Академический Документы
Профессиональный Документы
Культура Документы
Tugas No.
Topik :
Nama :
Isandre Fajarrachman
NRP
F451140041
Tanggal selesai :
1 April 2015
Log
Grading
Logs
Peeling &
Cripping
Debarking &
Bucking
Glue Spreading
Drying
Lay Up
Packing
Plywood
apllication
Scheme 1.1 Simple Scheme of plywood production in Indonesia. Source : International Tropical Timber Organization
(ITTO, March 2014)
Plywood uses as building & transportation construction : paneling, sheating material, floor,
sidding, plyform, (massijaya, 2006) .In environmental issue, such as pressing, drying , and sorting
process, it has biggest emissions that affect the environment. Consumption energy for making
plywood has also big affect to environment too. Environmental problems will be reviewed is Global
Warming Potential(GWP) increase carbon gases made of warming effect on the earth, Acidification
Potential (AP) transformation of air pollutants such as sulphur dioxide and nitrogen dioxide into acids,
Eutrophication Potential (EP) it accelerates the growth of algae that may cause a reduction of oxygen,
Ozone Depletion Potential (ODP) due to CFCs and Nitrogen oxides, Photochemical Ozone Creation
Potential (POCP) summer smog which damage vegetation and material.
Inventory Analysis
In material analyze, observation taken three Indonesia plywood company. In 12 month, the
data taken and calculated for supporting material data and energy in one-cubic meter
Monthly log
Input
Monthly plywood
production
Co-products
Units
m3
A
11,322
Company
B
15,314
C
21,164
m3
6,702
10,495
11,249
Blockboard Veneer
Blockboard,
lamineboard
Electicity
National grid
Co-generation
Coal power plant
Blackboard, veneer
Tabel 1.1 log input and type company. Source : ITTO, profiles of Indonesia plywood companes (2014)
Avereging log input amount 12.707m3/month, then for LCI basic material and water quantity needed
in one cubic meter plywood production :
Input Raw
Material/log
Resin : Urea
kg
formaldehyde
Hardener
kg
Energy/Water
kWH
Electricity-grid
Electricity co- kWH
generation
Electricity coal
kg
Diesel
Liter
1,69
Company
B
1,46
134
103
73
17
0.61
11
769
10
0.167
,,49
0,135
1,40
0,130
0,941
m3
7,69
5,72
0,00
Water (municipal)
m3
0,57
0,34
1,23
Units
m3
C
1,88
Tabel 1.2 LCI inputs to produce a unit (one cubic meter). Source : ITTO (2014)
Gained average material & energy consume in one cubic meter plywood, using 1,6m3 log, resin
103,3kg, hardener 12,7kg, coal 41 kg, diesel 0,402 liter, water (river) 4,47m3, and water (municipal)
0,713m3. For material released to environment in plywood production. Emissions, solid waste, liquid
waste, and air waste.
Impact Indicator
Characterization Model
Impact Category
Global warming
Ozone depletion
Acidification
Photochemical smog
Eutrophication
Each impact indicator is a measure of an aspect of a potential impact. This LCIA does not make value
judgments about the impact indicators, meaning that no single indicator is given more or less value
than any of the others. Additionally, each impact indicator value is stated in units that are not
comparable.
Impact categories
Global Warming
Potential (GWP)
Adification
Potential (AP)
Eutrofication
Potential (EP)
Ozone Depletion
Potential (ODP)
Photochemical
Ozone Creation
Potential (POCP)
Unit
Kg CO2 Equiv.
