Академический Документы
Профессиональный Документы
Культура Документы
1
Material data sheet, edition April 2016
DILLIMAX 690 is a high strength quenched and tempered, fine grained structural steel with a minimum yield
strength of 690 MPa (100 ksi)2 in its delivery condition (referring to the lowest thickness range).
DILLIMAX 690 is preferentially used for welded steel structures within mechanical constructions, plant
constructions and structural steel works, such as machines for structural engineering, conveying plants, hoists,
cranes, flood gates, bridges and frameworks.
Product description
1
The current version of this material data sheet can be also found on http://www.dillinger.de.
2
The approximately converted values in brackets are for information only.
Delivery condition
Water quenched and tempered according to EN 10025-6.
Mechanical properties
65 (2.5) < t 100 (4) 770 930 (112 136) 670 (97)
100 (4) < t 150 (6) 720 900 (104 130) 630 (91) 14 15
150 (6) < t 200 (8) 700 880 (102 128) 610 (88)
200 (8) < t 255 (10) 690 870 (100 126) 600 (87)
a
The approximately converted values in brackets are for information only.
b
Higher minimum values may be agreed on request. For Offshore applications special grades are available.
c
If not apparent, the yield strength Rp0.2 is measured instead.
d
These values apply if tested according to ASTM A370.
Testing
Tensile and impact tests will be performed according to EN 10025-6 once per heat and 40 t.
Tests on every heat treatment unit may be possible on request. The test pieces are taken and prepared according
to part 1 and 6 of EN 10025.
The tensile test is carried out on specimens of gauge length L o = 5.65So respectively Lo = 5do, in accordance
with EN ISO 6892- 1. Tensile tests according to ASTM A370 may be agreed. The impact test will be carried
out on transverse Charpy-V-specimens in accordance with EN ISO 148-1 using a 2 mm striker.
Unless otherwise agreed, the test results are documented in an inspection certificate 3.1 in accordance with
EN 10204.
Identification of plates
Unless otherwise agreed, the marking is carried out via steel stamps with at least the following information:
steel grade (e.g. DILLIMAX 690 B, T or E)
heat number
number of mother plate and individual plate
the manufacturers symbol
inspection representatives sign
Processing
The entire processing and application techniques are of fundamental importance to the reliability of products
made from this steel. The user should ensure that his design, construction and processing methods are aligned
with the material, correspond to the state-of-the-art that the fabricator has to comply with and are suitable for
the intended use. The customer is responsible for the selection of the material. The recommendations of the
EN 1011 (welding) and CEN/TR 10347 (forming) as well as recommendations regarding job safety in
accordance with national rules should be observed.
Hot forming
If the temperature of 560 C (1 040 F) is exceeded, the initial tempering can be altered so that the mechanical
properties are affected. To regain the initial properties new quenching and tempering become necessary.
However, water quenching of a formed workpiece or component will often be less effective than the original
quenching in the plate mill so that the fabricator may not be able to reestablish the properties required and
therefore hot forming may not be suitable. In this respect we recommend you to contact the steel producer prior
to ordering, in all cases where hot forming is required.
Finally, it is the fabricators responsibility to obtain the required values of the steel through an appropriate heat
treatment.
Heat treatment
A stress relief heat treatment can be performed at a maximum temperature of 560 C (1 040 F) and maximum
holding time of 60 minutes without significant impairment of the properties. After a stress relief heat treatment
using the specified parameters, the requirements for mechanical and technological properties are met. It has to
be specified prior to ordering if higher stress relieving temperatures or longer holding times have to be applied.
The verification of appropriate stress relieving parameters for a delivered plate may be possible on request.
Detailed instructions for flame cutting, welding, machining and about the structural properties of the
DILLIMAX are provided in the technical information MAKE SAVINGS WITH HIGH STRENGTH STEELS
DILLIMAX.
Tolerances
Unless otherwise agreed, the tolerances will be in accordance with EN 10029, with class A for thickness and
table 4, steel group H, for the maximum flatness deviation. Smaller flatness deviations may be possible on
request prior to order.
Surface quality
Unless otherwise agreed, the specifications will be in accordance with EN 10163-2, class A2.
Ultrasonic testing
If not agreed otherwise, DILLIMAX 690 fulfils the requirements of class S1E1 in accordance with EN 10160.
Contact
For your local representative AG der Dillinger Httenwerke
please contact our coordination office in Dillingen: P.O. Box 1580
66748 Dillingen/Saar, Germany
Telephone: +49 6831 47 2223
Telefax: +49 6831 47 3350
e-mail: info@dillinger.biz
http://www.dillinger.de
or visit our website: