Академический Документы
Профессиональный Документы
Культура Документы
GDS-2000 Series
USER MANUAL
GW INSTEK PART NO. 82DS-22040MB1
SAVE/RECALL ................................................................118
File Format/Utility ............................. 119
Quick Save (HardCopy)...................... 125
3
SAFETY INSTRUCTIONS GDS-2000 Series User Manual
Safety Guidelines
CAUTION
Make sure the BNC input voltage does not
exceed 300V peak.
Never connect a hazardous live voltage to the
ground side of the BNC connectors. It might
This chapter contains important safety instructions
lead to fire and electric shock.
that you must follow when operating GDS-2000
and when keeping it in storage. Read the Do not place any heavy object on GDS-2000.
following before any operation to insure your Avoid severe impacts or rough handling that
safety and to keep the best condition for GDS-2000. leads to damaging GDS-2000.
Do not discharge static electricity to GDS-2000.
Safety Symbols Use only mating connectors, not bare wires, for
the terminals.
These safety symbols may appear in this manual or on GDS-2000.
Do not block the cooling fan opening.
Warning: Identifies conditions or practices that Do not perform measurement at power source
WARNING could result in injury or loss of life. and building installation site (Note below).
Do not disassemble GDS-2000 unless you are
Caution: Identifies conditions or practices that qualified.
CAUTION could result in damage to GDS-2000 or to other (Measurement categories) EN 61010-1:2001 specifies the
properties. measurement categories and their requirements as follows. GDS-
2000 falls under category II.
5 6
SAFETY INSTRUCTIONS GDS-2000 Series User Manual
7 8
GETTING STARTED GDS-2000 Series User Manual
9 10
GETTING STARTED GDS-2000 Series User Manual
11 12
GETTING STARTED GDS-2000 Series User Manual
LCD display TFT color, 320 x 234 resolution, wide angle view
Appearance LCD display.
13 14
GETTING STARTED GDS-2000 Series User Manual
Cursor key Configures and runs cursor Vertical position Sets the vertical position of
measurements (page59). knob waveforms (page101).
Run/Stop key Freezes (Stop) or continues (Run) Ground terminal Accepts the DUT ground lead for
signal acquisition (page49). common ground.
Trigger menu key Configures trigger settings Math key Configures and runs math
(page105). operation (page63).
Trigger knob Sets trigger level (page105). USB host port TypeA, 1.1/2.0 compatible. Prints
out display image (page145) or
transfers data (page118).
Time/Div knob Selects the horizontal scale External trigger EXT TRIG
For 2ch model only. Accepts
(page95). input external trigger signal (page105).
Input impedance: 1M2%.
15 16
GETTING STARTED GDS-2000 Series User Manual
17 18
GETTING STARTED GDS-2000 Series User Manual
USB
Display RS-232C
GPIB (optional)
Power Interface Date/Time or Trigger Acquisition
source Memory Bar status mode Date/Time Current date and time (page116).
Interface Shows the active interface for remote connection For channel details, see page101.
(page148) and PC software connection.
19 20
GETTING STARTED GDS-2000 Series User Manual
Set Up Power up
21 22
GETTING STARTED GDS-2000 Series User Manual
2. Connect probe Connect the probe to Channel1 input terminal and 5. Compensate Turn the adjustment point on the probe to make
probe compensation signal output (2Vp-p, 1kHz probe the square waveform edge flat.
square wave).
Set the probe attenuation to x10.
G D S -2 1 0 4
X1
X10
x1 x10
23 24
QUICK REFERENCE GDS-2000 Series User Manual
F1 = Press F1
This chapter describes GDS-2000 menu tree, F1 = Press F1 repeatedly
shortcuts to major operations, built-in Help access,
F1 ~ F4 = Select one from F1 to F4 and press it
and default factory settings. Use them as a handy
reference to get a quick access to the functionality. F1VAR = Press F1, then use the Variable knob
Auto Set = Press the function key itself (AutoSet in this case)
Menu tree / Convention ..................................................... 26
shortcut Acquire key ..................................................... 26
Auto Set key .................................................... 26
Acquire key
Auto test/Stop key .......................................... 27 Select acquisition mode
Acquire
CH1 ~ 4 key .................................................... 27
F1~F3
Cursor key....................................................... 27 ACQUIRE
Select average number (only in
Display key...................................................... 28 Normal F 1 average mode)
Hardcopy key .................................................. 28
Peak F3
Help key ......................................................... 28 F 2
Detect
Select memory length
Horizontal menu key ....................................... 28 Average 2/ 4/ 8/ 16/ 32/
F 3 F5
64/ 128/ 256
Math key (1/2) ................................................ 29
Measure key (1/2) ........................................... 30
Program key (1/2) ........................................... 31 500/25000 (1CH)
Mem Leng 500/12500 (2CH)
F 5
Run/Stop key .................................................. 31 500 500/5000 (3/4CH)
Save/Recall key (1/9) ...................................... 32
