Вы находитесь на странице: 1из 4

Industrial Engine C32 ACERT

708-1007 bkW/
950-1350 bhp 1800-2100 rpm

CATERPILLAR ENGINE
SPECIFICATIONS
V-12, 4-Stroke-Cycle Diesel
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 145 mm (5.71 in.)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . 162 mm (6.38 in.)
Displacement . . . . . . . . . . . . . . . 32.1 liters (1959 in3)
Aspiration. . . . . . . . . . . . . . . . . Turbocharged/ATAAC
Rotation (from flywheel end) . . . Counterclockwise
Engine Weight, Net Dry
(approximate) . . . . . . . . . . . . . . . 2435 kg (5368 lbs.)
(does not include twin turbo model)

Image shown may not


reflect actual engine

FEATURES
Emissions Full Range of Attachments
Meets Tier 2 emissions requirements. Tier 2 Wide range of bolt-on system expansion
refers to EPA (U.S.) standards. attachments, factory designed and tested.
Worldwide Supplier Capability Unmatched Product Support Offered Through
Caterpillar Worldwide Caterpillar Dealer Network
Casts engine blocks, heads, and cylinder liners More than 1,800 dealer outlets
Machines critical components Caterpillar factory-trained dealer technicians
Assembles complete engine service every aspect of your industrial engine
Ownership of these manufacturing processes 99.7% of parts orders filled within 24 hours
enables Caterpillar to produce high quality, worldwide
dependable product. Caterpillar parts and labor warranty
Factory-designed systems built at Caterpillar Preventive maintenance agreements available
ISO 9001:2000 certified facilities. for repair before failure options
Testing Scheduled Oil Sampling program matches your
Prototype testing on every model oil sample against Caterpillar set standards to
proves computer design determine:
verifies system torsional stability internal engine component condition
tests functionality on every model presence of unwanted fluids
Every Caterpillar engine is dynamometer presence of combustion by-products
tested under full load to ensure proper engine
performance. Web Site
For additional information on all your power
requirements, visit www.cat-industrial.com.

LEHH5116-03 Page 1 of 4
Industrial Engine
708-1007 bkW/
C32 ACERT 950-1350 bhp

STANDARD ENGINE EQUIPMENT


Air Inlet System Flywheels and Flywheel Housing
Air-to-air aftercooled (ATAAC) SAE No. 0 or SAE No. 1 flywheel housing
Twin turbo
Fuel System
Control System MEUI injection
Electronic governing, PTO speed control Fuel filter, secondary (2 micron high
Programmable ratings performance)
Cold mode start strategy Fuel transfer pump
Automatic altitude compensation Fuel priming pump
Power compensation for fuel temperature ACERT Technology
Programmable low and high idle and total
Lube System
engine limit
Crankcase breather
Electronic diagnostics and fault logging
Oil cooler
Engine monitoring system
Oil filler
J1939 Broadcast (diagnostic and engine status)
Oil filter
ADEM A4
Oil pan front sump
Cooling System Oil dipstick
Thermostats and housing, vertical outlet Oil pump (gear driven)
Jacket water pump, centrifugal
General
Water pump, inlet
Paint, Caterpillar yellow
Exhaust System Vibration damper
Exhaust manifold, dry Lifting eyes
Optional exhaust outlet

LEHH5116-03 Page 2 of 4
Industrial Engine
708-1007 bkW/
C32 ACERT 950-1350 bhp

PERFORMANCE CURVES
1200 1600

1400
1000

1200

800
1000

Power (bhp)
Power (bkW)

E
600 D 800
C
B 600
400

400

200
200

0 0
1000 1200 1400 1600 1800 2000 2200 2400
rpm

7000 5000

4500
6000
E
4000

5000
D
C 3500
Torque (Nm)

Torque (lb-ft)

3000
4000 B

2500

3000
2000

1500
2000

1000

1000
500

0 0
1000 1200 1400 1600 1800 2000 2200 2400
rpm

Length 2083 mm (82 in.)


Width 1473 mm (58 in.)
Height 1499 mm (59 in.)

LEHH5116-03 Page 3 of 4
Industrial Engine
708-1007 bkW/
C32 ACERT 950-1350 bhp

INDUSTRIAL RATINGS AND CONDITIONS


IND-B Ratings are based on SAE J1995, inlet air standard
For service where power and/or speed are cyclic conditions of 99 kPa (29.31 in. Hg) dry barometer
(time at full load not to exceed 80%). and 25C (77F) temperature. Performance
measured using a standard fuel with fuel gravity
IND-C (Intermittent)
of 35 API having a lower heating value of 42,780
Intermittent service where maximum power
kJ/kg (18,390 btu/lb) when used at 29 C (84.2 F)
and/or speed are cyclic (time at full load not to
with a density of 838.9 g/L.
exceed 50%).
The corrected performance values shown for
IND-D
Caterpillar engines will approximate the values
For service where maximum power is required for
obtained when the observed performance data is
periodic overloads.
corrected to SAE J1995, ISO 3046-2, 8665, 2288,
IND-E 9249, and 1585, EEC 80/1269 and DIN 70020
For service where maximum power is required for standard reference conditions.
a short time for initial starting or sudden overload.
For emergency service where standard power is
unavailable.

Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication.
CAT, CATERPILLAR, ACERT, ADEM, their respective logos and Caterpillar Yellow, as well as corporate and product
identity used herein, are trademarks of Caterpillar and may not be used without permission.
2006 Caterpillar
LEHH5116-03 (1-06) Printed in U.S.A. All rights reserved.

Вам также может понравиться