Академический Документы
Профессиональный Документы
Культура Документы
Edition 09/12/2015
Identification Number
02 08 14 02 002 0 000025
Sikafloor -21N PurCem (IN)
Uses Sikafloor -21N PurCem (IN) floors are primarily used to protect concrete
substrates, but are equally effective over most steel surfaces that have been
properly prepared and supported.
Typically used in food processing plants, wet & dry process areas, freezers &
coolers, dairies, breweries, wineries, distilleries, laboratories, chemical process
plants, pulp and paper plants, warehouses and storage areas.
Characteristics / Resists a very wide range of organic and inorganic acids, alkalis, amines, salts
Advantages and solvents. Consult Sika Technical Sales for full details. Refer to the Sikafloor
PurCem Chemical Resistance Chart.
Similar coefficient of thermal expansion to concrete allowing movement with the
substrate through normal thermal cycling. It will perform and retain its physical
characteristics through a wide temperature range from -40C up to 120C.
Bond strength in excess of the tensile strength of concrete, concrete will fail first.
Non-taint, odourless.
Behaves plastically under impact / deforms but will not crack or debond.
High abrasion qualities result from its pure silica aggregate structure.
Extra Expansion joints are not necessary; simply maintain and extend existing
expansion joints up through the Sikafloor PurCem (IN) Flooring System.
Easily maintained.
USDA acceptance for use in food plants in the U.S.A.
Canadian Food Inspection Agency acceptance for use in food plants in Canada.
British Standard Specifications (BSS) acceptance for use in the U.K.
HACCP Certifications Sikafloor 21 Purcem (IN) is certified as suitable for use in food and beverage
facilities that operate in accordance with a HACCP based food safety program.
Certificate Number I PE 769 SA - R2- 01b
Technical Data
Packaging 18.5 kg x 2set
Comp.A: 3 kg/pail, Comp.B: 3.0 kg/pail, Comp.C: 11.5 kg/bag, Comp.D: 1.0
kg/pack
1
Shelf Life Components A and B: 1 year in original unopened packaging.
Components C and D: 6 months in original unopened packaging.
Store dry between 10 C - 25 C. Protect from freezing.
Mix Ratio Components A:B:C:D = Mix full units only.
24 hours > 22
7 days > 40
28 days > 45
Tensile Strength 6.5 MPa after 7 days cure at 27C ( EN ISO 527-2)
Flexural Strength 14.7 MPa after 28 days cure at 27C ( EN ISO EN 196)
Bond Strength > 2.5 MPa (failure from concrete) (EN 1542)
Thermal Compatibility Pass ( ASTM C 884)
Hardness, Shore D 80-85 (ASTM D 2240)
Indentation ~ 0% (MIL-PRF-24613)
Impact Resistance > 20 joules at 3 mm of thickness IS 101 Part 5:1999
Abrasion Resistance 861 mg ASTM D 4060
H-22/1000 cycles/1000 g
Coefficient of Friction Steel 0.3 ASTM D 1894-61T
Rubber 0.5
-5
Coefficient of Thermal 1.6 x 10 mm/mm/C ASTM D 696
Expansion
Water Absorption 0.10% ASTM C 413
Chemical Resistance Consult Sika Technical Sales
2
Application
Instructions
Surface Preparation Concrete surfaces must be clean and sound. Remove all dust, dirt, existing paint
films, efflorescence, exudates, laitance, form oils, hydraulic or fuel oils, brake fluid,
grease, fungus, mildew, biological residues or any other contaminants which may
prohibit good bond. Prepare the surface by appropriate mechanical means,
approved by Sika to achieve (CSP 3-6). The compressive strength of the concrete
substrate should be at least 25 MPa at 28 days and a minimum of 1.5 MPa in
tension at the time of application. Repairs to cementitious substrates, filling of
blowholes, leveling of irregularities, etc. should be carried out using an appropriate
Sika profiling mortar.
Contact Sika Technical Sales for a recommendation.
