Академический Документы
Профессиональный Документы
Культура Документы
2-5
Metric
English
1.5 Y
13 lb in
2.0 Y
18 lb in
4Y
35 lb in
Front and Rear Side Door Opening Frame Reveal Molding Screw
1.5 Y
13 lb in
3.5 Y
31 lb in
4Y
35 lb in
1.5 Y
13 lb in
4.5 Y
40 lb in
1.5 Y
13 lb in
1.5 Y
13 lb in
4Y
35 lb in
4Y
35 lb in
1.5 Y
13 lb in
4Y
35 lb in
4Y
35 lb in
2.5 Y
22 lb in
2.5 Y
22 lb in
Repair Instructions
Body Panel Paint Protector
Replacement (VGC)
Object-ID=2054469 Owner=jforce01 LMD=14-jul-2008 LMB=mgraha01
2-6
Exterior Trim
1872835
Component Name
Front Fender Center Molding Assembly
Procedure
1. Open the door on the side the front fender molding is being serviced from.
2. Working from inside the hinge pillar area, insert a small 8 mm socket on a ratchet over the plastic retainer
clips to release the pressure.
3. Begin releasing the retainers at the bottom of the molding and work towards the top.
4. When the first lower retainer clip is released, insert a small plastic flat-bladed tool between the exterior body
panel and the molding assembly to prevent the retainer from re-engaging back into the fender panel hole.
5. Disconnect the electrical harness connector from the lamp housing.
6. Connect the electrical harness lamp socket to the lamp housing.
7. Position the molding retainers to the fender holes.
8. Using the palm portion of the hand, secure the retainers to the fender holes.
9. An light audible click will be heard when each retainer is secure to the fender panel.
Front Side Turn Signal Lamp Assembly
Tip: Disconnect the electrical connector prior to removing the center molding assembly from the fender.
Exterior Trim
2-7
1875451
Component Name
Preliminary Procedures
1. Remove the interior liftgate trim panel. Refer to Liftgate Trim Panel Replacement (Short Body) on page 2135 or Liftgate
Trim Panel Replacement (Long Body) on page 2136.
2. Disconnect the electrical connector for the license plate lamps.
3. Disengage the electrical harness grommet from the outer liftgate panel.
Rear Liftgate Upper Applique Nut (Qty: 6)
1
2
3
Procedure
Transfer parts as needed to the new applique panel.
2-8
Exterior Trim
2244886
Component Name
Preliminary Procedures
1. Remove the interior liftgate trim panel. Refer to Liftgate Trim Panel Replacement (Short Body) on page 2135 or Liftgate
Trim Panel Replacement (Long Body) on page 2136.
2. Disconnect the electrical connector for the license plate lamps.
3. Disengage the electrical harness grommet from the outer liftgate panel.
4. Disconnect the lock rod to the outside liftgate handle.
Liftgate Center Applique Nut (Qty: 5)
1
2
3
Procedure
Transfer the internal parts as needed to the new center applique panel.
Exterior Trim
2-9
2244878
Component Name
Preliminary Procedures
1. Open and support the rear liftgate assembly.
2. Remove the liftgate window garnish molding. Refer to Liftgate Garnish Molding Replacement on page 2134.
Liftgate Upper Applique Nut (Qty: 4)
1
Procedure
1. Release the button clips from the upper outer liftgate panel.
2. Close the rear liftgate in order to remove the spoiler assembly.
3. Disconnect the rear washer nozzle extension hose.
4. Disconnect the electrical connector for the rear high mounted stop lamp.
5. Ensure all the foam gaskets are in place on the button clips and retainer bolts prior to re-assembly of the
spoiler onto the liftgate panel.
High Mount Stop Lamp Assembly
Procedure
Remove the high mount stop lamp. Refer to High Mount Stop Lamp Replacement (Short Body) on page 4187 or
High Mount Stop Lamp Replacement (Long Body) on page 4189 and transfer.
2-10
Exterior Trim
1875794
Component Name
Preliminary Procedures
1. Open and support the rear liftgate assembly.
2. Remove the liftgate window garnish molding. Refer to Liftgate Garnish Molding Replacement on page 2134.
Spoiler Nut (Qty: 7)
1
Procedure
1. Release the button clips from the upper outer liftgate panel.
2. Close the rear liftgate in order to remove the spoiler assembly.
3. Disconnect the rear washer hose.
4. Disconnect the electrical connector for the rear high mounted stop lamp.
5. Remove the rear center high mounted stop lamp. Refer to High Mount Stop Lamp Replacement (Short
Body) on page 4187 or High Mount Stop Lamp Replacement (Long Body) on page 4189 and transfer.
6. Ensure all the foam gaskets are in place on the button clips and retainer bolts prior to re-assembly of the
spoiler onto the liftgate panel.
