Академический Документы
Профессиональный Документы
Культура Документы
WASHING MACHINE
Contents
EN
Installation, 2-3
EN Unpacking and levelling
Connecting the cold water and electricity supplies
English,1 Technical data
Troubleshooting, 11
Assistance, 12
1
Installation
Keep this instruction manual in a safe place for If positioned on a fitted carpet or a rug, adjust the
GB future reference. If the appliance is sold, given away feet in such a way as to allow room for air to circulate
or moved, please ensure the manual remains with the and provide ventilation beneath the washing machine.
machine so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully it
Connecting the cold water and
contains important information regarding the safe
electricity supplies
installation, use and maintenance of the appliance.
Connecting the water inlet hose
You will find the guarantee and other details relating to
Before connecting the inlet hose to the cold water supply,
the installation process in the bag containing this booklet.
allow the water to flow from the tap until it runs clear.
Unpacking and levelling
1. Connect the inlet hose
Unpacking
to the machine, by
1. Once the washing machine has been removed screwing it into the cold
from the packaging, check that it has not been water inlet on the upper
damaged during transportation. right hand side of the
If it has been damaged, contact the retailer and do back of the machine (see
not proceed any further with the installation process. figure).
Packaging materials should not be used as toys by children. The water pressure at the tap must fall within the values
indicated in the Technical data table (see next page).
Levelling
If the water inlet hose is not long enough, contact a
1. Position the washing machine on a level and sturdy
specialist store or an authorised technician.
floor, without resting it against walls or cabinets.
2. If the floor is uneven,
Always use the new water inlet hoses supplied with
the feet of the appliance
the machine.
may be adjusted until it
reaches a perfectly
horizontal position (the
angle of inclination must
not exceed 2 degrees).
2
Drainage Connection The cable should be replaced only by authorised
technicians. EN
Connect the outlet hose
to a draining duct or a Warning! The company shall not be held responsible
stand pipe at a height for any incidents that occur if these regulations are
between 65 and 100 cm not observed.
from the floor. Do not
65 - 100 cm bend it under any
circumstances.
3
Description of the machine
EN CONTROL
PANEL
DOOR
DOOR
HANDLE
KICK STRIP
ADJUSTABLE FEET
1. pre-wash
compartment: use
powder detergent.
1 2. main wash
2 compartment: use
powder or liquid
detergent. If you intend to
use liquid detergent, we
recommend that it is
poured into the
compartment immediately before the wash cycle is
started.
compartment for additives: for fabric softener or
other liquid washing additives. Do not exceed the
maximum level indicated by the grille, and dilute
concentrated fabric softeners.
Detergents and additives must be specific to front-
loading machines.
4
Control panel
EN
OPTION WASH
buttons and START/PAUSE
PROGRAMME indicator lights CYCLE
button with indicator light
knob PHASE
icons
ON-OFF/CANCEL button with indicator light : WASH CYCLE PHASE icons: these light up to
press the button briefly to switch the machine on or provide an indication of the progress of the wash
off. The green indicator light shows that the machine cycle (Wash - Rinse - Spin - Final draining
is switched on. To switch the washing machine off phase ).
during a wash cycle, press and hold the button for The text lights up when the cycle has finished.
approximately 2 seconds; pressing the button quickly
START/PAUSE button with indicator light: when the
or accidentally will not switch the machine off.
green indicator light flashes slowly, press the button to
If the machine is switched off during a wash cycle,
start the wash cycle. When the cycle has started, the
the programme will be cancelled.
indicator light is illuminated in a fixed manner. To
PROGRAMME knob: this can be rotated in both pause the wash cycle, press the button again; the
directions. To set a more suitable programme, please indicator light will turn orange and begin to flash
refer to the Table of Programmes. again. If the Door Locked indicator light is off,
The knob is locked into position during the wash cycle. the porthole door may be opened.
To restart the wash cycle from the point at which it
TEMPERATURE button: press this button to was interrupted, press the button again.
adjust the temperature; the value will be identified by
the display above (see Running a wash cycle). DOOR LOCK indicator light: this indicates that
the porthole door is locked. To open the door, pause
SPIN SPEED button: press this button to adjust the wash cycle (see following page).
the spin value or to exclude this part of the In some programs, for safety reason, it is not
programme; the value will be identified by the display possible to open the door once the cycle has started.
above (see Running a wash cycle).
CHILD LOCK button and indicator light: this is
DELAY TIMER button: press to set a delayed start
used to enable or disable the Child lock function, by
time for the selected programme; the delay time will
pressing the button for approximately 2 seconds.
be identified by the display above (see Running a wash
When the indicator light is illuminated, the control
cycle).
panel is locked. This avoids accidental changes being
OPTION buttons and indicator lights: may be used to made to the wash cycles, especially where children
select any of the available options. The indicator light are at home.
corresponding to the selected option will remain lit
ECO indicator light: the icon lights up when the
(see Running a wash cycle).
electricity saving reaches at least 10% (this can be
achieved by adjusting the wash cycle settings).
