‘See your local hobby desler for these other
TACK CLOTH Torta
Petes detach
Proparing the Top Flite SmartCut Tool for use
“The SmartOat tool has two malor pars: he TOOL
[BODY wich holds the blades, and tne SPACER
PLATE, which ereatos const 1/8" 9° 1/16"
‘varias, Depending on the appicaton (as these
‘istucsons Sepia), tne tol body may be used wth
‘er wihout tne spacer ps allached.
“CAUTION: Blades are sharp.
KEEP OUT OF REACH OF CHILOREN.
Installing blades using screw and
thumb nut.
Bofore using tho SmarCut
100), stall the two serene nto
‘he les on the attem oF
‘the tool body. To prevent
those serous fom tur
Ing when te bles ore
Tightoned, you may
‘9p @ drop oft
GR gue to cach
‘sore head,
‘Avo gtling
‘any give nto
the screw
Tends or
onto the
Surtaces of
the toot
™ MoNoKore:
SmartCut™
‘TRIMMING TOOL INSTRUCTIONS
‘Whether you're a fs-tme kt bulder or an expexi-
‘eneext po, You can create more alacive frishoo—
‘asler—usig Top Flo's SrextCtThiening Too,
“Ths unique timing tool makes It easy 10
‘cover iactionaly fut areas, such as inside
‘comers and wing edges. The SmartCut ool
Creates smooth, straight cuts and uniform
‘Sverlaps. resin In heey nelle seams.
‘Use the SrexiCut oo folowing the qudeines
presertedinsde to cover wih Top Fite ManoKote*
rary other coverng mati.
B ‘Too! blade held in place by thumb nut.
“The SrextCut tool
uses standard
replaceable #11
bades, stalls on
the sorows (Step 1)
and retained by
‘hub nuts. By
Keosering the thums
rut, youmay aust,
thebiads's eating
‘dept for apps
fons as required,
NOTE: Blades wil
(wear quick ang shoud ba placed te instant any
resitane or skpoing Is nesiced when euting. The
‘SmartGut fo! tm moet easly with rh Bes
Five basic cuts that can be made with the SmartCut tool
During th process of covering your model, you wil ncounte situations that can be best hanced with one ofthe folowing citing techniguss. They are sted low with
the moe uso teiviquas re
1. inside cut with 1/8” overtap.
‘a “nade cat sa cut made from te aces sce
lihe coverng. The spacer pat snot used
Fre, ron the covering onto your mace up to, but Pot
soured he comers. Taxis tne SmarOUt fol and 3 FS
bcos to cutng dooth of approximate 1/16"
Now sige te tou along the sacs of your med
resting he bottom ofthe fol
ody fat agast the wood.
Ths tenwsa 18" were,
vic be toned oan
serene,
Lee thsrethos to
tein coverng without
fut covering that
Fras afeany been
honed don
2. inside cut with minimal overlap.
“This cus similar to the inside ut with 1
covatap, an is rad using the same lade depth anc
‘thot the spacer pata
“me aference s tat the too
bod ted so that ts
beveled edge shes against
your ode, as shown
faking very close cut,
‘Tis metho
produces 8 raat
Soom tet witty
‘soppears in
‘mare ora edges,
3. outside cut with 1/8” overtap.
“oie cu a 3 pared cain th at
crate fom ha coving rents son, Bsce
Satna, omer het rom your maser
Scratching rainy roo he coven oan re
Ermer tig nod
“ornate bec ach Saat o's spacer
hte athe op Feo cra toner te eaten
{fo 8 onan Se nebece Spine greter han
a2 Cis sig th soe: pte aoe oe,
soe nt
se DONOT et tetrinve
REET Hitwoud reat cute
7 ay ec
ral wee hk
4. outside cut with 1/16” overiap.
Make this cut inthe same manner as the outside
cut with 1/8" overlap—out attach the spacer pate to
the too! body wth he fogp facing downwarG, Mss
postions the blade approximate 1/76" rom the
ge 0! your model. Use tus cutting mena or
perlecteeame song hn tal sriaces and edges.
spaeg oat ope dove
5. using the SmartCut tool to out
through only one layer of covering.
It reat cares used, the SmartGut tool may be
used to cut a srg ayer of covering on 2 moet
\wifout cutting the wood or covering underneath,
‘This method is most usefl for euting in ane
‘covering tll sutaces,
However, demands tat
the ade cuting depth be eat
{gan absolute minima,
Test the Bade det
oh scrap Menokcts ———
‘Consisterty good ]
results reaure me
and practi AN
Newell t50
much Blade .
extend, oF press.
toohardon ne /
tock You cous
inachertently damage your moc by
®uttng into the wood, or through
‘ovarg that Pas ready boen append,
DONO! THY TO MAKE THIS CUT WITHOUT USING
NEW, VERY SHARP BLACES!
Hints for using the Top Flite SmartCut tool:
+ Cut wah one amooth stoke, Avold stopping and
Staring.
+= Whe outing, hold the teal ata consistant angle so
the overap & consent along the entra length,
+ Aer use, aout he Bada 20 they ae uy react
‘ed inside the foo! body, Then attach the spacer
Plate wih the Top Ftiogo facing dowrarc. For
Salty, the Blades shave net oe le exposed