Академический Документы
Профессиональный Документы
Культура Документы
RClamp0524P
Ultra Low Capacitance TVS Arrays
PROTECTION PRODUCTS - RailClamp PRELIMINARY
Description Features
RailClamp TVS arrays are ultra low capacitance ESD ESD protection for high-speed data lines to
protection devices designed to protect high speed data IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact)
interfaces. This series has been specifically designed to IEC 61000-4-5 (Lightning) 5A (8/20s)
protect sensitive components which are connected to IEC 61000-4-4 (EFT) 40A (5/50ns)
high-speed data and transmission lines from overvolt- Package design optimized for high speed lines
age caused by ESD (electrostatic discharge), CDE Flow-Through design
(Cable Discharge Events), and EFT (electrical fast Protects two or four I/O lines
transients).
Low capacitance: 0.3pF typical (I/O to I/O)
The RClamp0522P and RClamp0524P have a typical Low clamping voltage
capacitance of only 0.30pF between I/O pins. This Low operating voltage: 5V
allows it to be used on circuits operating in excess of
Solid-state silicon-avalanche technology
3GHz without signal attenuation. They may be used to
meet the ESD immunity requirements of IEC 61000-4- Mechanical Characteristics
2, Level 4 (15kV air, 8kV contact discharge). The
SLP1610P4 6-pin package (1.6 x 1.0 x 0.58mm)
RClamp0522P is designed to protect two lines, while
SLP2510P8 10-pin package (2.5 x 1.0 x 0.58mm)
the RClamp0524P will protect four lines.
Pb-Free, Halogen Free, RoHS/WEEE Compliant
The RClamp0522P is in a 6-pin SLP1610P4 package. It
Lead Pitch: 0.5mm
measures 1.6 x 1.0 with a nominal height of 0.58mm.
The RClamp0524P is in a 10-pin SLP2510P8 package.
Lead finish: NiPdAu
It measures 2.5 x 1.0 with a nominal height of 0.58mm. Marking: Marking Code
The leads are spaced at a pitch of 0.5mm and are fin- Packaging: Tape and Reel
ished with lead-free NiPdAu. They are designed for easy Applications
PCB layout by allowing the traces to run straight through
the device. The combination of small size, low capaci-
High Definition Multi-Media Interface (HDMI)
tance, and high level of ESD protection makes them a Digital Visual Interface (DVI)
flexible solution for applications such as HDMI, DisplayPortTM Interface
DisplayPortTM, MDDI, and eSATA interfaces. MDDI Ports
PCI Express
eSATA Interfaces
3, 4 3, 8
RClamp0522P RClamp0524P
6 5 4 10 9 8 7 6
1 2 3 1 2 3 4 5
SLP1610P4 Pin Configuration (Top View) SLP2510P8 Pin Configuration (Top View)
3, 4 3, 8
Ordering Information
Number Qty per Reel
Part Number
of Lines Reel Size
2 www.semtech.com
RClamp0522P
RClamp0524P
PROTECTION PRODUCTS PRELIMINARY
Absolute Maximum Rating
Rating Symbol Value Units
10 110
100
Peak Pulse Power - PPP (kW)
90
0.01 0
0.1 1 10 100 1000 0 25 50 75 100 125 150
Pulse Duration - tp (us) Ambient Temperature - TA (oC)
110 25
100 Waveform
Parameters:
90 tr = 8s 20
Clamping Voltage -VC (V)
70
PP
e-t 15
Percent of I
60
50
10
40 td = IPP/2
Line to Gnd
30 Waveform
5 Parameters:
20
tr = 8s
10 td = 20s
0 0
0 1 2 3 4 5 6
0 5 10 15 20 25 30
Time (s) Peak Pulse Current - IPP (A)
1.6
1.4
1.2
CJ(VR) / CJ(VR=0)
0.8
0.6
0.4
0.2
0
0 1 2 3 4 5
Reverse Voltage - VR (V)
5
2: -0.0442 dB 5 2: -0.2095 dB
0 dB 900 MHz 0 dB 900 MHz
12 12 4
3 4 3
-6 dB 3: -0.4690 dB -6 dB 3: -0.6419 dB
1.8 GHz 1.8 GHz
-12 dB -12 dB
4: -0.5150 dB 4: -0.2029 dB
2.5 GHz 2.5 GHz
-18 dB -18 dB
-24 dB -24 dB
-30 dB -30 dB
-36 dB -36 dB
-42 dB -42 dB
-48 dB -48 dB
1 10 100 1 3 1 10 100 1 3
MHz MHz MHz GHz GHz MHz MHz MHz GHz GHz
START . 030 MHz STOP 3000. 000000 MHz START . 030 MHz STOP 3000. 000000 MHz
HDMI Connector
The RClamp0524P and RClamp0522P are specifically 9
designed for protection of high-speed interfaces such 8
7
as HDMI. They present <0.4pF capacitance between
the pairs while being rated to handle >8kV ESD 1
contact discharges (>15kV air discharge) as outlined 6
5
in IEC 61000-4-2. Each device is in a leadless SLP 4
package that is less than 1.1mm wide. They are GND GND
designed such that the traces flow straight through the 3
device. The narrow package and flow-through design 2
reduces discontinuities and minimizes impact on signal 1
integrity. This becomes even more critical as signal
speeds increase.
