Академический Документы
Профессиональный Документы
Культура Документы
front page Forum Instructions Search Calendar Classifieds Advertise Facebook Donations Log in Sign up
CNC - Harrastus--> Forums -> CNC MACHINE DESIGN, CONSTRUCTION AND TESTING -> CNC projects and the rest of us -> CNC V3
Previous next
However, I ended up making the steel frame of the machine, the manufacturing industry is familiar and almost all the essential was at hand
myden materials.
The cutter body is shaped knee. The starting point for the design was to cut off all the useless and make the machine as simple as possible
and easy to prepare (when I'm lazy ).
1 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
Tystala is X350 Y200 Z250. The fourth shaft reservation at this stage. The machine I tried to take advantage of each other as much as
possible the same components.
The frame consists of RHS pipe, as well as laser / flame-. The base frame is made of two parallel 100x100x8 tube and welded together using
a clip lattaa +. The build is reasonably jmklt and torsion.
2 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
The column is of 180x100x10 tube which is supported behind jykkreill 15mm. This became somewhat simulated FEMill and I said that my
use of this post will not bend. Takajykkrit as close to the outer walls of the tube, however, so that the weld did not have to meet any
nonsense groove. The basis for guide rails 30x20 flat iron.
The column is attached to the lower frame by six M12 bolts 12.9.
3 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
The Z-axis of the jaw is welded and machined 8-15mm laser cut straight. The picture shows over the hole locations Farolla. Round hole will
3W LED spotlight to provide working lights. The other end of the housing has to go hand hole, which may be screwed mm. spindle mounting
bolts.
Housing components are annealed before machining emission approx. 650 degrees (Hilamet Ltd). Hull possible to fill eg. Epoxy afterwards if
needed (so far I do not think that it is).
Undercarriage is easy to machine, everything gets machined in one setting 3-axis center.
The column is more difficult, because the underside of the column should get a 90-degree angle to the guide surface. As of this writing the
column machining is finished, so more on that later how it is managed. Nearly all machining operations have been conducted on the
province's professional schools. Schools when utilized, will have to prepare for stretching and errors in your project, but let's not bring the
price policy of not much strain the wallet. The body parts painted in blue RAL 5002 powder paint.
4 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
Rowball second axis which is mounted against a machined reference edge, wherein the second guide track is clocked by the then parallel.
Snowmobile is responsible for refenssireunat plate portions.
The guide tracks Hiwin 20mm Ball monorail guidance systems flanged snowmobile. Flanged, therefore, that in these more contact surface of
the mounting part, as well as in my case, have to be part of the sleds to install the opposing party through bolts M5 (sleds M6 threaded holes
as standard). The fixing screws are used mainly in strength class 12.9 bolts where possible.
Modded ballscrew Chinese 16/5 kuulauruuvit (at least for now, to begin with). I changed in larger balls which I had reduced clearance
commendable. Similarly, the Chinese bearing housings changed THK's Jap would bungle. The screw pitch error remains to be seen.
5 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
The table top is machined from a single sheet blank 40mm (650x200, machined weight 32kg). The top surface of the plate will be the poor
man's T-grooves, a bolt-T-shaped hardened flats. Now, when you started the Christmas holidays, so there is little time to reconcile the
elements. I make the final placement on the lower frame within a week or two when the parts are transported workshop and the machine can
pile up on top of the finished base.
6 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
XY axes placement will be a little tricky, but you should be able in a certain order.
Different karavaihtoehtoja became a lurking sense, probably half a year. From the spindle is always ebay halpiskaroista self-made equipped
with a tool changer. Again I returned again in the end the design starting point, that is, minimizing the tasks themselves parts. This shut off
the self-made stem, which would have been quite a lot of trouble. I ended up finally to conduct a spindle in a Chinese factory, which produces
many of the "European" suurnopeuskarat. I got to choose the area of power, revolutions, the bearings, the operating voltage, etc. In the end
I ended up with an air-230V 200Hz spindle with ER25 holkkikiinnitys, 1,5kW power and maximum revolutions are 12000rpm. The lower end of
a bearing ceramic angular contact ball bearings 7007 2p and 2p rear end of 7004 deep groove ball bearings. Karan quality I am very satisfied.
The weight of more than 11kg.
7 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
This is now the top priority information rather narrow voiceovers. Electric coin is completely ready and functional, tested. More on that in the
next mail to publish your Picasa gallery with a link to it as long as I get a little cleaned, there are pictures fairer admissible.
