Академический Документы
Профессиональный Документы
Культура Документы
JDS-S4R
Model : JDS-S4R
EQUIPMENT MANUAL
Fax: +82.2.3397.7088
www.jdsol.co.kr
www.jdsol.co.kr
Version 1.4
JDS-S4R
Note
This manual details the main function and warnings to ensure operator safety and support proper machine operation, so please
read this manual carefully and use the machine properly.
CAUTION
Please make sure of the power connection before turning the machine on.
Please do not install the equipment near a heater or power equipment. The installation site should be well
ventilated.
Please prevent overload in the power cord or extension cable as overload can cause a fire.
Please use the equipment in a workable temperature, humidity, and power range.
Please do not put the equipment on an unstable surface, tri-pod, shelf, or table.
Please do not attach any objects that are not recommended.
Installation and construction must be done by a professional technician (or equivalent trained person) following
safety regulations.
WARNING SIGNS
Warning sign for risk of electric shock.
www.jdsol.co.kr
Version 1.4
JDS-S4R
CAUTION
It can cause serious hearing damage if the person Stands within 10m in front of the speaker during operation.
Hearing damage can occur during operation if sound source of over 120dB is used for operation..
Operator should wear earplugs during manual operation.
Earplugs are effective for sound attenuation at an average of 20dB-25dB.
eight hours
95 dB SPL
four hours
100 dB SPL
two hours
105 dB SPL
one hour
110 dB SPL
30 minutes
120 dB SPL
www.jdsol.co.kr
JDS-S4R
Version 1.4
CONTENTS
1. General Information -----------------------------------------------------------------------------------------------------------------1-1) Introduction -------------------------------------------------------------------------------------------------------------------1-2) Features -----------------------------------------------------------------------------------------------------------------------1-3) Product Constructions --------------------------------------------------------------------------------------------------------1-4) Spare Parts --------------------------------------------------------------------------------------------------------------------1-5) System Diagram -------------------------------------------------------------------------------------------------------------2. Install Manual -----------------------------------------------------------------------------------------------------------------------2-1) Installation -----------------------------------------------------------------------------------------------------------------------2-1-1) JDS-S4R ---------------------------------------------------------------------------------------------------------------------2-1-2) Display Monitor ------------------------------------------------------------------------------------------------------------2-1-3) Control PC ------------------------------------------------------------------------------------------------------------------2-1-4) System Controller ----------------------------------------------------------------------------------------------------------2-2) System setup --------------------------------------------------------------------------------------------------------------------2-2-1) Network address setup for the devices -----------------------------------------------------------------------------------2-2-2) Control Application Option setup -----------------------------------------------------------------------------------------2-2-3) Communication state check -----------------------------------------------------------------------------------------------2-2-4) Basic operation state check ------------------------------------------------------------------------------------------------2-2-5) General checklist -----------------------------------------------------------------------------------------------------------2-2-6) System setup and checklist ------------------------------------------------------------------------------------------------2-2-7) Network Configuration ----------------------------------------------------------------------------------------------------3. Instruction Manual ------------------------------------------------------------------------------------------------------------------3-1) Control panel --------------------------------------------------------------------------------------------------------------------3-2) Software operation -------------------------------------------------------------------------------------------------------------3-2-1) Camera image display -----------------------------------------------------------------------------------------------------3-2-2) Connection status display -------------------------------------------------------------------------------------------------3-2-3) Radar information display -------------------------------------------------------------------------------------------------3-2-4) Controller -------------------------------------------------------------------------------------------------------------------3-3) Manual operation ---------------------------------------------------------------------------------------------------------------3-4) Technical Materials---------------------------------------------------------------------------------------------------------------3-4-1) JDS-S4R Speaker & Amp --------------------------------------------------------------------------------------------------3-4-2) Pan/Tilt ---------------------------------------------------------------------------------------------------------------------3-4-3) Video unit ------------------------------------------------------------------------------------------------------------------3-4-4) Display monitor ------------------------------------------------------------------------------------------------------------3-4-5) Control PC ------------------------------------------------------------------------------------------------------------------3-4-6) System Controller -----------------------------------------------------------------------------------------------------------
www.jdsol.co.kr
JDS-S4R
Version 1.4
4. Troubleshooting Manual -------------------------------------------------------------------------------------------------4-1) Controller -------------------------------------------------------------------------------------------------------------4-1-1) Malfunction in Pan/Tilt with joystick ---------------------------------------------------------------------------4-1-2) Malfunction in Camera Zoom with joystick --------------------------------------------------------------------4-1-3) Malfunction in controllers key --------------------------------------------------------------------------------4-2) Control PC & Software -----------------------------------------------------------------------------------------------4-2-1) PC power non operate ------------------------------------------------------------------------------------------4-2-2) Strange Phenomenon or invisible situation in camera --------------------------------------------------------4-3) Sound -----------------------------------------------------------------------------------------------------------------4-3-1) Malfunction in button Broadcast(sound source) -------------------------------------------------------------4-3-2) Malfunction in button Broadcast(MIC) -----------------------------------------------------------------------4-3-3) Amplifier malfunction diagnosis --------------------------------------------------------------------------------4-4) Laser Diode -----------------------------------------------------------------------------------------------------------4-4-1) Malfunction in Laser Diode by using controller ---------------------------------------------------------------4-5) CCD Camera ---------------------------------------------------------------------------------------------------------4-5-1) CCD Camera malfunction diagnosis ---------------------------------------------------------------------------4-6) Pan/Tilt ----------------------------------------------------------------------------------------------------------------4-6-1) Malfunction in Pan/Tilt by using Controller -------------------------------------------------------------------4-6-2) Pan/Tilt malfunction diagnosis ----------------------------------------------------------------------------------5. Replacement ---------------------------------------------------------------------------------------------------------------5-1) Compress driver replacement----------------------------------------------------------------------------------------5-2) Video unit replacement ----------------------------------------------------------------------------------------------5-2-1) Power Board SMPS replacement -----------------------------------------------------------------------------5-2-2) Video Encoder replacement ------------------------------------------------------------------------------------5-2-3) Serial to Ethernet serial converter(RS 422, RS485) replacement ---------------------------------------------5-3) Speaker cable and camera cable replacement ----------------------------------------------------------------------5-4) Controller replacement -----------------------------------------------------------------------------------------------6. Warranty --------------------------------------------------------------------------------------------------------------------
www.jdsol.co.kr
Version 1.4
JDS-S4R
1. GENERAL INFORMATION
1-1 Product Introduction
Directional sound wave transmitter
A directional sound wave transmitter is the broadcasting equipment for long distances of more than1kmand the maximum
output is Max. 154dBA at 1min front of the equipment.(dBA means A-weighted decibels).
