Академический Документы
Профессиональный Документы
Культура Документы
Abstract: This paper deals with an efficient analytical scheme for the analysis of stress and displacement fields
of boundary-value problemsof plane elasticity with mixed boundary conditions and material discontinuity. More
specifically, the mechanical behavior of a stiffened panel with an edge crack is analyzed under the influence of
axial loading, using a new analytical scheme. Earlier mathematical models of elasticity were very deficient in
handling the practical stress problems of solid mechanics. Analytical methods of solution have not gained that
much popularity in the field of stress analysis, mainly because of the inability of dealing with mixed boundary
conditions, irregular boundary shapes, and material discontinuity.
Keywords: Analytical model, axial loading, displacement potential, edge crack, stiffened panel.
I. Introduction
The analysis of mechanical behavior of structural components containing cracks drew the attention of
researchers since late 1890s. The view of crack analysis from mechanics view point was stated by Love in his
authoritative work on Theory of Elasticity in the 1890s by The conditions of rupture are but vaguely
understood, ... At that time Coulomb and Mohrs theories were followed by many without considering the
effects of flaws or cracks in materials.
Historically, some attempts were tried in the early 1900s but here only those connected to and leading
directly to current methods will be mentioned. The first was that of Inglis [1] in 1913. He used elliptical-
hyperbolic coordinates to solve the elastic stress problem of an elliptical hole in a plate. Then he tried to
degenerate the ellipse into a crack and his stress solution near the crack tip became unresolved.
Griffith [2] made use of the stress solution provided by Inglis for a plate under uniform tension with an
elliptical hole, which could be degenerated into a crack. However, neither Griffin nor his predecessors had the
knowledge of stress fields near cracks, which is now available. Sneddon [online] was the first to give stress-field
expansions for crack tips for two individual examples.
As far as the earlier researches are concerned, the attempts of Williams [3] and Irwin [4-5] for finding
analytical solutions for the stress and displacement fields near the crack tip are noticeable. In these analyses, an
Airy stress function [6] has been suggested to derive a general governing equation for predicting the state of
stress near the tip of a part-through crack in an infinite thin plate. Later Sedov presented the general solution for
an internal crack in an infinite plate using plane stress assumption [7]. On the other hand, these solutions for
stress distribution near the crack tip allowed the researchers to analyze the cracked structures from the
standpoint of fracture mechanics. As a result, a number of successful attempts have been made to determine
stress intensity factors based on the elastic stress distribution near the crack tip [8-10].
Even though several attempts have been made to obtain analytical solutions for the stress state in
cracked bodies, closed form analytical solutions are only found for cracks in semi-infinite or infinitely large
bodies under pure tension. It is worth mentioning that most of the solutions so obtained are only valid in the
vicinity of the crack tip, which, in turn, identifies them to be inadequate for regions away from the crack tip.
However, engineering structures in practice are of boundary value types and, usually encounter different types
of physical conditions and shapes as well as cracks tend to occur in regions of high stress concentration. It is,
therefore, important to take into account the effect of nearby boundaries appropriately. In fact, the necessity of
finding stresses and displacements in cracked bodies in real cases persuades the researchers to develop
numerical and empirical methods. The most important and useful forms of such studies has been collected by
Tada et. al. [11].
The crack problem in finite bodies becomes more complex for the case of stiffened structures. As a
result, serious attempts have hardly been made so far in the literature that can provide exact analytical solutions
for the stresses in cracked stiffened structures with finite dimensions. Even successful attempts for analyzing
edge cracks in semi-infinite stiffened structures are very few; the work of Shkarayev and Moyer can be cited as
an example [12]. These analyses are mainly handled by approximate numerical techniques, as in most cases the
available mathematical models are inadequate to provide exact analytical solutions to them. As a result, several
numerical techniques, such as, matrix force method, finite element method, dual boundary element method, etc.
www.ijesi.org 1 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
have been found to apply extensively for the solution of crack problems in stiffened structures [13-15]. Ratwani
and Wilham studied the influence of biaxial loading in stiffened panels using the FEM [14].