Figure 1. Flow through Layout Using
Pin Configuration R Clam p052
Clamp052 4P
p0524P
Figure 1 is an example of how to route the high speed
differential traces through the RClamp0524P. The
solid line represents the PCB trace. The PCB traces
are used to connect the pin pairs for each line (pin 1 to
pin 10, pin 2 to pin 9, pin 4 to pin 7, pin 5 to pin 6).
For example, line 1 enters at pin 1 and exits at Pin 10
and the PCB trace connects pin 1 and 10 together.
This is true for lines connected at pins 2, 4, and 5 also.
Ground is connected at pins 3 and 8. One large
ground pad should be used in lieu of two separate
pads. The same layout rules apply for the
RClamp0522P.
MDDI_Data0+
MDDI_Data0-
Gnd Gnd
MDDI_Data1+
MDDI Link MDDI Link
MDDI_Data1-
Controller Controller
RClamp0524P RClamp0524P
MDDI_Stb+
MDDI_Stb-
Gnd Gnd
RClamp0522P RClamp0522P
Host Pwr
Host Gnd
HOST uClamp0501P uClamp0501P
Parameter Unit D1 D2 D3
A D B DIMENSIONS
INCHES MILLIMETERS
DIM
MIN NOM MAX MIN NOM MAX
A .020 .023 .026 0.50 0.58 0.65
E A1 0.00 .001 .002 0.00 0.03 0.05
PIN 1 A2 (.005) (0.13)
INDICATOR b .006 .008 .010 0.15 0.20 0.25
(LASER MARK) b1 .014 .016 .018 0.35 0.40 0.45
D .059 .063 .067 1.50 1.60 1.70
E .035 .039 .043 0.90 1.00 1.10
e .020 BSC 0.50 BSC
e1 .039 BSC 1.00 BSC
L .012 .015 .017 0.30 0.38 0.43
A N 4 4
SEATING aaa .003 0.08
aaa C PLANE bbb .004 0.10
A2 A1 C
bxN
bbb C A B b1xN
bbb C A B
1 2
R0.125
E/2 LxN
N
2X R0.075
3 PLACES e
e1
D/2
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
P1
P
DIMENSIONS
Y DIM INCHES MILLIMETERS
C (.034) (0.87)
Z (C) G (Y1) G .007 0.19
P .020 0.50
P1 .039 1.00
X .008 0.20
X1 .016 0.40
X Y .027 0.68
X1 Y1 (.061) (1.55)
Z .061 1.55
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
A D B DIMENSIONS
INCHES MILLIMETERS
DIM
MIN NOM MAX MIN NOM MAX
A .020 .023 .026 0.50 0.58 0.65
A1 0.00 .001 .002 0.00 0.03 0.05
PIN 1 E (.005) (0.13)
A2
INDICATOR b .006 .008 .010 0.15 0.20 0.25
(LASER MARK) b1 .014 .016 .018 0.35 0.40 0.45
D .094 .098 .102 2.40 2.50 2.60
E .035 .039 .043 0.90 1.00 1.10
e .020 BSC 0.50 BSC
L .012 .015 .017 0.30 0.38 0.425
N 8 8
A aaa .003 0.08
SEATING
bbb .004 0.10
aaa C PLANE
A2 A1 C
b1xN
R0.125
bbb C A B
1 2
E/2 LxN
2X R0.075
7 PLACES
N
e bxN
bbb C A B
D/2
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
P1
P
DIMENSIONS
DIM INCHES MILLIMETERS
Y C (.034) (0.875)
G .008 0.20
Z (C) (Y1)
G P .020 0.50
P1 .039 1.00
X .008 0.20
X1 .016 0.40
Y .027 0.675
X Y1 (.061) (1.55)
X1 Z .061 1.55
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
0522P PIN 1
0524P
PIN 1 YYWW
YYWW INDICATOR
INDICATOR
Pin 1 Location
Part Number A0 B0 K0
Tape K
B, (Max) D D1 E F P P0 P2 T(MAX) W
Width (MAX)
8.0 mm
0.5 mm 1.750.10
1.5 + 0.1 mm 3.50.05 4.00.1 4.00.1 2.00.05 + 0.3 mm
8 mm 4.2 mm 0.05 mm 2.4 mm 0.4 mm
- 0.0 mm ) mm mm mm mm - 0.1 mm
Contact Information
Semtech Corporation
Protection Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805)498-2111 FAX (805)498-3804