Exterior Trim
2-11
2440048
Component Name
Preliminary Procedures
1. Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper
Fascia Replacement (Short Body) on page 353.
2. Release the seven tabs securing the fog lamp opening bezel to the front upper bumper fascia.
3. Push the bezel outward in order to release.
1
Procedure
1. Hold the front fog lamp bezel in one hand and release the four tabs securing the front fog lamp opening
cover to the front fog lamp bezel.
2. Release the fog lamp bezel from the front fog lamp opening cover.
2-12
Exterior Trim
2440469
Component Name
Front License Plate Bracket Screw (Qty: 2)
Caution: Refer to Fastener Caution on page 07.
Front License Plate Bracket
Procedure
1. Remove the two screws from the front license plate bracket.
2. Remove the front license plate bracket from the lower bumper fascia.
Exterior Trim
2-13
2448999
Component Name
Front License Plate Bracket Screw (Qty: 4)
Caution: Refer to Fastener Caution on page 07.
Hand tighten the screws.
Front License Plate Bracket
Procedure
Remove the front license plate bracket from the upper and lower front bumper fascia.
2-14
Exterior Trim
2533727
Component Name
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia
Replacement (Short Body) on page 353
1
Procedure
Release the emblem / nameplate from the radiator upper grille assembly.
Exterior Trim
2-15
2244601
Component Name
Preliminary Procedure
Turn the wheel assembly outward in order to access the lower front wheel opening molding screws.
2-16
Exterior Trim
2244603
Component Name
Preliminary Procedure
Remove the rear tire and wheel assembly. Refer to Tire and Wheel Removal and Installation on page 1674.
Exterior Trim
2-17
2245777
Component Name
Preliminary Procedure
Remove both front bumper lower fascia side grilles. Refer to Front Bumper Lower Fascia Side Grille Replacement (LWB) on
page 218.
1
Procedure
1. Release the ten front bumper fascia locking tabs from the front bumper lower fascia grille.
2. Pull the grille rearward from the inside of the front bumper fascia.
2-18
Exterior Trim
2447006
Component Name
Preliminary Procedure
Remove the front bumper fascia in order to access and remove the front bumper lower fascia side grille. Refer to Front Bumper
Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia Replacement (Short Body) on page 353.
Front Bumper Lower Fascia Side Grille
1
Procedure
Release the locking tabs securing the front bumper lower fascia side grille to the front bumper upper fascia and
push outward in order to remove.
Exterior Trim
2-19
2440863
Component Name
Preliminary Procedure
Remove the radiator upper grille. Refer to Radiator Upper Grille Replacement (Short Body) on page 221 or Radiator Upper Grille
Replacement (Long Body) on page 222.
1
2-20
Exterior Trim
2533726
Component Name
Preliminary Procedure
1. Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper
Fascia Replacement (Short Body) on page 353.
2. Remove the radiator grille emblem / nameplate. Refer to Radiator Grille Emblem/Nameplate Replacement on page 214.
1
Procedure
Release the tabs from the radiator upper grille assembly and remove.
Exterior Trim
2-21
2533730
Component Name
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia
Replacement (Short Body) on page 353.
1
Procedure
Release the ten lower front bumper fascia locking tabs from the radiator grille and remove the grille.
2-22
Exterior Trim
2533716
Component Name
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia
Replacement (Short Body) on page 353.
Radiator Upper Grille Assembly
1
Procedure
Release the upper radiator grille from the ten locking tabs on the front bumper upper fascia and remove.
Exterior Trim
2-23
2440807
Component Name
Preliminary Procedure
Remove the front bumper fascia assembly. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front
Bumper Fascia Replacement (Short Body) on page 353.
Radiator Lower Grille
Procedure
1. Reposition the front fog lamp and front object sensor wiring harness in order to remove the radiator lower
grille.
2. Release the 18 upper front bumper fascia tabs from the radiator lower grille.
3. Pull the grille assembly rearward from inside the front bumper fascia.
4. Remove the radiator lower grille assembly.
2-24
Exterior Trim
2449630
Component Name
Preliminary Procedures
1. Remove the front bumper fascia energy upper absorber. Refer to Front Bumper Fascia Energy Upper Absorber
Replacement (Long Body) on page 346 or Front Bumper Fascia Energy Upper Absorber Replacement (Short Body) on
page 347.
2. Remove the front bumper fascia energy lower absorber. Refer to Front Bumper Fascia Energy Lower Absorber
Replacement (Long Body) on page 348 or Front Bumper Fascia Energy Lower Absorber Replacement (Short Body) on
page 349.
Lower Radiator Grille Assembly
1
Procedure
1. Release the grille tabs securing the lower grille to the outer molding.
2. Remove the lower grille from the alignment pins on the outer molding.
Exterior Trim
2-25
2533718
Component Name
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia
Replacement (Short Body) on page 353.