Edge Terminations - All free edges of a Sikafloor PurCem (IN), whether at the
perimeter, along gutters or at drains require extra anchorage to distribute
mechanical and thermal stresses. This is best achieved by forming or cutting
grooves in the concrete. Grooves should have a depth and width of 2 times
thickness of the Sikafloor PurCem (IN) mortar. Refer to the edge details provided.
If necessary, protect all free edges with mechanically attached metal strips.
Never featheredge, always turn into an anchor groove.
Expansion Joints - Should be provided in the substrates at the intersection of
dissimilar materials. Isolate areas subject to thermal stresses, vibration movements
or around load-bearing columns and at vessel sealing rings. Refer to details.
Mixing Mixing will be affected by temperature.
Condition materials for use from 18C to 25C.
Stir Component A first for approx. 15 seconds.
Add component B, and mix for approx. 30 seconds with low speed mixer.
While mixing, add simultaneously but slowly (DONT DUMP!) component C
(powder) and Component D (pigment pack) within 15 seconds.
Further mix for 2 minutes until the mixture is homogeneous and the pigment is
uniformly dispersed.
Mix full unit only
Note: Improve flowability on cool substrates can be achieved by removing a
maximum of 1 kg of Component C (powder) per unit.
Application Sikafloor -21N PurCem (IN)
Scratch Coat - Priming of concrete substrates is not usually required under typical
circumstances. However, due to variations in concrete quality, surface conditions,
surface preparation and ambient conditions, reference test areas are recommended
to determine whether priming is required to prevent the possibility of blisters,
debonding, pinholes and other aesthetic variations. Mix and apply a scratch coat of
Sikafloor -21N PurCem (IN) using steel trowels to spread the materials to
approximately 1.0 mm thickness, This application must seal the concrete surface,
fill in surface irregularities including pock marks, non-moving control joints and
cracks. Allow overnight cure (16 hours) at 20C before application of the body coat.
Body Coat - Mix and pour the Sikafloor-21N PurCem (IN) materials on the floor.
Spread to the desired thickness using a notched squeegee, trowel or screed bar.
Take care to spread newly mixed materials across the transition of previous applied
mixes before the surface begins to set. Immediately spike roll the surface to release
trapped air in the matrix. Allow a minimum 14 hour cure period at 20C before light
traffic.
Clean Up Clean all tools and equipment with Sika Equipment Cleaner/Epoxy Thinner. Wash
soiled hands and skin thoroughly in hot soapy water or use Sika Hand Cleaner.
Once hardened, product can only be removed mechanically.
Maintenance Sikafloor PurCem (IN) floors are easily cleaned using a stiff brushing action and or
high-pressure water, preferably warm. Degreasing agents and detergents will
assist, but do not use any compounds containing Phenol as the floor colour may be
damaged. Consult the cleaning compound manufacturers printing directions before
use.
3
Limitations Do not apply below 10C or above 30C / maximum relative humidity 85%.
Do not featheredge.
Do not mix Sikafloor PurCem materials by hand / mechanical mix only.
Do not apply to surfaces where moisture vapour can condense and freeze.
Steam cleaning may lead to delamination due to thermal shock (Use Sikafloor -
20N PurCem (IN) ).
Colour uniformity cannot be completely guaranteed from batch to batch
(numbered). Take care when using Sikafloor PurCem products to draw from
inventory in batch number sequence, do not mix batch numbers in a single floor
area.
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Health and Safety For information and advice on the safe handling, storage and disposal of chemical
Information products, users shall refer to the most recent Material Safety Data Sheet containing
physical, ecological, toxicological and other safety-related data.
4
Legal Notes The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sikas recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose,
nor any liability arising out of any legal relationship whatsoever, can be inferred
either from this information, or from any written recommendations, or from any other
advice offered. The user of the product must test the products suitability for the
intended application and purpose. Sika reserves the right to change the properties
of its products. The proprietary rights of third parties must be observed. All orders
are accepted subject to our current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for the product
concerned, copies of which will be supplied on request.
Construction