Академический Документы
Профессиональный Документы
Культура Документы
Workflow
Read and understand the "Safety Precautions" 1 Preparation & Installation 6 ETERNUS DX60/DX80 Setup
Area 7 Setting up the ETERNUS
before use.
2 Check the Package Contents DX60/DX80 to Support
"Safety Precautions"
3 Installation Maintenance
4 Cable Connection 8 Server Connection
5 Pre-Setup Preparation 9 Operation and Maintenance
The company names, product names and service names mentioned in this document are registered trademarks or trademarks of their respective companies.
Copyright 2009 FUJITSU LIMITED
The latest version of this document and the latest information about the ETERNUS DX60/DX80 is released in the following web-site. Access the following address if needed.
http://www.fujitsu.com/global/services/computing/storage/eternus/products/diskstorage/dx60-dx80/
Environmental conditions
Temperature: 5 40C
Humidity: 20 80%RH
Proceed to
"Package Contents"
next step
STEP Installation
The rack rail (bracket) needs to be attached to the rack and the ETERNUS DX60/DX80 mounted.
1. Adjust the rack rail (bracket) 3. Mount the ETERNUS DX60/DX80 in the rack.
size to fit the rack.
(Rear rack pillars) IMPORTANT Make sure to install or remove the enclosure
"L" is stamped on the inner to or from the rack by two or more people.
side of the left rack rail. Loosen the screws,
and adjust the rack rails to Multiple Drive Enclosures must be connected
the depth of the rack.
to the controller enclosure following the order
"R" is stamped on the inner of the "DE_No. label" numbers attached to
[Left] side of the right rack rail. each Drive Enclosure. The position of the
labels are in the positions shown below.
(Front rack pillars)
At the right side of the front of Between the EXP#0 and
the drive enclosure EXP#1 expanders at the rear
[Right] of the drive enclosure
DE_No. label
2. Attach the rack rails (brackets) to the rack. The size of the
ETERNUS DX60/DX80 is 2U.
[Screw location of the rack rail (bracket)]
Tighten the screws in the same locations on both the front and rear sides of the rack pillars
[Left] [Right]
4. Fasten the ETERNUS DX60/DX80 to the rack.
3rd position 3rd position
2U ETERNUS DX60/DX80
(M5 screws) (M5 screws) "3.2 Rack Installation" in the "User Guide"
1st position 1st position
(M5 screws) Base line of the (M5 screws)
ETERNUS DX60/DX80
Rack rail (bracket)
IMPORTANT The cables should never be bent, twisted or Example for connection of miniSAS cable
pulled. (when two Drive Enclosures are installed)
Rear view Cable
Drive Underside of
Controller
Enclosure the SAS (IN) side plug
Enclosure
The RMT port is on the left side, and MNT port Controller
The MNT port must always be connected. The The SAS (OUT) port is on the left side,
RMT port only needs to be connected when the remote and SAS (IN) port is on the right side.
Insert the connector with a mark on its
support connection is to be independent of the customer
underside in the SAS (OUT) port.
network.
Insert the connector with a mark on its underside in the
"4.2.1 LAN Cable Connection (For Operation Management)" in the
"User Guide" SAS (IN) port.
"4.2.5 MiniSAS Cable Connection (For Drive Enclosures)" in the "User
Fibre Channel Cables Guide"
"4.2.2 Fibre Channel Cable Connection (For Fibre Channel) " in the "User
Controller
Guide" Enclosure
2. Enter the following user name and password, and click the
[Logon] button to logon to the ETERNUS DX60/DX80.
User name: root
Password: root (Default)
Create RAID Group Configure Affinity Group
3. After logging on, the Storage System Status screen
Create Volume Define LUN Mapping
appears.
Define Host
Initial Setup "4.3.3 Configuration Wizard" in the"User Guide"
All necessary settings are complete, and the ETERNUS DX60/DX80 is now ready for normal operation.
Status check
The status of the ETERNUS DX60/DX80 should be regularly monitored by checking the LEDs and using the Web browser.
Data backup
Important data should be regularly backed up to a tape drive or similar device as a precaution against system failures.