SPL vs Distance
160
150
140
130
120
110
100
90
80
500
1000
1500
Distance(m)
2000
2500
3000
Compress driver is a converter and a kind of loud speaker that converts electrical signals to sound.
www.jdsol.co.kr
JDS-S4R
Version 1.4
The system is constructed with radar, camera, data analysis software, directional acoustic hailing device and controller for effective
detection and defense against dangerous vessel on the sea. Each piece of equipment provides individual functions as follows:
Radar: Detection of the object on the sea
Camera: Video recording or watching the detected object by radar
Data analysis software: Analyzes movement of the object to compare with dangerous vessel movement patterns and identifies
the object as to whether it is danger or not.
Directional acoustic hailing device: Gives a warning broadcast if the detected object is identified as a dangerous vessel. And, it
provides a sound wave attack when dangerous vessel closely approaches the vessel.
Controller: Provides remote control function for the entire system.
www.jdsol.co.kr
Version 1.4
JDS-S4R
Rated Voltage:
AC 220V, 60 Hz
Model:
JDS-S4R
Manufacturer:
JD SOLUTION CO.,LTD.
Country of origin:
Republic of Korea
Vendor:
JD SOLUTION CO.,LTD.
+82 1577-1435
Features
High-powered sound
- Maximum SPL 154dB @ 1 meter and accurate message delivering up to 1,500-3,000 meters.
* Damping ratio for SPL by distance can have very different actual dB levels depending on temperature, humidity, winddirection / speed, time, and season.
High directivity sound radiation
- Sound radiation at15 degrees from use of the high directional sound delivery tube.
- Minimizes noise damage for the operator through sound reduction at the side and rear of the machine.
Third party equipment integration
- Third party equipment integration and remote control available. (Radar, laser and water cannon)
Object detection capability
- Accurate detection of target object through high-performance 43X zoom camera.
- Object detection at night through LD(Laser Diode)
- Situation analysis and verification through video recording.
Convenient to use
- Up/down, left/right movement control through joystick on the controller.
- Automatic or manual operation modes can be selected..
- MP3, Computer, Audio equipment connection supported through external audio input under manual operation mode.
High durability structure
- No failure or degradation by seawater or rain due to a double reflecting structure..
- Strong durability against any external shock due to the high strength of the compress driver.
BIT(Built-in Test)
Self-inspection of compress drivers through amplifier power switch ON or manual BIT switch.
www.jdsol.co.kr
Version 1.4
JDS-S4R
Name
JDS-S4R
Model no
Specification
Amount
JDS-AHD-S4A-T2
2 set
2,400w
Pan/Tilt
JDS-AHD-PTZ-T2
2 set
PTZ Controller
SMPS
AC 220V, MAX300W
Video unit
JDS-AHD-VU-T2H2
2 set
CCTV
Laser Diode
Video Encoder
HUB
SMPS
Serial to Ethernet
Display monitor
JDS-AHD-DPU-T2
1 set
Control PC & OS
JDS-AHD-SST-T2
1 set
System Controller
JDS-AHD-OPU-T2
JDS-W-PTZ/S4A-1
JDS-W-PTZ/S4A-2
JDS-W-PTZ/SST
JDS-W-SST/DPU
JDS-W-PTZ/PO
JDS-W-SST/PO
JDS-W-OPU/PO
JDS-W-DPU/PO
JDS-W-RA/HB
1 set
1 set
www.jdsol.co.kr
Version 1.4
JDS-S4R
Article
Amount
P/N
COMPRESS DRIVER
6 EA
14010005
1 SET
14000001
1 ASSY
14000002
1 ASSY
14030005
2 ASSY
14030006
1 ASSY
14030007
JDS-W-PTZ/S4A-1
SPEAKER CABLE
1 ASSY
12030006
JDS-W-PTZ/S4A-2
CAMERA CABLE
1 ASSY
12030007
MICROPHONE
2 EA
14010015
10
5 EA
12030008
11
VU BASE O RING
5 EA
12030009
12
PROTECTION COVER
2 EA
13030001
13
6 EA
14010008
14
LINE-IN CABLE
2 EA
14010013
15
EAR PLUG
5 EA
13020006
16
4 EA
13030004
17
Tapping screw
sts M2-10L
6 EA
10050006
18
sts M3-10L
4 EA
10020003
19
Wrench bolt
sts M3-10L
18 EA
10010006
20
sts M3-8L
4 EA
10030003
21
sts M4-16L
4 EA
10100001
22
Hex bolt
sts M4-20L
3 EA
10090001
23
Wrench bolt
sts M4-20L
18 EA
10010005
24
Wrench bolt
sts M4-30L
18 EA
10010007
25
sts ,M5-50L
4 EA
10030004
26
Wrench bolt
sts M5-10L
4 EA
10010008
27
Wrench bolt
sts M10-20L
6 EA
10010009
28
Hex bolt
sts M10-55L
8 EA
10090002
29
Nut
sts M4
4 EA
10060005
30
Nut
sts M5
4 EA
10060001
31
Nut
sts M10
8 EA
10060006
32
Support nut
M3-15L
4 EA
10110001
33
Washer
sts M3
4 EA
10070006
10
Etc.
