Вы находитесь на странице: 1из 22

Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500

Model AV-1-300 Alarm Check Valve, 300 psi (20,7 bar)


2-1/2, 4, 6, & 8 Inch (DN65, DN100, DN150 & DN200)
Vertical or Horizontal* Installation
General
Description
The Model AV-1-300 Alarm Check
Valves are divided seat ring, rubber
faced clapper, waterflow alarm check
valves that are intended for use in wet
pipe (automatic sprinkler) fire protec-
tion systems. They may be installed
vertically or horizontally*, and they are
designed to automatically actuate
electric and/or hydraulic alarms when
there is a steady flow of water into the
system that is equivalent to the dis-
charge rate of one or more sprinklers.
A separately ordered, Model RC-1 Re-
tard Chamber (TFP920) is required for
installations subject to variable pres-
sures. It is used to help prevent false
alarms associated with pressure vari-
ations in public water supplies.
The AV-1-300 Alarm Check Valve
Trim includes pressure gauges to End Connection Available
monitor system pressure conditions, a Inlet x Outlet
by-pass check valve, a main drain
valve, and an alarm test valve. The Groove Flange Flange
Nominal
x x x
bypass check valve reduces the pos- Valve Size
Groove Groove Flange
sibility of false alarms by permitting
slow as well as small transient in- 2-1/2 Inch
N/A
creases in water supply pressure to be (DN65) 22 lbs. (10,0 Kg) 28 lbs. (12,7 Kg)
passed through to the system without 4 Inch
opening the waterway clapper. (DN100) 45 lbs. (20,4 Kg) 51 lbs. (23,1 Kg) 62 lbs. (28,1 Kg)
6 Inch
WARNING (DN150) 68 lbs. (30,9 Kg) 78 lbs. (35,4 Kg) 93 lbs. (42,2 Kg)
The Model AV-1-300 Alarm Check 8 Inch
Valves described herein must be in- (DN200) 129 lbs. (58,6 Kg) 148 lbs. (67,1 Kg) 167 lbs. (75,8 Kg)
stalled and maintained in compliance
with this document, as well as with the
applicable standards of the National
Fire Protection Association, in addition
to the standards of any other authori-
ties having jurisdiction. Failure to do
so may impair the integrity of these
devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or manufac-
turer should be contacted relative to
any questions. * 4, 6, and 8 Inch (DN100, DN150, and DN200) Valve Sizes

Page 1 of 22 MARCH, 2006 TFP910


Page 2 of 22 TFP910

VALVE PARTS VALVE PARTS REPLACEMENT PARTS


NO.DESCRIPTION QTY. REF. NO. DESCRIPTION QTY. REF. NO. DESCRIPTION P/N
1 Valve Body . . . . . . . 1 NR 12 Handhole Cover (a) Repair Parts Kit,
2 Handhole Cover . . . 1 NR Hex Bolt, Includes 3 & 6
3 Handhole Cover 2-1/2 Inch Valves, 2-1/2 Inch Valve . . . . . . 92-200-1-216
Gasket . . . . . . . . . . 1 See (a) 1/2-13 UNC-2A 4 Inch Valve . . . . . . . . . 92-200-1-416
4 Seat Ring . . . . . . . . 1 NR x 1-1/4" Long . . . . . 4 CH 6 Inch Valve . . . . . . . . . 92-200-1-620
5 Clapper . . . . . . . . . . 1 See (b) 4 Inch Valves, 8 Inch Valve . . . . . . . . . 92-200-1-816
6 Clapper Facing . . . . 1 See (a) or (b) 1/2-13 UNC-2A (b) Clapper Assembly,
7 Clapper Washer . . . 1 See (b) x 1-3/4" Long . . . . . 4 CH Includes 5-9, 11
8 2-1/2 Inch Valve: 6 Inch Valves, 2-1/2 Inch Valve . . . . . . 92-200-1-218
Lock Nut . . . . . . . . . 1 See (b) 1/2-13 UNC-2A Includes 5-11
4, 6, & 8 Inch Valves: x 1-3/4" Long . . . . . 6 CH 4 Inch Valve . . . . . . . . . 92-200-1-423
Hex Self-Locking 8 Inch Valves, 6 Inch Valve . . . . . . . . . 92-200-1-623
Cap Screw . . . . . . . 1 See (b) 3/4-10 UNC-2A 8 Inch Valve . . . . . . . . . 92-200-1-823
9 Clapper Hinge Pin . . 1 See (b) x 2" Long . . . . . . . . . 6 CH
10 Clapper Hinge 13 4, 6, & 8 Inch NOTES:
Pin Bushing, Valves only: 1. F x F valve shown for reference;
2-1/2 Inch Valve . . . 2 NR Clapper Hinge Pin components for G x G and F x G
4, 6, & 8 Inch Square Head Pipe valves are shared.
Valves . . . . . . . . . . . 4 NR Plug, 3/8" NPT . . . . 1 CH 2. NR: Not Replaceable
11 Clapper Spring . . . . 1 See (b)
3. CH: Common Hardware

1
11
11

5
5

10
6
10
7
8 9 13
CLAPPER
ASSEMBLY 6
2-1/2 INCH 7 4
VALVE
8
CLAPPER
ASSEMBLY 2
3
4, 6, & 8 INCH
VALVES 12

The 2-1/2 Inch (DN65) Valves with NPT threaded ports have a 1-1/4 inch main drain connection. The 2-1/2 Inch (DN65) Valves with
ISO threaded ports have a DN40 main drain connection.

The 4, 6, and 8 Inch (DN100. DN150, and DN200) Valves with NPT threaded ports have a 2 inch main drain connection. The 4, 6,
and 8 Inch (DN100. DN150, and DN200) Valves with ISO threaded ports have a DN50 inch main drain connection.

FIGURE 1
2-1/2, 4, 6 & 8 INCH (DN65, DN100, DN150 & DN200) MODEL AV-1-300 ALARM CHECK VALVE
ASSEMBLY
TFP910 Page 3 of 22

FLOW RATE IN LITRES PER MINUTE (LPM)


(1 GPM = 3,785 LPM)
400 600 1000 2000 3000 5000 7000 10000 15000
4.0
IN POUNDS PER SQUARE INCH (PSI)

NOMINAL PRESSURE DROP IN BAR


3.0 0,200
NOMINAL PRESSURE DROP

65)

(1 PSI = 0,06895 BAR)


)

)
100

150
DN

(DN

(DN
H(
2.0

)
00
NC

CH

CH

N2
/2 I

4 IN

6 IN

(D
0,100
2-1

H
NC
0,090

8I
0,080
1.0 0,070
0.9 0,060
0.8
0.7 0,050
100 200 300 400 500 700 1000 2000 3000 4000
FLOW RATE IN GALLONS PER MINUTE (GPM)
The approximate friction loss, based on the Hazen and Williams formula and expressed in equivalent length of pipe with C=120, is as
follows:

14 feet of 2-1/2 inch Sch. 40 pipe for the 2-1/2 inch AV-1-300 Valve calculated on a typical flow rate of 250 GPM.
23 feet of 4 inch Sch. 40 pipe for the 4 inch AV-1-300 Valve calculated on a typical flow rate of 600 GPM.
24 feet of 6 inch Sch. 40 pipe for the 6 inch AV-1-300 Valve calculated on a typical flow rate of 1500 GPM.
23 feet of 8 inch Sch. 30 pipe for the 8 inch AV-1-300 Valve calculated on a typical flow rate of 2500 GPM.
GRAPH A
2-1/2, 4, 6 & 8 INCH (DN65, DN100, DN150 & DN200) MODEL AV-1-300 ALARM CHECK VALVE
NOMINAL PRESSURE LOSS VERSUS FLOW

Flange Drilling Specification


Nominal Dimensions in Inches and (mm)
Nominal
Valve ANSI B16.1 ISO 2084 ISO 2084 JIS B 2210 AS 2129
Size (Class 125) 1 (PN10) 2 (PN16) 3 (10K) (Table E)
Dim. Dim. Qty. Dim. Dim. Qty. Dim. Dim. Qty. Dim. Dim. Qty. Dim. Dim. Qty.
A B N A B N A B N A B N A B N
2-1/2 Inch 5.50 0.75 5.71 0.71 5.51 0.75 5.00 0.71
4 4 4 4
(DN65) (139,7) (19,0) (145,0) (18,0) (140,0) (19,0) (127,0) (18,0)
USE
4 Inch 7.50 0.75 7.09 0.71 6.89 0.75 7.00 0.71
8 ISO 2084 8 8 8
(DN100) (190,5) (19,0) (180,0) (18,0) (175,0) (19,0) (178,0) (18,0)
(PN16)
6 Inch 9.50 0.88 9.45 0.87 9.45 0.91 9.25 0.87
8 8 8 8
(DN150) (241,3) (22,2) (240,0) (22,0) (240,0) (23,0) (235,0) (22,0)
8 Inch 11.75 0.88 11.61 0.87 11.61 0.87 11.42 0.91 11.50 0.87
8 8 12 12 8
(DN200) (298,5) (22,2) (295,0) (22,0) (295,0) (22,0) (290,0) (23,0) (292,0) (22,0)
1
Dim. A Same drilling as for B16.5 (Class 150) and B16.42 (Class 250).
Bolt Circle 2
Same drilling as for BS 4504 Section 3.2 (PN10) and DIN 2532 (PN10).
Diameter 3
Same drilling as for BS 4504 Section 3.2 (PN16) and DIN 2532 (PN16).
Dim. B
Bolt Hole
Diameter