Mikko
http://picasaweb.google.com/mikkokuivamaki/
8 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
why this should be a really good sign of any material. Continue the good work, good will come.
Posts: 709
Registered: 11/01/2006 Registered
http://www.diy600.net
Liikkeenohjauskortiksi selector EdingCNC's CPU5A4 USB card. The card also includes CNC control software, which mm. built-in simple CAM.
Experience so far are good, the deployment was easy and fast. You can read more detailed specs of the card here:
http://www.edingcnc.com/index.php?pagina=detail_producten&productenid=56
The spindle is controlled by a frequency converter 2,2kW Delta. Tamu purchased Jonne, I can wholeheartedly recommend the technical
support and affordable prices due! The spindle is controlled in accordance with the g-code on / off and speed reference comes from analog
0-10V data.
9 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
I made a simple hand the baton with the program start / stop and emergency stop buttons.
10 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
Electrical components intervals on the cabinet. I had to because of the scarcity of space to put the power supply on the door.
Testing of electrical power. At first I had problems with the electrical contact to earth the inverter disrupted the USB connection. Right, so I
built ground connections again and the problems went away. CPU's Ethernet version would be more reliable precisely because of similar
problems.
11 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
As long as I get the column machining, can I build up a machine in earnest. Primary movements should no longer impossible time to go.
I updated the first post office that promised Picasa link. There are more photos, captions, however flyfishing
http://picasaweb.google.com/mikkokuivamaki/
Posts: 248
It is indeed becoming a handsome contraption!
Registered: 20/08/2011
Stung on earth and indeed more pictures noi says a lot ... Nice to read valmistustas with a description and a photo from
Registered
Registered
Posts: 207 One comment yes I did, the same that is in many ways as a commercial device, ie the main switch is not advisable to wire the door but the body of the
Registered: 26/09/2006 housing and on the way to the door. The danger is frequently the door is opened, wire insulation may vauorioitua
Yeah, that is how it is. This became used existing parts so let's go with these. The target, of course, is that the cabinet does not just break
tarvisi. To be certain, I did a double protection "mobile" wirings. That is, the network sock and kierrespiraalia on, should just as soon wear
through the cable ties and johtoankkureitakaan has not been spared.
Registered
http://picasaweb.google.com/mikkokuivamaki/
Posts: 724
Those closed loop stepper motors and drivers began to interest, kuikas they work in practice an overload situation, whether the notification of
Registered: 04/01/2011
the controller pc games notta stop, if the axis does not reach as far as the driver commands. Or whether PC controller directly to the actual
position data of the engines
12 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
Registered
http://www.leadshine.com/UploadFile/Down/HBS86d.pdf
http://www.leadshine.com/UploadFile/Down/HBSsm.pdf
Registered
http://picasaweb.google.com/mikkokuivamaki/
http://picasaweb.google.com/mikkokuivamaki/
There is, therefore, the Chinese RM1605 ball screws, which promises accuracy class C7 that is 0.05mm / 300mm. Well, when talking about
the Chinese tolerances, then the error is of course much higher in reality. Tuning up the side of the optical axes of the measuring rod, with a
resolution of 0.01mm. Error relatively linear rise and the Y-axis 225mm with regard to the way the whole business was 0.21mm short.
EdingCNC However, the softassa is possible to correct the pitch error in software. With a simple code snippet program can read the table,
which compensates for the increase in the error nolliin. For example
0.000 0.000
100.000 100.050
200.000 200.080
The left-hand value is posted to, and the right describes how much the engine must be actually runs the commanded value is reached.
The values can be entered how densely wants, rather than an error, needs to be linear. After the compensation already looks much better:
13 of 14 14/02/2017 21:41
CNC V3 http://www.cnc-tekniikka.com/CNC-forum1/index.php?topic=6400.0
http://picasaweb.google.com/mikkokuivamaki/
Registered
Timi
Registered
http://picasaweb.google.com/mikkokuivamaki/
Registered
Posts: 201
Registered
Registered: 10/07/2011
Timi
www.metalguru.fi
Previous next
CNC - Harrastus--> Forums -> CNC MACHINE DESIGN, CONSTRUCTION AND TESTING -> CNC projects and the rest of us -> CNC V3
Powered by EzPortal
Facebook Comments
14 of 14 14/02/2017 21:41