592
Company
B
485
Kg SO2 Equiv
1.7
1.35
2.08
0,197
0,333
6,74x10-9
1,84x10-8
0,147
0,250
Kg
Phosphate 0,253
(PO4) Equiv
Kg
CFC11- 8,95x10-9
Equiv
Kg Ethylene 0,188
Equiv
C
411
Tabel 1.3 Environmental Impact for the production 1m3 plywood production. Source : ITTO, 2014
Environmental impact result averagely production from one cubic meter plywood is GWP 446kgCO2-Equiv, AP 1,91 kg SO2-Equiv, 0,311kg (PO4)-Equiv, ODP 1,40x10-8kg CFC11-Equiv and POCP
0,233kg Ethylene-Equiv. Company A had higher carbon emission because 30% of electricity are
came from coal. This comparison companies chart :
Global Warming
Potential (GWP)
200
0
Company A
Company B
Company C
1
0.5
0
Company A
Company B
Company C
Eutrofication
Potentital (EP)
0.1
0
Company A
Company B
Company C
Ozone Depeletion
Potential (ODP)
0.0000005
0
Company A Company B Company C
0.1
0
Company A Company B Company C
In this study, the global warming potential (GWP) was strongly related to use of fossil fuel
and electricity. Generally, the GWP increased with increased use of electricity from national grid for
companies C. However, the CO2 emissions for companies A nd B were a few folds higher as these
companies generated electricity from coal. The efficiency for coal generated electricity was about
30%. Companies using coal for process heat and generation of electricity should consider using
biogenic fuel as they are close to waste wood or biomass resources. For other environmental impact,
the lower consumption of diesel per unit production had led to lower EP, AP, ODP and POCP.
The plywood manufacturing process has some onsite emissions from drying veneers and
pressing the panels with the resins. These emissions were reported by the mills in the surveys. Of the
total CO2 emissions, both biogenic and fossil, 69 percent were biogenic based emissions from the
combustion of wood fuel. Carbon footprints for products or service are the greenhouse gas (GHG)
emissions associated with the manufacturing of product or delivery of a service. It is normally
reported in CO2-equiv. Respectively the CO2 emissions associated with ply wood production, logs
and resin used. The formaldehyde resin contributed a high percentage towards the overall CO2
emissions for the plywood.
Interpretation
The last step in LCA is interpretation, before going to do an a action and decision .
-
Plywood production uses many coal energy, it release large energy and emission, changing coal
energy to other can saving more energy and emission will be reduce. (using hydro-electric energy
there is no emissions generated when converting moving water to energy).
Improve material flow in the manufacturing process to reduce iternal transportation
Increase use of renewable biomass would further reduce the overall use of fossil energy and the
GWP impact from industry.
Icenaration of plywood(depleted age) can cause higher impacts of acidification and
eutrophication than other products, although thermal energy can be recovered.
Resin usage contributes to the differences in magnitude of inventory analysis and impact
assessment . Phenolformalyde is created through the refining of natural gas dan petroleum.
These machine centers contributed the most large energy, the hot pressing machine center had
the greatest environment impact because of the energy consumption and resin usage. This impact
is most evident in the fossil fuel and climate change.
Using bark as fuel source, proves benefiting to the environment. Because fossil fuels for energy
and all emissions associated with generating energy.
Referensi :
Apri H. Iswanto (2008)Kayu Lapis (Plywood) , USU e-Repository
Iwan Risnasari (2008)Pengaruh Penyusunan dan Jumlah Lapisan Vinir Terhadap Stabilitas Dimensi
Kayu Lapis(Plywood) , USU e-Repository.
Metya T. Cahya (2011)Pengembangan Kayu Lapis Berkualitas Tinggi yang Ramah Lingkungan ,
IPB Repistory
Gan K.S & M.Y Massijaya, (2013)Cradle to Gate Lofe Cycle Assessment of Softwood Plywood
Production from the Pacific Northwest , CORRIM, (1), 1-34.
Maureen P, Elaine O, & James W, Leonard J, (2014)Life Cycle Assessment for Environmental
Product Declaration of Tropical Plywood Production in Malaysia and Indonesia , ITTO, (1), 2 -28.
Sujatha D, Pandey C, & Nath S.K, (2014)Impact of Forestry Products on Climate Change Mitigation
in India , International Journal of Applied Science and Technology, (4),1-6
Effendi Arsad, (2000)Sifat Fisik Kayu Lapis Berbahan Baku Kayu Akasia (Acacia mangium Willd.)
dan Kelampayan (Anthocephalus spp.) , Jurnal Riset Industri Hasil Hutan, vol.3, 1 -8
EPA, (2004)Regulatory Impact Analysis for the Plywood and Composite Wood Products NESHAP
, Final Report EPA, (1)
Riza R., Mariah U, (2013)Kayu Lapis Struktural (Structural Plywood) , USU, (1)
Charles J.Ferari, (2000)Life Cycle Assessment Environmental Modelling of Plywood and Laminated
Veneer Lumber Manufacturing , Oregon State University, (1)
Frank W., Klaus R., (2007)Wood Building Products in Comparative LCA, Int J LCA , vol. 12, 470
- 479