Qty. N
Number of
Bolt Holes

TABLE A
FLANGE DRILLING SPECIFICATIONS
Page 4 of 22 TFP910

Technical WATERFLOW
PRESSURE
ALARM SWITCH
4
Data ONCE RETARD
CHAMBER OVERFLOWS,
WATERFLOW PRESSURE
Approvals: ALARM SWITCH AND
UL and C-UL Listed, as well as FM WATER MOTOR 1
RETARD
Approved. CHAMBER
ALARM ACTUATE
UPON SPRINKLER
WATERFLOW FLOW, WATERWAY
Working Water Pressure Range TO WATER CLAPPER OPENS
20 to 300 psi (1,4 to 20,7 bar). MOTOR ALARM WATERFLOW
Friction Loss TO SYSTEM
7/32"
Refer to Graph A. (5,6 mm) SYSTEM
ORIFICE PRESSURE
Physical Characteristics INLET GAUGE
The body is ductile iron, the handhole RESTRICTION
ASSEMBLY
cover is ductile iron or cast iron, and
the seat ring is bronze. The clapper for 1/8"
the 2-1/2 inch (DN65) valve size is (3,2 mm)
stainless steel. The clapper for the ORIFICE SUPPLY
larger valve sizes is either cast or duc- OUTLET PRESSURE
tile iron. All valve sizes utilize an GAUGE
3
EPDM clapper facing.
WHEN FLOW THROUGH
Flanged connections are available RESTRICTION ASSEMBLY
drilled per ANSI, ISO, AS, and JIS INLET EXCEEDS OUTLET, MAIN
specifications as detailed in Table A. RETARD CHAMBER DRAIN 2
BEGINS TO FILL VALVE WATERFLOW
Threaded port connections for the THROUGH SEAT
AV-1-300 Valves are available NPT RING GROOVE AND
threaded or threaded per ISO 7/1 as ALARM PORT
detailed in the Ordering Procedure
section. Valves with NPT threaded
ports will readily accept the trim ar- FIGURE 2
rangements detailed in Figures 4 2-1/2, 4, 6 & 8 INCH (DN65, DN100, DN150 & DN200)
through 6. MODEL AV-1-300 ALARM CHECK VALVE
OPERATION

Operating
Principles SCREEN

When the fire protection system is in- INLET RESTRTICTION


itially being pressurized, water will flow WITH 0.219" (5.6 mm)
into the system until the water supply ORIFICE
and system pressure become equal-
ized, and the torsion Spring closes the
Clapper in the Alarm Check Valve. DRAIN RESTRTICTION
Once the pressures have stabilized, WITH 0.125" (3.2 mm)
the Alarm Check Valve is in service ORIFICE
and the centrally located groove in the
Seat Ring is sealed. Consequently, FIGURE 3
with the Alarm Check Valve set for RESTRICTION ASSEMBLY
service, there is no flow through the (Provided with Alarm Check Valve Trim)
alarm port to the alarm devices (i.e.,
water motor alarm and/or pressure
alarm switch). water motor alarm and/or the pressure tem (via the bypass check valve) with-
When there is a steady flow of water alarm switch will be actuated. The out opening the Clapper. A transient
into the sprinkler system due to a alarms will continue to be actuated as surge in supply pressure which is suf-
sprinkler operation, the Clapper opens long as the Clapper remains opened. ficient to only momentarily open the
as shown in Figure 2. Water is then Water in the alarm lines will automat- Clapper will not cause a false alarm,
permitted to flow into the centrally lo- ically drain out through the 1/8 inch and a portion of the increase in pres-
cated groove in the Seat Ring and out (3,2 mm) drain orifice in the Restriction sure will be trapped within the system,
through the alarm port towards the Re- Assembly (Figure 3) when the Clapper thus reducing the possibility of another
striction Assembly (Figure 3). When closes (due to a discontinuation in the opening. Any water in the alarm line is
the flow through the inlet restriction of flow of water into the sprinkler sys- automatically drained, further reduc-
the Restriction Assembly exceeds the tem). ing the possibility of a false alarm due
flow through the outlet restriction, the to a successive transient surge in sup-
In the case of variable pressure sys-
Retard Chamber (where provided in ply pressure.
tems, slow as well as small transient
the case of systems with variable pres- increases in water supply pressure
sure), begins to fill. Subsequently, the may continue to be built up in the sys-
TFP910 Page 5 of 22

could also cause the waterway Clap-


Design Criteria Installation per to cycle open and shut during an
inspectors test or during a discharge
In planning the installation, considera- NOTES by a single sprinkler.
tion must be given to the disposal of Proper operation of the Model AV-1-
the large quantities of water that may 300 Alarm Check Valves depends
be associated with draining the system upon the trim described in this data
or performing a flow test. sheet being installed in accordance
Valves installed in the vertical position with the following instructions. Failure
must have the flow going up. Valves to follow the appropriate trim installa-
installed in the horizontal position must tion instructions may prevent the de-
be positioned so that the drain connec- vice from functioning properly as well
tion points down. as void listings/approvals, and the
manufacturers warranties.
The sprinkler system designer must be
aware that the configuration of the pip- The Alarm Check Valves must be in-
ing network and its tendency to trap stalled in readily visible and accessible
pockets of air (such as in the case of a locations.
peaked-roof gridded system) can af- It is recommended that provision be
fect the performance of the alarm sys- made for viewing the alarm line drain
tem. Although a slight amount of water by locating the main drain outlet
trapped air is desirable to prevent sig- in a readily visible area.
nificant pressure increases due to
thermally induced expansion of the Wet pipe fire protection systems must
water, a large quantity of trapped air in be maintained at a minimum tempera-
a system may result in the possibility ture of 40F/4C.
of an intermittent alarm. Step 1. Trim the Alarm Check Valve in
The possibility of an intermittent alarm accordance with Figure 4, 5, or 6, as
condition is a consequence of the fact applicable. Apply pipe thread sealant
that the flow out of the system through sparingly to male threads only.
the test valve or a single sprinkler is Step 2. The Alarm Vent Trim illus-
very small relative to the flow that can trated in Figure 8 must be installed if a
be passed through the valve. This dif- water motor alarm is not to be used.
ference increases with valve size. If
the system were free of trapped air, Step 3. Plug unused alarm connec-
flow in would equal flow out and the tions.
Clapper would always stabilize at Step 4. Suitable provision must be
some open position (as needed to ac- made for disposal of alarm line and
commodate the required flow). With system drainage water. Drainage
trapped air in the system, however, the water must be directed so that it will
Clapper first opens wider since the not cause damage or result in danger-
system initially demands greater flow ous conditions.
until the air pockets are compressed
(back to nearly the supply pressure), Step 5. The alarm line drain must be
and then it will tend to return closer to arranged so that there will be no dan-
the Seat Ring. If the volume of the air ger of freezing.
pockets is excessive, flow into the sys- Step 6. The check valve in the exter-
tem can be momentarily reduced to nally mounted bypass around the wa-
nearly zero (once the air pockets are terway Clapper must be installed with
compressed) and the Clapper may its arrow pointed up, and the drain
close, causing flow to the alarms to be check valve must be installed with its
shutoff. arrow pointing towards the drain.
Once the Clapper has closed, suffi- Step 7. It is recommended that a vent
cient water must flow out of the system connection (which may also be used
before the Clapper will again open. A as an end-of-line Inspectors Test
repetition of the above described con- Connection), be piped from a cross
dition is termed an intermittent alarm. main or branch line at the point most
Using a vent (which can also serve as remote from the alarm valve. The vent
an end-of-line Inspectors Test Con- line should be connected to the top of
nection) piped from the top of a cross a cross main or to the end of a branch
main or end of a branch line at the line and be located at the highest level
point most remote from the alarm of a multi-level installation.
valve, and filling the system slowly in The vent connection can be used to
accordance with the steps described bleedoff excessive air from the sys-
in the Setting Procedure section, can tem, and therefore, minimize the pos-
prevent an excessive amount of air sibility of a false alarm due to a tran-
from being trapped. sient surge in supply pressure. The
contraction/expansion associated with
an excessive amount of trapped air
Page 6 of 22 TFP910

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 17 1/2" x 1/4" x 1/2" Tee . . . . 2 CH
Water Pressure Gauge . . 2 92-343-1-005 18 1/2" x 1/2" x 3/4" Tee . . . . 1 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 19 1-1/4" x 1-1/4" x 1/2" Tee 1 CH
3 1/2" Swing Check Valve . 2 46-049-1-004 20 1/4" x 1" Nipple . . . . . . . . 2 CH
4 1/2" Globe Valve . . . . . . . 1 46-047-1-004 21 1/4" x 2-1/2" Nipple . . . . . 1 CH
5 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 22 1/2" x 1-1/2" Nipple . . . . . 7 CH
6 Restriction Assembly . . . . 1 92-210-2-005 23 1/2" x 2" Nipple . . . . . . . . 2 CH
7 1-1/4" Angle Valve . . . . . . 1 46-048-1-007 24 1/2" x 2-1/2" Nipple . . . . . 1 CH
8 External By-Pass Tube . . 1 92-304-1-017 25 1/2" x 3" Nipple . . . . . . . . 1 CH
9 Alarm Test Tube . . . . . . . 1 92-304-1-047 26 1/2" x 4" Nipple . . . . . . . . 1 CH
10 1/2" NPT x 1/2" Tube 27 1/2" x 6" Nipple . . . . . . . . 1 CH
Connector . . . . . . . . . . . . 2 92-304-1-015 28 1-1/4" x 2-1/2" Nipple . . . . 1 CH
11 1/2" NPT x 5/8" Tube 29 1-1/4" x 3-1/2" Nipple . . . . 1 CH
Connector . . . . . . . . . . . . 2 92-304-1-013
12 1/4" Plug . . . . . . . . . . . . . 2 CH
13 1/2" Union . . . . . . . . . . . . 1 CH NOTES:
14 1/4" 90 Elbow . . . . . . . . . 1 CH 1. All Fittings and Nipples are galvanized
15 1/2" 90 Elbow . . . . . . . . . 1 CH (Standard Order).
16 1/2" Tee . . . . . . . . . . . . . . 2 CH
2. CH: Common Hardware.