In the present study, the elastic behavior of cracked stiffened panels of finite dimensions is investigated
under flexural and axial loading through a new analytical scheme based on a single scalar potential [16-17]. In
the potential function boundary modeling approach, the elastic problem is formulated in terms of a single scalar
potential of space variables, defined in terms of the displacement components of plane elasticity, which has to
satisfy a single fourth-order partial differential equation of equilibrium. The relevant displacement and stress
components are derived into infinite series using Fourier integral with coincided boundary conditions along with
the physical boundary conditions. Special cares are taken to model the physical conditions at different segments
of the bounding surface of the panel in a reasonable and justifiable manner. The panel is assumed to be stiffened
along the two opposing longitudinal edges, in which use of both the axial and lateral stiffeners is investigated
separately. The edge crack of zero-degree notch angle is considered to be located at mid-length position of the
panel. For checking the reliability as well as appropriateness of the present solution, numerical solutions of
cracked stiffened panels are obtained by finite element method with the help of standard commercial software.
+ + =0
x 2 2 xy 2 y 2 (1a)
uy 1+ m ux 1- m ux
2 2 2
+ + =0
y 2 2 xy 2 x 2 (1b)
where m is the Poissons ratio of the material. The stress components are calculated from the following
equations
E u x u y
xx
1 x y
2
(2a)
E u x u y
yy
1 x y
2
(2b)
u x
E u y
2 1 y
xy
x
(2c)
In the displacement potential function formulation, the displacement components are expressed in terms of a
potential y of space variables as follows:
2 2 2
ux 1 2
3
x xy y
2 2
(3a)
2 2 2
uy 4
5
6
x xy y
2 2
(3b)
Here, a s are unknown material constants.
Combining Equations (1) and (3), we obtain the equilibrium equations in terms of the function y (x, y), which
are
4y 1+ m 4y 1- m 1+ m 4y
a1 + a + a + a + a + a 5
x 4 2 x 3y 2 2 x 2y 2
2 4 3 1
1- m 1+ m 4y 1- m 4y
+ a 2 +
6a + a 3 =0
2 2 xy3 2 y 4 (4a)
www.ijesi.org 2 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
1- m 4y 1+ m 1- m 4y 1+ m 4y
a4 4 + a1 + a5 3 + a3 + a5
2 x 2 2 x y 2 xy3
1+ m 1- m 4y 4y
+ a 2 + a4 + a6 2 2 + a 6 4 = 0
2 2 x y y (4b)
The constants, a s are chosen here in such a way that Equation (4a) is automatically satisfied under all
circumstances. This will happen when coefficients of all the derivatives present in equation (4a) are individually
zero. That is, when
a1 = a3 = a5 = 0 (5a)
1+ m
a2 + a4 =0
2 (5b)
1- m 1+ m
a2 + a6 =0
2 2 (5c)
Thus for y to be a solution of the stress problem, it has to satisfy Equation (4b) only. However, the
values of a s must be known in advance. Here, we have basically two equations (Equations (5b) and (5c)) for
determining three unknown a s. An arbitrary value is thus assigned to any one of these three unknowns and the
remaining a s are solved from Equation (5). Assuming a 2 =1, the values of a s thus obtained, are as follows:
a1 = a3 = a5 = 0 (6a)
a 2 =1 (6b)
2
a4 = -
1+ m (6c)
1- m
a6 =
1+ m (6d)
When the above values of a s are substituted in Equation (4b), the governing differential equation for the
solution of two-dimensional problems becomes
4 4 4
2 0
x x y y
4 2 2 4
(7)
The problem is thus reduced to the solution of a single function y (x, y) from the governing bi-
harmonic equation (7), along with the specified boundary conditions. Thus, the computational work in solving
any problem remains the same in the present case as it was in the case of stress function formulation [18], since
both of them have to satisfy the same bi-harmonic equation. But the y - formulation is free from the inability of
the stress function formulation in handling the mixed boundary conditions.