Trigger key (1/5) ............................................. 36
Auto Set key
Utility key (1/9)............................................... 38
Auto Set Automatically find signal and Auto Set
Default setup Default Settings .............................................. 44 set scale
Undo Auto Set (available for 5 F5
Help Built-in Help ................................................... 45
seconds)
25 26
QUICK REFERENCE GDS-2000 Series User Manual
Display key
Auto test/Stop key
Display Select waveform display type
Auto test/Stop
See Program key (page31) DISPLAY F1
Type F 1 Vectors/ Dots Waveform accumulation On/Off
Dots
Accumulate
F 2 On/ Off F2 , F3 (display refresh when On)
CH1 ~ 4 key Off
Set display contrast
Refresh F 3
CH1 Select coupling mode F4VAR
Contrast F 4
F1 Select display grid
Coupling
F 1 / / Turn waveform invert On/Off F 5 / / F5
Invert F2
F 2 On/ Off
Off Turn bandwidth limit On/Off
BW Limit Hardcopy key
F 3 On/ Off F3
Off
Select probe attenuation factor Hardcopy See Utility key (page38)
Probe
F 4 x1/ x10/ x100
x1 F4
Help key
Cursor key
Help Turn help mode On/Off Help
27 28
QUICK REFERENCE GDS-2000 Series User Manual
29 30
QUICK REFERENCE GDS-2000 Series User Manual
PROGRAM F1
SAVE/REC SAVE/REC
Edit Select program step
F 1 Default Save To Save
Play F 1 F 1
F2VAR Setup Image Image
Step
F 2 1 ~ 20
01. Display To Display Save To Save
Select edit item F 2 F 2
Item Menu/Time/ Refs. Refs All All
F 3
Menu Setup F3 Save To Save Recall To Recall
F 3 F 3
Save edited program Setup Setup Setup Setup
Save To Save Recall To Recall
F5 F 4 F 4
Save F 5 Waveform Waveform Waveform Waveform
Recall To Recall
More F 5 F 5
Image Image
Program key (2/2)
Recall default setup F1
31 32
QUICK REFERENCE GDS-2000 Series User Manual
Save Setup Select Save Setup menu Save All Select Save All menu
Save/Recall F1 Save/Recall F1
Select destination Save
Turn ink saver On/Off
Save F 1
F 1
Setup F3 VAR All F2
Ink Saver
Save setup F 2 On/ Off Select destination
Off
Destination F4 Destination F3 VAR
F 3 Memory/USB F 3
USB Go to USB flash drive contents USB
Save all
Save F 4 edit mode Save F 4 F4
F5 (USB only)
File (USB only) File
F 5
Go to USB flash drive contents
F 5 To File Utilities
Utilities To File Utilities Utilities edit mode
F5
33 34
QUICK REFERENCE GDS-2000 Series User Manual
Recall Waveform Select Recall Waveform menu File Utilities Select file/folder or enter into
Save/Recall Save/Recall sub folder
Save/Recall F1
VAR F1
Select waveform source FILE UTILS KEYPAD
Recall Enter Create new folder or rename
F 1 F2 VAR Select F 1 F 1
Waveform Character folder/file
Source Select waveform destination New Back
F 2 USB/Memory F 2 F 2 F2,F3 (Enter new folder or rename
Folder Space
USB F3 VAR menu)
Rename F 3
Destination F 3 Recall waveform VAR F1 (Enter character)
F4 Delete F 4 Save F 4 F2 (Backspace)
Recall F 4 F4 (Save new folder)
Go to USB flash drive contents Previous
F 5
Previous
F 5
File (USB only) edit mode Menu Menu F5 (Go back to previous menu)
F 5 To File Utilities
Utilities F5 Delete folder/file
F4
Save/Recall key (8/9)
Trigger key (1/5)
Recall Image Select Recall Image menu
Save/Recall F1 Video Select Video trigger type
MENU
Select image source F1
Recall
F 1 F2VAR TRIGGER Select trigger source
Image Type
F 1
Source Show or recall image Video F2
F 2 Source (4CH) CH1/2/3/4
USB Select video standard
F3 CH1
F 2 (2CH) CH1/2
Ref Image
F 3 Recall image Standard
F 3 NTSC/SECAM/ PAL F3
On NTSC
F4 Polarity Select video polarity
Recall F 4 F 4 /
Go to USB flash drive contents F4
Line
File edit mode F 5 Field 1/ Field 2
F 5 To File Utilities 1~263 (NTSC) Select video line
Utilities F5 1~313 (SECAM/PAL)
F5 VAR
35 36
QUICK REFERENCE GDS-2000 Series User Manual
Edge/Pulse Select Edge/Pulse trigger type Slope/Coupling Select trigger slope type
MENU F1 MENU F1
TRIGGER Select trigger source TRIGGER Select trigger coupling mode
Type
F 1 F2 Slope F2
Pulse F 1 /
Source (4CH) CH1/2/3/4/Line Select trigger mode Select Frequency Rejection
F 2
(2CH) CH1/2/Ext/Line Coupling
CH1 F 2 /
F3 F3
Mode Auto/ Normal/
F 3 Rejection
Auto Single Select pulse trigger condition F 3 LF/ HF/ Off Turn Noise Rejection On/Off
When < >/ </ =/ = and pulse width Off
20.0ns
F 4
20ns~200us Noise Rej
F4
F4 VAR F 4 On/ Off
Slope / Off Go back to previous menu
F 5 To Slope/Coupling
Coupling Go to slope/coupling menu Previous F5
F 5
F5 Menu
37 38
QUICK REFERENCE GDS-2000 Series User Manual
UTILITY
F1 Hardcopy Select Hardcopy function
Hardcopy F 1 To Hardcopy menu Go to Interface menu Utility Hardcopy F1
Menu
F2 Turn Ink Saver On/Off
Interface F 2 To Interface menu H-COPY
Menu
/
Select buzzer sound Function SaveImage/ F2
F 1
F 3 / Off Save All SaveAll/ Printer
Off F3 Select printout color (only in
English/Chinese(S) Ink Saver
Language F 4 Select language F 2 On/ Off printout mode)
Chinese(T)/Spanish Off
English Korean/ etc (Printer only)
F4 Gray F3
F 5 F 3 Color Portrait/
More Portrait
Go to other menu Gray Portrait Select printout ratio (only in
Ratio printout mode)
F 4 (Printer only)
F5 50% 5 ~ 75
Previous
F4
F 5
Menu Run Hardcopy
Utility key (2/9)
Hardcopy
Utility Start Vertical calibration
F1F1 Utility key (4/9)
UTILITY
Self CAL Show system information
F 1 Vertical
Menu Interface Select interface
F2
System Utility F1
Info.
