Академический Документы
Профессиональный Документы
Культура Документы
LuxelServer.
The LuxelServer is a windows service that provides, among other services, database, licensing, user interface, and message
logging facilities, for firewire connected Luxel Imagesetters. It is an integral part of the system that must be running before
the engine can be used for imaging.
Contents
1. System requirements
2. License agreement
4. Installation notes
5. User guide
6. Release notes
Item Requirement
Operating system Windows XP SP1, Windows 2000 SP4, Windows Server 2003 SP1
Luxel CTP V6 1.11 or V6e 1.0
1. Copyright in and title to the software is and remains vested in FUJIFILM, or third party owner.
2. Licensee is hereby granted a non-exclusive licence to install and use the software (on a single computer) (at a single
location)
3. Licensee may not copy the software save to make one copy solely for back-up purposes. Any back-up copy of the
software must contain the same copyright notice as appears on or in the software.
4. Licensee may not modify, adapt, translate, reverse engineer, decompile, disassemble or otherwise attempt to
discover the source code of the software.
5. Licensee may not rent, lease or sub-licence, lend or assign the software or any documentation supplied therewith,
nor translate this license without the written consent of FUJIFILM which consent shall not be withheld unreasonably.
6. FUJIFILM warrants that the software will perform substantially in accordance with the specification therefore in the
written documentation accompanying the software. In the event of a breach of warranty FUJIFILM will at its option
and cost either correct errors in the software or refund to the licensee the price paid. Licensee accepts that this shall
be its sole remedy in the event of such a breach.
7. LICENSEE ACCEPTS THAT IN NO EVENT SHALL FUJIFILM BE LIABLE TO LICENSEE FOR ANY CONSEQUENTIAL LOSS
OR DAMAGE INCLUDING ANY LOSS OF PROFIT ARISING OUT OF LICENSEES' USE OF THE SOFTWARE AND/OR THIS
AGREEMENT.
8. Licensee agrees and certifies that none of the software will be shipped, transferred and re-exported, directly or
indirectly, into any country prohibited by the United States Export Administration Act and regulations thereunder or
will be used for any purpose prohibited by the same.
9. This agreement shall be subject to and construed in accordance with the laws of England.
1. This product includes software developed by The Apache Software Foundation (http://www.apache.org/). A copy of
the license is available in the file LICENSE.log4j
Licensee will indemnify Fujifilm against any loss suffered by Fujifilm as a result of a breach of third party terms by user.
4.1 Special note if upgrading from Luxel V6/V6e PCI or from LuxelServer 1.x to LuxelServer 2.x
The database will be imported to a new location. User settings and licence keys will be preserved. However any log files that
have been created will be listed in the new application but not be able to be deleted or exported. Please export log files that
need to be kept and then delete the log entry using the PCI user interface before performing the upgrade.
Windows 2000. requires that the firewire driver is manually installed following the installation of the LuxelServer application.
Please refer to the Windows 2000 specific. instructions in section 4.5.
Connect, and switch on, the Luxel imagesetter if it is not already connected and ensure that either the application or boot
system is running. Note: it is also acceptable for the imagesetter to be in the shutdown state.
Launch the LuxelServer installer. The LuxelServer is distributed on an CD that will auto-run. Alternatively, the LuxelServer
may be downloaded, as a self extracting executable, from the internet.
Follow the instructions that are provided by the installer. When this completes, check that the installation has completed
successfully. Please note that the application must be installed in the default 'Program Files' folder.
If the required imagesetter is connected and running as required then the connection status should be displayed as 'Online':
2. Check that the imagesetter has booted without problems. It can be running the boot system or application.
3. Check that the correct firewire driver has been installed and is running without problem. See below:
If the driver needs to be upgraded then select update driver from the context menu when the Fujifilm Luxel V-6 CTP Device
is selected. Then follow these instructions:
Do not use the web to search for a driver. Select 'No, not this time'
Select, 'Install software automatically'.