www.jdsol.co.kr
Version 1.4
JDS-S4R
34
Washer
sts M4
43 EA
10070001
35
Washer
sts M5
8 EA
10070002
36
Washer
sts M10
14 EA
10070008
37
Spring Washer
sts M3
8 EA
10080006
38
Spring Washer
sts M4
43 EA
10080001
39
Spring Washer
sts M5
8 EA
10080002
40
Spring Washer
sts M10
14 EA
10080008
11
www.jdsol.co.kr
Version 1.4
JDS-S4R
Radar
Bridge
Integration
Remote Monitoring & Control
Rescue Signal
JDS-S4R
12
JDS-S4R
www.jdsol.co.kr
JDS-S4R
Version 1.4
13
www.jdsol.co.kr
Version 1.4
JDS-S4R
2. Installation Manual
2-1 Install
2-1-1 JDS-S4R
Move the equipment to the installation site and remove the packaging and
plastic covers.
Check the mounting base for the installation site, power and communication
cable connection.
Align the crane hooks to eye bolts that are placed on both sides of the
JDS-S4R and lift the equipment.
Adjust mounting base hole with mounting hole of the JDS-S4R.
Fix the 10 mounting holes with bolt M10.
Connect the power cable and communication cables.
CAUTION
The workers should observe all safety regulations and wear safety equipment during installation
Please make sure of the connection between the eye bolts and hooks and belt(chain) for crane operation
The equipments weight is around 150kg, so please do not approach the crane working area while crane is
rotating or moving.
CAUTION
Power should be OFF before connecting the cables to the equipment.
14
www.jdsol.co.kr
JDS-S4R
Version 1.4
2-1-3 Control PC
15
www.jdsol.co.kr
JDS-S4R
Version 1.4
16
www.jdsol.co.kr
Version 1.4
JDS-S4R
Refer to the AXIS IP Utility Application provided by AXIS for video encoder setup.
Activate the application and then the application will automatically search the encoder, which is connected to internal network.
Select the encoder on the search list and double click to connect and change the video encoder setup.
Press Setup if screen displays Live view for selected encoder.
If system requires an ID and Password to be input, enter the default ID and Password to go to the next step.
(Default ID: root, Password: jdsol)
On the setup display, select Basic Setup -> TCP/IP and set the values for IP address, Subnet mask, and Default
router depending on installation environment.
17
www.jdsol.co.kr
JDS-S4R
Version 1.4
Use ezManager.exe application that is provided by SOLLAE SYSTEM to change or set the values for Serial to Ethernet converter.
User will see the screen display as in the above picture, then click the Search All button in the red box to search the
convertor that is connected to the internal network.
On the searched list, please select the converter and double click to change the set up.
Select the Network tab and set the values for IP address, Subnet mask, and Default router.
18
www.jdsol.co.kr
Version 1.4
JDS-S4R
Set the properties for integrated radar and the radar screen that will be displayed on the Control Application.
(Radar information, X_Band, S_Band communication, Radar connection port, and data transfer rate are included in the setup
menu.)
Info->Maker: Maker of integrated radar
Info->Model: Model of integrated radar
Communication ->X_BandUse:Data use for X_Band Radar
Communication ->X_BandPort1: X_Band Radar connection port
Communication ->X_BandPort2: X_Band Radar connection port (Spare)
Communication ->X_BandBaudrate: X_Band Radar data transfer speed
Communication ->S_BandUse: Data use for S_Band
Communication ->S_BandPort1: S_Band Radar connection port
Communication ->S_BandPort2: S_Band Radar connection port (Spare)
Communication ->S_BandBaudrate: S_Band Radar data transfer speed
Zoom Min/Max -> Zoom Min: Minimum value of the distance display for Radar (Unit:NM)
Zoom Min/Max -> Zoom Max: Maximum value of the distance display for Radar (Unit:NM)
Color of Object ->Stop_Object: The color of the stopped object on the Radar
Color of Object ->Moving_Object: The color of the moving object on the Radar
Color of Object ->Suspect_Object: The color of the suspected object on the Radar
Color of Object ->Dangerous_Object: he color of the dangerous object on the Radar
Distance of Limit_Range -> Recognition Range: Recognition/Tracking range (Unit:NM)
Distance of Limit_Range -> Warning Range: Warning broadcast range (Unit:NM)
Distance of Limit_Range -> Attack Range: Attack broadcast range (Unit:NM)
Color of Range-> Recognition Range: The color of the recognition/tracking range
Color of Range-> Warning Range: The color of the warning broadcast range
Color of Range-> Attack Range: The color of the attack broadcast range
Disappeared Object->MaxDist: If object is not within pre-defined distance, recognize the object as disappeared (Unit:NM)
Disappeared Object->Sustainment_time: If there is no data input signal for the target in a pre-defined time, recognize the object
as disappeared (Unit:Second)
Disappeared Object->Notification_time: Display the target disappearance location for pre-defined time
19
www.jdsol.co.kr
JDS-S4R
Version 1.4
20
www.jdsol.co.kr
JDS-S4R
Version 1.4
Location of Installation for Tilt ->Height of Installation: Enter the height of equipment(JDS-S4R) installation site from the
surface of the sea for automatic tilt angle movement calculation by approaching distance to own ship in case of object
tracking. (Refer to the picture on next page.)