F 2 Go to Go-NoGo menu
Go-NoGo Type RS232/ USB/ GPIB Select GPIB address
F 3 To Go-NoGo menu F3 F 1
Menu RS232
(GPIB only) F2VAR
Select NoGo condition Address
NoGoWhen F 2 1 ~ 30
F 4 / Select RS-232C baud rate
1
F4 (RS232C only)
Baud Rate F2
More F 5 Go to other menu F 2 2400/ 4800/ 9600/
9600 19200/ 38400
F5 Stop Bit Select RS-232C stop bit
F 3 (RS232C only)
2 1/ 2 F3
Parity
None
F 4 (RS232C only) Select RS-232C parity
Odd/ Even/ None
Previous F4
F 5
Menu
39 40
QUICK REFERENCE GDS-2000 Series User Manual
41 42
QUICK REFERENCE GDS-2000 Series User Manual
43 44
QUICK REFERENCE GDS-2000 Series User Manual
Built-in Help
The Help key shows help contents. When a
functional key is pressed, simple explanations of
its major functionalities appear on the display.
Help
MEASUREMENT
Applicable keys Acquire Cursor Utility Program
Basic Channel activation .......................................... 47
Display Measure Save/Recall Auto test/Stop measurement Auto Set ......................................................... 48
Auto Set Help
HORI
CH1 Run/Stop ........................................................ 49
MENU
Horizontal position/scale ............................... 50
Run/Stop Hardcopy MATH
Vertical position/scale .................................... 51
MENU
Probe compensation signal............................. 52
(Trigger menu)
Automatic Measurement items ........................................ 54
measurement Individual mode ............................................. 56
Panel operation 1. Press the Help key. The Help Display All mode ............................................ 58
display changes to Help
mode. Cursor Use horizontal cursor ..................................... 59
measurement Use vertical cursor.......................................... 61
2. Press each key to access its Acquire
help contents. (example:
Math operation Addition/Subtraction/Multiplication ............... 64
Acquire key)
FFT ................................................................. 66
3. Use the Variable knob to
scroll the Help contents up Go-NoGo test Edit: Buzzer sound ......................................... 69
and down. Edit: NoGo when ............................................ 69
Edit: Source signal.......................................... 70
Edit: Continue or stop after NoGo .................. 70
4. Press the Help key again to Help
exit the Help mode. Edit: Template (boundary) .............................. 71
Run Go-NoGo test .......................................... 75
45 46
MEASUREMENT GDS-2000 Series User Manual
Activate channel To activate an input channel, Panel operation 1. Connect the input signal to Auto Set
press the Channel key. The GDS-2000 and press the
LED turns On and the input Auto Set key.
signal waveform appears on
the display. 2. The waveform appears in the center of the
display.
De-activate To disable the channel, press Before After
channel the Channel key again. If the
display menu is different from
the Channel menu, press twice
(the first press shows the
Channel menu).
47 48
MEASUREMENT GDS-2000 Series User Manual
Freeze waveform 2. In the Single Trigger mode, (Trigger) Range 1ns/Div ~ 10s/Div, 1-2-5 increment
by Single Trigger the waveform always stays The corresponding sampling rate appears on the
MENU
mode in the Stop mode, and is upper side of the display. The timebase indicator
updated only when the Mode appears on the lower side.
Run/Stop key is pressed. F 3
Single
For details, see page105.
Note: pressing the
Run/Stop key only updates Run/Stop
the waveform once it does
not switch to Run mode
(continuous update).
Stop mode In the Stop mode, the memory bar
Waveform The waveform can be moved or scaled in both Run and waveform size changes
operation and Stop mode, but in different manners. For according to the scale.
details, see page94 (Horizontal position/scale) and
page101 (Vertical position/scale).
49 50
MEASUREMENT GDS-2000 Series User Manual
The vertical scale indicator for View 1. Connect the probe between the compensation
each channel on the bottom left compensation signal output and Channel input.
of the display changes waveform
accordingly.
Stop mode In Stop mode, the vertical scale
setting can be changed but the shape
of the waveform does not change
GD S-2 1 0 4
51 52
MEASUREMENT GDS-2000 Series User Manual
Measurement items
4. Press F1 (Wave type)
repeatedly to select the Overview Voltage type Time type Delay type
wave type.
Vpp Frequency FRR
5. (For square wave only) Frequency Vmax Period FRF
To change the frequency, F 2 Vmin RiseTime FFR
1K
press F2 (Frequency) and Vamp FallTime FFF
use the Variable knob. Vhi +Width LRR
Vlo -Width LRF
Vavg Dutycycle LFR
Vrms LFF
Range 1kHz ~ 100kHz
ROVShoot
FOVShoot
6. (For square wave only) Duty Cycle
F 3 RPREShoot
To change the duty cycle, 50%
press F3 (Duty Cycle) and FPREShoot
use the Variable knob.
Voltage Vpp Difference between positive
measurement and negative peak voltage
(=Vmax Vmin)
53 54
MEASUREMENT GDS-2000 Series User Manual
55 56
MEASUREMENT GDS-2000 Series User Manual
F 1
Display All mode
F 2 Display All mode shows and updates all items from Voltage and
Time type measurement.
F 3
7. Press F5 (Previous Menu) to Previous F 5 Delay type Delay type measurement is not available in this
confirm the item selection Menu mode. Use the Individual measurement mode
and to go back to the
(page56) instead.
measurement results view.
57 58
MEASUREMENT GDS-2000 Series User Manual
59 60
MEASUREMENT GDS-2000 Series User Manual
61 62
MEASUREMENT GDS-2000 Series User Manual
63 64
MEASUREMENT GDS-2000 Series User Manual
65 66
MEASUREMENT GDS-2000 Series User Manual
67 68
MEASUREMENT GDS-2000 Series User Manual
Panel operation 1. Press the Utility key. Utility 1. Press the Utility key. Utility
2. Press F5 (More).
More F 5
3. Press F3 (Go-NoGo Menu). Go-NoGo
F 3
Menu
3. Press F4 (NoGo When)
repeatedly to select the 4. Press F3 (Violating) Violating F 3
NoGo condition. repeatedly to select whether Stop
to continue or stop test after
NoGo when waveform is
the NoGo condition is met.
outside of the boundary
NoGo when waveform is inside
the boundary
69 70
MEASUREMENT GDS-2000 Series User Manual
Stop The test stops when the NoGo Auto Creates the upper and lower boundary
condition is met. The buzzer together from an input signal, not from
does not sound. internally stored waveform.
