Академический Документы
Профессиональный Документы
Культура Документы
detected.
Waster toner full detection sensor is
faulty. - Check the connector of the waster
E019- The waste toner full state was toner full sensor. - Replace the waste
0002 detected continuously for five or more toner full sensor. - Replace the DC
seconds while the main motor was controller PCB.
turning.
Erroneous connection to duplex unit
- Check the connectors of the duplex
Disconnection of the duplex unit was
E052- unit and DC controller PCB. - Replace
detected after power-on, detection of
0000 the duplex controller PCB. - Replace the
normal connection to the duplex unit,
DC controller PCB.
and start of communication
- Check the connector of the BD
E100- BD detection PCB failure detection PCB. - Replace the laser
0000 The BD detection PCB is faulty scanner unit. - Replace the DC
controller PCB.
Image processor PCB failure - Putting the switch on/off of the power
E196-
Error on writing and readout ROM of supply. - Replace the image processor
0001
image processor PCB (mainn ROM). PCB.
Image processor PCB failure - Putting the switch on/off of the power
E196-
Error on writing and readout ROM of supply. - Replace the image processor
0002
image processor PCB (option ROM). PCB.
- Check the connectors of the DC
Printer engine communication error
controller PCB and image processor
E197- Erroneous communication between
PCB. - Replace the DC controller PCB
0000 the DC controller PCB and image
for normal connection. - Replace the
processor PCB was detected.
image processor PCB.
standard tray was operated, but it did not standard tray HP sensor. - Replace
reach the sensor within 300 ms the standard tray clock sensor. -
Replace the standard tray shift motor.
- Replace the finisher controller PCB.
- Check the connector of the standard
- Standard tray shift motor or finisher
tray HP sensor. - Check the connector
controller PCB failure
of the standard tray clock sensor. -
- Standard tray HP sensor failure -
Check the connector of the standard
E540- Standard tray clock sensor failure -
tray shift motor. - Replace the
0005 Standard tray shift motor load failure The
standard tray HP sensor. - Replace
encoder clock signal was not detected
the standard tray clock sensor. -
two or more times when the standard
Replace the standard tray shift motor.
tray was operated for 300 ms.
- Replace the finisher controller PCB.
- Check the connector of the optional
- Optional tray motor or finisher controller tray HP sensor. - Check the connector
PCB failure of the optional tray clock sensor. -
- Optional tray HP sensor failure - Check the connector of the optional
E542-
Optional tray clock sensor failure - tray shift motor. - Replace the optional
0001
Optional tray shift motor load failure The tray HP sensor. - Replace the optional
optional tray was operated, but the paper tray clock sensor. - Replace the
surface was not detected. optional tray shift motor. - Replace the
finisher controller PCB.
- Check the connector of the optional
- Optional tray motor or finisher controller tray HP sensor. - Check the connector
PCB failure of the optional tray clock sensor. -
- Optional tray HP sensor failure - Check the connector of the optional
E542-
Optional tray clock sensor failure - tray shift motor. - Replace the optional
0002
Optional tray shift motor load failure tray HP sensor. - Replace the optional
Cannot move (to the pickup position) tray clock sensor. - Replace the
within the specified time. optional tray shift motor. - Replace the
finisher controller PCB.
- Check the connector of the optional
- Optional tray motor or finisher controller
tray HP sensor. - Check the connector
PCB failure
of the optional tray clock sensor. -
- Optional tray HP sensor failure -
Check the connector of the optional
E542- Optional tray clock sensor failure -
tray shift motor. - Replace the optional
0003 Optional tray shift motor load failure The
tray HP sensor. - Replace the optional
optional tray was moved upward, but it
tray clock sensor. - Replace the
did not reach the HP sensor within 3000
optional tray shift motor. - Replace the
ms.
finisher controller PCB.
- Optional tray motor or finisher controller - Check the connector of the optional
E542- PCB failure tray HP sensor. - Check the connector
0005 - Optional tray HP sensor failure - of the optional tray clock sensor. -
Optional tray clock sensor failure - Check the connector of the optional
5
Optional tray shift motor load failure The tray shift motor. - Replace the optional
encoder clock signal was not detected tray HP sensor. - Replace the optional
two or more times when the optional tray tray clock sensor. - Replace the
was operated for 300 ms. optional tray shift motor. - Replace the
finisher controller PCB.
- Stack delivery motor or finisher - Check the connector of the stack
controller PCB failure delivery HP sensor. - Check the
- Stack delivery HP sensor failure The connector of the stack delivery motor.
E575-
stack delivery motor was driven for 2000 - Check the connector of the stack
0001
ms in the stack delivery direction (HP delivery HP sensor. - Replace the
sensor approach direction), but the stack stack delivery motor. - Replace the
delivery HP sensor did not turn on. finisher controller PCB.
- Stack delivery motor or finisher - Check the connector of the stack
controller PCB failure delivery HP sensor. - Check the
- Stack delivery HP sensor failure The connector of the stack delivery motor.
E575-
stack delivery motor was driven for 2000 - Check the connector of the stack
0002
ms in the HP sensor escape direction, delivery HP sensor. - Replace the
but the stack delivery HP sensor did not stack delivery motor. - Replace the
turn off. finisher controller PCB.
6