Resolution ->value: Enter the Resolution for Pan/Tilt device
Angle, velocity and resolution are the specifications for Pan/Tilt and there is no need to change each value. (Even if the
values change, operation does not change.)
21
www.jdsol.co.kr
JDS-S4R
Version 1.4
Max Volume Setting-> Normal max: Maximum volume value for normal operation
Max Volume Setting-> Warning max: Maximum volume value for warning broadcast
Max Volume Setting-> Attack max: Maximum volume value for attack broadcast
Max Volume Setting->Manual max: Maximum volume value for manual operation
Sound Management: Sound source management for Preset (Sound source insert/delete)
F1 -F8: Able to preset the sound sources for each function key to support immediate sound change in case of emergency or
manual operation(Warning message or foreign language sound source)
Warning: Default sound source setup for warning broadcasting
Attack: Sound source setup for attack broadcasting
22
www.jdsol.co.kr
Version 1.4
JDS-S4R
2-2-3-2 Main H/W connection check (AMP, Pan/Tilt, CCD Camera, Laser Diode)
It is possible to check the status of each device with the text color on the Control Application (Red: disconnected, Green:
connected)
AP : Amplifier
PT : Pan/Tilt
CC : CCD Camera
LD : Laser Diode
23
www.jdsol.co.kr
Version 1.4
JDS-S4R
24
www.jdsol.co.kr
JDS-S4R
Version 1.4
25
www.jdsol.co.kr
Version 1.4
JDS-S4R
STBD DEVICES
PORT DEVICES
Video Encoder
Video Encoder
Username
root
root
Password
Jdsol
Password
Jdsol
IP Address
192.168.1.151
IP Address
192.168.1.152
Subnet Mask
255.255.255.0
Subnet Mask
255.255.255.0
Gateway
192.168.1.1
Gateway
192.168.1.1
Video Format
MJPEG
Video Format
MJPEG
Resolution
704 X 480
Resolution
704 X 480
Serial Converter
Serial Converter
Type
RS-485
Type
RS-485
Baud rate
19200
Baud rate
19200
IP Address
192.168.1.153
IP Address
192.168.1.156
Subnet Mask
255.255.255.0
Subnet Mask
255.255.255.0
Gateway
192.168.1.1
Gateway
192.168.1.1
Serial Converter
Serial Converter
Type
RS-422
Type
RS-422
Baud rate
19200
Baud rate
19200
IP Address
192.168.1.155
IP Address
192.168.1.157
Subnet Mask
255.255.255.0
Subnet Mask
255.255.255.0
Gateway
192.168.1.1
Gateway
192.168.1.1
Serial Converter
Serial Converter
26
Username
Type
RS-422
Type
RS-422
Baud rate
115200
Baud rate
115200
IP Address
192.168.1.154
IP Address
192.168.1.158
Subnet Mask
255.255.255.0
Subnet Mask
255.255.255.0
Gateway
192.168.1.1
Gateway
192.168.1.1
www.jdsol.co.kr
JDS-S4R
Version 1.4
3. INSTRUCTION MANUAL
3-1. Control panel
Control panel
Power
[POWER] : Control PC power On/Off
Sound Function
A sound source could be set-up beforehand depending on the situation and languages, and it can be changed as necessary
[SOUND1] : Button for setting up sound source as No.1
[SOUND2] : Button for setting up sound source as No.2
[SOUND3] : Button for setting up sound source as No.3
[SOUND4] : Button for setting up sound source as No.4
27
www.jdsol.co.kr
Version 1.4
JDS-S4R
control all the devices (Joystick, Button, Track-ball Mouse).
The options are switched by Selector Switch. All the control devices (Pan/Tilt, Camera, Laser Diode, Speaker Volume, and
other devices that the operator can control) can be controlled manually under manual mode. Limited functions such as
camera, Laser Diode, and sound source can be controlled under automatic mode.
Conversion of PORT/STBD
As JDS-S4Rs are installed on PORT and STBD, operator can select the device by Selector Switch for operation.
SYSTEM
[System Chk] : To switch display mode on Graphic LCD. The information will display present operation mode or
connection status for each device.
[Alarm Log] : To check the log saved on the disk regarding system errors, device problems and other issues.
[Broadcast] : To play and stop the broadcasting or playing of sound source.
LASER
Button to control Laser Diode to identify the object at night
[Beam Width +] : Extension of laser width
[Beam Width -] : Reduction of laser width
[Brightness +] : Increase laser brightness
[Brightness -] : Decrease laser brightness
Direct exposure of Laser Diode to be dangerous and it must be used with caution.
* It is not able to be used with thermal camera
28
www.jdsol.co.kr
JDS-S4R
Version 1.4
ALARM
[BUZZER]: To give notification to the operator if any alarm occurs
[Alarm Ack]: To stop the buzzer
[Lamp Test]: To check LED conditions; if operator pushes this button, all LED on the buttons are off.