1/2 INCH NPT


CONNECTION
FOR WATERFLOW
PRESSURE ALARM
SWITCH
3/4 INCH NPT
LOCATION CONNECTION FOR
WATER MOTOR EXTERNAL
FOR OPTIONAL
ALARM BY-PASS
ELECTRICALLY
TUBE ALARM
SUPERVISED
8 TEST TUBE
N.O. ALARM 1/2 INCH NPT ALARM 11 9
CONTROL VALVE CONNECTION TEST VALVE 3 10
(BVS-3/4") FOR WATERFLOW (NORMALLY 23 1
SYSTEM
PRESSURE ALARM CLOSED) 11
PRESSURE
SWITCH
MODEL RC-1 20 GAUGE
RETARD 3/4 INCH NPT 17 12
CHAMBER CONNECTION FOR 1
18 25 SUPPLY
WATER MOTOR 16 2
ALARM 10 22 PRESSURE
ORDERED 4 GAUGE
SEPARATELY LOCATION 23 14 12
(FOR VARIABLE FOR OPTIONAL 20
5 16 17 21
PRESSURE ELECTRICALLY 22 27 24 2
26
SYSTEMS) SUPERVISED
22
N.O. ALARM
CONTROL VALVE 6 MODEL AV-1
(BVS-1/2") ALARM VALVE,
MAIN 2-1/2 INCH (DN65)
DRAIN VALVE 28 GROOVE x GROOVE
22 (NORMALLY 7 SHOWN
RESTRICTION CLOSED)
ASSEMBLY, 29
SEE FIGURE 3
19

1-1/4 INCH NPT


15 22 13 22 3 22 CONNECTION
TO DRAIN

FIGURE 4 PART 1 OF 3
VERTICAL CLOSED DRAIN TRIM STANDARD ORDER
FOR 2-1/2 INCH (DN65) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-050)
TFP910 Page 7 of 22

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 22 1/2" x 3" Nipple . . . . . . . . 2 CH
Water Pressure Gauge . . 2 92-343-1-005 23 1/2" x 3-1/2" Nipple . . . . . 1 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 24 1/2" x 5" Nipple . . . . . . . . 1 CH
3 1/2" Swing Check Valve . 2 46-049-1-004 25 1/2" x 5-1/2" Nipple . . . . . 1 CH
4 1/2" Globe Valve . . . . . . . 1 46-047-1-004 26 1/2" x 6-1/2" Nipple . . . . . 1 CH
5 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 27 Select Nipple per Table . . 2 CH
6 Restriction Assembly . . . . 1 92-210-2-005 28 Select Nipple per Table . . 2 CH
7 2" Angle Valve . . . . . . . . . 1 46-048-1-009 29 2" x 3" Nipple . . . . . . . . . . 2 CH
8 1/4" Plug . . . . . . . . . . . . . 2 CH
9 1/2" x 1/4" Reducing
Bushing . . . . . . . . . . . . . . 1 CH Select Appropriate Nipple Sizes
10 1/2" Union . . . . . . . . . . . . 3 CH Nipple per AV-1 Alarm Check Valve Size
11 1/2" 90 Elbow . . . . . . . . . 4 CH Number
4 Inch (DN100) 6 Inch (DN150)
12 1/2" 45 Elbow . . . . . . . . . 1 CH
13 1/2" x 1/4" x 1/2" Tee . . . . 1 CH 27 1/2" x 1-1/2" 1/2" x 2-1/2"
14 1/2" x 1/2" x 3/4" Tee . . . . 1 CH 28 1/2" x 3-1/2" 1/2" x 4-1/2"
15 1/2" Tee . . . . . . . . . . . . . . 1 CH
16 2" x 2" x 1/2" Tee . . . . . . . 1 CH
17 1/4" x Close Nipple . . . . . 1 CH NOTES:
18 1/4" x 4" Nipple . . . . . . . . 1 CH 1. Install subassemblies in alphabetical order.
19 1/2" x Close Nipple . . . . . 4 CH 2. All Fittings and Nipples are galvanized
20 1/2" x 1-1/2" Nipple . . . . . 5 CH (Standard Order).
21 1/2" x 2" Nipple . . . . . . . . 2 CH
3. CH: Common Hardware.

1/2 INCH NPT 3/4 INCH NPT


CONNECTION CONNECTION FOR
FOR WATERFLOW WATER MOTOR
PRESSURE ALARM ALARM
SWITCH

LOCATION 1/2 INCH NPT 1/2" x 1-1/2" ALARM


FOR OPTIONAL CONNECTION (4 INCH VALVE) TEST VALVE
ELECTRICALLY FOR WATERFLOW or (NORMALLY
1/2" x 2-1/2" 1/2" x 3-1/2" 1 SYSTEM
SUPERVISED PRESSURE ALARM CLOSED)
(6 INCH VALVE) (4 INCH VALVE) PRESSURE
N.O. ALARM SWITCH or
1/2" x 4-1/2" GAUGE
CONTROL VALVE 11
(BVS-3/4") 3/4 INCH NPT (6 INCH VALVE) 2 8
21
CONNECTION FOR 9
4
WATER MOTOR
ALARM
27
23 F 18 E
MODEL RC-1
RETARD 10 1 SUPPLY
CHAMBER
14 15
I J 28 PRESSURE
26 GAUGE
5 25
19 G 2 8
ORDERED
SEPARATELY LOCATION 22
20
(FOR VARIABLE FOR OPTIONAL H 11 17 D
PRESSURE ELECTRICALLY 12 13
SUPERVISED 20
SYSTEMS) 3 20
N.O. ALARM
22
A 10
CONTROL VALVE 24
20 21
(BVS-1/2") L
6 B
7 11
RESTRICTION 19 29 MODEL AV-1
ASSEMBLY,
C MAIN ALARM VALVE,
SEE FIGURE 3 M DRAIN VALVE 6 INCH (DN150)
(NORMALLY FLANGE x FLANGE
10 N 29
CLOSED) SHOWN
16
11 2 INCH NPT
19 19 3 20 K CONNECTION
TO DRAIN

FIGURE 4 PART 2 OF 3
VERTICAL CLOSED DRAIN TRIM STANDARD ORDER SEMI-PREASSEMBLED
FOR 4 & 6 INCH (DN100 & DN150) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-951)
Page 8 of 22 TFP910

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 22 1/2" x 2" Nipple . . . . . . . . 1 CH
Water Pressure Gauge . . 2 92-343-1-005 23 1/2" x 3" Nipple . . . . . . . . 1 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 24 1/2" x 3-1/2" Nipple . . . . . 2 CH
3 1/2" Swing Check Valve . 1 46-049-1-004 25 1/2" x 4-1/2" Nipple . . . . . 2 CH
4 3/4" Swing Check Valve . 1 46-049-1-005 26 1/2" x 6-1/2" Nipple . . . . . 1 CH
5 1/2" Globe Valve . . . . . . . 1 46-047-1-004 27 3/4" x Close Nipple . . . . . 2 CH
6 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 28 3/4" x 1-1/2" Nipple . . . . . 1 CH
7 Restriction Assembly . . . . 1 92-210-2-005 29 3/4" x 2-1/2" Nipple . . . . . 1 CH
8 2" Angle Valve . . . . . . . . . 1 46-048-1-009 30 3/4" x 3" Nipple . . . . . . . . 1 CH
9 1/4" Plug . . . . . . . . . . . . . 2 CH 31 3/4" x 4-1/2" Nipple . . . . . 1 CH
10 1/2" Union . . . . . . . . . . . . 2 CH 32 2" x 3" Nipple . . . . . . . . . . 1 CH
11 3/4" Union . . . . . . . . . . . . 1 CH 33 2" x 3-1/2" Nipple . . . . . . . 1 CH
12 1/2" 90 Elbow . . . . . . . . . 2 CH
13 1/2" 45 Elbow . . . . . . . . . 1 CH
14 1/2" Tee . . . . . . . . . . . . . . 1 CH
15 1/2" x 1/2" x 3/4" Tee . . . . 1 CH
16 3/4" x 1/4" x 3/4" Tee . . . . 2 CH
17 3/4" x 3/4" x 1/2" Tee . . . . 1 CH NOTES:
18 2" x 2" x 1/2" Tee . . . . . . . 1 CH 1. Install subassemblies in alphabetical order.
19 1/4" x 1-1/2" Nipple . . . . . 2 CH 2. All Fittings and Nipples are galvanized
20 1/2" x Close Nipple . . . . . 3 CH (Standard Order).
21 1/2" x 1-1/2" Nipple . . . . . 3 CH 3. CH: Common Hardware.

1/2 INCH NPT 3/4 INCH NPT


CONNECTION CONNECTION FOR
FOR WATERFLOW WATER MOTOR
PRESSURE ALARM ALARM
SWITCH

LOCATION 1/2 INCH NPT ALARM


FOR OPTIONAL CONNECTION SYSTEM
TEST VALVE
ELECTRICALLY FOR WATERFLOW PRESSURE
(NORMALLY
SUPERVISED PRESSURE ALARM GAUGE
CLOSED)
N.O. ALARM SWITCH
CONTROL VALVE 12
(BVS-3/4") 3/4 INCH NPT 22
G B 19
16 9
CONNECTION FOR 1
WATER MOTOR F C
27
ALARM 24 11
MODEL RC-1 27 2
RETARD 10 5
15 14 25
CHAMBER 26 24 4
25 29 9
6 1
20 D 31
ORDERED
30 2
SEPARATELY LOCATION 19 SUPPLY
(FOR VARIABLE FOR OPTIONAL E 16 PRESSURE
PRESSURE ELECTRICALLY 13 28 GAUGE
SYSTEMS) SUPERVISED MAIN 17
N.O. ALARM DRAIN VALVE
23 (NORMALLY
CONTROL VALVE 21
(BVS-1/2") CLOSED)
I
7
8
RESTRICTION 21 32
MODEL AV-1
ASSEMBLY,
A ALARM VALVE,
SEE FIGURE 3 J 8 INCH (DN200)
33 FLANGE x GROOVE
10 K SHOWN
18
12 2 INCH NPT
20 20 3 21 H CONNECTION
TO DRAIN

FIGURE 4 PART 3 OF 3
VERTICAL CLOSED DRAIN TRIM STANDARD ORDER SEMI-PREASSEMBLED
FOR 8 INCH (DN200) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-952)
TFP910 Page 9 of 22