Expressions of boundary conditions in terms of the function, y
2
u x x, y
xy
(8a)
2 2
1
u y x, y 2 1 2
1 x y
2
(8b)
3 2
E
x, y 2
1
xx
x y y
2 2
(8c)
E y y 3 3
s yy ( x, y) = - ( 2 + m ) 2 + 3 (8d)
(1+ m ) x y y
2
www.ijesi.org 3 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
3 3
E
x, y 2
1
xy
x xy
2 3
(8e)
www.ijesi.org 4 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
Now combining equation (8) and (9) the expressions for the relevant stress and displacement components are
obtained as
ux ( x, y) = - Amaea x + Bm (a x +1) ea x - Cma e-a x - Dm (a x -1) e-a x a sin a y (13)
m=1
-1 Am (1+ m ) a e + Bm (a x + ma x + 4) a e
2 ax ax
uy ( x, y) =
(1+ m ) m=1 +Cm (1+ m ) a 2e-a x + Dm (a x + ma x - 4) a e-a x
cos a y
(14)
-E Ama (1+ m ) e + Bm (a x + ma x + 2) e
ax ax
2
s xx ( x, y) = a 2
sin a y (15)
( ) m=1 m ( )
1+ m +C a 1+ m e -a x
+ Dm(a x + ma x - 2 )
e -a x
-E Ama ( -1- m ) e + Bm (-a x - ma x - 2m - 4) e + 2
ax ax
2
s yy ( x, y) = a sin a y (16)
(1+ m ) m=1 Cma (-1- m ) e + Dm (-a y - ma x + 2m + 4) e
-a x -a x
-E Am (1+ m ) a e + Bm (a x + ma x + m + 3) e
ax ax
2
s xy ( x, y) = a 2
cos a y (17)
(1+ m ) m=1 -Cm (1+ m ) ae-a x - Dm (a x + ma x - m - 3) e-a x
Now, the axial loading on the right edge of the panel can be taken as Fourier series in the following manner:
s xx (b, y) = s 0 = Em sin a y (18)
m=1
To satisfy the boundary condition as well as based on the loading distribution, Fourier sine series have been
considered for the analysis.
2 a
Em =
a0
s 0 sin(a y)dy
2s 0 a
=
a 0
sin(a y)dy
2s
= 0 [-cos(a y)]0a
aa
2s 0
= [1- cos(mp )], where m = 1, 2, 3, 4, 5 .
mp
Due to symmetry, the axial displacement at the left edge from 0 to (a-h) is zero. But at the crack surface, the
distribution of the axial displacement can be expressed as the Fourier series in the following manner:
3 3
ux (0, y) = a0 + ai cos(i * w * y) + bi sin(i * w * y) = I m sin(a y) (19)
i=1 i=1 m=1
The curve fitted equation as Fourier series up to 7th term have been considered. This is because of up to 7 th term
we always achieve R2 value above 0.99. If we increase the term it will make the mathematical calculation more
complicated.
Here
2 a 3 3
Im = 0
a a-h
(a + ai cos(i * w * y) + bi sin(i * w * y))sin(a y)dy
i=1 i=1
By applying boundary conditions to equations (13) to (17), the four equations obtained can be realized in a
simplified matrix form for the solution of unknown terms like Am , Bm , Cm and Dm as follows:
www.ijesi.org 5 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
FF2 = (a b + ma b + m + 3) eab
FF3 = -a (1+ m ) e-ab
FF4 = - (a b + ma b - m - 3) e-ab
HH1 = -a 2
HH 2 = -a
HH 3 = a 2
KK1 = Z11a (1+ m ) eab
KK2 = Z11 (a b + ma b + 2) eab
KK3 = Z11a (1+ m ) e-ab
KK 4 = Z11 (ab + mab - 2) e-ab
-Ea 2
Z11 =
(1+ m )2
Solution of the above matrix Eq. (20) yields the unknown constants Am , Bm , Cm and Dm which are used to
obtain the complete solutions of the stress and displacement components through equation (13) to (17).
i. Displacement Field
In Fig. 3 the distribution of the normalized distribution component ux / b at different sections of panel
is illustrated. The distribution of this displacement component is parabolic except near the region of the crack
edge. Due to symmetry no axial displacement is happened at mid-section along the ligament (at x = 0) but at
crack surface since the panel is free, axial displacement happens and it is almost parabolic. Below the region x/b
0.4 it is not symmetric but bottom skewed because of the presence of the crack. As the axial load is applied on
the right lateral edge, the displacement will be maximum at section x = 0.5, and it will gradually decrease as
moving towards the left supporting edge. Zero value of ux at the stiffened edges confirms the satisfaction of
boundary condition of those ends.
Fig. 4 presents the normalized displacement component uy / a as a function of y/a at different
sections of the panel. The displacement component varies almost symmetrically from one stiffener to another
www.ijesi.org 6 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
with a zero value at y/a = 0.5 for x / b 0.1. But at x / b = 0 due to presence of crack some fluctuation of
displacement happens at y / a = 0.8 thats why the distribution is anti-symmetric. It is observed that the
displacement component uy varies from a positive value at the lower stiffener to a negative value at the upper
stiffener and the opposite happens at the other region.
www.ijesi.org 7 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
IV. Figures
Fig. 2 Geometry and loading of a stiffened cracked panel: (a) Full model of the panel (b) symmetric model of
the panel.
