Академический Документы
Профессиональный Документы
Культура Документы
PLUMBING
1. Water column that seals the escape of unhealthy gases in the sanitary drainage system.
a. Siphon level
b. Trap or water seal
c. Air lock
d. Air chamber
2. A type of vent installed to ventilate soil and waste pipe and connecting branches rather
than fixture traps.
a. Loop vent
b. Relief vent
c. Unit vent
d. Circuit vent
3. Refers to the pump that will discharge the waste in the sump and transfer it to the house
drain installed overhead.
a. Sewage ejector
b. Septic tank
c. Sludge
d. Scum
5. What do you call the tool specifically designed for use with faucet installation?
a. Basin wrench
b. Specialty faucet wrench
c. Faucet tool
d. None of the above
6. A pipe fitting with the interconnection of pipes for the purpose of easy connection when
needed.
a. Double bend
b. Union patent
c. Tee reducer
d. Bibcock
7. That portion of the vent pipe system which ventilates the main soil and waste stack and
connecting branches, rather than the fixture traps themselves.
a. Circuit vent
b. Main vent
c. Relief vent
d. Unit vent
e. Wet vent
Page 1 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
d. CISV
10.A pipe fitting usually short with inside thread used to connect pipes with outside threaded
ends is called:
a. Nipple
b. Coupling
c. Union
d. Cross pipe
13.Kind of pipe that is remarkably superior for embedment in concrete structure due to
having same material properties.
a. Cast iron pipe
b. Sewer pipe
c. Asbestos pipe
d. Lead pipe
14.One of the first steps in the selection of a suitable water supply is:
a. Budgetary cost
b. Water demand
c. Water potability
d. Topography
15.A pipe fitting to change in one single direction the flow of water.
a. Elbow
b. Cross tee
c. Wye
d. Coupling
Page 2 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
19.The term used in the construction industry to specify the installation of all pipes in a
plumbing system:
a. Roughing-in
b. Plumbing layout
c. Piping network
d. Piping works
21.Method of water treatment wherein denser objectionable elements settle on the bottom of
the basin for easy separation:
a. Filtration
b. Sedimentation
c. Filtering
d. Limestone strain
23.A passage under a road embankment or canal which allows for the flow of water:
a. Gutter
b. Irrigation pipe
c. Culvert
d. Water trench
Page 3 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
Page 4 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
28.It is used for control, isolation and repair of the water distribution system:
a. Valves
b. Fixture branch
c. Septic tank
d. Riser
29.It is the settling process wherein water is left in a large basin for a long period of time:
a. Chlorination
b. Sedimentation
c. Filtration
d. Precipitation
Page 5 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
34.A floor-mounted toilet is sealed to the drainage system using closet bolts and a:
a. Tube of caulking
b. Tub of putty
c. Wax seal
d. None of the above
36.It is draining of the water seal caused by foreign objects like thread or string suspended
and extended over the outlet arm of the trap.
a. Ventilation
b. Capillary action
c. Water closet
d. Drainage
38.What do you call the trade name for a combination of a wye and eight bend?
a. Sanitary tee
b. 45 wye
c. Sanitary cross
d. Combo
39.A full circle connected to a line illustrated in plan view of a piping system indicated that it
is a:
a. Pipe stubbing out
b. Pipe turning down
c. Pipe turning out
d. None of the above
40.A fitting constructed to prevent passage air, gas, and other elements through the pipe
without affecting the flow of water is called:
a. Trap
b. Check valve
c. Damper
d. Air lock
Page 6 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
41.The following is a list of purposes for providing a venting system in the plumbing system.
Which among these is not a purpose?
a. To carry combustible sewer gas out of the building
b. To enable drains to drain faster and better
c. To convey the foul smell present in the pipes
d. To protect the seal in the trap it serves
42.The water supply between the fixture supply pipe and the water distributing pipe.
a. Fixture branch
b. Service pipe
c. Valves
d. Water meter
48.A device that charges a predetermined volume of water to fixtures for plumbing purposes
and is activated by direct water pressure.
a. Flushing valve
b. Flushometer
c. Float valve
d. Check valve
Page 7 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
a. Corner tank
b. Lavatory
c. Closet bowls
d. Bath tub
51.It is installed to collect any spilled water or other liquids, remove them from the floor
surface and deliver them to either storm drain or a sanitary drain system.
a. Strain
b. Floor drain
c. Roof drain
d. Drain
52.A material that would not be appropriate in setting a fixture onto a cultured marble vanity
top.
a. Oil-based putties
b. Septic tank
c. Floor drain
d. Strap
53.A piece of trim that covers the whole where the pipe penetrates the wall.
a. Handicap
b. Strap
c. Escutcheon
d. Drench shower
54.It consists of a single course of masonry brick tied to the outside of any of the above-
mentioned framed structures.
a. Masonry
b. Masonry veneer
c. Roof beam
d. Sole plate
55.It is the conduit of passageway that connects a fuel-gas burning appliance to a vent or
chimney.
a. Masonry chimney
b. Draft hood
c. Wall chimney
d. Vent collector
56.These products use the water supply to hold a volume of water under pressure so when
the flush cycle starts, the contents of the sealed tank are directed to the bowl.
a. Grinder type
b. Water volume
c. Air-assisted product
d. Closet bowl
Page 8 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
57.A type of pipe connection in which a ball-shaped end is held in a cuplike shell and allows
movements in every direction.
a. Ball joint
b. Ball cock
c. Backflow
d. Bidet
58.An impairment of the quality of the potable waste which creates an actual hazard to the
public health through poisoning or spread of disease by sewage, industrial fluids or waste.
Also defined as high hazard.
a. Continuous waste
b. Downspout
c. Contamination
d. Dead-end
59.A term used to describe a soil or waste system where all pipings are threaded pipe tubing
or other such construction using recessed drainage fittings to correspond to the type of
fittings.
a. Durham system
b. Cesspool
c. Ferrule
d. Fixture
60.A water closet consisting of a continuous trough containing water. The trough extends
under two or more adjacent seats.
a. Lavatory
b. Leader
c. Local vent
d. Latrine
Page 9 of 11
CDEP PRE-BOARD EXAM (January 2012)
PLUMBING
Page 10 of 11
81.
82.Part III. True of False
83.
84. T 86.Stub-up is a rough-in pipe that protrudes up through a flow and serves
85. as a fixture.
87.
88. SPUD 90.Slip joint is a fixture connector used to complete a connection to a
89. china fixture and a flush valve; used mostly on commercial fixtures
such as toilets or urinals.
91.
92. DUG
WELL 94.Drilled well is a well that has been excavated.
95.
93.
96. T 98.Water hammer is caused by a moving body of water suddenly stopping
97. in a pipe.
99.
100. T 102. Brazing is a welding process that uses silver-based filler but does
101. not require flux.
103.
104. VALVE 106. Pipes are used to isolate and regulate portions of a piping system or
S the entire system.
105. 107.
108. AERAT 110. Airbreak is a device screwed into the end of a faucet spout that
OR mixes air into flowing water and controls flow to reduce splashing.
109. 111.
112. T 114. Fitting allowance is also known as fitting knockout.
113. 115.
116. POP- 118. The two most common drain assembly designs for lavatories are
UP & GRID pop-up and pop-out.
117. 119.
120. INTER
CEPTOR 122. Trap primer is a device installed in a drainage system to prevent
undesirable items or fluids such as grease, oil and sand.
121.
123.