[Alarm Test]: To test the buzzer. Push this button to test Buzzer function.
Joystick
Control Pan/Tilt by moving Joystick up/down/ left/right, and control zoom in/out by turning the top of the joystick to left/right.
LCD Display
Display equipment operation status for user convenience. It shows the present operation mode such as Auto/Manual, Speaker
Volume/Mute, Recording, etc. and connection status of the devices. The Display can be switched by System Chk button. (Please
refer to .)
MIC Socket
Microphone socket for broadcasting.
Trackball Mouse
To efficiently control JDS-S4R
29
www.jdsol.co.kr
Version 1.4
JDS-S4R
The picture above shows the main screen display of the Control Application and the screen divided as Camera image
display, Radar display, connection status display and controller.
Recording...
Broadcasting
Recording...
Broadcasting
Section for real-time CCD Camera image display (Left: PORT, Right: STBD)
One control application can control two different JDS-S4R and the equipment should be selected to control. There will be red
right for the selected equipment to control.
Message, recording appears when camera is recording.
Message, broadcasting appears when broadcasting.
30
www.jdsol.co.kr
Version 1.4
JDS-S4R
Indicate individual network connection status for each device for PORT and STBD separately.
(RED: Disconnected, GREEN: Connected)
AP : Indicate AMP connection status.
Radar
Radar Zoom
Pan/Tilt Info.
Limit Range
3-2-3-1 Radar
Display the target with received data from main radar for own ship.
Available to zoom in/out for radar view area and set the force tracking for selected target by user.
The blue arrow indicates ships direction.
31
www.jdsol.co.kr
Version 1.4
JDS-S4R
Warning: If any object is detected in this range under automatic operation mode, system will start warning broadcast.
Attack: If any object is detected in this range under automatic operation mode, system will start attack broadcast.
3-2-4 Controller
In case of Control Panel malfunction, the equipment can be controlled through the Control Application.
Additionally, controller section indicates existing operation status.
CAUTION
It can cause serious hearing damage if the person stands within10m in front of the speaker during operation.
Hearing damage can occur during operation if sound source of over 120dB is used for operation.
Operator should wear earplugs during manual operation.
Earplugs are effective for sound attenuation at an average of 20dB-25dB.
32
www.jdsol.co.kr
JDS-S4R
Version 1.4
3-2-4-3 Auto/Manual
Auto
- Activate proper operation based on own judgment by Control Application without operators control
- Automatic device activation based on received target data for video recording and sound delivery in accordance with predefined recognition, warning, and attack range.
Manual
- To allow operator to control the system, select Manual Mode.
Operation enabled merely with AUTO/MANUAL selector switch when connected to control panel.
3-2-4-4 PORT/STBD
The direction of the equipment should be defined before use of two units of JDS-S4R in one Control Application.
Operation enabled merely with AUTO/MANUAL selector switch when connected to control panel.
3-2-4-5 Video
REC Button
- Video recording start/stop
- Recordingmessage will be displayed when video recording starts.
- After stopping the recording, the file will be saved in local disk with file name combined with recorded camera
(PORT_CCD/STBD_CCD), recording date and time.
PLAY Button
33
www.jdsol.co.kr
Version 1.4
JDS-S4R
CAUTION
The Laser of device is Class 4.
Be careful not to be exposed to laser.
Department Head must to covered at work would cover.
34
www.jdsol.co.kr
JDS-S4R
Version 1.4
3-2-4-10 Setting
Screen display for detailed properties that are required for system operation.
Refer to Control Application Option Setup for detailed explanation.
Push the CHANGE button at the lower left side and input password (default: 000) to modify setting.
Setting modification method (by using control panel mouse)
- Numerical setting value: double click on the values title and input the value using pop-up numeric pad.
-TRUE or FALSE setting value: double click on the setting value to change the state.
- Color setting value: Click on the value and push the square button that is generated and choose the color on the pop-up
color code.
Severe system operation problem may result when setting is modified without accurate understanding of the contents. Thus,
do not change the setting unless necessary. In case of modification, understand the applicable contents accurately if setting
needs modification.
35
www.jdsol.co.kr
Version 1.4
JDS-S4R
CAUTION
It can cause serious hearing damage if the person stands within 10m
in front of the speaker during operation.
Operator should wear earplugs during manual operation.
(Earplugs are effective for sound attenuation average of 20dB-25dB.)
Power Switch
If protection LED on amplifier indicates red LED continuously, turn the power off and turn on the amplifier after 30
seconds for normal operation.
36
www.jdsol.co.kr
JDS-S4R
Version 1.4
Line-In Switch
Three-step toggle switch for the line-in. Upper is for microphone input, middle is for line-in input, and bottom is for BIT
implementing.
LED display
Power LED: When turning the power on, power LED will be on and amplifier will be defaulted.
Signal level LED: The individual LED will be indicated for output level as 70%, 90%, protection when turning on the volume.
Protection LED will be turned on and off frequently if the output is at maximum level.
(LED light flicking is normal operation status)
Protection LED: If the output exceeds amp capability, protection LED will be on and amp will reboot automatically.
Drv 1 - Drv 6 LED: LEDs indicate each driver from No.1 to No.6. All driver LEDs will flicker sequentially when BIT is
implemented. LED will indicate a green color when driver works properly, but LED will display no light in case of driver
malfunction.
Volume control
Use volume knob for manual output control. Turn the knob to the left to decrease output and to the right to increase output.