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 18 1/4" 90 Elbow . . . . . . . . . 1 CH
Water Pressure Gauge . . 2 92-343-1-005 19 1/2" Tee . . . . . . . . . . . . . . 2 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 20 1/2" x 1/4" x 1/2" Tee . . . . 2 CH
3 1/2" Swing Check Valve . 1 46-049-1-004 21 1/2" x 1/2" x 3/4" Tee . . . . 1 CH
4 1/2" Globe Valve . . . . . . . 1 46-047-1-004 22 1-1/4" x 1-1/4" x 1/2" Tee 2 CH
5 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 23 1/4" x 1" Nipple . . . . . . . . 2 CH
6 Restriction Assembly . . . . 1 92-210-2-005 24 1/4" x 2-1/2" Nipple . . . . . 1 CH
7 1-1/4" Angle Valve . . . . . . 1 46-048-1-007 25 1/2" x 1-1/2" Nipple . . . . . 3 CH
8 External By-Pass Tube . . 1 92-304-1-017 26 1/2" x 2" Nipple . . . . . . . . 2 CH
9 Alarm Test Tube . . . . . . . 1 92-304-1-047 27 1/2" x 2-1/2" Nipple . . . . . 1 CH
10 1/2" NPT x 1/2" Tube 28 1/2" x 3" Nipple . . . . . . . . 1 CH
Connector . . . . . . . . . . . . 2 92-304-1-015 29 1/2" x 4" Nipple . . . . . . . . 1 CH
11 1/2" NPT x 5/8" Tube 30 1/2" x 5" Nipple . . . . . . . . 1 CH
Connector . . . . . . . . . . . . 2 92-304-1-013 31 1-1/4" x 2-1/2" Nipple . . . . 2 CH
12 Support Bar . . . . . . . . . . . 1 92-304-1-014 32 1-1/4" x 8-1/2" Nipple . . . . 1 CH
13 Jam Nut . . . . . . . . . . . . . . 1 92-640-1-037
14 PVC Nipple . . . . . . . . . . . 1 92-640-1-009 NOTES:
15 Support Bracket . . . . . . . . 1 92-343-1-006 1. All Fittings and Nipples are galvanized
16 Drip Funnel . . . . . . . . . . . 1 92-343-1-007 (Standard Order).
1/2 INCH NPT 17 1/4" Plug . . . . . . . . . . . . . 2 CH
CONNECTION 2. CH: Common Hardware.
FOR WATERFLOW
PRESSURE ALARM
SWITCH
3/4 INCH NPT
LOCATION CONNECTION FOR
FOR OPTIONAL WATER MOTOR EXTERNAL
ELECTRICALLY ALARM BY-PASS
SUPERVISED TUBE ALARM
N.O. ALARM 1/2 INCH NPT 8 TEST TUBE
CONTROL VALVE ALARM 11 9
CONNECTION TEST VALVE 3 10
(BVS-3/4") FOR WATERFLOW 26 1
(NORMALLY SYSTEM
PRESSURE ALARM CLOSED) 11
SWITCH PRESSURE
MODEL RC-1 23 GAUGE
RETARD 3/4 INCH NPT 20 17
CHAMBER CONNECTION FOR 1
21 WATER MOTOR 28 SUPPLY
19 2
ALARM 10 25 PRESSURE
ORDERED 4 GAUGE
SEPARATELY LOCATION 26 18 17
(FOR VARIABLE FOR OPTIONAL 23
5 19 24
PRESSURE ELECTRICALLY 25 20
30 27 29 2
SYSTEMS) SUPERVISED
25 31
N.O. ALARM 7
CONTROL VALVE 6 13 MODEL AV-1
(BVS-1/2") 14 15 ALARM VALVE,
2-1/2 INCH (DN65)
GROOVE x GROOVE
RESTRICTION MAIN SHOWN
ASSEMBLY, SUPPORT DRAIN VALVE
16
SEE FIGURE 3 BRACKET (NORMALLY
32 CLOSED)
DRIP 31 12
FUNNEL
22 22

1-1/4 INCH NPT 1-1/4 INCH NPT


CONNECTION SUPPORT CONNECTION
TO DRAIN BAR TO DRAIN

FIGURE 5 PART 1 OF 3
VERTICAL OPEN DRAIN TRIM SPECIAL ORDER
FOR 2-1/2 INCH (DN65) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-053)
Page 10 of 22 TFP910

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 22 1/2" x 1-1/2" Nipple . . . . . 4 CH
Water Pressure Gauge . . 2 92-343-1-005 23 1/2" x 2" Nipple . . . . . . . . 2 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 24 1/2" x 3" Nipple . . . . . . . . 1 CH
3 1/2" Swing Check Valve . 1 46-049-1-004 25 1/2" x 3-1/2" Nipple . . . . . 1 CH
4 1/2" Globe Valve . . . . . . . 1 46-047-1-004 26 1/2" x 5" Nipple . . . . . . . . 1 CH
5 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 27 1/2" x 5-1/2" Nipple . . . . . 1 CH
6 Restriction Assembly . . . . 1 92-210-2-005 28 1/2" x 6-1/2" Nipple . . . . . 1 CH
7 2" Angle Valve . . . . . . . . . 1 46-048-1-009 29 Select Nipple per Table . . 2 CH
8 Drip Funnel Connector . . 1 92-211-1-005 30 Select Nipple per Table . . 2 CH
9 Drip Funnel Bracket . . . . 1 92-211-1-003 31 2" x 3" Nipple . . . . . . . . . . 1 CH
10 Drip Funnel . . . . . . . . . . . 1 92-343-1-007
11 1/4" Plug . . . . . . . . . . . . . 2 CH Select Appropriate Nipple Sizes
12 1/2" x 1/4" Reducing Nipple per AV-1 Alarm Check Valve Size
Bushing . . . . . . . . . . . . . . 1 CH Number
4 Inch (DN100) 6 Inch (DN150)
13 1/2" Union . . . . . . . . . . . . 2 CH
14 1/2" 90 Elbow . . . . . . . . . 3 CH 29 1/2" x 1-1/2" 1/2" x 2-1/2"
15 1/2" 45 Elbow . . . . . . . . . 1 CH 30 1/2" x 3-1/2" 1/2" x 4-1/2"
16 1/2" x 1/4" x 1/2" Tee . . . . 1 CH
17 1/2" x 1/2" x 3/4" Tee . . . . 1 CH NOTES:
18 1/2" Tee . . . . . . . . . . . . . . 2 CH 1. Install subassemblies in alphabetical order.
19 1/4" x Close Nipple . . . . . 1 CH 2. All Fittings and Nipples are galvanized
20 1/4" x 4" Nipple . . . . . . . . 1 CH (Standard Order).
21 1/2" x Close Nipple . . . . . 3 CH
3. CH: Common Hardware.

1/2 INCH NPT 3/4 INCH NPT


CONNECTION CONNECTION FOR
FOR WATERFLOW WATER MOTOR
PRESSURE ALARM ALARM
SWITCH

LOCATION 1/2 INCH NPT 1/2" x 1-1/2" ALARM


FOR OPTIONAL CONNECTION (4 INCH VALVE) TEST VALVE
ELECTRICALLY FOR WATERFLOW or (NORMALLY
1/2" x 2-1/2" 1/2" x 3-1/2" 1 SYSTEM
SUPERVISED PRESSURE ALARM CLOSED)
(6 INCH VALVE) (4 INCH VALVE) PRESSURE
N.O. ALARM SWITCH or
1/2" x 4-1/2" GAUGE
CONTROL VALVE 14
(BVS-3/4") 3/4 INCH NPT (6 INCH VALVE) 2 11
23
CONNECTION FOR 12
4
WATER MOTOR
ALARM
29
25 F 20 E
MODEL RC-1
RETARD 13 1 SUPPLY
CHAMBER
17 18
I J 30 PRESSURE
28 GAUGE
5 27
21 G 2 11
ORDERED
SEPARATELY LOCATION 24
22
(FOR VARIABLE FOR OPTIONAL H 14 19 D
PRESSURE ELECTRICALLY 15 16
SUPERVISED 22
SYSTEMS) 3 22
18
N.O. ALARM 21 A 13
CONTROL VALVE 26
22 21 23
(BVS-1/2")
6 8 B
7 14
RESTRICTION 10 31 MODEL AV-1
ASSEMBLY,
C MAIN ALARM VALVE,
9 DRAIN VALVE 6 INCH (DN150)
SEE FIGURE 3
K (NORMALLY FLANGE x FLANGE
DRIP CLOSED) SHOWN
FUNNEL
1-1/4 INCH NPT
CONNECTION 2 INCH NPT
TO DRAIN CONNECTION
TO DRAIN

FIGURE 5 PART 2 OF 3
VERTICAL OPEN DRAIN TRIM SPECIAL ORDER SEMI-PREASSEMBLED
FOR 4 & 6 INCH (DN100 & DN150) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-954)
TFP910 Page 11 of 22

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 20 1/4" x 1-1/2" Nipple . . . . . 2 CH
Water Pressure Gauge . . 2 92-343-1-005 21 1/2" x Close Nipple . . . . . 3 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 22 1/2" x 1-1/2" Nipple . . . . . 1 CH
3 3/4" Swing Check Valve . 1 46-049-1-005 23 1/2" x 2" Nipple . . . . . . . . 1 CH
4 1/2" Globe Valve . . . . . . . 1 46-047-1-004 24 1/2" x 3-1/2" Nipple . . . . . 2 CH
5 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 25 1/2" x 4-1/2" Nipple . . . . . 2 CH
6 Restriction Assembly . . . . 1 92-210-2-005 26 1/2" x 6-1/2" Nipple . . . . . 1 CH
7 2" Angle Valve . . . . . . . . . 1 46-048-1-009 27 3/4" x Close Nipple . . . . . 2 CH
8 Drip Funnel Connector . . 1 92-211-1-005 28 3/4" x 1-1/2" Nipple . . . . . 1 CH
9 Drip Funnel Bracket . . . . 1 92-211-1-003 29 3/4" x 2-1/2" Nipple . . . . . 1 CH
10 Drip Funnel . . . . . . . . . . . 1 92-343-1-007 30 3/4" x 3" Nipple . . . . . . . . 1 CH
11 1/4" Plug . . . . . . . . . . . . . 2 CH 31 3/4" x 4-1/2" Nipple . . . . . 1 CH
12 1/2" Union . . . . . . . . . . . . 1 CH 32 2" x 3" Nipple . . . . . . . . . . 1 CH
13 3/4" Union . . . . . . . . . . . . 1 CH
14 1/2" 90 Elbow . . . . . . . . . 1 CH
15 1/2" 45 Elbow . . . . . . . . . 1 CH NOTES:
16 1/2" Tee . . . . . . . . . . . . . . 2 CH 1. Install subassemblies in alphabetical order.
17 1/2" x 1/2" x 3/4" Tee . . . . 1 CH 2. All Fittings and Nipples are galvanized
18 3/4" x 1/4" x 3/4" Tee . . . . 2 CH (Standard Order).
19 3/4" x 3/4" x 1/2" Tee . . . . 1 CH 3. CH: Common Hardware.

