Вы находитесь на странице: 1из 22

L14 Speed Integration with Ethernet-enabled

CENTERLINE MCCs, Rockwell Software Studio


5000 and IntelliCENTER Software
Configuration Guide
L14 Speed Integration with Ethernet-enabled
CENTERLINE MCCs, Rockwell Software Studio
5000 and IntelliCENTER Software

Contents
Lab Setup and Configuration Information .................................................... Error! Bookmark not defined.
Lab Information ............................................................................................. Error! Bookmark not defined.
Hardware Configuration ................................................................................ Error! Bookmark not defined.
Computer/Host Settings ................................................................................ Error! Bookmark not defined.
Application/Programming .............................................................................. Error! Bookmark not defined.
Additional Equipment Required .................................................................... Error! Bookmark not defined.
RSLinx Driver Configuration ...................................................................... Error! Bookmark not defined.
Application Versions ...................................................................................... Error! Bookmark not defined.
Introduction to Your Lab Hardware ............................................................... Error! Bookmark not defined.
Pre-Lab Checks ............................................................................................ Error! Bookmark not defined.

3 of 22
Lab Setup and Configuration Information

Lab Information

Speed Integration with Ethernet-enabled CENTERLINE MCCs,


Lab Name Rockwell Software Studio 5000 and IntelliCENTER Software
Experience the ease of integrating CENTERLINE Motor Control Centers
(MCCS) with EtherNet/IP and their associated components --
PowerFlex drives and E300 overload relays. Streamline your workflow
by leveraging the simplified integration of IntelliCENTER software and
Studio 5000 Logix Designer to simplify device configuration and reduce
Lab Description commissioning time and errors.
Lab Creator Justin Lemminger
Date Created 08/27/2015
Updates:

Hardware Configuration
Qty Demo Cat.# / Description Communication Location Firmware
CLX41 / ControlLogix 4-slot
1 Demo Box
1756-L75 / ControlLogix
controller Slot 1 v27.011
1756-EN2TR / Ethernet
communication module 192.168.1.11 Slot 2 v5.008
Stratix 5700 6-port switch 192.168.1.120 Lite
1 11P012A / IMC Demo Box
PowerFlex 755 drive 192.168.1.30 v11.02
20-HIM-A6 / Human
Interface Module Slot 1 v2.005
20-750-2262C-2R / 24
VDC I/O Module Slot 7
E300 / Overload 192.168.1.21 V5.082
ETAP 192.168.1.150
10P007A / External IMC
1 Motor Box

4 of 22
Computer/Host Settings
Location Files
Computer Name WIN7-VM
IP Address 192.168.1.1
Operating System Windows 7 Enterprise SP1 64-bit

5 of 22
Photograph of Hardware:

ControlLogix Demo Box

The 1756-EN2TR is the EtherNet/IP card used for connecting the controller to the Stratix 5700.

IMC Demo Box

6 of 22
IMC Motor Demo Box

Digital Input Assignments (I/O card in Slot 7 of the PowerFlex 755 drive)
o Di 0 = Stop (Right Position)
o Di 1 = Start (Left Position)
o Di 2 = Forward / Reverse (Left Position)
o Di 3 = Clear Faults (Left Position)
o Di 4 = Jog 1 (Left Position)
o Di 5 = Enable (Right Position)

7 of 22
Basic Setup Diagram

Network Diagram
Ethernet Connections

Stratix 5700 Port End Device

1 PC
2 EN2TR Port 1 (Left)
3 E300 Overload Relay
4 PowerFlex 755

8 of 22
Application/Programming
Location Files
C:\Lab Files\L14 - Speed Integration with
Ethernet-enabled CENTERLINE MCCs,
Rockwell Software Studio 5000, and
IntelliCENTER Software EtherNet_MCC.ACD
C:\Lab Files\L14 - Speed Integration with
Ethernet-enabled CENTERLINE MCCs,
Rockwell Software Studio 5000, and
IntelliCENTER Software\Configuration Files IMCE11B_012A_IntellicenterLab_DeviceCfgs.ACD

Additional Equipment Required


Qty Items
2 1585J-M8TBJM-2 : 2m Ethernet Patch cord

RSLinx - Driver Configuration


Topic Name Path to Hardware
AB_ETHIP-1 192.168.1.11 (EN2TR)
192.168.1.21 (E300)
192.168.1.30 (PF755)
192.168.1.120 (Stratix 5700)
192.168.1.150 (ETAP)

Application Versions
Service
Version
Vendor Software Pack
RA RSLinx Classic Gateway 3.74.00 CPR9 SR 7.4
RA Studio 5000 27.00.00 CPR9 SR 7.4
RA IntelliCENTER 6 (Beta)
RA FactoryTalk EnergyMetrix 2.20.00 (Build 55)
RA Connected Components Workbench 8.01.00

9 of 22
Required Pre-Lab Configuration

This section is meant to help setup the lab to the proper configuration. If you are the lab attendee, please ignore this Pre-Lab
Checks section and go the Using IntelliCENTER Integration Assistant section.

IMC Demo Box Device Configuration

PowerFlex 755

1. Verify the I/O option module has been added to Slot 7. Options modules should be added prior to
energizing the demo.

2. Energize the drive demo: back view of IMC Demo box. Put the switch by the plug in the | position
and put the breaker switch in the up position.

Make sure the E-Stop is pulled out (toward you)

10 of 22
3. Verify that the PowerFlex 755 drives IP Address Switches are set to 030.

If the address is not 030, set this by adjusting the rotary switches. After adjusting the switches, cycle
power to drive demo.