Although a protection circuit is contained inside of the equipment, place the knob at minimum output when turning on/off
the equipment for safety purposes.
37
www.jdsol.co.kr
Version 1.4
JDS-S4R
PAN/TILT
(JDS-AHD-PTZ-T2)
VIDEO UNIT
(JDS-AHD-VU-T2H2)
Maximum Volume(SPL)
154dB @ 1m front(Peak)
Distance
~ 3,000m
Communication Range
Frequency Range
150Hz 5kHz
Amplifier Output
2400 Watt
15(@2kHz /-3dB)
Power Input
AC 220V 60Hz
Environment
Amp
38
MIL-STD 810G
MIL-STD 461F
Diameter : 495 X 530 X 723 (W X H X L)
Weight : (70)Kg
Operation Condition
Output
2,400W
Frequency range
20
~ 20,000Hz
www.jdsol.co.kr
Version 1.4
JDS-S4R
SNR
106 dB
Output Circuitry
2 Step class H
Input impedance
12 k
Input
Remote
RS485
Input power
AC 220V 60Hz
Weight
12Kg
Size
Operation Condition
-20 ~ 50 / 0 ~ 95%(RH)
3-4-1-2 Composition
CaseAluminum material applied to protect the internal contents of the speaker against external shock or corrosion.
HornRadiates the amplified signal as a directional sound wave to specified direction and angle.
Compress driverReleases the amplified signal from the amplifier.
Amplifier Amplifies the input signal.
39
www.jdsol.co.kr
Version 1.4
JDS-S4R
Pin No
Signal Description
Pin No
Signal Description
Pin No
24V_3
11
Audio_L-
21
24V_4
12
Audio_L+
13
Signal Description
Signal Description
31
RS485_RX
22
32
RS422_RX-(PTZ)
RS422_RTN(PTZ)
23
33
RS422_TX-(PTZ)
14
RS422_RX+(PTZ)
24
34
8(Brown)
15
RS422_TX+(PTZ)
25
35
4(Blue)
16
7(White/Brown)
26
36
6(Green)
17
5(White/Blue)
27
37
2(Orange)
18
3(White/Green)
28
19
1(White/Orange)
29
RS485_RTN
20
24V_RTN_3
30
RS485_TX
10
40
Audio_RTN
24V_RTN_4
Pin No
www.jdsol.co.kr
Version 1.4
JDS-S4R
Connector Pin Assignment
Pin No
Signal (D38999/24WE26PN)
Signal Description
Pin No
Signal Description
3 (White/Green)
1 (White/Orange)
6 (Green)
2 (Orange)
5 (White/Blue)
7 (White/Brown)
reserved
8 (Brown)
reserved
4 (Blue)
reserved
reserved
reserved
reserved
reserved
24V_RTN_3
24V_3
24V_RTN_4
24V_4
RS422_RX-
RS422_RTN
RS422_RX+
RS422_TX+
reserved
RS422_TX-
reserved
Pin No
Signal Description
Remark
AC_H1
Speaker AMP
AC_N1
Speaker AMP
F.G1
Speaker AMP
AC_N2
PTZ
AC_H2
PTZ
F.G2
PTZ
AC Power (D38999/24WE6PN)
41
www.jdsol.co.kr
Version 1.4
JDS-S4R
Pan(Azimuth)
Range[degree]
90
Velocity[degree/sec]
6 /sec
Range[degree]
175
Velocity[degree/sec]
30 /sec
Resolution[deg.]
Mechanical
Electrical
0.006
Dimension[mm]
Weight[Kg]
70Kg
Input Voltage
AC 220V
Input Power[W]
MAX 3000W
Operation Condition
3-4-2-2 Composition
Case -Aluminum material applied to protect the internal contents of the speaker against external shock or corrosion.
PTZ Controller Pan/Tilt control
SMPS Module Power supply
BLDC Motor-Up/Down, Left/Right movement
Absolute Encode
Manual ON/OFF Switch-In case of manual operation
42
www.jdsol.co.kr
JDS-S4R
Version 1.4
43
www.jdsol.co.kr
Version 1.4
JDS-S4R
Signal (D38999/24WE26PN)
Signal Description
Pin No
Signal Description
3 (White/Green)
1 (White/Orange)
6 (Green)
2 (Orange)
5 (White/Blue)
7 (White/Brown)
reserved
8 (Brown)
reserved
4 (Blue)
reserved
reserved
reserved
reserved
reserved
24V_RTN_3
24V_3
24V_RTN_4
24V_4
RS422_RX-
RS422_RTN
RS422_RX+
RS422_TX+
reserved
RS422_TX-
reserved
Signal Description
Remark
AC_H1
Speaker AMP
AC_N1
Speaker AMP
F.G1
Speaker AMP
AC_N2
PTZ
AC_H2
PTZ
F.G2
PTZ
AC Power (D38999/24WE6PN)
44
www.jdsol.co.kr
Version 1.4
JDS-S4R
Connector Pin Assignment
Pin No
Signal (D38999/24WE26PN)
45
Signal Description
Pin No
Signal Description
3 (White/Green)
1 (White/Orange)
6 (Green)
2 (Orange)
5 (White/Blue)
7 (White/Brown)
8 (Brown)
4 (Blue)
www.jdsol.co.kr
Version 1.4
JDS-S4R
Laser Diode
Video Encoder
Imaging Device
Pixels
Horizontal Resolution
Zoom
43X
S/N Ratio
Video Output
Focus Control
Auto/Manual/One shot
Communication
Power Source
Dimension(W*H*D)
Weight
1.5Kg
Operation Condition
LD distance
1Km
LD FOV
0.6~15
LD Light output
8W
Video compression
Motion JPEG
Frame rate H.264
Audio
Connectors
Operating Condition
Power
Dimension/Weight
Refer to 3-4-3-2, 3-4-3-3, CCD Camera and LD glasses are required to clean periodically. (There is no
problem in using damp rag.)