5
Running a wash cycle
4. CLOSE THE PORTHOLE DOOR. 7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light
5. CHOOSE THE PROGRAMME. Turn the
remains lit in a fixed manner and the porthole door
PROGRAMME knob left or right to select the
locks (the DOOR LOCK indicator light illuminates).
required programme, to which a set temperature
The icons corresponding to the different wash
and spin speed are linked (these values may all be
phases will light up during the cycle, indicating the
modified).
progress. To change a programme while a cycle is
6. CUSTOMIZE YOUR WASHING CYCLE. To in progress, pause the washing machine by
customize a selected programme, use the relevant pressing the START/PAUSE button; then select the
buttons on the control panel represented by the desired cycle and press the START/PAUSE button
following icons: again.
To open the door while a cycle is in progress press
Modify the temperature and/or the spin the START/PAUSE button; if the DOOR LOCK
speed. The machine automatically selects the indicator light switches off it is possible to open the
temperature and the maximum spin speed for the door. Press the START/PAUSE button again to
programme set and these values may not be restart the programme from the point at which it
increased. By pressing the button, the tempera- was interrupted.
ture can be progressively reduced or even set to
cold wash ( ). By pressing the button, the spin 8. PROGRAMME END. The icon "END" in the wash
speed can be progressively reduced or even cycle phase lights up to indicate that the
eliminated altogether ( ). If the buttons are programme has ended. The porthole door may be
pressed again the maximum values are restored. opened immediately. If the START/PAUSE button
flashes, press the button to end the cycle. open
Exception: if the WHITES programme is selected, the door, unload the laundry and switch off the
the temperature can be increased up to a value of machine.
90C.
If you wish to cancel a cycle that has already
Setting a delayed start. begun, press and hold the button. The cycle will be
To set a delayed start for the selected programme, stopped and the machine will switch off.
press the button repeatedly until the desired delay
time is displayed (this may be between 1 hour and BAG FOR QUILTS, CURTAINS AND DELICATE
24 hours). GARMENTS
To disable the function press the button until the
text is displayed. Ariston has made it easier for you to wash even the
N.B.: Once the button START/PAUSE has been most valuable and delicate garments in complete
pressed, the delay time may only be decreased. confidence thanks to the special bag which protects
the laundry (this is supplied with the machine).
We recommend that the bag is used every time you
wash quilts and padded items with an outer layer
made using synthetic material.
6
Programmes and options
Table of Programmes
EN
Max. Maximum load
Max. Detergent
spin (kg) Cycle
Icon Programme description tempera-
speed Fabric Using duration
ture (C) Washing Normal Mini
(r.p.m.) softener load
Everyday programmes
60
WHITES 1200 l l 8 3. 5
(Max 90)
COLOUREDS 40 1200 l l 8 3. 5
Wash options
Extra Rinse
Super Wash This programme increases the efficiency of the rinse
This option should be used for normal soiled cotton phase and ensures that a greater amount of
loads, in conjunction with other Everyday detergent is removed. It is particularly recommended
Programmes to ensure optimum washing results. for skin types that are sensitive to detergents. We
recommend this programme is used when the
It is not compatible with the Fast Wash, Silk, washing machine is full or when a large amount of
Wool, Duvets and Partial programmes. detergent has been used.
This option is not compatible with the Fast Wash,
Reduced creases Durable Spin, Delicate Spin and Draining
If this option is selected, the wash and spin phases programmes.
will be adjusted accordingly so that fabric creasing is
reduced. At the end of the cycle the drum of the Mini load
washing machine will spin slowly; the Reduced This function should be used when the amount of
creases and START/PAUSE indicator lights will flash. laundry is half, or less than half, of the maximum
To end the cycle, press the START/PAUSE button or recommended load (see Table of Programmes).
the Reduced creases button.
When using the Silk programme, the machine will This option is not compatible with the Durable
end the cycle while the laundry is soaking and the Spin, Delicate Spin and Draining programmes.
Reduced creases indicator light will flash. To drain
the water so that the laundry can be removed, press
the START/PAUSE button or the Reduced creases
button.
This option is not compatible with the Wool, Durable
Spin, Delicate Spin and Draining programmes.
7
Detergents and laundry
8
Precautions and tips
This machine was designed and manufactured in Opening the door manually
compliance with current international safety EN
If it is not possible to open the porthole door due to a
standards. The following advice is provided for safety
powercut and you wish to hang out the laundry,
reasons and should be read carefully.
proceed as follows:
General safety
1. Remove the plug from
This appliance was designed for domestic use the electricity socket;
inside the home and is not intended for commercial 2. Make sure that the
or industrial use. water level inside the
The washing machine must be used by adults only, 20
machine is lower than the
in accordance with the instructions provided in this door opening; if this is not
booklet. the case remove excess
Do not touch the machine when barefoot or with water using the water
wet or damp hands or feet. outlet hose, collecting it in
When unplugging the appliance, always pull the a bucket as shown in the
plug from the mains socket; do not pull on the figure;
cable.
Do not touch the drained water as it may reach 3. Remove the kick strip
extremely high temperatures. on the front of the
Never force the porthole door: doing so may washing machine using a
damage the safety lock mechanism designed to screwdriver (see figure);
prevent the door being opened accidentally.
If the appliance breaks down, under no
circumatances must you attempt to carry out the
repairs yourself.
Keep children well away from the machine while it
is in operation.
If the machine must be moved, work in a group of
two or three people and handle it very carefully.
Never attempt to move the appliance without the 4. Using the tab shown in
help of another person, because it is very heavy. the figure, pull outwards
Make sure that the drum is empty before loading until the plastic brace
laundry into the appliance. comes away; pull it
downwards until you hear
Disposal a click, which indicates
that the door is unlocked;
When disposing of the packaging material: observe
local legislation so that the packaging may be reused.
Disposing of an old washing machine:
before scrapping your appliance, cut the power
supply cable and remove the appliance door. 5. Open the door; if this is
still not possible, repeat
the process;
9
Care and maintenance
2. Position a container
Cleaning the machine under the screw cap to
collect the drained water
The exterior of the appliance and all rubber parts may correctly (see figure). Expect approximately 1.5 litres if
be cleaned using a cloth soaked in warm soapy the cycle has finished
water. Do not use solvents or abrasive products. completely;
3. Unscrew the cover,
turning it in an
Cleaning the detergent dispenser anticlockwise direction
drawer (see figure);
10
Troubleshooting
From time to time your machine may not operate as it should. Before calling for Assistance (see Assistance), make sure that
the problem cannot be resolved easily using the following list. EN
Malfunction: Possible causes / Solutions:
The washing machine will not The plug has not been inserted into the electrical socket properly or there is no
switch on and no lights appear power in the house or electrical socket.
on the control panel. There is no power in the house.
The wash cycle The porthole door has not been shut properly.
does not begin. The START/PAUSE button has not been pressed.
The water tap has not been turned on.
The washing machines fails to fill The water inlet hose is not connected to the tap.
with water. The hose is kinked.
The water tap has not been turned on.
There is no water in the house.
The water pressure is insufficient.
The START/PAUSE button has not been pressed.
The machine continuously fills The end of the outlet hose has not been fitted at a height between 65 and 100
and drains water. cm from the floor (see Installation).
The free end of the hose is underwater (see Installation).
If If the dwelling is on one of the upper floors of a building, there may be
problems relating to water drainage, causing the washing machine to load and
drain water continuously. Special anti-draining valves are available in shops and
help to avoid this inconvenience.
The water drainage system is not fitted with a breather pipe.
The machine does not drain The programme does not include a draining phase: some programmes require
or spin. manual draining (see Programmes and options).
The Reduced creases option is enabled: to complete the programme, press the
START/PAUSE button (see Programmes and options).
The outlet hose is bent (see Installation).
The drainage duct is clogged.
The washing machine vibrates The drum was not unlocked properly when the appliance was installed
too much during the spin cycle. (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and a wall (see Installation).
The load is not balanced properly (see Description of the machine).
The washing machine leaks. The water inlet hose is not screwed on to the tap correctly (see Installation).
The detergent dispenser drawer is blocked (for instructions on how to clean it,
see Care and maintenance).
The outlet hose has not been secured properly (see Installation).
The icons corresponding to the Wash Switch off the machine and unplug the appliance; wait for approximately 1
Cycle Phase flash rapidly at the same minute then switch it on again.
time as the ON/OFF indicator light. If the problem persists, contact Assistance.
There is too much foam. The detergent is not designed for machine washing (the packaging should state that
the product is for washing by machine, for washing by hand or machine or similar).
Too much detergent was used.
The washing machine door Follow the manual unlocking procedure (see Precautions and tips).
remains locked.
Display above Spin Speed button Drain Pump may be blocked, see "Cleaning the Pump" under the "Care and
shows "F-05" and the machine Maintenance " chapter.
will not run any programme.
If the problem persists after the above checks have been carried out, shut off the
water tap, switch off the machine and contact Assistance.
11
Assistance 195055735.02
12/2006 - Xerox Business Services
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service.
Never use the services of an unauthorised technician.
12