1/2 INCH NPT 3/4 INCH NPT


CONNECTION CONNECTION FOR
FOR WATERFLOW WATER MOTOR
PRESSURE ALARM ALARM
SWITCH

LOCATION 1/2 INCH NPT ALARM


FOR OPTIONAL CONNECTION SYSTEM
TEST VALVE
ELECTRICALLY FOR WATERFLOW PRESSURE
(NORMALLY
SUPERVISED PRESSURE ALARM GAUGE
CLOSED)
N.O. ALARM SWITCH
CONTROL VALVE 14
(BVS-3/4") 3/4 INCH NPT 23
G B 20
18 11
CONNECTION FOR 1
WATER MOTOR F C
27
ALARM 24 13
MODEL RC-1 27 2
RETARD 12 4
17 16 25
CHAMBER 26 24 3
25 29 11
5 1
21 D 31
ORDERED
30 2
SEPARATELY LOCATION 20 SUPPLY
(FOR VARIABLE FOR OPTIONAL E 18 PRESSURE
PRESSURE ELECTRICALLY 15 28 GAUGE
SYSTEMS) SUPERVISED MAIN 19
16 21 DRAIN VALVE
N.O. ALARM
CONTROL VALVE (NORMALLY
22 21
(BVS-1/2") CLOSED)
6 8
7
RESTRICTION 10 32
MODEL AV-1
ASSEMBLY,
A ALARM VALVE,
9
SEE FIGURE 3 8 INCH (DN200)
H FLANGE x GROOVE
DRIP SHOWN
FUNNEL 2 INCH NPT
CONNECTION
1-1/4 INCH NPT TO DRAIN
CONNECTION
TO DRAIN

FIGURE 5 PART 3 OF 3
VERTICAL OPEN DRAIN TRIM SPECIAL ORDER SEMI-PREASSEMBLED
FOR 8 INCH (DN200) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-955)
Page 12 of 22 TFP910

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 21 1/2" x 5" Nipple . . . . . . . . 1 CH
Water Pressure Gauge . . 2 92-343-1-005 22 1/2" x 5-1/2" Nipple . . . . . 1 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 23 Select Nipple per Table . . 2 CH
3 1/2" Swing Check Valve . 2 46-049-1-004 24 Select Nipple per Table . . 2 CH
4 1/2" Globe Valve . . . . . . . 1 46-047-1-004 25 Select Nipple per Table . . 2 CH
5 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 26 2" x 2-1/2" Nipple . . . . . . . 2 CH
6 Restriction Assembly . . . . 1 92-210-2-005
7 2" Globe Valve . . . . . . . . . 1 46-047-1-009
8 1/4" Plug . . . . . . . . . . . . . 2 CH Select Appropriate Nipple Sizes
9 1/2" Union . . . . . . . . . . . . 3 CH Nipple per AV-1 Alarm Check Valve Size
10 1/2" 90 Elbow . . . . . . . . . 5 CH Number
4 Inch (DN100) 6 Inch (DN150)
11 1/2" x 1/4" x 1/2" Tee . . . . 1 CH
12 1/2" x 1/2" x 3/4" Tee . . . . 1 CH 23 1/2" x 1-1/2" 1/2" x 2-1/2"
13 1/2" Tee . . . . . . . . . . . . . . 1 CH 24 1/2" x 3-1/2" 1/2" x 4-1/2"
14 2" x 2" x 1/2" Tee . . . . . . . 1 CH 25 1/2" x 7" 1/2" x 8"
15 1/4" x Close Nipple . . . . . 1 CH
16 1/4" x 4" Nipple . . . . . . . . 1 CH
17 1/2" x 1-1/2" Nipple . . . . . 8 CH NOTES:
18 1/2" x 2" Nipple . . . . . . . . 3 CH 1. All Fittings and Nipples are galvanized
19 1/2" x 3" Nipple . . . . . . . . 2 CH (Standard Order).
20 1/2" x 3-1/2" Nipple . . . . . 1 CH
2. CH: Common Hardware.

3/4 INCH NPT 1/2 INCH NPT SYSTEM


CONNECTION CONNECTION PRESSURE
FOR WATER FOR WATERFLOW GAUGE
MOTOR PRESSURE SUPPLY
ORDERED 1
ALARM ALARM SWITCH PRESSURE
SEPARATELY
8 2 GAUGE
(FOR VARIABLE
LOCATION PRESSURE 1
FOR OPTIONAL SYSTEMS)
8 2
ELECTRICALLY ALARM
SUPERVISED 15
TEST VALVE 16
N.O. ALARM (NORMALLY 11 HANDHOLE
CONTROL MODEL RC-1
CLOSED) COVER MUST
VALVE RETARD
BE AT LEAST
(BVS-3/4") CHAMBER
30 INCHES
24 19 AWAY FROM
1/2 INCH NPT 4 A WALL
CONNECTION 20
FOR WATERFLOW
PRESSURE
ALARM
SWITCH 1/2" x 1-1/2" 10 1/2" x 3-1/2"
(4 INCH 18 (4 INCH
VALVE) VALVE)
3/4 INCH NPT or or
9
CONNECTION 1/2" x 2-1/2" 1/2" x 4-1/2"
FOR WATER (6 INCH (6 INCH
MOTOR 12 VALVE) VALVE)
ALARM 23 26
22
1/2" x 7" 7 MODEL AV-1
LOCATION (4 INCH ALARM VALVE,
13
FOR OPTIONAL VALVE) 17 6 INCH (DN150)
ELECTRICALLY or
1/2" x 8" 3 FLANGE x FLANGE
SUPERVISED SHOWN
(6 INCH
N.O. ALARM 17
17 VALVE)
CONTROL 21 MAIN
VALVE 6 25
18 19 26 DRAIN VALVE
(BVS-1/2") 10 (NORMALLY
17 14
17 9 CLOSED)
RESTRICTION 18
ASSEMBLY, 10
9
SEE FIGURE 3 17 5 17 2 INCH NPT
10 17 3
10 CONNECTION
TO DRAIN

FIGURE 6 PART 1 OF 2
HORIZONTAL CLOSED DRAIN TRIM SPECIAL ORDER
FOR 4 & 6 INCH (DN100 & DN150) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-057)
TFP910 Page 13 of 22

NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N


1 300 psi/ 2000 kPa 22 1/2" x 3-1/2" Nipple . . . . . 2 CH
Water Pressure Gauge . . 2 92-343-1-005 23 1/2" x 4-1/2" Nipple . . . . . 2 CH
2 1/4" Gauge Test Valve . . 2 46-005-1-002 24 1/2" x 9-1/2" Nipple . . . . . 1 CH
3 1/2" Swing Check Valve . 1 46-049-1-004 25 3/4" x Close Nipple . . . . . 2 CH
4 3/4" Swing Check Valve . 1 46-049-1-005 26 3/4" x 1-1/2" Nipple . . . . . 1 CH
5 1/2" Globe Valve . . . . . . . 1 46-047-1-004 27 3/4" x 2-1/2" Nipple . . . . . 1 CH
6 1/2" Y-Strainer . . . . . . . . . 1 52-353-1-005 28 3/4" x 3" Nipple . . . . . . . . 1 CH
7 Restriction Assembly . . . . 1 92-210-2-005 29 3/4" x 4-1/2" Nipple . . . . . 1 CH
8 2" Globe Valve . . . . . . . . . 1 46-047-1-009 30 2" x 2-1/2" Nipple . . . . . . . 1 CH
9 1/4" Plug . . . . . . . . . . . . . 2 CH 31 2" x 3" Nipple . . . . . . . . . . 1 CH
10 1/2" Union . . . . . . . . . . . . 2 CH
11 3/4" Union . . . . . . . . . . . . 1 CH
NOTES:
12 1/2" 90 Elbow . . . . . . . . . 3 CH
13 1/2" Tee . . . . . . . . . . . . . . 1 CH 1. All Fittings and Nipples are galvanized
14 1/2" x 1/2" x 3/4" Tee . . . . 1 CH (Standard Order).
15 3/4" x 1/4" x 3/4" Tee . . . . 2 CH 2. CH: Common Hardware.
16 3/4" x 3/4" x 1/2" Tee . . . . 1 CH
17 2" x 2" x 1/2" Tee . . . . . . . 1 CH
18 1/4" x 1-1/2" Nipple . . . . . 2 CH SYSTEM
19 1/2" x 1-1/2" Nipple . . . . . 5 CH PRESSURE
1 GAUGE
20 1/2" x 2" Nipple . . . . . . . . 2 CH
21 1/2" x 3" Nipple . . . . . . . . 1 CH SUPPLY
PRESSURE
9 2 GAUGE
1
3/4 INCH NPT 1/2 INCH NPT 18 25
CONNECTION CONNECTION 9
15
FOR WATER FOR WATERFLOW 29 2
MOTOR PRESSURE 25
ALARM ALARM SWITCH 18
ORDERED 11
4
SEPARATELY 15
LOCATION 27
(FOR VARIABLE
FOR OPTIONAL 26
PRESSURE HANDHOLE
ELECTRICALLY
SYSTEMS) 16 COVER MUST
SUPERVISED
N.O. ALARM BE AT LEAST
CONTROL MODEL RC-1 30 INCHES
VALVE RETARD AWAY FROM
(BVS-3/4") CHAMBER 28 A WALL
23

5
1/2 INCH NPT
CONNECTION 22
FOR WATERFLOW
PRESSURE
ALARM 12
SWITCH ALARM
20 TEST VALVE
3/4 INCH NPT (NORMALLY
10 CLOSED)
CONNECTION
FOR WATER 22
MOTOR 14
ALARM 31
MODEL AV-1
13 ALARM VALVE,
LOCATION 23
FOR OPTIONAL 8 INCH (DN200)
RESTRICTION FLANGE x
ELECTRICALLY
ASSEMBLY, MAIN GROOVE
SUPERVISED
SEE FIGURE 3 DRAIN VALVE 8 SHOWN
N.O. ALARM
(NORMALLY
CONTROL 19 24 CLOSED) 30
VALVE
7 20 21
(BVS-1/2")
17
19

10
19 6 19
12 19 2 INCH NPT
3
12 CONNECTION
TO DRAIN

FIGURE 6 PART 2 OF 2
HORIZONTAL CLOSED DRAIN TRIM SPECIAL ORDER
FOR 8 INCH (DN200) MODEL AV-1-300 ALARM CHECK VALVES (52-204-2-058)
Page 14 of 22 TFP910

C
Vertical Closed Drain Trim
Dimensions in Inches and (mm)
Dimension
With RC-1 Without RC-1
A 16-1/2 (419) 13-1/2 (343)

A B B 10-1/2 (267) 10-1/2 (267)


