TEACHING PLAN, 2015-2016 Subject: DESIGN OF MACHINE ELEMENTS-II Code: 302048 Class: TE (Mechanical)-Div:A Theory: 04 hrs / week
Lec Date Cumulative Status Justification
ture % Syllabus [Completed [If Not Topics to be covered No. Coverage /Not Completed] Completed] 01 15/12/2017 Introduction to Design OF Machine elements II syllabus UNIT I Spur Gears 02 19/12/2017 Gear Drives: Classification of gears, selection of types of gears, desirable properties, 03 20/12/2017 selection of gear materials, standard gear tooth systems 04 23/12/2017 modes of gear tooth failures methods of gear lubrication 05 24/12/2017 Spur Gears: Number of teeth and face width, constructional details of gear wheel 06 26/12/2017 force analysis(Theoretical Treatment) ,beam strength (Lewis) equation, 07 27/12/2017 velocity factor, service factor, load concentration factor 16% 08 31/12/2017 effective load on gear, wear strength (Buckinghams) equation UNIT II 30Helical and Bevel Gears 09 2/01/2017 Helical Gear: Transverse and normal module, , 10 3/01/2017 virtual no of teeth, force analysis 11 9/01/2017 beam and wear strengths, 12 10/01/2017 effective load on gear tooth, estimation of dynamic tooth load by velocity factor and Buckinghams equation 13 13/01/2017 Bevel Gears: Straight tooth bevel gear terminology and geometric relationship formative number of teeth 14 14/01/2017 force analysis, design criteria of bevel gears, beam and wear strengths 15 16/01/2017 Dynamic tooth load by velocity factor and Buckinghams 33% equation, 16 20/01/2017 design of straight tooth bevel gears, selection of materials for bevel gears 17 21/01/2017 Introduction to spiral bevel gears and hypoid gears and comparison with straight tooth bevel gears,Mounting of Bevel Gears UNIT III Rolling Contact Bearings 18 23/01/2017 Types of rolling contact bearings 19 24/01/2017 Static and dynamic load carrying capacities 20 27/01/2017 Stribecks equation, equivalent bearing load, load-life relationship, bearing life 50% 21 28/01/2017 Selection of rolling contact bearings from manufacturers catalogue 22 30/01/2017 Taper roller bearing, design for cyclic loads and speed Bearing with probability of survival other than 90% 23 31/01/2017 Lubrication and mounting of bearings, preloading of rolling contact bearings 24 3/02/2017 Types of failure in rolling contact bearings causes and remedies, selection of oil seals for shafts 25 4/02/2017 Selection of bearings for different automotive IC engines, ACAD-R-05, Rev.: 00 Date: 03-07-2010 AMRUTVAHINI COLLEGE OF ENGINEERING, SANGAMNER
4wheels and steering.
UNIT IV Worm Gears 26 6/02/2017 Worm and worm gear terminology 27 7/02/2017 Geometrical relationship, types of worm and worm gears, 28 10/02/2017 Standard dimensions, 29 11/02/2017 Force analysis of worm gear drives 30 13/02/2017 Friction in worm gears and its efficiency, 66% 31 14/02/2017 Strength and wear ratings of worm gears 32 17/02/2017 Thermal consideration in worm gear drive 33 18/02/2017 Types of failures in worm gearing, methods of lubrication UNIT V Belt Ropes and Chain Drive 34 20/02/2017 Belt Drive: Materials and construction of flat belt and V belt drive, Geometric relationship for length of belt drive 35 21/02/2017 Power ratings of belts 36 25/02/2017 Concept of slip and creep, initial tension, effect of centrifugal tension 37 27/02/2017 Max power condition 38 28/02/2017 Selection of flat belt from manufacturers catalogue 39 3/03/2017 Belt tensioning methods, Relative advantages and 84% disadvantages of flat belt and v belt, construction and applications of Timing belts. 40 4/03/2017 Wire ropes: construction of wire ropes, lay, stress in wire ropes, selection of wire ropes, rope drum construction and designs 41 14/03/2017 Chain Drives: Types of power transmission chains, geometry of chain, polygon effect in chain, modes of failure of chain, lubrication of chain UNIT VI Sliding contact Bearings 42 17/03/2017 Lubricating oils Properties, additives for mineral oils, selection of lubricants 43 18/03/2017 selection of bearing materials 44 20/03/2017 Theory of hydrodynamic lubrication 45 21/03/2017 mechanism of pressure development in oil film 100% 46 24/03/2017 Two dimensional Reynolds equation 47 25/03/2017 Theory of infinitely long bearing 48 27/03/2017 Theory of infinitely short journal bearing 49 28/03/2017 Summerfield number, Raimondi and Boyd method, temperature rise. 50 31/03/2017 Parameters of bearing design, length to diameter ratio, unit bearing pressure, radial clearance and minimum oil film thickness.