The test stops and the buzzer Advantage: No need to store the
Stop+ waveforms prior to this selection.
sounds when the NoGo
condition is met. Disadvantage: The template shape is
Continue The test continues even when proportional to the source signal. The
the NoGo condition is met. The distance (allowance) between the source
buzzer does not sound. signal and upper/lower template are
always symmetrical.
The test continues even when
Continue+
the NoGo condition is met. The
Min/Max setting 1. Make sure the source signal, on which the
buzzer also sounds.
templates are based, appears on the display.
Note If the sound is turned Off in the buzzer setting
2. Press the Utility key. Utility
(page69), the sound is not produced even when
selecting Stop/Continue+ .
3. Press F5 (More).
More F 5
Edit: Template (boundary)
4. Press F3 (Go-NoGo Menu). Go-NoGo
F 3
Background The NoGo template sets the upper and lower Menu
amplitude boundary. Two methods are available:
Min/Max and Auto. 5. Press F1 (Template Edit). Template F 1
Min/Max Selects the upper boundary (Max) and Edit
lower boundary (Min) as separate
waveforms, from the internal memory. 6. Press F1 (Template) Template
Advantage: The template shape and the repeatedly to select the F 1
Max
distance (allowance) between the source upper (Max) or lower (Min)
signal are fully customizable. boundary template.
Disadvantage: The waveforms
(templates) have to be stored internally 7. Press F2 (Source). Use the Source
Variable knob to select the F 2
prior to this selection. RefA
template from internally
stored waveform. For
waveform store procedure,
see page129.
71 72
MEASUREMENT GDS-2000 Series User Manual
9. Repeat step 9, 10, 11 for the Template 6. Press F1 repeatedly to Auto Template
other template setting, Min F 1 F 1
Min position. Auto
or Max.
7. Press F2 repeatedly to select Source
10. When the templates are set, Save & F 2
F 4 the signal channel on which CH1
press F4 (Save & Create) to Create the template is created.
save them.
8. The template appears on the
screen as waveform A
(maximum) and waveform
B (minimum). Use the
Variable knob to set the
tolerance range. The Tolerance F 3
template in the display 0.4%
changes accordingly.
73 74
MEASUREMENT GDS-2000 Series User Manual
75 76
MEASUREMENT GDS-2000 Series User Manual
Background Program function measures input signals using Panel operation 1. Press the Program key. The Program
cursors or automatic measurement functions, in display changes into
user-defined sequence, duration, loop count, and program edit mode.
panel settings. This feature is useful for automated
and repetitive measurement, such as in assembly 2. Press F1 (Edit/Play) to Edit
line or quality inspection test. select the Edit side. F 1
Play
77 78
MEASUREMENT GDS-2000 Series User Manual
79 80
MEASUREMENT GDS-2000 Series User Manual
CONFIGURATION
Variable knob to select the
program start step: 1 ~ 20.
The S mark appears in the
selected step.
81 82
CONFIGURATION GDS-2000 Series User Manual
83 84
CONFIGURATION GDS-2000 Series User Manual
85 86
CONFIGURATION GDS-2000 Series User Manual
2. Press F5 (Mem Leng) to Mem Leng Long memory 1. One of the probe
select the memory length F 5 effect using probe compensation waveform
500
(points), short or long. comp. waveform can demonstrate long
memory mode. Connect the
Range (memory 500 Short memory length; useful for probe to the output.
point) catching high frequency signal.
2. Press the Utility key.
5000 Long memory length when three or Utility
four channels are active.
12500 Long memory length when two 3. Press F5 (More) twice.
channels are active. More F 5
87 88
CONFIGURATION GDS-2000 Series User Manual
Parameter Real-time One sampled data is used to Panel operation 1. Press the Display key. Display
sampling reconstruct a single waveform.
Short-time events might get lost if
2. Press F1 (Type) repeatedly Type
the sampling rate gets too high. F 1
to select the waveform Dots
This mode is used when the
drawing.
sampling rate is relatively low.
Equivalent- Multiple numbers of sampled data Range Dots Only the sampled dots are displayed.
time sampling are accumulated to reconstruct a
Vectors Both the sampled dots and the
single waveform. Restores greater
connecting line are displayed.
waveform details but takes longer
to update the waveform. This mode
is used when the sampling rate Example: Dots
(square wave)
becomes higher.
Example: Vectors
(square wave)
89 90
CONFIGURATION GDS-2000 Series User Manual
Contrast F 4
Accumulation Off
Panel operation 1. Press the Run/Stop key. To Run/Stop
unfreeze the waveform,
press the Run/Stop key
again.
91 92
CONFIGURATION GDS-2000 Series User Manual
Stop mode In Stop mode, the memory bar moves along with
the waveform until it reaches the end of the
2. The menu disappears. The waveform points
memory.
changes from 250 to 300.
93 94
CONFIGURATION GDS-2000 Series User Manual
Select horizontal To select the timebase (scale), Background The display update mode is
scale turn the TIME/DIV knob; left switched automatically or
(slow) or right (fast). manually according to timebase
and trigger. The indicator on the
bottom left of the display shows
Range 1ns/Div ~ 10s/Div, 1-2-5 increment
the current mode.
The corresponding sampling rate appears on the
Main mode Updates the whole displayed waveform at
upper side of the display. The timebase indicator
once. Automatically selected when the
appears on the lower side.
timebase (sampling rate) is fast.
