Академический Документы
Профессиональный Документы
Культура Документы
DMSWITCH-EDD
INSTALLATION GUIDE
204-4117-04 rev. 05 Date: 22/11/2010
WARRANTY
This product is guaranteed to be free against manufacturing and raw material defects, during the period
specified in the sales receipt.
The warranty includes only the repair and replacement of components or defective parts, free of charge.
The warranty does not cover damages caused by any one of the following conditions: improper use,
energy failures, natural phenomena (lightning, for example), failure in equipments connected to this
product, improper grounding or repairs done by DATACOM unauthorized personnel.
This warranty does not cover repairs done at the customers site. All equipments must be sent to
DATACOM to be repaired.
Although this document has been written with care, the company does not assume responsibility for
occasional mistakes and omissions in its content. Likewise, DATACOM is not liable for any damages that
may result from the use of the information contained in this manual. Specifications provided in this
manual are subject to changes without any previous notice and should not be construed as a
commitment of any kind by DATACOM.
CONTACTS
In order to contact the DATACOM technical support, or sales department:
Support
o E-mail: suporte@datacom.ind.br
Sales
o E-mail: comercial@datacom.ind.br
Internet
o www.datacom.ind.br
Address
o DATACOM
o CEP: 90230-220
CONVENTIONS
In order to improve the agreement, the following conventions are made throughout this manual:
Command or Button - Always that some reference to a command, a button or a software menu is
made, this indication will be in italic.
# Commands and messages from terminal screens are presented in not-
formatted text, preceded from #.
Notes give an explanation about some topic in the foregoing paragraph.
This symbol means that this text is very important and, if the orientations were not correct followed, it may
cause damage or hazard.
This symbols means that, case the procedure was not correctly followed, may exist electrical shock risk.
Indicates that equipment or a part is ESDS (Electrostatic Discharge Sensitive). It should not be handled
without grounding wrist strap or equivalent.
This symbol means that this text is very important and, if the orientations were not correct followed, it may
cause damage or hazard.
This symbols means that, case the procedure was not correctly followed, may exist electrical shock risk.
Indicates that equipment or a part is ESDS (Electrostatic Discharge Sensitive). It should not be handled
without grounding wrist strap or equivalent.
IWEEE Directive Symbol (Applicable in the European Union and other European countries with separate
collection systems).This symbol on the product or its packaging indicates that this product must not be
disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will help
conserve natural resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your consumer waste equipment for
recycling, please contact your local city recycling office or the dealer from whom you originally purchased
the product
2. INTRODUCTION
2.1. Overview
EDD is a product of DATACOMs DmSwitch family geared to offer intelligent LAN/WAN demarcation services
for last mile Metro Ethernet access.
EDD enables managed access connections according to IEEE 802.3ah (Ethernet First Mile Operations,
Administration and Maintenance) and 802.1ag (Connectivity Fault Management), housed as a standalone
device with a full range AC/DC internal power supply. E1 ports are used for converting TDM data in Ethernet
packets (CESoP Bundles). WAN ports are to be used with SFP modules, allowing flexibility of optical
configurations and varying distances (SFP modules are sold separately).
Centralized management is achieved through DATACOMs DmView Network Management System, which
offers a graphical user interface to monitor the state and condition of the unit, network conditions as well as
configuration and inventory management functions.
EDD also offers additional QoS services which enables traffic prioritization and bandwidth availability control at
the demarcation point.
Fail Speed
Link
Speed
1
ALARM 1 3 5 SERIES II
When performing installation and maintenance operations of optical fibers, do not stand close or look
directly into the fiber outlet with unprotected eyes.
Electrostatic generated by human body may damage the electrostatic sensitive components on the
equipment.
AC/DC POWER
Clock IN/OUT Port 1/5 Port 2/6 Port 3/7 Port 4/8
AIR EXIT
Figure 6. Rear view of 2104G2-EDD E1
2.6.1. Software
Software information is available in a separated guide.
2.6.2. Hardware
2104G2-EDD E1
GBE ports 4 x 10/100/1000Base-T
Optical Ports (SFP) 2 x 1000Base-X
E1 ports 8
MAC Address table 8k
Power AC/DC Full range
Packet Buffer 128k
Flash 16MB
SDRAM 64MB
Table 5. Hardware 2104G2-EDD E1
3. MAKING CONNECTIONS
Use Unshielded Twisted-Pair (UTP) or Shielded Twisted-Pair (STP) cables with RJ45 connectors. Connect one
end of the cable directly in the switch port and the other in the other network device.
Check Table 6 to make sure the cables that are being used for the network are the correct ones.
1. Insert the SFP transceiver into any SFP cage of the switch. There's only one orientation that the
module can be plugged. The optical connector must face outward. The slot connector must face down for the
upper bays, and up for the lower bays.
2. Slide the module into the slot and press firmly to ensure it is securely placed.
Inserting or removing an SFP module can be done without powering off the switch. SFP transceivers are
hot-swappable, but make sure there are no network optical fibers connected to the module before
removing it! (Remove optical fibers before removing SFP modules).
After this, attach the security locker according to the figure below:
SFP modules that can be used with EDD and each respective maximum fiber length are described in the tables
below:
These modules are the most commonly used. Contact technical support for the complete and updated
SFPs module list.
Signals over optical fiber are transmitted via lasers. Although the lasers are compliant with the
requirements of Class 1 Laser Products and are eye safe in normal conditions, never look directly at a
transmit port when it is turned on.
One 2104G2-EDD E1
Choose a location where RJ45 and SFP ports can be easily reached, allowing LEDs to be
visible.
EDD box is made of plastic, so dont put heavier equipments over it.
Sites temperature should be kept within 0C to 55C and its humidity within 10 to 90% non-
condensing.
Do not block airflow exit so provide approximately 5 centimeters (2 inches) of space on all sides
of the device.
Before connecting any cable to the equipment, be sure that the grounding system is functional.
After installing the switch, plug one end of IEC-320 standard power cable into the AC receptacle located
at the rear panel of the switch (see in Figure 6) and the other end into a local power source outlet. Power
LED should light, indicating the switch is correctly powered.
If DC power is used, power cable must be cut close to the AC sockets connection plug and connected in
a way that the socket central pin corresponds to protection ground and the other 2 pins for the power
supply (see in Figure 11). Equipments shelf is connected directly to the protection ground.
Figure 11. AC/DC Power Supply Connector
5. TECHNICAL SPECIFICATION
5.3. Weight
Models Weight
2104G2-EDD E1 0.715 kg (1.57 pounds)
Table 10. Weight
5.4. Dimensions
Models Dimensions
2104G2-EDD E1 44mm height, 195mm width, 200mm depth
Table 11. Dimensions
6. ANNEX I RJ45-4XIECF CABLE
6.1. Overview
RJ45-4XIECF cable converts each RJ45 connector located in rear of EDD in 4 IEC E1 connectors. The
size of cable may be customized.
RJ45 CONNECTOR
E1-IEC CONNECTORS
Figure 12. RJ45-4XIECF cable
6.2. Pinout