Radiator Upper Grille Lower Insert (Qty: 2)
1
Procedure
Release the locking tabs securing the insert to the radiator upper grille assembly.
2-26
Exterior Trim
2533728
Component Name
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia
Replacement (Short Body) on page 353.
Radiator Grille Upper Insert (Qty: 2)
1
Procedure
Release the locking tabs securing the inserts to the radiator upper grille assembly.
Exterior Trim
2-27
2533719
Component Name
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement (Long Body) on page 352 or Front Bumper Fascia
Replacement (Short Body) on page 353.
Radiator Upper Grille Upper Insert (Qty: 2)
1
Procedure
Release the locking tabs securing the insert to the radiator upper grille assembly.
2-28
Exterior Trim
1872808
Component Name
Preliminary Procedures
1. Open either the driver or passenger door to assist in removal of the lower door molding.
2. Remove the 2 front side door lower molding nuts securing the molding to the inner door.
Lower Door Molding Locator Bolt/Pin (Qty: 2)
1
Procedure
1. Align the outer pins to the door.
2. Align the retainers and apply pressure to the exterior lower door molding to seat.
3. Install the front side door lower molding nuts and finger tighten.
Lower Door Molding Retainer (Qty: 15)
Procedure
Release the lower retainers working upward on the molding.
Lower Door Molding Assembly
Tip: Ensure the door is in the closed position prior to installing the lower molding to the door.
Exterior Trim
2-29
2244095
Component Name
Preliminary Procedure
Open either the driver or passenger front door to assist in the removal of the front lower door molding nut.
Front Side Door Lower Molding Nut
1
Procedure
Remove the front side door lower molding nut from the inner door flange.
Front Side Door Lower Molding Retainer (Qty: 13)
Procedure
Release the lower retainers from the lower door using a trim-type release tool.
Front Side Door Lower Molding Assembly
Procedure
1. Ensure the door is in the closed position prior to installing the front side door lower molding.
2. Use palm pressure to seat the retainers to the lower door.
3. Open the door and secure the lower molding nut.
2-30
Exterior Trim
Front and Rear Side Door Opening Frame Reveal Molding Replacement
Object-ID=2242764 Owner=jforce01 LMD=03-mar-2009 LMB=jforce01
1874622
Front and Rear Side Door Opening Frame Reveal Molding Replacement
Callout
Component Name
Preliminary Procedures
1. Open the front door on the side the front and rear side door opening frame reveal molding assembly is being removed from.
2. Remove the front and rear side door opening frame reveal molding lower screw.
3. Working from front to rear, release the integral retainers securing the reveal molding to the body.
Front and Rear Side Door Opening Frame Reveal Molding Screw
1
Procedure
1. Upon assembly of the front and rear side door opening frame reveal molding to the body, insert the locating
boss at the rear edge of the molding to the front top side of the body, near the rear quarter window.
2. Align the retainers from the rear edge working towards the front.
3. Apply palm pressure from the rear retainer to the front retainer up to the front fender screw location.
4. Install the screw.
Exterior Trim
2-31
1874341
Component Name
Preliminary Procedures
1. Remove either the LF or RF wheelhouse liner. Refer to Front Wheelhouse Liner Replacement on page 3110.
2. Remove the inner front wheel opening molding nut.
3. Release the retainers from the wheelhouse.
4. Release the front wheel opening molding from the front edge of the lower rocker panel molding.
5. Remove the front wheel opening molding from the vehicle.
Front Fender Wheel Opening Molding Nut
Caution: Refer to Fastener Caution on page 07.
1
Tip: Loosen the rear bolt at the rear of the front bumper fascia securing the fender flange to the front bumper
fascia.
Tighten
4.0 Y (35 lb in)
2
3
2-32
Exterior Trim
2244605
Component Name
Preliminary Procedures
1. Remove either the LF or RF wheelhouse liner. Refer to Front Wheelhouse Liner Replacement on page 3110.
2. Remove the inner front wheel opening molding nut.
3. Release the retainers from the wheelhouse.
4. Release the front wheel opening molding from the front edge of the lower rocker panel molding.
5. Remove the front wheel opening molding from the vehicle.
Front Fender Wheel Opening Molding Nut
Caution: Refer to Fastener Caution on page 07.
1
Tip: Loosen the bolt at the rear inside of the front bumper fascia securing the fender flange to the front bumper
fascia.
Tighten
2.0 Y (18 lb in)
Procedure
Detach the bottom edge of the front fender wheel opening molding from the lower front rocker panel molding tabs
and remove.
Exterior Trim
2-33
1875450
Component Name
Preliminary Procedure
Open the rear liftgate in order to access the outer lower retainer nuts.