Timebase 50ms/div (500Sa/s)
Trigger all modes
Scan mode Updates the waveform gradually from the
left side of the display to the right. The
waveform position is fixed. Automatically
selected when the timebase (sampling
Run mode In Run mode, the memory bar and waveform size
rate) is slow.
keep their proportion. When the timebase becomes
slower, it automatically switches to Scan mode (see Timebase 100ms/div (250Sa/s)
the next page). Trigger Auto mode only
95 96
CONFIGURATION GDS-2000 Series User Manual
97 98
CONFIGURATION GDS-2000 Series User Manual
99 100
CONFIGURATION GDS-2000 Series User Manual
101 102
CONFIGURATION GDS-2000 Series User Manual
103 104
CONFIGURATION GDS-2000 Series User Manual
Edge (+Delay) Triggers when the signal crosses an amplitude external trigger input
threshold in either positive or negative slope. signal
(for 2CH models only) The advanced Delay trigger
works in tandem with the edge trigger, by waiting
Trigger mode Auto GDS-2000 generates an internal trigger if
for a specified time or number of event before the
there is no trigger event, to make sure
edge trigger starts. This method allows
waveforms are constantly updated
pinpointing a location in a long series of trigger
regardless of trigger events. Select this
events.
mode especially when viewing rolling
Note: when using the delay trigger, trigger source waveform at slower timebase.
is limited to Channel 1 or 2.
Delay trigger example (by event) Normal GDS-2000 acquires waveform only when
a trigger event occurs.
A A Ext. trigger input
C
B Source (CH1 or 2) Single GDS-2000 acquires
Run/Stop
D C Delay event count (3) waveform once when a
1 2 3
B trigger event occurs, then
D First triggering point stop acquiring. Press the
Delay trigger example (by time) Run/Stop key to acquire
A A Ext. trigger input waveform again.
C B Source (CH1 or 2) Auto level When turning this function ON, GDS-2000
D C Delay time length automatically adjusts the trigger level to the center
B amplitude of the waveform.
D First triggering point
Video Extracts a sync pulse from a video format signal, Holdoff The holdoff function defines the waiting period
and triggers on a specific line or field. before GDS-2000 starts triggering again after a
trigger point. The Holdoff function ensures a
stable display.
Pulse Triggers when the pulse width of the signal is too
narrow or too wide compared to the setting.
105 106
CONFIGURATION GDS-2000 Series User Manual
107 108
CONFIGURATION GDS-2000 Series User Manual
7. Press F2 (Coupling)
repeatedly to select the
trigger coupling. Range 100ns ~ 1.3ms (by time)
Range DC, AC 2 ~ 65000 (by event)
109 110
CONFIGURATION GDS-2000 Series User Manual
Range Channel 1 ~ 4
Field 1, 2
111 112
CONFIGURATION GDS-2000 Series User Manual
Range Channel 1 ~ 4, Line, Ext 10. Press F4 (Noise Rej) to turn Noise Rej
the noise rejection On/Off. F 4
Off
4. Press F3 repeatedly to select Mode
F 3 Range On, Off
the trigger mode. Auto
113 114
CONFIGURATION GDS-2000 Series User Manual
Spanish Japanese
System Info / Language / Clock Russian German
This section describes how to set the interface, beeper, language, Dutch Polish
time/date, and probe compensation signal.
Italian French
Portuguese
View system information
Panel operation 1. Press the Utility key. Utility
Panel operation 1. Press the Utility key. Utility
2. Press F4 (Language) Language F 4
2. Press F5 (More). repeatedly to select the English
More F 5 language.
115 116
CONFIGURATION GDS-2000 Series User Manual
117 118
SAVE/RECALL GDS-2000 Series User Manual
119 120
SAVE/RECALL GDS-2000 Series User Manual
Format DSxxxx.set or Axxxx.set (proprietary format) Background For USB flash drive, file deletion, folder creation,
The setup file saves or recalls the following setting. file/folder rename are available from the front
panel. This feature is not available for internally
Acquire mode memory length stored files.
Contents
Cursor source channel cursor on/off
cursor location
Panel operation 1. Connect the drive to the Front Rear
front or rear panel USB port.
Display dots/vectors accumulation Note: Only one host
grid type on/off connection, front or rear, is
allowed at a time.
Measure item source channel
Utility hardcopy type ink saver on/off 2. Press the Save/Recall key. Save/Recall
interface type RS-232 config Select any save or recall
functionality, for example (Example)
buzzer type GPIB address
USB destination in Save
Save
Go-NoGo cond. menu language image function. F 1
Image
Program step contents loop count
Destination
start/stop steps F 3
USB
Horizontal display mode scale
position 3. Press F5 (File Utilities). The File
display shows the USB flash F 5
Trigger trigger type source channel Utilities
drive contents, root
trigger mode video standard
directory.
video polarity video line
pulse timing slope/coupling
Channel vertical scale vertical position
(vertical) coupling mode invert on/off
bandwidth limit probe
on/off attenuation
Math operation type source channel
vertical position unit/div
FFT window
121 122
SAVE/RECALL GDS-2000 Series User Manual
123 124
SAVE/RECALL GDS-2000 Series User Manual
Quick Save (HardCopy) Panel operation 1. Connect the drive to the Front Rear
front or rear panel USB port.
Background The Hardcopy key works as a Note: Only one host
Hardcopy connection, front or rear, is
shortcut for saving or printing
out information. allowed at a time.
Once set, subsequent file saving only requires 2. Press the Utility key. Utility
pressing the Hardcopy key. Hardcopy key can be
configured into three operations: save image, save
all (image, waveform, setup), and printing. 3. Press F1 (Hardcopy Menu). Hardcopy
F 1
The printing operation is described in page145. Menu
Using the Save/Recall key can Save/Recall
also save files but with more 4. Press F1 (Function) Function
repeatedly to select Save F 1
configurations. For details, see Save All
page127. image or Save all.
