Вы находитесь на странице: 1из 4

Data Sheet

Optimux-108L
Basic-Managed Four-Channel Fiber E1 Multiplexer

TDM over Fiber Four E1 channels multiplexed over a fiber optic link
Local and remote loopbacks
Various fiber interfaces: multimode, single-mode (up to 120 km), and
single-mode over single fiber
Transparent clocking

Optimux-108L multiplexer combines four Each of the four signals of the tributary
E1 channels over a fiber optic uplink. interface is transmitted independently
A pair of Optimux-108L units provides a ensuring that each channel can be set to a
simple and low-cost solution for different clock source.
connectivity over distances of up to
120 km.

The Access Company


Optimux-108L
Basic-Managed Four-Channel Fiber E1 Multiplexer

UPLINK INTERFACE TRIBUTARY INTERFACES POWER


Optimux-108L supports a variety of Optimux-108L has four balanced or Optimux-108L may be ordered with two
built-in optical uplink interfaces including: unbalanced E1 tributary channels different power supplies:
850 nm VCSEL (Vertical Cavity Surface transparent to customer clocking and A wide-range AC/DC power supply that
Emitting Laser) for multimode fiber data. can be connected to either an AC
1310 nm LED for multimode fiber power source or DC power source
DIAGNOSTICS
1310/1550 nm laser diode or long haul -48 VDC power supply.
Optimux-108L features comprehensive
laser diode for extended range over test and diagnostics capabilities that
single-mode fiber PHYSICAL
include local and remote loopbacks on
Single fiber (SF1, SF2 options) using a each E1 tributary link and uplink sent by Optimux-108L is a compact standalone
1310 nm and 1550 nm laser diode the corresponding OP-108C card in an unit. The optional rack mount adapter kits
transmitter with WDM technology, LRS-102 chassis. In addition, a local or enable installation of one or two
which enables the laser to transmit the remote loopback can be generated using (side-by-side) units in a 19-inch rack.
signal at a different wavelength than the DIP switch of the local or remote
the receive signal Optimux-108L unit.
Single fiber (SF3 option) using SC/APC Note: Local loopback on the uplink cannot be
(Angle-Polished Connector) generated via the LRS-102/OP-108C card.
technology, with a 1310 nm laser To facilitate system diagnostics,
diode for single wavelength operation. Optimux-108L feature LED status
indicators, LOS alarm recognition on the
optical link and on E1 channels 1 to 4.

Figure 1. Transparent Services and Clocks over Fiber

Figure 2. Range Extension of E1 over Fiber


Data Sheet

GENERAL
Specifications Power
Standards Wide-Range: 100 to -240 VAC and
TRIBUTARY INTERFACES -40 to 72 VDC
G.703, G.823 (E1), G.955, G.742
48 VDC: (40 to 57 VDC)
Number of E1 Channels
Diagnostics
4 Power Consumption
Local and remote loopbacks on each E1
tributary link and uplink Wide-Range: 11 VA, 2.7W
Data Rate
-48 VDC: 2W
2.048 Mbps Note: Local loopback on the uplink cannot be
generated via the LRS-102/OP-108C card. Physical
Line Code
Height: 4.37 cm (1.7 in)
HDB3 Timing
Uplink: internal Width: 21.7 cm (8.5 in)
Impedance Depth: 17.0 cm (6.7 in)
E1 tributary: transferred transparently,
120, balanced Weight: 0.5 kg (1.1 lb)
independent for each channel
75, unbalanced
Indicators Environment
Connector Temperature: 055C
PWR
Balanced: RJ-45 Humidity: Up to 95%, non-condensing
On (green): power supply OK
Unbalanced: two BNC connectors
Off: power supply is off or faulty

FIBER OPTIC INTERFACE LOSS/AIS LINK


On (red): Sync/Signal Loss on uplink
See Table 1.
On (yellow): AIS detected
Flashing (yellow) Loop is performed
on uplink
Off: normal operation
LOSS/AIS CH1 to CH4
On (red): Signal Loss on channel
On (yellow): AIS received on channel
Flashing (Yellow) Loop is performed
on channel
Off: normal operation
LINK SD
On (green): Optical signal is detected
Off: No optical signal is detected

Table 1. Standalone Fiber Optic Interface Characteristics

Wavelength Fiber Type Transmitter Type Typical Power Receiver Typical Max. Range Connector Type
Output Sensitivity
[nm] [m] [dBm] [dBm] [km] [miles]
850 62.5/125 multimode Laser (VCSEL) -7 -34 6 3.7 ST, SC, FC/PC
1310 9/125 single mode Laser -12 -34 47 29.2 ST, SC, FC/PC
1310 62.5/125 multimode LED -18 -32 7 4.3 ST, SC
1550 9/125 single mode Laser -12 -34 47 29.2 ST, SC, FC/PC
1310 9/125 single mode Laser (long haul) -2 -34 72 44.7 ST, SC, FC/PC
1550 9/125 single mode Laser (long haul) -2 -34 120 74.5 ST, SC, FC/PC
Tx: 1310 Rx: 1550 9/125 single mode Laser WDM (SF1) -12 -34 47 29.2 SC
Tx: 1550 Rx: 1310 9/125 single mode Laser WDM (SF2) -12 -34 47 29.2 SC
Tx/Rx: 1310 9/125 single mode Laser (SF3) -12 -27 20 12.4 SC/APC
Note: Typical ranges are calculated according to attenuation of 3.5 dB/km for 850 nm multimode fiber, 0.4 dB/km for 1310 nm single mode fiber, and 0.25 dB/km for
1550 nm single mode fiber.
Data Sheet
Optimux-108L
Basic-Managed Four-Channel Fiber E1 Multiplexer

product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders.
324-110-09/09 Specifications are subject to change without prior notice. 19972009 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven, and the
SUPPLIED ACCESSORIES
Ordering + Fiber optic link interface: AC power cord and AC-DC adapter plug
OP-108L/~/^/#/+ 85L 850 nm, multimode, VCSEL
Legend 13 1310 nm, multimode, LED OPTIONAL ACCESSORIES
Note: Available with ST and SC
~ Power supply (Default=AC/DC
connectors only RM-33-2
wide-range power supply):
13L 1310 nm, single mode, laser Hardware kit for mounting one or two
-48 VDC 40 to 57 VDC
diode plastic units in a 19-inch rack
^ E1 connector: 15L 1550 nm, single mode, laser
B Balanced (RJ-45) diode
U Unbalanced (BNC) 13LH 1310 nm, single mode,
long-haul laser diode
# Uplink interface connector: 15LH 1550 nm, single mode,
ST ST type connector long-haul laser diode
FC FC/PC type connector SF1 Transmit 1310 nm laser
SC SC type connector (WDM), receive 1550 nm
Note: ST and FC connectors are not available SF2 Transmit 1550 nm laser
for the single fiber options. (WDM), receive 1310 nm
SF3 Transmit and receive at
1310 m laser diode
Note: For single fiber applications, a device
with SF1 interface is always used opposite a
device with SF2 interface, and vice versa. An
SF3 interface works only opposite another
SF3 interface.

International Headquarters North America Headquarters


24 Raoul Wallenberg Street 900 Corporate Drive
Tel Aviv 69719, Israel Mahwah, NJ 07430, USA
Tel. 972-3-6458181 Tel. 201-5291100
Fax 972-3-6498250, 6474436 Toll free 1-800-4447234
E-mail market@rad.com Fax 201-5295777
E-mail market@rad.com

www.rad.com Order this publication by Catalog No. 803860


The Access Company

Вам также может понравиться