Академический Документы
Профессиональный Документы
Культура Документы
Warning
For this version, you must do a two-phase update, update the operating
system first and then
You need to use a USB memory key is recognized by the copier. A list of test
device found in the bulletin Digital-94 and Digital-95. If you use a USB memory
key
More than one of these devices, the best practice is to confirm the update
operation on a
parts numbers and other data stored on the hard drive before doing the
update. in some
case, you need to format the drive after the update. Logs are backed up using
Maintain access from TOP ~ Backup data. The code is the best support
using FSMS.
1. Install Data ROM.bin in the root directory of an empty USB memory device
formatted as FAT (FAT23 does not). This file is found in the rom-bin directory of
download package.
3. Remove any existing USB dongle from the USB port (s) and insert the USB
memory
7. When the operation is finished, turn off the power and unplug the USB
memory device.
1. Copy the update file to the USB memory device. The files go in the root
directory.
The files can also go into a folder with name specific models appropriate if the
copier
model directory
drive F on your computer, you can put the files in F: \. If you are already a
photocopier in
Do not put any files in directories other than the update files updates. USB
2. If the copier model can print or scan enablers installed, uninstall them
first. with
power off, insert the USB memory device into the USB port on the right side of
Photocopiers. Some models have 2 ports: either can be used. Electricity to hold
copiers
4 and 9 keys.
3. Wait about 5 minutes for the following screen will be displayed (screens
Minimum SYS
Version
* This means that the software is selected for updates. Note that by default, the
operating system is de-selected
and all other software is selected. This is not the exact combination
possibilities. specific
select the firmware that needs to be updated. In most cases, you will select all
items. If you
update the computer and scans using EPROM jig, then you will deselect the
goods.
4. Click Start to begin the update process. As each individual from being
updated,
photocopier screen will list that as complete ROM. This process is not complete
until all
ROM has been updated and the screen says "Update completed".
Download Storage -> FROM Update Start. UI Data Update ... Finished
Note 2: The announcement says that the key to the next storage connection is
not correct.
5. When the update has run to completion, each firmware package should be
listed in
Screen photocopiers complete. The screen will display at the bottom: "Xin
When "Please connect to the next important storage ..." message is displayed,
updated
complete. Electrical down copier and remove the USB memory device.
6. Power on the copier mode 08 Code 947. 08. Making Turn off copiers.
7. Power on the copier. If you get the message "Wait, warm UP" and copiers do
not to get ready after waiting a long time, as codes 08-690. Confirm normal
activity. Print out a list of codes 900 through 950 print and compare with the
goals
overview
STEPS
3 PWR / 690 = 2 PWR 0/8 down when rebooting is displayed - replace the HDD
if a restart is not
You just choose 0 AN1 (OS and HDD) for most of the recovery. be sure
NIC is de-selected (Downgrading a NIC card can cause permanent damage).
If you are troubled about the updates of the main USB or Scan to work,
Data download and use EPROM EPROM jig to perform the update.
5 Turn ordinary machine and check the basic copy function, if the basic
functions seem
implementation to step 6, if they do not fix the issue. (See bottom of page)
7. Check all the functions of the machine, if the machine fails, try "Additional
steps".
PERFECT
Additional steps -
If no specific targets (eg, target 13) using DLM table and try to update the table
failed
two above
Touch Panel
If the touch panel is not calibrated in any of the above steps, perform