Function
F 1
SaveImage
Functionality Save image Saves the current display image into
(*.bmp) a USB flash drive connected to the
front or rear panel terminal. 5. To invert the color for the Ink Saver
saved or printed display F 2
Save all Saves the following items into a USB On
image, press F2 (Ink Saver)
flash drive connected to the front or
and turn On the Ink Saver.
rear panel terminal.
Ink Saver On (normal) Ink Saver Off (inverted)
Current display image (*.bmp)
Current system setup (*.set)
Current waveform data (*.csv)
Last stored system setup (*.set)
Last stored waveform data (*.csv)
Print out Prints out the display image to an
external printer connected to USB
port. For details, see page145. 6. To save the image or folder, Hardcopy
press the Hardcopy key.
The file or folder is saved to
the root directory of the USB
flash drive.
125 126
SAVE/RECALL GDS-2000 Series User Manual
127 128
SAVE/RECALL GDS-2000 Series User Manual
129 130
SAVE/RECALL GDS-2000 Series User Manual
131 132
SAVE/RECALL GDS-2000 Series User Manual
Save All
133 134
SAVE/RECALL GDS-2000 Series User Manual
File type/source/destination
6. Press F3 (Destination). Use Destination Default panel Factory installed Current front panel
the Variable knob to select F 3
USB setup setting
the file name.
Reference Internal memory: A ~D Current front panel
waveform
8. Together with the current setup/waveform/ Panel operation 1. Press the Save/Recall key. Save/Recall
image, the last saved waveform file (one from
W1 ~ W20) and setup file (one from S1 ~ S20)
are also included in the folder. 2. Press F1 (Default Setup). Default
The factory installed setting F 1
Setup
USB file utility To edit USB flash drive File is recalled and replaces the
contents (create/ delete/ F 5 current panel setting.
Utilities
rename files and folders), press
F5. For details, see page122. Setting contents The following is the default setting contents.
135 136
SAVE/RECALL GDS-2000 Series User Manual
137 138
SAVE/RECALL GDS-2000 Series User Manual
139 140
SAVE/RECALL GDS-2000 Series User Manual
141 142
SAVE/RECALL GDS-2000 Series User Manual
Recall image
6. To show the image on the Ref Image
display, press F3 (Ref F 3
On
Panel operation 1. Connect the USB drive to Front Rear Image) ON or F4 (Recall).
the front or rear panel USB Recall F 4
port.
Note: Only one host
connection, front or rear, is 7. The image appears on the
allowed at a time. display and the R
indicator appears at the top
2. Press the Save/Recall key. left corner of the display.
Save/Recall
3. Press F5 (More).
More F 5
143 144
PRINT OUT GDS-2000 Series User Manual
2 Configure interface
PRINT OUT
Panel operation 1. Press the Utility key. Utility
1. Connect the printer to the USB host port, front 2. Press F1 (Hardcopy Menu). Hardcopy
F 1
or rear panel. Menu
Front panel Rear panel
3. Press F1 (Function) Function
repeatedly to select Printer F 1
Printer
if it is not selected yet.
USB Note Using the front and rear USB host port at the same
time is forbidden (Example: printer to the rear
panel, storage device to the front panel).
145 146
PRINT OUT GDS-2000 Series User Manual
REMOTE CONTROL
image, press F2 (Ink Saver)
and turn On the Ink Saver.
Ink Saver On (normal) Ink Saver Off (inverted)
CONFIG
This chapter describes basic configuration of
IEEE488.2 based remote control. For command list,
refer to the programming manual downloadable
from GWInstek website, www.gwinstek.com.tw.
5. To select black/white or Gray
color printing, press F3 F 3
Portrait Configuration Configure USB interface.................................149
(Portrait) repeatedly; Gray
(b&w) or Color. Configure RS-232C interface ..........................150
Configure GPIB interface (optional) ...............152
6. To select the printed size, Ratio USB/RS-232C remote control software...........154
press F4 (Ratio). Use the F 4
50%
Parameter knob to change
the ratio with respect to the
real display size.
4 Printout
147 148
REMOTE CONTROL CONFIG GDS-2000 Series User Manual
149 150
REMOTE CONTROL CONFIG GDS-2000 Series User Manual
Pin assignment 12345 2: RxD (Receive data) 1. Turn Off the GDS-2000 power
switch.
3: TxD (Transmit data)
5: GND 2. Take off two screws and remove the rear panel
6789
4, 6 ~ 9: No connection GPIB module cover.
Pin2 RxD TxD Pin2 3. Insert the GPIB module and put the screws
Pin3 TxD RxD Pin3 back.
151 152
REMOTE CONTROL CONFIG GDS-2000 Series User Manual
5. Press F2 (Address). Use the Address Terminal Invoke the terminal application such as MTTTY
Variable knob to change the F 2
1 application (Multi-Threaded TTY). For RS-232C, set the COM
GPIB address. (USB/RS-232C) port, baud rate, stop bit, data bit, and parity
Range 1 ~ 30 accordingly.
To check the COM port No, see the Device
6. Connect the GPIB cable to Manager in the PC. For WinXP, Control panel
the rear panel port: 24-pin System Hardware tab.
female connector.
Functionality Run this query command via the terminal.
GPIB constraints Maximum 15 devices altogether, 20m cable check *idn?
length, 2m between each device
This should return the Manufacturer, Model
Unique address assigned to each device number, Serial number, and Firmware version in
At least 2/3 of the devices turned On the following format.
No loop or parallel connection GW, GDS-2064, 000000001, V1.00
153 154
BATTERY OPERATION GDS-2000 Series User Manual
BATTERY OPERATION
4. Turn On the power and
make sure the battery icon
appears at the top left
corner of the display.
The optional battery allows portable operations
Rating Type Li-Ion battery x 2, 11.1V average
such as field applications. Battery packs and
related internal components are factory installed Running time 3 hours typical
items: contact the service center for new Charging time 8 hours typical when Power Off
installation.