PLAN VIEW D C 10-1/2 (267) 10 (254)
GxG&
FxG D 8-7/8 (225) 8-7/8 (225)
RC-1
E 12-1/4 (311) 12-1/4 (311)
F
E F 16-1/2 (419) N/A

G 3 (75) 3 (75)
G

ELEVATION VIEW

Vertical Open Drain Trim


Dimensions in Inches and (mm)
Dimension
With RC-1 Without RC-1
A 15-1/2 (394) 13-1/2 (343)
A B
B 10-1/2 (267) 10-1/2 (267)
PLAN VIEW D
GxG& C 10-1/2 (267) 10 (254)
FxG
D 8-7/8 (225) 8-7/8 (225)
RC-1

F E 12-1/4 (311) 12-1/4 (311)


E
F 16-1/2 (419) N/A

G 3 (75) 3 (75)

ELEVATION VIEW

FIGURE 7 PART 1 OF 3
INSTALLATION DIMENSIONS
FOR 2-1/2 INCH (DN65) MODEL AV-1-300 ALARM CHECK VALVES
TFP910 Page 15 of 22

Vertical Closed Drain Trim


C Dimensions in Inches and (mm)
Dimension With RC-1 Without RC-1
4 Inch (DN100) 6 Inch (DN150) 4 Inch (DN100) 6 Inch (DN150)
A 19 (483) 19 (483) 19 (483) 19 (483)

B 10-1/2 (267) 11-1/4 (286) 10-1/2 (267) 11-1/4 (286)

A B C 10-1/2 (267) 11-1/2 (292) 10-1/2 (267) 11-1/2 (292)


PLAN VIEW D
10-1/4 (260) 12-1/4 (311) 10-1/4 (260) 12-1/4 (311)
(G x G)
D
10 (254) 12 (305) 10 (254) 12 (305)
RC-1 (F x F)
D
10 (254) 12 (305) 10 (254) 12 (305)
F (F x G)
E
D
E 12-1/2 (318) 15 (381) 12-1/2 (318) 15 (381)

F 15-1/2 (394) 15-1/2 (394) 11-1/2 (292) 11-1/2 (292)


G
G 3 (75) 2-3/4 (70) 3 (75) 2-3/4 (70)
ELEVATION VIEW

Vertical Open Drain Trim


C Dimensions in Inches and (mm)
Dimension With RC-1 Without RC-1
4 Inch (DN100) 6 Inch (DN150) 4 Inch (DN100) 6 Inch (DN150)
A 19 (483) 19 (483) 19 (483) 19 (483)

B 10-1/2 (267) 11-1/4 (286) 10-1/2 (267) 11-1/4 (286)


A B
C 10-1/2 (267) 11-1/2 (292) 10-1/2 (267) 11-1/2 (292)
PLAN VIEW
D
10-1/4 (260) 12-1/4 (311) 10-1/4 (260) 12-1/4 (311)
(G x G)
D
RC-1 10 (254) 12 (305) 10 (254) 12 (305)
(F x F)
D
F 10 (254) 12 (305) 10 (254) 12 (305)
E (F x G)
D
E 12-1/2 (318) 15 (381) 12-1/2 (318) 15 (381)

F 15-1/2 (394) 15-1/2 (394) 11-1/2 (292) 11-1/2 (292)


G
G 3 (75) 2-3/4 (70) 3 (75) 2-3/4 (70)
ELEVATION VIEW

Horizontal Closed Drain Trim


Dimensions in Inches and (mm)
D Dimension With RC-1 Without RC-1
B 4 Inch (DN100) 6 Inch (DN150) 4 Inch (DN100) 6 Inch (DN150)
A
10-1/4 (260) 12-1/4 (311) 10-1/4 (260) 12-1/4 (311)
RC-1 (G x G)
A
10 (254) 12 (305) 10 (254) 12 (305)
(F x F)
A
10 (254) 12 (305) 10 (254) 12 (305)
E (F x G)
B 15 (381) 15 (381) 10-1/2 (267) 11-1/2 (292)

C A
C 3-1/4 (83) 3-1/4 (83) 3-1/4 (83) 3-1/4 (83)

ELEVATION VIEW PLAN VIEW D 14 (356) 15 (381) 14 (356) 15 (381)

E 13-3/4 (349) 14-3/4 (375) 13-3/4 (349) 14-3/4 (375)

FIGURE 7 PART 2 OF 3
INSTALLATION DIMENSIONS
FOR 4 & 6 INCH (DN100 & DN150) MODEL AV-1-300 ALARM CHECK VALVES
Page 16 of 22 TFP910

Vertical Closed Drain Trim


Dimensions in Inches and (mm)
Dimension
With RC-1 Without RC-1
A 18-1/2 (470) 15-3/4 (400)

D B 16-1/8 (410) 16-1/8 (410)


A B FxF
PLAN VIEW FxG& C 12 (305) 12 (305)
GxG
D 14 (356) 14 (356)

RC-1 E 16-1/2 (419) 16-1/2 (419)


F E F 15-1/2 (394) N/A

G 2-1/2 (64) 2-1/2 (64)

ELEVATION VIEW

Vertical Open Drain Trim


Dimensions in Inches and (mm)
Dimension
With RC-1 Without RC-1
A 18-1/2 (470) 15-3/4 (400)

D B 16-1/8 (410) 16-1/8 (410)


A B FxF
PLAN VIEW FxG& C 12 (305) 12 (305)
GxG
D 14 (356) 14 (356)

RC-1 E 16-1/2 (419) 16-1/2 (419)


F E F 15-1/2 (394) N/A

G 3-1/2 (89) 3-1/2 (89)

ELEVATION VIEW

Horizontal Closed Drain Trim


D Dimensions in Inches and (mm)
Dimension
B With RC-1 Without RC-1
A 14 (356) 14 (356)

B 15 (381) 12 (305)

C 1-1/2 (38) N/A

RC-1 E D 19-1/2 (495) 19-1/2 (495)


A
FxF
C E 16-1/2 (419) 16-1/2 (419)
FxG&
GxG
ELEVATION VIEW PLAN VIEW
FIGURE 7 PART 3 OF 3
INSTALLATION DIMENSIONS
FOR 8 INCH (DN200) MODEL AV-1-300 ALARM CHECK VALVES
TFP910 Page 17 of 22

Step 7. Fully open the main control Valves do not require any regularly
NO. DESCRIPTION QTY. P/N
valve. scheduled maintenance. It is recom-
1 3/4" x 1/4" Hex mended, however, that proper opera-
Bushing . . . . . . . . . . . . . 1 CH Step 8. Open the end-of-line Inspec-
tion of the alarms be periodically veri-
2 3/32" Vent Fitting . . . . . . 1 92-032-1-002 tors Test Connection (or Alarm Test
fied in accordance with a procedure
3 1/4" x 5'-0" Tubing . . . . . 1 CH Valve, if acceptable to the authority
that is acceptable to the authority hav-
having jurisdiction) and verify that the
PRESSURE ing jurisdiction. Any impairment must
system alarms operate.
SWITCH be immediately corrected.
NOTE
NOTE
Notify the proper authorities and all
1 Performing the care and maintenance
personnel who may be affected that an
3 procedures will result in operation of
alarm test is to be performed.
(ROUTE TO the associated alarms. Consequently,
DRAIN) Step 9. Close the end-of-line Inspec- notification must first be given to the
2
tors Test Connection (or Alarm Test owner and fire department, central sta-
MODEL RC-1 Valve). tion, or other signal station to which the
RETARD (GREEN
TINT) alarms are connected.
CHAMBER Step 10. Verify that water ceases to
flow from the alarm line drain. If water Before closing a fire protection system
FIGURE 8 continues to flow, follow the corrective main control valve for maintenance
ALARM VENT TRIM procedure described in the Mainte- work on the fire protection systems
(52-201-2-012) nance and Service section. that it controls, permission to shut
down the affected fire protection sys-
Ordered separately NOTE tems must first be obtained from the
when a Water Motor Alarm is not The Restriction Assembly has a 1/8 proper authorities, and all personnel
installed inch (3,2 mm) diameter drain orifice. who may be affected by this decision
Sufficient time must be allowed for must be notified.
drainage of the Retard Chamber and
the piping to the water motor alarm. Inspection Procedure
It is recommended that the following
Step 11. Once it has been verified that inspection procedure be performed at
the flow of water out of the alarm line least quarterly by a qualified Inspec-
drain has stopped, the alarm valve is tion Service:
set and is ready for service.
Setting Step 1. Notify the proper authorities
and all personnel who may be affected
NOTE
Procedure After placing a fire protection system that an alarm test is to be performed.
in service, notify the proper authorities Step 2. Open the end-of-line Inspec-
Steps 1 through 11 are to be per- and advise those responsible for moni-
formed when initially setting the Model tors Test Connection (or Alarm Test
toring proprietary and/or central sta- Valve, if acceptable to the authority
AV-1-300 Alarm Check Valve or after tion alarms.
system operation due to a fire. having jurisdiction) and verify that the
system alarms operate in accordance
Step 1. Open the 1/4 inch Gauge Test
Valves for the Supply and System Care and with the requirements of the authority
having jurisdiction. Verify that the
Pressure Gauges.
Step 2. Check to see that the Hand-
Maintenance water motor alarm and/or the pressure
alarm switch properly actuate and
hole Cover bolts are tight. If not, cross- The following procedures and inspec- within the elapsed time required by the
tighten them. tions should be performed as indi- authority having jurisdiction.
cated, in addition to any specific re- Step 3. Verify that water is flowing out
Step 3. Close the Alarm Test Valve. quirements of the NFPA. Any of the alarm line drain at a rate consis-
Step 4. Open the remote cross main impairment must be immediately cor- tent with the 1/8 inch (3,2 mm) diame-
or branch line vent connection (Ref. rected. ter drain orifice in the Restriction As-
Step 7 in the Installation section). The owner is responsible for the in- sembly.
Step 5. Slowly open the main control spection, testing, and maintenance of Step 4. Close the end-of-line Inspec-
valve until the sound of flowing water their fire protection system and de- tors Test Connection (or Alarm Test
just begins and then open the valve vices in compliance with this docu- Valve).
one more turn. ment, as well as with the applicable
standards of the National Fire Protec- Step 5. Verify that water ceases to flow
NOTE tion Association (e.g., NFPA 25), in from the alarm line drain.
Filling the system with water will result addition to the standards of any Step 6. Clean the 1/2 inch Strainer
in operation of the associated alarms. authority having jurisdiction. The in- (located in the valve trim) as well as
Consequently, notification must first stalling contractor or product manufac- the 3/4 inch Strainer (located at the
be given to the owner and fire depart- turer should be contacted relative to connection to the water motor alarm,
ment, central station, or other signal any questions. as applicable). Be sure to replace the
station to which the alarms are con- It is recommended that automatic strainer baskets and tighten the caps
nected. sprinkler systems be inspected, securely.
Step 6. Close the remote branch line tested, and maintained by a qualified
vent connection after the discharge of Inspection Service. NOTE
aerated water ceases, and the outlet Cleaning of the Strainers after each
The Model AV-1-300 Alarm Check operation of the alarms is especially
has flowed full for at least 15 seconds.
Page 18 of 22 TFP910