46
www.jdsol.co.kr
JDS-S4R
Version 1.4
3-4-3-2 Composition
47
www.jdsol.co.kr
Version 1.4
JDS-S4R
Pin No
Signal Description
Pin No
Signal Description
Pin No
24V_3
11
Audio_L-
21
24V_4
12
Audio_L+
13
Signal Description
Signal Description
31
RS485_RX
22
32
RS422_RX-(PTZ)
RS422_RTN(PTZ)
23
33
RS422_TX-(PTZ)
14
RS422_RX+(PTZ)
24
34
8(Brown)
15
RS422_TX+(PTZ)
25
35
4(Blue)
16
7(White/Brown)
26
36
6(Green)
17
5(White/Blue)
27
37
2(Orange)
18
3(White/Green)
28
19
1(White/Orange)
29
RS485_RTN
20
24V_RTN_3
30
RS485_TX
10
48
Audio_RTN
24V_RTN_4
Pin No
www.jdsol.co.kr
Version 1.4
JDS-S4R
21.5
LCD Panel
LG LM215 WF3
LED
Brightness(cd/m)
280
Viewing Angle(R/L/U/D)
89/89/89/89
Operating Temperature
0 ~ 50
3-4-4-2 Composition
49
www.jdsol.co.kr
JDS-S4R
Version 1.4
50
www.jdsol.co.kr
Version 1.4
JDS-S4R
CPU
Intel core
Main board
RAM
VGA
GeForce GTX660
HDD
Power
OS
Window 7 professional
SATA3
(x64)
3-4-5-2 Composition
51
www.jdsol.co.kr
JDS-S4R
Version 1.4
52
www.jdsol.co.kr
Version 1.4
JDS-S4R
AC220V 60Hz
Interface
Display
GLCD-240X64 Pixel
Connector
Etc
3-4-6-2 Composition
53
www.jdsol.co.kr
JDS-S4R
Version 1.4
54
www.jdsol.co.kr
Version 1.4
JDS-S4R
4. Troubleshooting Manual
4-1 Controller
4-1-1 Malfunction in Pan/Tilt with joystick
4-1-1-1 Check the joysticks recognition status.
Refer to 3-4-5-4, 3-4-6-4, loosen the Control Controller power cable (JDS-W-OPU/PO) & USB Communication
cable (JDS-W-SST/OPU) and re-connect
If the control software is implemented as rebooting the Control PC, click the X button which is located
bottom left on the screen and close the software.
As following image, click the (1) and (2) with track-ball mouse.
(2)
(1)
Check the appeared screen whether there is HF USB -> If you couldnt find HF USB, replace the Controller
in reference to 5-4 since poor recognition of joystick.
55
As under image, click the right button of mouse on the HF USB icon and click the Game controller setting
www.jdsol.co.kr
JDS-S4R
Version 1.4
If under image is appeared on the screen, check that +mark moves up down left right side by manipulating
the joystick.
56
www.jdsol.co.kr
Version 1.4
JDS-S4R
If the+ mark moves well by following joysticks movements, recognition of joystick is normal-> If it does not
move normally, that is poor condition and replace the controller by following 5-4
Refer to 2-2-1-2, implement ezManager and click Search All button. Then, Check if convertor IP is
searched about Pan/Tilt (PORT : 192.168.1.154, STBD : 192.168.1.157)
If the IP is searched, Convertor state is normal -> If it is not, replace the convertor by following 5-2-3 and
setup the new convertor by following 2-2-1-2,
2-2-7
Refer to 4-1-1-1, like under image put the HF Joystick properties screen and turn the joystick head
clockwise, counter clockwise. Check if Z Axis is changed. -> If it operates abnormally, replace the controller
by following 5-4.
Refer to 2-2-1-2, implement ezManager and click Search All button. Then, check if convertor IP is searched
about Camera (PORT : 192.168.1.153, STBD : 192.168.1.156)
57
If the IP is searched, Convertor status is normal. -> If it is not, replace the convertor by following 5-2-3 and
www.jdsol.co.kr
Version 1.4
JDS-S4R
Refer to 3-4-5-4, 3-4-6-4, loosen the Control Controller power cable (JDS-W-OPU/PO) & USB Communication
cable (JDS-W-SST/OPU) and re-connect.
If the control software is implemented, by rebooting the Control PC, click the X button which is located
bottom left on the screen and close the software. As following image, click the (1), (2), (3), (4), and implement
Notepad
(3)
(4)
(2)
(1)
58
In case of flicking the Notepad cursor, press controllers KEY and check that under letter is appeared.
www.jdsol.co.kr
Version 1.4
JDS-S4R
If the letter is appeared, Controller(Keyboard) recognition status is normal.-> If it is not appeared, that is
malfunction of controller, so replace the controller by following 5-4
4-1-3-2 Check the status of device related to key -> Refer to each devices table of contents (AMP : 4-3, Laser
Diode : 4-4)
After device power energize, it is needed about 2~3 min to check the vision. Because Video encoder needs
time to prepare in operating the server.
