Академический Документы
Профессиональный Документы
Культура Документы
2012 ENGINE
Fig. 1: Intake Manifold And Exhaust System Components Location (without SH-AWD)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:15:13
2:15:11 PM Page 1 2005 Mitchell Repair Information Company, LLC.
1
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
Fig. 2: Intake Manifold And Exhaust System Components Location (with SH-AWD)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:15:11 PM Page 2 2005 Mitchell Repair Information Company, LLC.
2
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
REMOVAL
manual
Tuesday, February 16, 2016 2:15:11 PM Page 3 2005 Mitchell Repair Information Company, LLC.
3
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
Fig. 4: Identifying MAP Sensor Connector, Breather Pipe And Intake Air Duct
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Disconnect the throttle actuator connector (A), the EVAP canister purge valve connector (B), the water
bypass hoses (C), the EVAP canister hose (D), the brake booster vacuum hose (E), and the vacuum hose
(F).
Fig. 5: Identifying Throttle Actuator Connector, EVAP Canister Hose And Purge Valve Connector,
Bypass Hose, Vacuum Hose
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Disconnect the PCV hose (A) and the IMT actuator connector (B).
manual
Tuesday, February 16, 2016 2:15:11 PM Page 4 2005 Mitchell Repair Information Company, LLC.
4
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
5. Remove the upper cover mounting bolts and nuts sequentially in three steps, then remove the upper
cover.
Fig. 7: Identifying Bolts And Nuts Of Upper Cover With Loosening Sequence
Courtesy of AMERICAN HONDA MOTOR CO., INC.
6. Remove the intake manifold mounting bolts and nuts sequentially in three steps, then remove the intake
manifold.
manual
Tuesday, February 16, 2016 2:15:11 PM Page 5 2005 Mitchell Repair Information Company, LLC.
5
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
Fig. 8: Identifying Bolts And Nuts Of Intake Manifold With Loosening Sequence
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION
1. Install the intake manifold. Tighten the mounting bolts and nuts sequentially in three steps. Always use a
new intake manifold gasket.
Specified Torque
manual
Tuesday, February 16, 2016 2:15:11 PM Page 6 2005 Mitchell Repair Information Company, LLC.
6
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
Fig. 9: Identifying Bolts And Nuts Of Intake Manifold With Tightening Sequence
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Install the upper cover. Tighten the mounting bolts and nuts sequentially in three steps. Always use a new
gasket.
Specified Torque
Fig. 10: Identifying Bolts And Nuts Of Upper Cover With Tightening Sequence
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Connect the PCV hose (A) and the IMT actuator connector (B).
manual
Tuesday, February 16, 2016 2:15:11 PM Page 7 2005 Mitchell Repair Information Company, LLC.
7
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
4. Connect the throttle actuator connector (A), the EVAP canister purge valve connector (B), the water
bypass hoses (C), the EVAP canister hose (D), the brake booster vacuum hose (E), and the vacuum hose
(F).
5. Install the intake air duct (A), then connect the breather pipe (B) and the MAP sensor connector (C).
Fig. 13: Identifying Intake Air Duct, Breather Pipe And MAP Sensor Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:15:11 PM Page 8 2005 Mitchell Repair Information Company, LLC.
8
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
5. Remove the injector base mounting bolts/nuts (A), then remove the front injector base (B) and the rear
injector base (C).
manual
Tuesday, February 16, 2016 2:15:11 PM Page 9 2005 Mitchell Repair Information Company, LLC.
9
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
Fig. 15: Identifying Mounting Bolts, Front And Rear Injector Base
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION
1. Install the front injector base (A) and the rear injector base (B) with new gaskets (C), and tighten the
injector base mounting bolts/nuts (D) in a crisscross pattern in three steps, beginning with the inner nuts.
NOTE: The front injector base gasket is different from the rear one. Do not mix
injector base gasket types.
manual
Tuesday, February 16, 2016 2:15:11 PM Page 10 2005 Mitchell Repair Information Company, LLC.
10
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
Fig. 16: Identifying Front And Rear Injector Base And Gasket With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Connect the knock sensor connector (A), then install the harness holder mounting bolts (B).
Fig. 17: Identifying Knock Sensor Connector And Holder Mounting Bolts With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
the ON mode (do not operate the starter) so the fuel pump runs for about 2 seconds and pressurizes the
fuel line. Repeat this operation three times, then check for fuel leakage at any point in the fuel line.
NOTE: Use new gaskets and new self-locking nuts when reassembling.
Fig. 18: Identifying Exhaust Pipe And Muffler And Related Components With Torque Specifications (1
Of 2)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:15:11 PM Page 12 2005 Mitchell Repair Information Company, LLC.
12
2012 Acura TL
2012 ENGINE Intake Manifold And Exhaust System - TL
NOTE: Use new gaskets and new self-locking nuts when reassembling.
Fig. 19: Identifying Exhaust Pipe And Muffler And Related Components With Torque Specifications (2
Of 2)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:15:11 PM Page 13 2005 Mitchell Repair Information Company, LLC.
13