16 hours typical when Power On
Never insert or remove the battery while the Battery status 1. To view the battery
Warning Utility
power is On. installation and recharge
status, press the Utility key.
Battery insertion 1. Turn Off the power and take off the power
cord. 2. Press F5 (More).
More F 5
RS232
155 156
MAINTENANCE GDS-2000 Series User Manual
MAINTENANCE
automatically, in less than 5
minutes.
2. Press F5 (More).
More F 5 Probe Compensation
the display. X1
X10
7. Press F5. F 5
2. Press the Utility key. Utility
(no menu item)
157 158
MAINTENANCE GDS-2000 Series User Manual
4. Press F1 (ProbeComp
Menu).
x2
ProbeComp
Menu
F 1
FAQ
I pressed the Power (On/Standby) key on the front panel but nothing
5. Press F1 (Wavetype) happens.
repeatedly to select the I connected the signal but it does not appear on the display.
standard square wave.
I want to remove the (Measurement result / FFT result / Help
6. Press the Auto Set key. The contents) from the display.
Auto Set
compensation signal The waveform does not update (frozen).
appears on the display. The probe waveform is distorted.
7. Press the Display key, then Auto Set does not catch the signal well.
Display
F1 (Type) twice to select the I want to clean up the cluttered panel settings.
vector waveform. The display image printout is too dark on the background.
Type F 1
Vectors I want to install the optional battery pack.
I put the battery pack in but it is not working.
The date and time setting are not correct.
USB does not work.
8. Turn the adjustment point on the probe until
the signal edge becomes sharp. The accuracy does not match the specification.
Make sure you turned On the rear panel Power switch. For power
up sequence, see page22.
Make sure you have activated the channel by pressing the Channel
key (the LED turns On).
159 160
FAQ GDS-2000 Series User Manual
I want to remove the (Measurement result / FFT result / The display image printout is too dark on the background.
Help contents) from the display.
Use the Inksaver function which reverses the background color. For
To clear automatic measurement result, press the Measure key twice, details, see page145.
then Press F4 (OFF). See page54 for details.
To clear FFT result, press the Math key twice. See page63 for details. I want to install the optional battery pack.
To clear Help result, press the Help key again. See page45 for details. I put the battery pack in but it is not working.
You might need to compensate the probe. For details, see page158. USB does not work.
Note that the frequency accuracy and duty factor are not specified
for probe compensation waveform and therefore it should not be Make sure you are not using the front and the rear USB host
used for other reference purpose. connector at the same time. Disconnect either of the USB device and
try again.
161 162
APPENDIX GDS-2000 Series User Manual
APPENDIX
For GPIB interface and remote control details, see page148.
163 164
APPENDIX GDS-2000 Series User Manual
165 166
APPENDIX GDS-2000 Series User Manual
167 168
APPENDIX GDS-2000 Series User Manual
Declaration of Conformity
INDEX
We
GOOD WILL INSTRUMENT CO., LTD.
(1) No.7-1, Jhongsing Rd., Tucheng City, Taipei County, Taiwan
(2) No. 69, Lu San Road, Suzhou City (Xin Qu), Jiangsu Sheng, China
declare, that the below mentioned product
2-4 channel difference ............... 10 coupling mode ......................... 102
Type of Product: Power Supply AC coupling ............................. 102 menu tree ....................................... 27
Model Number: GDS-2062, GDS-2064, GDS-2102, GDS-2104, acquisition .................................. 84 cursor........................................... 59
GDS-2202, GDS-2204 menu tree ....................................... 26 menu tree ....................................... 27
are herewith confirmed to comply with the requirements set out in the addition....................................... 64 shortcut .......................................... 27
Council Directive on the Approximation of the Law of Member States menu tree ....................................... 29 specification................................. 166
relating to Electromagnetic Compatibility (89/336/EEC, 92/31/EEC, auto level .................................. 108 cycle time measure .................... 55
93/68/EEC) and Low Voltage Directive (73/23/EEC, 93/68/EEC). auto set........................................ 48 date setting ............................... 116
effect on channel ........................... 47 faq.................................................. 162
For the evaluation regarding the Electromagnetic Compatibility and
exception ........................................ 48 indicator ......................................... 20
Low Voltage Directive, the following standards were applied: menu tree ....................................... 43
faq.................................................. 161
EMC specification................................. 167 DC coupling ............................. 102
EN 61326-1: Electrical equipment for measurement, control and laboratory auto template ............................. 74 declaration of conformity ....... 169
use EMC requirements (1997 + A1:1998 + A2:2001 + A3:2003) auto trigger............................... 106 default setup............................. 136
Conducted Emission Electrical Fast Transients automatic measurement ........... 56 contents .......................................... 44
Radiated Emission EN 61000-4-4: 2004 faq.................................................. 161 effect on channel ........................... 47
menu tree ....................................... 30 menu tree ....................................... 32
EN 55011: Class A 1998 + A1:1999
overview ........................................ 54 delay measure ............................ 55
+ A2:2002 shortcut .......................................... 30 delay trigger ............................. 110
Current Harmonics Surge Immunity specification................................. 166 menu tree ....................................... 37
EN 61000-3-2: 2000 + A2:2005 EN 61000-4-5: 1995 + A1:2001 average acquisition.................... 84 display......................................... 92
Voltage Fluctuations Conducted Susceptibility average voltage measure .......... 55 contrast setting.............................. 92
EN 61000-3-3: 1995 + A1:2001 EN 61000-4-6: 1996 + A1:2001 bandwidth limitation .............. 103 diagram .......................................... 19
battery ....................................... 155 grid setting..................................... 93
+A2:2005
faq.................................................. 162 menu tree ....................................... 28
Electrostatic Discharge Power Frequency Magnetic Field save image ................................... 131
icon on power up.......................... 22
EN 61000-4-2: 1995 + A1:1998 + EN 61000-4-8: 1993 + A1:2001 shortcut .......................................... 28
specification................................. 167
A2:2001 blackman window..................... 64
specification................................. 167
Radiated Immunity Voltage Dip/ Interruption dot waveform ............................. 90
buzzer ......................................... 69
EN 61000-4-3: 2002 + A1:2002 EN 61000-4-11: 2004 menu tree ....................................... 39 download information .............. 12
calibration, vertical resolution 157 duty cycle measure.................... 55
Safety
caution symbol............................. 5 ECL ............................................ 107
Low Voltage Equipment Directive 73/23/EEC & amended by 93/68/EEC edge trigger............................... 109
Safety Requirements channel........................................ 47
faq.................................................. 160 menu tree ....................................... 37
IEC/EN 61010-1: 2001 menu tree ....................................... 27 EN61010 .................................... 169
shortcut .......................................... 27 measurement category .................. 6
status indicator.............................. 20 pollution degree.............................. 7
cleaning the instrument .............. 7 environment ............................. 167
169 170
INDEX GDS-2000 Series User Manual
safety instruction ............................ 7 scale................................................. 95 compensation menu tree ............. 42 serial number............................ 115