Fig. 3 Distribution of normalized axial displacement at different sections of the steel panel (h/a=0.2, b/a = 1).
www.ijesi.org 8 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
Fig. 4 Distribution of normalized lateral displacement at different sections of the steel panel (h/a = 0.2, b/a = 1).
Fig. 5 Distribution of normalized axial stress at different sections of the steel panel (h/a = 0.2, b/a = 1).
Fig. 6 Distribution of normalized lateral stress at different sections of the steel panel (h/a = 0.2, b/a = 1).
www.ijesi.org 9 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
Fig. 7 Distribution of normalized shear stress at different sections of the steel panel (h/a = 0.2, b/a = 1).
Fig. 8 Effect of crack length on the axial stress component at x/b = 0.0 (b/a = 1).
Fig. 9 Effect of crack length on the lateral stress component atx/b = 0.0 (b/a = 1).
www.ijesi.org 10 | Page
A Displacement-Potential Scheme To Stress Analysis Of A Cracked Stiffened Panel Under Axial
Fig. 10 Effect of crack length on the shear stress component at x/b = 0.5 (b/a = 1).
V. Conclusion
The analytical solution for the elastic field of stiffened panels with an edge crack subjected to different
kinds of loading has been successfully derived. Appropriate alternative expression for one of the boundary
conditions at crack surface has been derived from the numerical solution of the problem performance in terms of
the same potential function. Having appropriate analytical expressions for all the necessary boundary conditions,
an efficient and accurate analytical scheme has been developed in terms of a potential function defined in terms
of displacement components for the analysis of elastic field of cracked stiffened panels.
References
[1]. Inglis, C. E., Stresses in a plate due to the presence of cracks and sharp corners,Transactions of the Institution of Naval Architects,
London, England, 60, 1913, 219.
[2]. Griffith, A. A., The phenomena of rupture and flow in solids, Philosophical Transactions of the Royal Society of London, England,
221, 1921, 163-198.
[3]. Williams, M. L., On the stress distribution at the base of a stationary crack, Journal of Applied Mechanics,24, 1957, 109-114.
[4]. Irwin, G. R., Encyclopedia of Physics,6, Springer, Berlin, 1958.
[5]. Irwin, G. R., The crack extension force for a part through crack in a plate, Journal of Applied Mechanics, 29, 1962, 651654.
[6]. Timoshenko, S. P. and Goodier, J. N., Theory of Elasticity (3rd Edition, McGraw Hill Book Company, New York, 1970).
[7]. Sedov, L. I., A course in continuum mechanics, 4, (Groningen, Volters-Noordhoff, 1972).
[8]. Bowie, O. L., and Neal, D. M., Single edge crack in rectangular tensile sheet, Journal Applied Mechanics, 708,1965, 708-710.
[9]. Lhermet, G., Vessiere, G., and Bahuaud, J., Determination of stress intensity factors from stress concentrations for v-notched
beams, Engineering Fracture Mechanics, 28 (3), 1987, 331-343.
[10]. Ebrahimi, A., Behzad, M., and Meghdari, A., A bending theory for beams with vertical edge crack, International Journal of
Mechanical Sciences, 52, 2010, 904-913.
[11]. Tada, H., Paris, P. C., and Irvin, G. R., The stress analysis of cracks handbook, (3rd Edition, Professional Engineering Publishing,
2000).
[12]. Shkarayev, S. V., and Moyer, E. T., Edge cracks in stiffened panels, Engineering Fracture Mechanics, 27(2), 1987, 127-134.
[13]. Swift,T., DevelopmentofthefailsafedesignfeaturesoftheDc-10 damagetolerancein aircraft structures, ASTM STP, 486, 1971, 164-
213.
[14]. Ratwami, M. M., and Wilhem, D. P., Influence of bi-axial loading on analysis of cracked stiffened panels, Engineering Fracture
Mechanics, 11, 1979, 585-593.
[15]. Salgado,N.K.,andAliabadi, M. H., Theapplicationofthedualboundaryelementmethod to the analysis of cracked stiffened panels,
Engineering Fracture Mechanics, 54 (1), 1996, 91-105.
[16]. Ahmed, S. R., Khan, M. R., Islam, K. M. S., and Uddin, M. W., Investigation of stresses at the fixed end of deep cantilever beams,
Computers & Structures, 69, 1998, 329338.
[17]. Ahmed, S. R., Hossain, M. Z., and Uddin, M. W., A general mathematical formulation for finite-difference solution of mixed-
www.ijesi.org 11 | Page