Refer to 2-2-1-1, check the Video encoder IP is appeared in current direction (PORT IP : 192.168.1.151, STBD
IP : 193.168.1.152) -> If the IP is not appeared, replace the Video encoder and then setup the video encoder
by following 2-2-1-1-
4-3 Sound
4-3-1 Malfunction in button Broadcast (Sound source)
4-3-1-1 Check setup regarding software sound
Check SOUND ON status as part of SOUND CONTROL in bottom right of control software -> If SOUND
OFF is appeared, press that button one more.
Check the Volume if it is 0 -> By using track-ball mouse, click the volume gauge and control the volume.
4-3-1-2 Check Select switch regarding to sound source of Controller -> Check that if MIC/SOUND PLAY switch
located top of LCD is selected to SOUND PLAY
4-3-1-3 Check Video encoder connection state -> Refer to 4-2-2-1
4-3-1-4 Check Convertor status regarding Amplifier
Refer to 2-2-1-2, implement ezManager and click Search All button. Then, check if convertor IP is searched
about amplifier (PORT : 192.168.1.153, STBD : 192.168.1.156)
If IP is searched, Convertor status is normal -> If it is not searched, replace the convertor by following 5-2-3,
set convertor up by following 2-2-1-2, 2-2-7
59
www.jdsol.co.kr
Version 1.4
JDS-S4R
If the 6 LED are turned as green with ticktack sound, amplifier & Compress driver are normal. -> If all of
LED are flickered or one of them is remained as turned off, that is notification of malfunction in compress
driver so replace compress driver following 5-1. Otherwise, if there is no response or all of LED are remained
as turned off, that is malfunction of amplifier
Connect hand-microphone provided as spare part, Check that the sound is normally releasing with clockwise
controlling the volume knob to the right.
If the sound is released, that is normal -> If it is not, that is malfunction of amplifier
If there is any strange thing through upper 2 step, select Remote/Manual switch as remote and then reboot
Through the control software, check whether the sound release and MIC broadcast is possible -> If the sound
is not normally released, that is malfunction of amplifier.
Check that it is LD ON state in the content of bottom right LD ON/OFF -> If LD OFF state is appeared,
press the button one more, then it will be changed as LD ON
Following 2-2-1-2, implement ezManager and click Search All button. Then, check if convertor IP is
searched about Laser Diode (PORT : 192.168.1.155, STBD : 192.168.1.158)
If IP is searched, Convertor state is normal -> If it is not searched, replace Convertor by following 5-2-3,
setup the Convertor by following 2-2-1-2, 2-2-7
Caution : It is needed to check if there is anyone near the device before release the laser. It is to prevent the
60
www.jdsol.co.kr
Version 1.4
JDS-S4R
Power
CCD
Board
Camera
Check that if the RED LED is turned on, under the rear of camera
Check the power supply/output to power board by using test machine, in case the power LED is not turned
on -> If there is any problem in supplying/output power, replace the power board by following 5-2-1
Check the communication & power line whether normally connected to rear of camera. -> If there is any
problem in cable, that is malfunction of camera.
4-6 Pan/Tilt
4-6-1 Malfunction in Pan/Tilt by using Controller
4-6-1-1 Check the Manual On/Off switch set as off -> If the switch is ON, please change it to OFF and restart
control software and manipulate Pan/Tilt
4-6-1-2 Even though the switch is off, Pan/Tilt manipulating is not available. -> Refer to 4-6-2
61
www.jdsol.co.kr
JDS-S4R
Version 1.4
5. Replacement
5-1 Compress driver replacement
Replace the compress driver according to the following procedures in case of compress driver malfunction.
1)
Turn off the equipment and loosen the bolt (M14, 18 pcs) with T-wrench for rear panel.
2)
After opening the rear cover, check the number of the malfunctioning driver (check driver LED on amplifier) and
disconnect the cable for defective driver.
3)
62
Replace the defective driver with a working driver and assemble the machine.
www.jdsol.co.kr
Version 1.4
JDS-S4R
4)
Compress driver and its connection cable have (+), (-) polarity. Connect proper polarity [(+) to (+) / (-) to (-)] for
compress driver and each connection cable. If a cable is connected with the wrong polarity, maximum output and voice
clearance rate will be greatly degraded.
CAUTION
Turn off the equipment before the replacement procedure.
63
www.jdsol.co.kr
Version 1.4
JDS-S4R
3) Check the part that is required to be replaced and replace the part with the following procedure
CAUTION
Turn off the equipment before the replacement procedure.
64
www.jdsol.co.kr
Version 1.4
JDS-S4R
1)
3)
2)
65
www.jdsol.co.kr
Version 1.4
JDS-S4R
66
www.jdsol.co.kr
Version 1.4
JDS-S4R
1)
Please turn the turn the cable connector in a counter-clockwise direction to disassemble the unit.
2)
Please insert the cable in the correct groove in connector and turn the cable in a clockwise direction to combine the unit.
1)
Separate
the
connectors
that
are
connected
67
www.jdsol.co.kr
Version 1.4
JDS-S4R
3) Remove the brackets and wires completely and separate controller and
console. Replace new controller and assemble in reverse order.
68
www.jdsol.co.kr
Version 1.4
JDS-S4R
WARRANTY
Product :
Item :
JDS S4R
MFD :
Model :
JDS S4R
Warranty Expiration :
Manufacturer/Country of origin :
Identification code :
Purchase date :
Customer name :
Tel.:
Address :
Distributor Name :
Tel :
Address :
69
www.jdsol.co.kr