important in the case of water supplies noted in Step No. 5 is from the Alarm NOTE
(such as lakes and rivers) having a Port, drain the system in accordance Loss of excess system pressure will
large quantity of suspended matter. A with the prescribed procedure. After increase the likelihood of a false alarm
clogged alarm line can prevent opera- the system has been drained, remove in the case of a variable pressure sys-
tion of the alarms. the Handhole Cover. tem.
Step 7. Notify all authorities responsi- While holding the Spring down by the Follow the procedure indicated below
ble for monitoring the installation that coils, remove the Hinge Pin. Remove to correct a loss of excess system
the fire protection system has been the Spring and Clapper Assembly). pressure condition.
returned to service.
Step 7. Using a light, check for and Step 1. Check for signs of continued
remove any debris that may have be- leakage from the alarm line drain. If
Sprinkler System Drain-Down come lodged within the Seat Ring rust stains and/or water deposits indi-
Draining the sprinkler system must be groove. Inspect the Seat Ring seat for cate that continued leakage has been
done in accordance with the following any damage. If the Seat Ring has be- taking place, take corrective action ac-
procedure: come dented across the seat then the cording to the procedure described in
Alarm Check Valve will have to be the sub-section entitled Leakage
Step 1. Close the main control valve, replaced. It is impractical to re-face a From Alarm Line Drain.
if this has not already been done. Seat Ring in the field.
Step 2. If there are no signs of contin-
Step 2. Open the remote cross main Step 8. Check for and remove any ued leakage from the alarm line drain,
or branch line vent connection (Ref. debris that may have become lodged close the main control valve, slowly
Step 7 in the Installation section). in the Clapper Facing. If a minor imper- remove the plug from the supply pres-
Step 3. Open the Main Drain Valve. fection remains in the Clapper Facing, sure gauge test valve to relieve the
Check first to see that the drainage then turn it over after thoroughly clean- supply pressure, and then slowly open
water discharge will not cause damage ing both surfaces with a clean cloth. the union in the externally mounted
or result in dangerous conditions. Replace the Clapper Facing if neces- bypass.
sary. Be sure to securely re-tighten the
Step 4. Wait until the Supply Pressure Check for leakage past the Bypass
retaining fastener for the Clapper
Gauge reads zero pressure and the Check Valve. If there is leakage, de-
Washer.
sound of draining water has stopped bris may have become lodged be-
before performing any maintenance Step 9. Replace the Spring and Clap- tween its clapper and seat. Drain the
work on the fire protection system. per Assembly as shown in Figure 1. system in accordance with the pre-
While holding the coils of the Spring scribed procedure and then clean or
down, re-insert the Hinge Pin. Be sure replace the Bypass Check Valve as
Leakage from Alarm Line Drain that the Hinge Pin is pushed all the way required.
Follow the steps indicated below until to the rear of the valve.
Re-assemble the externally mounted
water ceases to flow from the alarm Step 10. Replace the Handhole Cover. bypass, replace the plug into the
line drain. Check for the discontinu- Return the Alarm Valve to operation in Gauge Test Valve, and return the fire
ation of the leakage after each step is accordance with the steps described protection system to operation in ac-
complete. in the Setting Procedure section. cordance with the steps described in
Step 1. Open the Main Drain Valve. the Operating Procedure section.
Let the water flow for about 5 seconds Step 3. If there are no signs of leakage
and then close the Main Drain Valve. Clogged Alarm Line Drain
If water either does not flow or only past either the Alarm Check Valve
This should flush any loose debris that Clapper per Step 1 or the Bypass
may have become trapped between dribbles out of the alarm line drain
during an alarm test, then it is likely Check Valve per Step 2, inspect the
the Clapper Facing and the Seat Ring sprinkler system for leakage.
or in the seating area of the Drain that the screen protecting the Restric-
Valve. tion Assembly drain orifice (Ref. Fig-
ure 3) has become clogged.
Step 2. Repeat Step No. 1 if the rate Excess Pressure Due To Thermal
of continued flow out of the drain was Expansion
NOTE
noticeably reduced. Wet pipe sprinkler systems subject to
A clogged alarm line drain will increase
ambient temperatures in excess of
Step 3. Open the Alarm Test Valve the likelihood of a false alarm in the
100F/38C can experience signifi-
and allow water to flow for about 5 case of a variable pressure system.
cant increases in system pressure due
seconds before re-closing the valve. First break the union downstream of to the thermal expansion of the water.
This should flush any loose debris that the Drain Restriction and remove the In particular, a gridded wet-pipe sys-
may have become trapped in the seat- Drain Restriction for cleaning by back- tem with a relatively small air pocket
ing area of the Alarm Test Valve. flushing the screen. Re-install the and no relief valve can be subjected to
Step 4. Repeat Step No. 3 if the rate Drain Restriction and re-assemble the an increase of more than 100 psi (6,9
of continued flow out of the drain was drain line. bar), due to an increase in ambient
noticeably reduced. temperature of approximately
50F/28C.
Step 5. Determine whether the water Loss of Excess System Pressure
is flowing from the Alarm Port (Figure In the case of a variable pressure sys- As necessary, install a pressure relief
1) or past the Alarm Test Valve. If the tem, the System Pressure Gauge valve, in accordance with the require-
leakage is past the Alarm Test Valve, should normally indicate a pressure ments of the authority having jurisdic-
close the main control valve, and then greater than that shown by the Supply tion, to automatically relieve the ex-
repair or replace the Alarm Test Valve Pressure Gauge. Also, the value cess pressure which could otherwise
as necessary. should be close to that of the peak be created in wet-pipe systems that
supply pressure that has occurred af- are exposed to significant increases in
Step 6. If it appears that the leakage ambient temperature.
ter the system was placed in service.
TFP910 Page 19 of 22

False Alarms
If repeated false alarms occur in a vari-
able pressure system:
Limited
Step 1. Check for and correct the Warranty
cause of continued leakage out the Products manufactured by Tyco Fire &
alarm line drain. Building Products (TFBP) are war-
Step 2. Check for and clean a clogged ranted solely to the original Buyer for
alarm line drain. ten (10) years against defects in mate-
rial and workmanship when paid for
Step 3. Check for and correct the and properly installed and maintained
cause of a loss in excess system pres- under normal use and service. This
sure. warranty will expire ten (10) years
Step 4. Drain the sprinkler system and from date of shipment by TFBP. No
re-fill it in accordance with the steps warranty is given for products or com-
described in the Setting Procedure ponents manufactured by companies
section. not affiliated by ownership with TFBP
or for products and components which
Intermittent Alarms have been subject to misuse, improper
If the pressure alarm switch gives a installation, corrosion, or which have
steady signal, but the water motor gen- not been installed, maintained, modi-
erates an intermittent alarm, check for fied or repaired in accordance with ap-
binding in the water motor alarm drive plicable Standards of the National Fire
shaft. Protection Association, and/or the
standards of any other Authorities
If the water motor alarm and/or the Having Jurisdiction. Materials found
pressure alarm switch provide an in- by TFBP to be defective shall be either
termittent alarm, it is likely the conse- repaired or replaced, at TFBPs sole
quence of an excessive amount of air option. TFBP neither assumes, nor
being trapped within the sprinkler sys- authorizes any person to assume for it,
tem. Drain down the sprinkler system any other obligation in connection with
and re-fill it in accordance with the the sale of products or parts of prod-
steps described in the Setting Proce- ucts. TFBP shall not be responsible for
dure section. sprinkler system design errors or inac-
A discontinuance of an alarm may also curate or incomplete information sup-
be caused by the Clapper closing due plied by Buyer or Buyers repre-
to a sudden drop in supply pressure or sentatives.
the shut-off of a pump in the supply In no event shall TFBP be liable, in
line. These types of problems can only contract, tort, strict liability or under
be corrected by maintaining a steady any other legal theory, for incidental,
supply pressure. indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBPs liability exceed an amount
equal to the sales price.
The foregoing warranty is made in lieu
of any and all other warranties, ex-
press or implied, including warranties
of merchantability and fitness for a par-
ticular purpose.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity, in
whole or part, of any portion of this
warranty will not affect the remainder.
Page 20 of 22 TFP910

Standard Order AV-1-300 Valve Replacement Valve Parts:


Ordering Trim: Specify: (description) for use with
(specify) size Model AV-1-300 Alarm
Procedure Specify: Vertical, Closed Drain Galva-
nized Trim for (specify size) Model AV-
Check Valve, P/N (see Figure 1).
1-300 Alarm Check Valve, P/N (spec- Replacement Trim Parts :
NOTES
ify). Specify: (description) for use with
Refer to Table A (Page 3) for Flange
Drilling Specifications. Model AV-1-300 Alarm Check Valve,
Vertical Closed Drain, P/N (see Figure 3, 4, or 5).
Part Numbers for factory pre-trimmed Galvanized
Model AV-1-300 Valves are provided (See Figure 3)
in the Price Book. 2-1/2 inch . . . . . . . . . . . . . . P/N 52-204-2-050
4 or 6 inch*. . . . . . . . . . . . . P/N 52-204-2-951 Other AV-1-300 Alarm Check
Standard AV-1-300 Alarm Check 8 inch* . . . . . . . . . . . . . . . . P/N 52-204-2-952 Valves:
Valve (American Standard Flange *Provided semi-preassembled.
Drilling, American Threaded Ports, NOTES
and American Groove Outside Di- Special Order AV-1-300 Valve Trim: Other AV-1-300 Alarm Check Valves
ameter, as applicable): Specify: )Vertical or Horizontal), are valves ordered with any combina-
Specify: (specify size inch) Model (Closed or Open) Drain Galvanized tion of flange, threaded port, or groove
AV-1-300 Alarm Check Valve with Trim for (specify size) Model AV-1-300 outside diameter not offered under
(specify end connections), P/N (spec- Alarm Check Valve, P/N (specify). Standard AV-1-300 Alarm Check
ify). Valve offerings.
Vertical Open Drain,
2-1/2 Inch G x G Galvanized Valves with NPT threaded ports are
2.88 inch (73,0 mm) (See Figure 4) intended for use with the AV-1-300
Groove O.D. x 2.88 2-1/2 inch . . . . . . . . . . . . . . P/N 52-204-2-053 Valve Trim described in this data
inch (73,0 mm) 4 or 6 inch*. . . . . . . . . . . . . P/N 52-204-2-954 sheet. Valves with ISO threaded ports
Groove O.D. . . . . . . . . . P/N 52-203-1-110 8 inch* . . . . . . . . . . . . . . . . P/N 52-204-2-955 are intended for use with special order
2-1/2 Inch F x G *Provided semi-preassembled.
ANSI Flange x
trim that is provided by local distribu-
2.88 inch (73,0 mm) Horizontal Closed tors to meet the specific needs of cer-
Groove O.D. . . . . . . . . . P/N 52-203-1-210 Drain, tain localities. Please contact your lo-
Galvanized cal distributor regarding valves and
4 Inch G x G (See Figure 5) valve trim for specific localities.
4.50 inch (114,3 mm) 4 or 6 inch . . . . . . . . . . . . . P/N 52-204-2-057
Groove O.D. x 4.50 8 inch . . . . . . . . . . . . . . . . . P/N 52-204-2-058 Specify: (specify size) Model AV-1-
inch (114,3 mm) 300 Alarm Check Valve with (specify)
Groove O.D. . . . . . . . . . P/N 52-203-1-113 Accessories: connections with (specify NPT or ISO)
4 Inch F x G
ANSI Flange x Order the following accessories, as threaded ports, P/N (See Page 21).
4.50 inch (114,3 mm) applicable:
Groove O.D. . . . . . . . . . P/N 52-203-1-413
4 Inch F x F Model RC-1
ANSI Flange x Retard Chamber
ANSI Flange . . . . . . . . . P/N 52-203-1-013 (required for variable
pressure water supply
6 Inch G x G conditions) . . . . . . . . . . P/N 52-211-2-002
6.62 inch (168,3 mm) Alarm Vent Trim
Groove O.D. x 6.62 (required when a
inch (168,3 mm) water motor alarm is
Groove O.D. . . . . . . . . . P/N 52-203-1-115 not installed). . . . . . . . . P/N 52-201-2-012
6 Inch F x G Model PS10-2A
ANSI Flange x Potter Electric
6.62 inch (168,3 mm) Waterflow
Groove O.D. . . . . . . . . . P/N 52-203-1-615 Pressure Alarm Switch
6 Inch F x F (required for electric
ANSI Flange x signal indicating
ANSI Flange . . . . . . . . . P/N 52-203-1-015 waterflow) . . . . . . . . . . . P/N 54-281-1-002
Model WMA-1
8 Inch G x G Water Motor Alarm
8.62 inch (219,1 mm) (required for a
Groove O.D x 8.62 mechanical waterflow
inch (219,1 mm) alarm) . . . . . . . . . . . . . . P/N 52-630-1-001
Groove O.D. . . . . . . . . . P/N 52-203-1-916
8 Inch F x G
ANSI Flange x
8.62 inch (219,1 mm)
Groove O.D. . . . . . . . . . P/N 52-203-1-816
8 Inch F x F
ANSI Flange x
ANSI Flange . . . . . . . . . P/N 52-203-1-016
TFP910 Page 21 of 22

Part Numbers For Other Part Numbers For Other Part Numbers For Other
Model AV-1-300 Alarm Valves: Model AV-1-300 Alarm Valves: Model AV-1-300 Alarm Valves:

Other 2-1/2 Inch Valves with NPT Other 6 Inch Valves with NPT Ports Other 8 Inch Valves with NPT Ports
Ports ANSI Flange x ISO (PN10) Flange x
ISO (PN16) Flange x 6.50 inch (165,1 8.62 inch (219,1
2.88 inch (73,0 mm) mm) Groove O.D . . . . . P/N 52-203-1-625 mm) Groove O.D . . . . . . P/N 52-203-1-896
Groove O.D . . . . . . . . . . P/N 52-203-1-251 ISO (PN16) Flange x ISO (PN16) Flange x
ANSI Flange x 6.62 inch (168,3 8.62 inch (219,1
3.00 inch (76,1 mm) mm) Groove O.D . . . . . P/N 52-203-1-695 mm) Groove O.D . . . . . . P/N 52-203-4-266
Groove O.D . . . . . . . . . . P/N 52-203-1-220 ISO (PN16) Flange x ISO (PN10) Flange x
ISO (PN16) Flange x 6.50 inch (165,1 ISO (PN10) Flange . . . . P/N 52-203-4-016
3.00 inch (76,1 mm) mm) Groove O.D . . . . . P/N 52-203-5-215 ISO (PN16) Flange x
Groove O.D . . . . . . . . . . P/N 52-203-1-331 ISO (PN16) Flange x ISO (PN16) Flange . . . . P/N 52-203-4-118
AS Flange x ISO (PN16) Flange . . . P/N 52-203-4-015 AS Flange x
2.88 inch (73,0 mm) AS Flange x AS Flange . . . . . . . . . . . P/N 52-203-4-316
Groove O.D . . . . . . . . . . P/N 52-203-1-611 AS Flange. . . . . . . . . . . P/N 52-203-4-315 AS Flange x
AS Flange x AS Flange x 8.62 inch (219,1
3.00 inch (76,1 mm) 6.62 inch (168,3 mm) Groove O.D . . . . . . P/N 52-203-4-416
Groove O.D . . . . . . . . . . P/N 52-203-4-410 mm) Groove O.D . . . . . P/N 52-203-4-415 JIS Flange x
JIS Flange x AS Flange x JIS Flange . . . . . . . . . . . P/N 52-203-1-716
2.88 inch (73,0 mm) 6.50 inch (165,1 JS Flange x
Groove O.D . . . . . . . . . . P/N 52-203-1-710 mm) Groove O.D . . . . . P/N 52-203-4-425 8.62 inch (219,1
JIS Flange x JIS Flange x mm) Groove O.D . . . . . . P/N 52-203-4-816
3.00 inch (76,1 mm) JIS Flange . . . . . . . . . . P/N 52-203-4-715
Groove O.D . . . . . . . . . . P/N 52-203-1-810 JIS Flange x
3.00 inch (76,1 mm) 6.62 inch (168,3 Other 8 Inch Valves with ISO Ports
Groove O.D x mm) Groove O.D . . . . . P/N 52-203-4-815 ISO (PN10) Flange x
3.00 inch (76,1 mm) JIS Flange x ISO (PN10) Flange . . . . P/N 52-203-4-116
Groove O.D . . . . . . . . . . P/N 52-203-1-120 6.50 inch (165,1 ISO (PN16) Flange x
mm) Groove O.D . . . . . P/N 52-203-5-815 ISO (PN16) Flange . . . . P/N 52-203-4-117
6.50 inch (165,1 mm) ISO (PN10) Flange x
Other 2-1/2 Inch Valves with ISO Groove O.D x 8.62 inch (219,1
Ports 6.50 inch (165,1
ISO (PN16) Flange x mm) Groove O.D. . . . . . P/N 52-203-4-216
mm) Groove O.D . . . . . P/N 52-203-1-124 ISO (PN16) Flange x
2.88 inch (73,0 mm)
Groove O.D . . . . . . . . . . P/N 52-203-1-211 8.62 inch (219,1
ISO (PN16) Flange x mm) Groove O.D. . . . . . P/N 52-203-4-226
3.00 inch (76,1 mm) Other 6 Inch Valves with ISO Ports 8.62 inch (219,1 mm)
Groove O.D . . . . . . . . . . P/N 52-203-1-311 ISO (PN16) Flange x Groove O.D. x
3.00 inch (76,1 mm) ISO (PN16) Flange . . . P/N 52-203-4-115 8.62 inch (219,1
Groove O.D x ISO (PN16) Flange x mm) Groove O.D. . . . . . P/N 52-203-1-926
3.00 inch (76,1 mm) 6.62 inch (168,3
Groove O.D . . . . . . . . . . P/N 52-203-4-120 mm) Groove O.D . . . . . P/N 52-203-4-215
2.88 inch (73,0 mm) ISO (PN16) Flange x
Groove O.D x 6.50 inch (165,1
2.88 inch (73,0 mm) mm) Groove O.D . . . . . P/N 52-203-4-225
Groove O.D . . . . . . . . . . P/N 52-203-1-921 6.62 inch (168,3 mm)
Groove O.D x
6.62 inch (168,3
mm) Groove O.D . . . . . P/N 52-203-1-925
6.50 inch (165,1 mm)
Groove O.D x
Part Numbers For Other 6.50 inch (165,1
Model AV-1-300 Alarm Valves: mm) Groove O.D . . . . . P/N 52-203-1-125

Other 4 Inch Valves with NPT Ports


ISO (PN16) Flange x
4.50 inch (114,3
mm) Groove O.D. . . . . . P/N 52-203-1-493
ISO (PN16) Flange x
ISO (PN16) Flange . . . . P/N 52-203-4-013
AS Flange x
AS Flange . . . . . . . . . . . P/N 52-203-4-313
AS Flange x
4.50 inch (114,3
mm) Groove O.D. . . . . . P/N 52-203-4-413
JIS Flange x
JIS Flange . . . . . . . . . . . P/N 52-203-4-713
JIS Flange x
4.50 inch (114,3
mm) Groove O.D. . . . . . P/N 52-203-4-813

Other 4 Inch Valves with ISO Ports


ISO (PN16) Flange x
ISO Flange . . . . . . . . . . P/N 52-203-4-113
ISO (PN16) Flange x
4.50 inch (114,3
mm) Groove O.D. . . . . . P/N 52-203-4-213
4.50 inch (114,3 mm)
Groove O.D x
4.50 inch (114,3
mm) Groove O.D. . . . . . P/N 52-203-1-923
Page 22 of 22 TFP910

TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446

Вам также может понравиться