2-34
Exterior Trim
2449631
Component Name
Preliminary Procedure
Remove the lower radiator grille. Refer to Radiator Lower Grille Replacement (Long Body) on page 223 or Radiator Lower Grille
Replacement (Short Body) on page 224.
Lower Radiator Grille Molding
1
Procedure
Release the upper bumper fascia tabs from the lower radiator grille molding assembly and remove.
Exterior Trim
2-35
1872806
Component Name
Preliminary Procedures
1. Open either the LR or RR door assembly to assist with the removal process.
2. Remove the 1 rear side door lower front molding nut securing the molding to the inner door.
Lower Door Molding Locator Pin
1
Procedure
1. Align the front pin to the door.
2. Align the retainers and apply pressure to secure the molding to the lower door.
3. Install the rear door lower molding nut and finger tighten.
Lower Door Molding Retainer (Qty: 10)
Procedure
Release the lower retainers working upward on the molding.
Lower Door Molding Assembly
Tip: Ensure the door is in the closed position prior to installing the lower molding to the door.
2-36
Exterior Trim
2244093
Component Name
Preliminary Procedures
1. Open either the LR or RR door assembly to assist with the molding removal process.
2. Remove the rear side door lower rear molding nut securing the molding to the inner door flange.
Rear Side Door Lower Molding Nut
1
Procedure
1. Align the front pin to the door.
2. Align the retainers and apply pressure to secure the molding to the lower door.
3. Install the rear door lower molding nut and finger tighten.
Rear Side Door Lower Molding Retainer (Qty: 13)
Procedure
Release the lower retainers followed by the upper door retainers.
Rear Side Door Lower Molding Assembly
Procedure
1. Ensure the door is in the closed position prior to installing the lower molding to the door.
2. Using palm pressure, secure the molding to the rear door.
3. Open the rear door and secure the rear side door lower molding nut.
Exterior Trim
2-37
1874342
Component Name
Preliminary Procedures
1. Remove the rear wheelhouse liner. Refer to Rear Wheelhouse Panel Liner Replacement on page 3111.
2. Remove the inner rear wheel opening molding nut.
3. Release the retainers from the wheelhouse.
4. Release the rear wheel opening molding from the rear edge of the lower rocker panel molding.
5. Remove the rear wheel opening molding from the vehicle.
Rear Wheel Opening Nut
1
2-38
Exterior Trim
2244090
Component Name
Preliminary Procedures
1. Remove the rear wheelhouse liner. Refer to Rear Wheelhouse Panel Liner Replacement on page 3111.
2. Remove the inner rear bumper fascia bracket, forward screw.
3. Release the retainers from the wheel opening molding.
4. Remove the rear wheel opening molding from the vehicle.
1
Exterior Trim
2-39
1872827
Component Name
Preliminary Procedure
Open the bodyside doors on the side the lower rocker moldings will be serviced from.
Procedure
Release the 7 lower retainers first followed by the 11 upper retainers.
2-40
Exterior Trim
2244452
Component Name
Preliminary Procedures
1. Open the bodyside doors on the side the lower rocker molding will be serviced from.
2. Remove the front splash guard if equipped. Refer to Splash Guard Replacement - Front (Long Body) on page 215.
Rocker Panel Molding Retainer Lower (Qty: 5)
1
Procedure
Release the 5 lower retainers using a trim-type release tool.
Rocker Panel Molding Retainer Upper (Qty: 7)
Procedure
Release the 7 upper retainers using a trim-type release tool.
Rocker Panel Molding Assembly
Tip: Detach the two locking tabs on the forward portion of the rocker molding from the lower edge of the front
fender wheel opening molding.
Exterior Trim
2-41
2244606
Component Name
Preliminary Procedures
1. Open the rear bodyside doors on the side the lower rocker molding will be serviced from.
2. Remove the rear splash guard if equipped. Refer to Splash Guard Replacement - Rear (Long Body) on page 216.
Rocker Panel Molding Retainer Lower (Qty: 4)
1
Procedure
Release the 4 lower retainers using a trim-type release tool.
Rocker Panel Molding Retainer Upper (Qty: 5)
Procedure
Release the 5 upper retainers using a trim-type release tool.
Rocker Panel Molding Assembly
Tip: Remove the lower rocker molding from the bodyside outer panel.
2-42
Exterior Trim
1878330
Component Name
Roof Panel Exterior Molding
Procedure
1. Remove the roof panel exterior molding starting at the rear of the vehicle.
2. Release the six molding retainers from the body panel.
3. Upon installation, position the front end of the molding over the forward body panel stud.
4. Position the molding by aligning the other 6 retainers to the body panel studs.
5. Secure the molding working from the front edge to the rear by pressing firmly the molding retainers onto the
body panel studs.