Академический Документы
Профессиональный Документы
Культура Документы
5. While using 3d wireframe as profile when creating a shaft, the profile must be?
A. Open and planar
B. Closed and planar
C. Projected.
6. Is it possible to create a pad with its top limit not being planar?
A. No, a pad is always flat at the top.
B. No, a pad is always infinite
C. Yes, by using up to surface option
D. Yes, by using up to plane option.
7. What type of object can you select as the neutral element when creating a draft angle?
A. Only a planar face
B. A planar face, non planar face, a plane, a surface
C. Only a plane
D. A planar face, a plane , a surface , a line
8. What is the difference between tangency and minimal propagation when creating a chamfer?
A. There is no difference
B. The tangency option is only available with surfaces
C. The tangency propagation propagates the fillet on an edge continuous in tangency and minimal
propagation will stop the fillet propagation at the first tangent continuity.
D. The tangency propagation propagates the chamfer on an edge continuous in tangency and minimal
propagation will stop the chamfer propagation at the first tangent continuity.
9. In the sketcher workbench how can you modify the grid spacing?
A. By using the tools + option menu
B. By using the mouse
C. It is not possible
D. None of the above
10. How can you get a tangent arc when creating a profile?
A. By using the esc key
B. By keeping the mb1 pressed and dragging the mouse
C. It is not possible
11. How can you create points that can be seen in sketcher but not in 3d workbench?
A. By creating points in another sketch
B. By using the `no show mode to hide the points
C. By converting the points to construction geometry using `sketch tools
12. How to you copy the length (or radius)of a line (0r circle/arc) to create a new one?
A. I drag the existing line on to the first point of the line to create
B. I place the cursor on the existing line and select parameters. Copy length or radius in the contextual
menu.
C. It can not be done.
13. When should i use spline on a sketch?
A. When i can not do it in wireframe and surfaces.
B. When i need a simple planar spline with few tangent and curvature controls.
14. How is a parabola created?
A. By entering its equation
B. By defining the focus and two end points.
15. When do i need to create an axis in the sketcher?
A. When i want to create a shaft or groove
B. To create the half of the part.
16. Why should we use predefined profiles instead of using simple profiles?
A. Because it is quicker
B. Because it is easier to modify
C. Because only predefined profiles can be used to create 3d parts.
17. How to close an arc?
A. Modify the arc end points in order to make them coincident
B. Use the close tool from the relimitations tool bar
C. Erase the arc and build the new circle.
18. How many objects would you get when you create the translation with the number of instances
equal to 2?
A. One translated object
B. Two objects
C. Three objects
D. Four objects
19. How to build two offset profiles on either side of the reference profile?
A. By using both side offset tool
B. By making two offset profiles
C. It is not possible
20. When a 3d edge has been projected on to the sketch plane, it is possible to remove the link
between the part and the projected element.?
A. Yes, using isolate
B. No, it is not possible
21. In the 3d space the elements created in the sketcher are taken as single entity?
A. True
B. False
22. To sketch on the face of an existing feature which of the following statement is not true?
A. The face the feature must be planar
B. The sketch is linked to the feature on which it is created
C. The existing feature should not contain any dress up features.
23. A new sketch will register in the specification tree when you enter sketcher workbench.
A. True
B. False
24.when you create a geometry in sketcher workbench points are implicitly created?
A. Yes
B. No
25. When you creating equidistance point in a line using parameters 10mm spacing and 50mm length
how many new points will be created?
A. 6 b. 4 c. 5 d.3
26. If i use `standard lines trim mode to create a corner for the selected elements shown below. What
will be the result?
a.
b.
C.
d.
27. An element can be toggled between a construction element and a normal element at any time
by selecting it, and deactivating the construction/standard element icon.
A. Yes
B. No
34.
A.
b.
C.
35. Choose the correct order specification tree for the following part
a. Pad
Draft
Fillet
Shell
b. Pad
Shell
Draft
Fillet
c. Pad
Fillet
Draft
Shell
d. Pad
Fillet
Shell
Draft
36. Choose the correct order specification tree for the following part
a. Pad
Shell
Draft
Chamfer
b. Pad
Pocket
Shell
Chamfer
c. Pad
Draft
Chamfer
Shell
d. Pad
Draft
Shell
Chamfer
37. Choose the correct order specification tree for the following part
a. Pad
Draft
Chamfer
Shell
b. Pad
Chamfer
Shell
Draft
c. Pad
Chamfer
Draft
Shell
d. Pad
Draft
Shell
Chamfer
38. Choose the correct order specification tree for the following part
a. Pad
Shell
Hole
Draft
b. Pad
Draft
Hole
Shell
c. Pad
Shell
Draft
Hole
d. Pad
Hole
Shell
Draft
39. Choose the correct order specification tree for the following part
a. Pad
Hole
Draft
Edgefillet
Shell
b. Pad
Draft
Hole
Edgefillet
Shell
c. Pad
Draft
Hole
Shell
Edgefillet
d. Pad
Edgefillet
Shell
Draft
Hole
40. Choose the correct order specification tree for the following part
a. Pad
Shell
Edgefillet
Draft
b. Pad
Edgefillet
Shell
Draft
c. Pad
Draft
Shell
Edgefillet
d. Pad
Draft
Edgefillet
Shell
41. Choose the correct order specification tree for the following part
a.
b.
c.
d.
42. Choose the correct answer for the below specification tree shown FOR PART1
A.
B.
C.
D.
43. Choose the correct answer for the below specification tree shown
A.
B.
C.
D.
44. Choose the correct answer for the below specification tree shown
A.
B.
C.
D.
45. Choose the correct order specification tree for the following part
A.
B.
C.
D.