Browse to the file LuxelV6.sys which is located in LuxelV6, relative to the install folder. Click 'Ok' to complete the
installation. You can check that the driver is installed correctly by using the windows device manager. When the Luxel
Imagesetter is powered on and initialised, the device manager will indicate that the LuxelV6 device driver is loaded:
4.5 Windows 2000.
For windows 2000, start with the Luxel Imagesetter disconnected or switched off. Install the LuxelServer application as
described above. Once this is done, reconnect or switch on, the Luxel Imagesetter. If you are upgrading from a V-6 PCI
version to Luxel Server 2.1, or you are installing the Luxel Server for the first time then you will need to upgrade or install
the firewire driver. Either, use the 'New Hardware Wizard' or the device manager (see section 4.4) to do this.
If this window is displayed then browse to the location of LuxelV6.sys which is located in LuxelV6, relative to the install
folder. Press 'Ok' then 'Next' to complete the installation of the firewire driver.
Check that the driver is installed correctly as described in the general section of these notes, section 4.3 and section 4.4
Contents
1. Installed Applications
2. Service Manager
3. LuxelServerManager
5. Problems, troubleshooting
Installed Applications
The LuxelServer is installed as a windows service. There are also a few support applications that are installed too. These are
installed in the LuxelServer program group that is accessed from the start menu:
'dbfutils'
The LuxelServer has an associated database that is used to store any persistent data that is needed by the Luxel system.
The 'dbfutils' application can be used to view this data and to make backups.
Diagnostic Terminal
This will start a HyperTerminal session. This can be used to issue diagnostic commands and view diagnostic data from a
Luxel imagesetter, that is connected to the host PC with an RS232 cable.
LuxelServerManager
This application is started automatically at start-up and has an associated icon in the system tray. It provides a convenient
way of controlling the LuxelServer and checking its status.
Documentation
This is a shortcut to this documentation.
Service Manager
The LuxelServer can be controlled from the service manager. The following instructions show how to do this assuming
Windows XP, but similar principles exist for other Windows operating systems.
Right-click on 'My Computer' from the desktop or start menu and select 'Manage'
This will then launch the Computer Management window. Select 'Services' from the 'Services and Applications' node in the
left-hand view.
The LuxelServer service will be listed along with its current state in the right-hand view. Double-click the LuxelServer item
to launch a dialog that can be used to stop and start the service.
If you want to disable the service so that it doesn't start automatically when the PC is switched on, set the 'Startup type' to
'Manual' in the LuxelServer properties dialog.
LuxelServer Manager
The recommended way of controlling the LuxelServer service and to check its status is to use the LuxelServerManager.
The LuxelServerManager is started automatically when the user logs in. An icon appears in the system task tray to show
that the manager has started.
Press 'Stop' to stop the LuxelServer, for example if you want to swap the connected engine with another, or if you want to
change to a different database. Press 'Start' to start the LuxelServer again.
Save.
2. Copy the database using the 'dbfutil' application that is distributed with the LuxelServer
Restore.
1. Ensure that the LuxelServer is stopped. If not, stop the LuxelServer, using the LuxelServer Manager
2. Use the 'dbfutil' application that is distributed with the LuxelServer to import a saved databse. Press the 'Restore'
button and specify the previously saved idx database file.
Troubleshooting
If the connection state of the LuxelServer, indicated by the LuxelServer Manager control panel, is inconsistent with what
you expect, for example the state remains as 'Device not attached', then the following information may help:
Unplug the firewire cable and replace it. If this fails, then try to restart the LuxelServer service using the following
procedure:
LuxelServer 2.0.
Version 2.0 is required to support the Luxel Dashboard 1.0 application.
LuxelServer 2.1.
LuxelServer 2.1.
Version 2.1 improves the resilience of this application to firewire bus reset
events. Specifically, if VNIpc fails to register with the engine then the application
assumes that the engine is disconnected. Previously the registration message
would be re-sent but always fail. This resulted in the application consuming 99%
of the CPU usage, effectively causing the PC to 'lock-up'. The engine monitor
functionality has also been improved, allowing the server to recover after a
VNIpc registration failure.