that you use solid copper center conductor quad
shield coaxial cable with a minimum of 60% + 40% braid and double foil shield to connect the
MUSiCTM Box to the ODU equipment. The center conductor must be straight and extend 1/8 inch
(3.2mm) beyond the end of the F-connector, and the connector should be securely crimped to the
cable. The following cables are recommended:
Note:
iDirect does not recommend using RG-59 with solid bare copper center conductor
unless the IFL length is less than 120 feet (37 m). If lower RF insertion loss is
required due to the distant between the IDU chassis and the ODU equipment,
then RG-11 or other types of coax can be used.
If you use different types of coaxial cable other than quad shield RG-6 or RG-11, the following
problems can appear:
Co-channel Interference If signals at the same frequency are carried on long, parallel runs of
coaxial cable (in cable trays, riser, ect) interference can occur between the signals. Higher
quality cable helps to prevent this with better shielding. Co-channel interference will cause
degradation in higher packet rate loss.
Damage to the iDirect MUSiCTM Box Chassis connectors The chassis connectors are
designed for RG-6 or RG-11 cable and connectors. Larger cables can damage the connectors.
High signal return loss High quality cable and correct connectors help ensure an optimal
return loss of 10 dB or more.
62
8100-0004-0001 Rev A
7.3.1
Shown below is the typical instruction for putting a Type-F Connector onto a RG-6 cable.
Step 1: Remove jacket material to 3/8 of an
inch (0,95 cm). Or using a 2-step
Coax Stripper.
Step 2: Fold the braid back over the jacket.
Step 3: Remove foil and cut dielectric to length of inch (0,64cm). Be careful not to cut into
the copper of the center conductor. Remove any dielectric residue.
Step 4: If the foil is burred, twist so that the corner at Point A (area where the dielectric material
was removed) is smooth and provides a lead for the connector mandrel.
Step 6: Install connector mandrel over foil and underneath the braid; trim braid if desired. Point
A should be approximately even with the inner surface of connector.
Step 7: Crimp the connector with the proper crimp tool.
Step 8: Inspect terminated connector as shown below.
63
8100-0004-0001 Rev A
Table 14-1 lists the signal and pinouts for the asynchronous serial Console Port, and the RJ-45 to DB9 female DTE adapter.
Console Port
(DTE)
RTS
DTR
TxD
GND
GND
RxD
DSR
CTS
RJ-45 Pin
1
2
3
4
5
6
7
8
RJ-45 to DB-9
Terminal Adapter
8
6
2
NC
5
3
4
7
Console
Device
CTS
DSR
RxD
GND
GND
TxD
DTR
RTS
64
8100-0004-0001 Rev A
Use a Category 3 UTP straight-through cable when connecting 10 Base T port to a LAN Hub.
Use a Category 3 UTP crossover cable when connecting to a PC or other Ethernet device.
Use a Category 5 UTP straight-through cable when connecting 10 Base T port to a LAN Hub.
Use a Category 5 UTP crossover cable when connecting to a PC or other Ethernet device.
Note: iDirect only supplies one 7 foot Category 5 UTP cables to connect the iDirect
MUSiCTM Box Chassis to the LAN Hub or Switch. If additional cables or
different lengths are needed, they can be bought commercially.
To determine the type of RJ-45 cable, examine the sequence of the colored wires as follows:
Straight-through The colored wires are in the same sequence at both ends of the cable.
Crossover The first (far left) colored wire at one end of the cable is the third colored wire at
the other end of the cable and the second colored wire at one end of the cable is the sixth
colored wire at the other end of the cable.
Table 14-2 list the pinouts for the Ethernet ports of the MUSiCTM Box.
Description
Tx+
TxRx+
Rx-
Figure 14-2 shows the RJ-45 cable connectors Plug and Receptacle
65