4. If the PowerFlex 755 is faulted, then reset the fault by clicking the red stop button on the HIM.

11 of 22
Drive Configuration (REQUIRED!!!!!)
This drive configuration process is required due to L05 PowerFlex Drive lab and L14 IntelliCENTER
lab using the same PowerFlex 755 drive with different configurations respectively. These particular steps
are required before every L14 Speed Integration(IntelliCENTER) lab session.
1. Put processor into Program Mode (right key position) then Remote Mode (middle key position)
2. Open the IMCE11B_012A_IntelliCENTERLab_DeviceCfgs.ACD file located in the C:\Lab
Files\L14 - Speed Integration with Ethernet-enabled CENTERLINE MCCs, Rockwell Software
Studio 5000 and IntelliCENTER Software\Configuration Files folder.
3. Open the PF755_Drive module within the I/O tree.
4. Go to the Drive Tab and click the Download button / icon to download the drives configuration for this
lab.
5. When the I/O Configuration difference screen appears, click Use Project and click Continue
6. Click Download to send down the drive configuration.
7. Once the drive configuration has been downloaded to the drive, then click Ok.
8. Download the project file to the controller. Keep the controller in Program Mode.

12 of 22
Disable DeviceLogix Program

If a DeviceLogix Program is loaded and running in the PowerFlex 755 demo, the DeviceLogix logic needs
to be disabled and the drive reset prior to conducting the lab.
1. Use Drive Executive or Connected Components Workbench to connect to the drive. These steps can also be completed
using the HIM.
2. Navigate to the Status & Control parameters under the DeviceLogix port

3. Set parameter #53 DLX Operation to DisableLogic

13 of 22
4. Next, highlight 0 PowerFlex 755, right-click and select Reset Drive

(For the HIMselect Port 0, select DIAGNOSTIC folder then Reset Device.)

5. Finally, click OK to reset the drive. Communications will be lost at this time.

(For the HIMwhen prompted to confirm reset device, click ENTER.)

14 of 22
E300 Overload
In order to modify parameters in the E300, you will need to access the web interface. Follow the steps below to enable and
access the web interface for the E300.

1. Verify that the E300 PHASE LOSS switch is in the left position and the E300 Hand-Off-Auto is
turned to OFF.

2. Set the EXT. MOTOR switch to E300 for the lab.

3. If the E300 is faulted, then reset the fault by clicking the TEST/RESET button on the E300.
4. Locate the E300 Overload and slide down the front cover on the device to access the three rotary
switches that are used to set the last octet of the IP Address.

15 of 22
5. Verify that the rotary switches are set to 0 - 2 - 1 to represent the IP Address 192.168.1.21.
6. Cycle power on the device by removing the 120 VAC connector located behind the EtherNet/IP ports.
7. Open Internet Explorer.
8. Type the IP Address of the E300 (192.168.1.21) in the browsers URL window and press Enter.

9. Slide down the front cover on the device to access the three rotary switches that are used to set the
last octet of the IP Address.

10. To enter Administrative Mode, use a small flat blade screwdriver to turn all three of the rotary
switches to 0 - 0 - 0.
11. Cycle power on the device by removing the 120 VAC connector located behind the EtherNet/IP ports.
12. Type the IP Address of the E300 (192.168.1.21) in the browsers URL window and press ENTER to
access the web server. The device is now in Administrative Mode.

16 of 22
10. Select Administrative Setting from the menu on the left side of the screen.

13. Select Network Configuration from the expanded menu

17 of 22
14. You will be prompted to enter a User Name and Password in order to view these settings. Type
Administrator for the User Name and enter the serial number of the E300 communication module
into the Password field. Then select OK.

15. After you have access to the Network Configuration menu, locate the Web Server Control dropdown
menu and select Always Enabled. This will permanently enable the web server and disable the
rotary switches on the E300.

Locate the Network Interface information and type the IP Address (192.168.1.21) and Subnet Mask
(255.255.255.0) into the appropriate boxes.

If needed, download the IMCE11B_012A_IntellicenterLab_DeviceCfgs.ACD to the 1756-L75 controller to ensure


proper E300 Overload operation. You can also use this file to downlaod the proper drive configuration as well.
Utilize the Drive Tab within the Add-On Profile.
This file is located at C:\Lab Files\L14 - Speed Integration with Ethernet-enabled CENTERLINE MCCs, Rockwell
Software Studio 5000 and IntelliCENTER Software folder

18 of 22
CLX Demo box

1. Set the switch labeled 120/220V to on. Top of plug.

2. Ensure the L75 ControlLogix controller is in Slot 1 of the Logix chassis.

3. Verify the IP address on the EN2TR module to be 192.168.1.11. You will see it scrolling across the
display

4. If the address was not set to 192.168.1.11, remove the module from the Logix chassis and set the
rotary switches to 011 and put the module back in Slot 6 of the Logix chassis.
5. Use RSLinx to verify that the Stratix 5700 switch has the IP address set to 192.168.1.120. Right click
on Stratix 5700 and open Module Configuration.

19 of 22
6. Go to Port Configuration and verify the IP address is 192.168.1.120. If not change it and hit Apply.
The password for the switch will be needed to allow the IP address to change. The password is
rockwell. For note, the user name is left blank if accessing the switch through Internet explorer.

20 of 22
Additional Information

21 of 22
22 of 22
Publication: CE-DM225 December 2015 Copyright 2015 Rockwell Automation, Inc. All rights reserved.

Вам также может понравиться