equivalent time sampling ......... 89 shortcut .......................................... 28 compensation signal overview... 52 service operation
external trigger......................... 106 specification................................. 166 faq.................................................. 161 about disassembly .......................... 6
input terminal ............................... 16 IEC 1010-1 .................................168 memory length demonstration .. 88 contact .......................................... 162
specification................................. 166 initialization................................23 package list .................................... 12 setup
falling time measure.................. 55 ink saver peak detect demonstration.......... 85 default contents ............................ 44
in display save ............................ 132 specification................................. 168 file format .................................... 121
FFT ............................................... 66
horizontal cursor .......................... 60 in hardcopy.................................. 126 program ...................................... 77 how to recall ................................ 139
menu tree ....................................... 29 in save all ..................................... 134 how to edit..................................... 78 how to save.................................. 128
overview ........................................ 63 input frequency indicator .........20 how to run ..................................... 80 menu tree ....................................... 33
vertical cursor................................ 62 menu tree ....................................... 31 recall menu tree ...................... 34, 35
interface.....................................149
shortcut .......................................... 31 short memory ............................. 87
file format ................................. 119 menu tree ....................................... 40
specification................................. 167 program manual download ..... 12 single trigger mode.................. 106
firmware version...................... 115
invert waveform.......................103 pulse time measure ................... 55 faq.................................................. 161
flattop window........................... 64
language selection....................115 pulse width trigger.................. 113 with run/stop ............................... 49
FM example ................................ 87
menu tree ....................................... 37 spike noise example................... 87
frequency measure .................... 55 list of features .............................11
real time sampling..................... 89 stop icon...................................... 49
front panel diagram................... 13 long memory ..............................87
rear panel diagram .................... 17 subtraction .................................. 64
fuse replacement ...................... 163 low voltage measure..................54
recall .......................................... 136 menu tree ....................................... 29
safety instruction ............................ 7 math .............................................63
default setup................................ 136 system information.................. 115
generic purpose signal .............. 52 faq.................................................. 161
menu tree ....................................... 32 battery........................................... 156
go-nogo ....................................... 68 menu tree ....................................... 29
reference waveform ................... 138 template for go-nogo ................. 71
how to configure........................... 69 shortcut .......................................... 29
setup ............................................. 139
how to run ..................................... 75 memory length ...........................86 tilt stand ...................................... 21
shortcut .......................................... 32
menu tree ....................................... 41 menu on/off ...............................93 waveform..................................... 141 time setting ............................... 116
output specification.................... 167 min/max template.....................72 faq.................................................. 162
rectangular window.................. 64
output terminal ............................. 76 model difference ........................10 indicator ......................................... 20
reference waveform menu tree ....................................... 43
template menu tree ...................... 41 normal acquisition .....................84 how to recall ................................ 138
GPIB........................................... 152 trigger........................................ 105
normal trigger...........................106 menu tree ....................................... 32
module installation .................... 164 delay ............................................. 110
NTSC .........................................107 remote control.......................... 148 edge............................................... 109
ground interface configuration............... 149
overshoot voltage measure .......55 menu tree ....................................... 36
coupling ....................................... 102
package contents ........................12 rising time measure................... 55 parameter..................................... 106
symbol .............................................. 5
terminal .......................................... 16 PAL ............................................107 roll mode .................................... 97 pulse width.................................. 113
hanning window........................ 63 pc software download ...............12 RS-232C interface..................... 150 shortcut .......................................... 36
peak detect acquisition..............84 run/stop ..................................... 49 single trigger with run/stop....... 49
hardcopy ................................... 125
peak voltage measure................54 faq.................................................. 161 specification................................. 166
menu tree ....................................... 40
horizontal position ....................... 94 status indicator.............................. 20
shortcut .......................................... 40 power on/off ..............................22
horizontal scale ............................. 95 video ............................................. 112
help .............................................. 45 faq.................................................. 160
safety instruction ............................ 6 save............................................ 127 TTL ............................................ 107
faq.................................................. 161
switch overview............................ 17 display image .............................. 131 UK power cord............................. 8
high voltage measure ................ 54
preshoot voltage measure .........55 menu tree ....................................... 32 USB
holdoff ....................................... 108 save all.......................................... 133
printout driver download........................... 12
horizontal.................................... 94 setup ............................................. 128 faq.................................................. 162
basic operation .............................. 50 faq.................................................. 162
shortcut .......................................... 32 file menu tree ................................ 36
cursor menu tree........................... 27 menu tree ....................................... 40
specification................................. 167 file operation ............................... 122
cursor operation............................ 59 probe..........................................158 waveform..................................... 129 PC software download .............. 154
menu tree ....................................... 28 attenuation level ......................... 104
scan mode................................... 96 remote control interface ............ 149
position........................................... 94 attenuation menu tree.................. 27
SECAM ..................................... 107 utility
171 172
INDEX
173